Yarisworld Archive

Want to build costom turbo kit. Need advice from boosted guys!

610 posts · 163,166 views · page 10 of 13

Replies continued

cali yarisCanoga Park, CA · Apr 21, 2012#451
I've been running stock valves for quite a while with pretty tough track days included. We did put stiffer springs on them so I could rev to 7300.

I'll check our sources and see if anyone else is making valves. You want stock or over-size?
Bluevitz-rsOshawa, Ontario, Canada · Apr 22, 2012#452
Originally Posted by pimp my yaris ↑
? Who is making performance valve springs besides Ferrea. 1000$ for valves and spring is a little stiff. And stock seem a little weak for my extended high RPM abuse.
There's Ferrea valves for sale in the FS section... have a looksee
pimp my yarisThread starterchicago · Apr 22, 2012#453
Im just looking for valve springs. What Brand are U running Garm. And do you sell them?
cali yarisCanoga Park, CA · Apr 22, 2012#454
bluevitz, those oversized valves would be a substantial project on the head, I'm sure you know that; unless someone can do machining and such themselves.

I don't know what springs we have in my car, but Ferrea is making us an upgraded valve spring kit that supposedly would be ready by now. You know how that goes. 🙁

I will follow up with them on Monday.
Blown_xaVirginia · Apr 22, 2012#455
From assembling a few different Toyota motors, I can tell you that the Scion tC motor has the same dimension valve springs. So I've thought about just purchasing upgraded springs ( advertised for the tC) and using those.

I guess I have lucked out, using stock head and my limiter is set to 7300rpm. I've even slammed it in the wrong gear a few times and the rpm shot well past what the tach shows (8000 rpm). I'm pretty sure it was about 9000 rpm once when I was at the dragstrip and put it in second instead of 4th. I think the only reason I didnt get valve contact was because maybe the valves cleared the lower compression pistons even with float. I did hear a noise afterwards which scared me for a few minutes, until I figured out that my power steering belt flipped upside down! Lol
ViperoniBrampton, ON · Apr 22, 2012#456
Originally Posted by Blown_xa ↑
I did hear a noise afterwards which scared me for a few minutes, until I figured out that my power steering belt flipped upside down! Lol
You had this happen to you too? When it happened to me, I couldn't believe it.
Blown_xaVirginia · Apr 22, 2012#457
Originally Posted by Viperoni ↑
You had this happen to you too? When it happened to me, I couldn't believe it.
Yea, I don't even understand the physics behind how that can even occur.
pimp my yarisThread starterchicago · Apr 22, 2012#458
Got some real work done today. I had to stop I did not have a 8mm by-hexagon socket to remove my head bolts. Ordered one today.

2 attachments not included in this copy

pimp my yarisThread starterchicago · Apr 22, 2012#459
more pics

1 attachment not included in this copy

cali yarisCanoga Park, CA · Apr 23, 2012#460
mmmm, a build thread... thank you. 🙇
ViperoniBrampton, ON · Apr 23, 2012#461
Originally Posted by Blown_xa ↑
Yea, I don't even understand the physics behind how that can even occur.
Me neither.
When I saw the belt grooves staring at me, I had to do a double take. I KNOW I put the belt on properly because I saw the "Goodyear gatorback" logo looking at me lol.



FWIW, My motor's also seens over 8k from a couple of mis-shifts, still works good :)
Bluevitz-rsOshawa, Ontario, Canada · Apr 23, 2012#462
My motor saw about 8600 once from a miss shift from redline in 3rd back to 2nd passing two gravel trucks. 3 valves did not survive and it sounded like someone threw gravel IN the motor. Scared the shit outa me. But the funny thing was it never set a code and had no choose but to continue driving it for the next 250km on my trip LOL.
suckerfaceMilwaukee, WI · Apr 24, 2012#463
Slightly off topic, but where in Chicago are you Pimp? I'd love to come check out your work and offer any assistance on the weekends if you need it, and with being in Milwaukee, it's only a 2-3 hour drive. I want to do a turbo build myself eventually, but want to see things first hand to get a better understanding of what all is involved.
ParmasML · Apr 24, 2012#464
Originally Posted by Blown_xa ↑
From assembling a few different Toyota motors, I can tell you that the Scion tC motor has the same dimension valve springs. So I've thought about just purchasing upgraded springs ( advertised for the tC) and using those.

I guess I have lucked out, using stock head and my limiter is set to 7300rpm. I've even slammed it in the wrong gear a few times and the rpm shot well past what the tach shows (8000 rpm). I'm pretty sure it was about 9000 rpm once when I was at the dragstrip and put it in second instead of 4th. I think the only reason I didnt get valve contact was because maybe the valves cleared the lower compression pistons even with float. I did hear a noise afterwards which scared me for a few minutes, until I figured out that my power steering belt flipped upside down! Lol
What compression were you running? Wow 9000rpm on stock head is a very nice dream hey !😁
Blown_xaVirginia · Apr 24, 2012#465
Originally Posted by Parmas ↑
What compression were you running? Wow 9000rpm on stock head is a very nice dream hey !😁
8.5:1 Is the compression ratio.
I was at 7300rpm in 3rd and put it in 2nd. Car sounded like a sports bike. I just did the math, there is a 31% difference in rpm drop between 2nd and 3rd gear ( xA trans). So 9563rpm is what it hit considering I shifted from 7300rpm.
This happened about a year ago.
pimp my yarisThread starterchicago · Apr 24, 2012#466
Originally Posted by suckerface ↑
Slightly off topic, but where in Chicago are you Pimp? I'd love to come check out your work and offer any assistance on the weekends if you need it, and with being in Milwaukee, it's only a 2-3 hour drive. I want to do a turbo build myself eventually, but want to see things first hand to get a better understanding of what all is involved.
Thats funny. I have relatives in Greenfield and I was just there for christmas with my car. I bought my car in Milwaukee at Heiser Toyota during the cash 4 clunkers rush.
I live in Lake in the Hills. It is in the extreme north and west end of the Chicago burbs. You are welcome to check it out when I get her back together again.
pimp my yarisThread starterchicago · Apr 25, 2012#467
Well I got the head off today and it looks good. I dont see any bent valves or impact marks on pistons. I even put it upside down and fill the head chambers with water. None leaked out. So its still likely I spun a rod bearing. I guess I will be pulling the rest of the motor this weekend. I cant believe there was no metal chips in the oil with all that noise.
fnkngrvIn The Hotbox · Apr 25, 2012#468
might as well consider buying another motor and keep your top end for a rainy day if that is the case...how many miles is on your motor again? I take it you are going to pull your bottom end apart and go from there? At least you didn't have your block turn into swiss cheese like mine.
pimp my yarisThread starterchicago · Apr 27, 2012#469
I am going to pull the bottom end on sunday and check it out. I will most likely order crower rods and je pistons and rings from this Race engineering web sight. https://www.raceeng.com/c-375-1nzfe.aspx

I am also thinking of buying a new clutch from micro image.
cali yarisCanoga Park, CA · Apr 27, 2012#470
^ They list CP pistons. I have those and Pauter rods on the shelf. I can probably beat their prices if you want JE and Crower instead.
pimp my yarisThread starterchicago · Jun 10, 2012#471
Ok, engine is built in the car and running with cp pistons and Pauter rods for those who didnt see the build thread. I am working on a return line now. I plan to drill a hole in the top of mystock rail and tap the hole. I then will screw in a -4an fitting and run that line to a boost controled fuel regulator and then back to the pump top with another hole and fitting. I was thinking of using a larger -6an line but that would be even larger then the stock feed line coming from the pump. I will also remove the stock filter and regulator and attach the feed line directly to the pump. I will attach a in line filter somewhere on the bottom of the car.
Has anyone tried this or something similar yet? Thoughts? 🤷
Garm or blown xa if you see this can you tell me what size your return line is?
fnkngrvIn The Hotbox · Jun 10, 2012#472
Wish I had my data for you Brian, but with the hiccups I am dealing with I haven't been able to get to the dyno for real world evidence to upgrade mine. It will happen before fall though.
cali yarisCanoga Park, CA · Jun 11, 2012#473
^ I'll check this morning.
pimp my yarisThread starterchicago · Jun 18, 2012#474
1200mi on the rebuilt motor. It is running great. I did a compression test yesterday after I had some tuning issues on a long road trip. All cyl. were 120-123 psi. Also no oil burning at all.

I have my fuel map perfectly tuned while in the boost. Unfortunatly my AFR's vary a lot during normal out of boost driving. Depending on engine temps. and under hood temps. Its getting pretty hot under there in 90+ degree temps.

I am thinking of hooking up my factory o2 sensor to see if this helps. I am tired of dragging my lap top around on every long trip.
pimp my yarisThread starterchicago · Jun 28, 2012#475
The new fuel rail I got from MI is awsome. I will post pictures later.
YodaFL · Jun 28, 2012#476
didn't know it was in stock. Is it the proto type?
pimp my yarisThread starterchicago · Jun 28, 2012#477
Originally Posted by Yoda ↑
didn't know it was in stock. Is it the proto type?
It is the final design. He sent me one early. The rest are going out for polishing. I was in a big hurry. I havent mounted it yet, I am still working on getting all the needed fittings. Mabe this week end I get some some real work done. 😁

2 attachments not included in this copy

cali yarisCanoga Park, CA · Jun 29, 2012#478
Should have finished and polished production stock early next week.
fnkngrvIn The Hotbox · Jun 29, 2012#479
^ Jog memory Garm, where are the inlet and outlet ports in regards to orientation drivers/passengers side? 🎉
fnkngrvIn The Hotbox · Jun 29, 2012#480
I am going in for my new tune on the 9th. I will shoot video to show fuel pressure ration under boost to add to my article on fuel system upgrading.
YodaFL · Jun 29, 2012#481
Not too bad put me down for one. Post or pm me cost so I can put it aside plz.
cali yarisCanoga Park, CA · Jun 29, 2012#482
$149.95 shipped, going up into the store today. 👍

As for direction, my regulator and gauge are on the driver side, I thought that was the inlet because of that. I will confirm with Art, I suppose it could be plumbed the other way?
ChinGyLondon · Jun 29, 2012#483
Hi, I'm in the process of fitting a turbo to my Yaris 1NZ-FE. Just wondering if you could help. Which one is the oil pressure switch, the one that sits behind the intake manifold or the one that's slightly below it?

Cali Yaris, does the fuel rail require a piece of the valve cover to be chopped off like the perrin and OBX?
fnkngrvIn The Hotbox · Jun 29, 2012#484
Originally Posted by cali yaris ↑
I will confirm with Art, I suppose it could be plumbed the other way?
Cool...I could be confused, but I thought that Art had said that was the case.
cali yarisCanoga Park, CA · Jun 29, 2012#485
Cali Yaris, does the fuel rail require a piece of the valve cover to be chopped off like the perrin and OBX?
We don't think so. My car looks intact and the rail fits nicely. I'll take some pictures today to show more detail of it installed.
cali yarisCanoga Park, CA · Jun 29, 2012#486
Here are a few shots of my set up, I think the "tabs" on the valve cover are intact.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
YodaFL · Jun 30, 2012#487
Originally Posted by cali yaris ↑
$149.95 shipped, going up into the store today. 👍

As for direction, my regulator and gauge are on the driver side, I thought that was the inlet because of that. I will confirm with Art, I suppose it could be plumbed the other way?
Ordered😁
Bluevitz-rsOshawa, Ontario, Canada · Jun 30, 2012#488
[QUOTE=cali yaris;654030]Here are a few shots of my set up, I think the "tabs" on the valve cover are intact.

No, there was a tab on the transmission side of the cover that's been removed. But it's nothing a hacksaw can't care of in short order.
Bluevitz-rsOshawa, Ontario, Canada · Jun 30, 2012#489
Originally Posted by cali yaris ↑
Here are a few shots of my set up, I think the "tabs" on the valve cover are intact.

No, there was a tab on the transmission side of the cover that's been removed. But it's nothing a hacksaw can't care of in short order.
cali yarisCanoga Park, CA · Jun 30, 2012#490
Someone please post some decent pics of their stock valve cover.
Bluevitz-rsOshawa, Ontario, Canada · Jun 30, 2012#491
Found one on eBay.

Picture not included in this copy
packetraceQuebec · Jun 30, 2012#492
Originally Posted by cali yaris ↑
Here are a few shots of my set up, I think the "tabs" on the valve cover are intact.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
Love the red strut bar color matched with valve cover :)😁
cali yarisCanoga Park, CA · Jun 30, 2012#493
blue-vitz, it doesn't look like the fuel rail would cause a problem with the driver side "tab'. My regulator doesn't have to be positioned there, which would be in the way. Maybe it's because of the intake mani instead?

I guess we'll know when pimp does his install.

@ packet -- yeah things have to match in my world or I can't sleep. Tanabe is supposed to give me a new sticker for the powdercoated strut brace.
packetraceQuebec · Jul 5, 2012#495
Garm

The black thing comin out of the regulator is for te gauge ?

What is the regulator brand ?
cali yarisCanoga Park, CA · Jul 5, 2012#496
The two inlet ports are tapped with a 9/16-18 thread. The fuel pressure gauge port is tapped with a 1/8-27 NPT.

The outlet port is located at the bottom of the fuel pressure regulator. It has a 9/16”-18 thread.

Connect the vacuum hose to the top of the fuel pressure regulator. (Hose size is a 3/16” or 5mm)
I use the AEM regulator, in stock (black).

Here is AEM's page and PDF for it:
http://www.aemelectronics.com/univer...-regulator-338

http://www.aemelectronics.com/Images...s%2025-302.pdf
packetraceQuebec · Jul 5, 2012#498
Where is the outlet of the rail going ? and where is the little black thing that comes out of the regulator going ?

Picture not included in this copy
Jeff@MicroImageSFV, CA · Jul 5, 2012#499
Originally Posted by packetrace ↑
Where is the outlet of the rail going ? and where is the little black thing that comes out of the regulator going ?

Picture not included in this copy
Fuel is being returned to the tank using the original fuel feed line (reverse direction). It's recommended to run the fuel return line when turbo, not needed on a N/A car an you can simply plug the unused end of the fuel rail.

Black hose is going to manifold vacuum/boost, FPR is rising rate based on boost, the more boost it sees the higher fuel pressure gets.
cali yarisCanoga Park, CA · Jul 5, 2012#500
The bottom of the regulator is the return line/outlet, the left is the feed from the rail, and to the right is the gauge.