Replies continued
CTScottThread starterUSA, CT · Nov 8, 2014#201 Originally Posted by
camry09 ↑ Can't seem to post an image with an url here, posts are being deleted
Sent you a PM
Thank you
OK. I got the link to the document.
Your original questions were:
Trying to install Valet 561T in 2011 Prius Sedan AT with Factory Alarm
I think i figured out the most of the things except for few
On the 4 Pin Satellate Harness there are few wires that aren't clear for me where to connect
1. Accessory Trigger ( does it go to Conn 8 Pin 2 White wire)
2. Wire 3 Starter Trigger ( does that go to Conn D8 Pin 7 )
And another thing
Heavy Gauge Relay Sattelite
1. Wire 2 Purple do i tap in to D8 Pin 7 Black starter wires ?
2. Wire 3 Orange do i tap in to D8 Pin 2 White Accesory wire?
Accessory and starter trigger on 4 pin satellite are not needed.
On the heavy gauge one:
1. To Ignition 1 on the ignition switch connector.
2. To both black wires on the ignition switch connector.
3. To Accessory wire on the ignition switch connector.
4. To power feed on fuse panel
5. To Ignition 2 on the ignition switch connector. (You will also have to go through the configuration of the remote starter to select ignition, rather than starter function.
6. To power feed on fuse panel
camry09Allentown PA · Nov 8, 2014#202Got it, thank you very much that actually clears up a lot of things
Going to bug you a bit more, on the Primary Harness
H1/1 Factory Disarm - is it necessary on Yaris?
Reason why i ask is i am planning on using H1/4 (-) Activation Input since Door Lock and Unlock are Both (-) on the Yaris
Am i on the right track for this?
thx again
CTScottThread starterUSA, CT · Nov 8, 2014#203 Originally Posted by
camry09 ↑ Got it, thank you very much that actually clears up a lot of things
Going to bug you a bit more, on the Primary Harness
H1/1 Factory Disarm - is it necessary on Yaris?
Reason why i ask is i am planning on using H1/4 (-) Activation Input since Door Lock and Unlock are Both (-) on the Yaris
Am i on the right track for this?
thx again
The Yaris doesn't have a direct disarm wire to connect to.
The activation input sounds fine.
camry09Allentown PA · Nov 8, 2014#204Appreciate all the help
So in theory even if the car is Locked by sending Activation Pulse should technically start the car, one way to find out ill be doing that in the AM first thing
camry09Allentown PA · Nov 9, 2014#205So no juice for me today unfortunately
The Valet 561T that i connected seems to be getting power because Tach Learning Procedure worked well
However the remote start doesn't work at all not even getting the ignition lights - the error that i get is Flashing LEd 7 times which according to Troubleshoot means the following
Seven (-) Neutral safety shutdown (H2/6 BLACK/WHITE)
I do have this wire connected to Key Sense - am i on the right track here ?
Thank you
CTScottThread starterUSA, CT · Nov 9, 2014#206 Originally Posted by
camry09 ↑ So no juice for me today unfortunately
The Valet 561T that i connected seems to be getting power because Tach Learning Procedure worked well
However the remote start doesn't work at all not even getting the ignition lights - the error that i get is Flashing LEd 7 times which according to Troubleshoot means the following
Seven (-) Neutral safety shutdown (H2/6 BLACK/WHITE)
I don have this wire connected to Key Sense - am i on the right track here ?
Thank you
Sounds like you didn't switch the default mode from standard transmission to auto.
camry09Allentown PA · Nov 10, 2014#207Alright maybe im missing something, but so far this is the only thing that ive found
IMPORTANT! This product is designed for fuel-injected, automatic transmission vehicles only.Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.
Thank also this part
Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle switch
to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either in PARK or
NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input MUST rest at ground
in order for the remote start system to operate. Connected properly the vehicle will only start while in PARK or NEUTRAL.
In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock-out that will not allow the
starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure B.
Connect the other wire from the toggle switch to chassis ground.
Do i just ground this wire and call it a day?
From guys that did this install on AT can you please point me on the right track
thank you
CTScottThread starterUSA, CT · Nov 10, 2014#208 Originally Posted by
camry09 ↑ Alright maybe im missing something, but so far this is the only thing that ive found
IMPORTANT! This product is designed for fuel-injected, automatic transmission vehicles only.Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.
Thank also this part
Connect this wire to the toggle (override) switch as shown in Figure A. Connect the other wire from the toggle switch
to the PARK/NEUTRAL switch in the vehicle. This wire will test with ground with the gear selector either in PARK or
NEUTRAL. This will prevent the vehicle from accidentally being started while in a drive gear. This input MUST rest at ground
in order for the remote start system to operate. Connected properly the vehicle will only start while in PARK or NEUTRAL.
In some vehicles, the PARK/NEUTRAL position switch activates a factory starter lock-out that will not allow the
starter to operate in a drive gear. In these vehicles, connect this wire to the toggle switch as shown in Figure B.
Connect the other wire from the toggle switch to chassis ground.
Do i just ground this wire and call it a day?
From guys that did this install on AT can you please point me on the right track
thank you
Looking at the configuration guide where you can get into the menus and change different settings, it looks like this one does not have a setting for it. I just installed a Viper remote starter (also made by DEI, like Valet) in my sister's Tacoma and had the same issue, but changing the default MT setting to AT solved it.
For yours, just ground that wire.
camry09Allentown PA · Dec 20, 2014#209Success!!!!! its alive and working, 3x time hit Close and it starts up
The only thing it doesn't want to open from Remove while vehicle is running, will have to use the key to open the doors for now till can figure that out
A special thank you to STScott for helping with advice
JBincMI, USA · Mar 29, 2015#210I've go an interesting issue. 2007 Yaris sedan, no factory alarm, no engine immobilizer, power locks. I followed the DIY PDF to install U1272 Ultra Start. Had remote lock/unlock functionality with park lamp flash using either of the two fobs, but remote start did not work when I pressed the star button and the horn did not sound with any command. The strange things is that it would remote start intermittently when I pressed the star button, then lock button.
I entered programming mode and was working through the lock button menus when the car suddenly started but never disengaged the starter 😲. I tried pressing the brake then turning the key to OFF (normal to stop remote start functionality), but that didn't work. After some panic, I pulled power to the remote start module. Now every time I apply power to the module, the vehicle instantly cranks, but won't start. I have the hood up (hood switch open) and key is out of ignition--doesn't matter. Continuity is good on the black starter wire to yellow wire from remote starter module. None of the wires of the 6 pin remote starter connector are shorted to ground (continuity checked). Is there somewhere I can check to see if the module could be giving ground when it shouldn't. Please help!
JBincMI, USA · Mar 29, 2015#211One other note--now when I plug in the connector on the remote starter side for door lock/unlock my lock button on the door switch panel does not work, but unlock does. If I disconnect the connector again, the lock and unlock work when using the door switch panel (normal functionality).
CTScottThread starterUSA, CT · Mar 29, 2015#212 Originally Posted by
JBinc ↑ I've go an interesting issue. 2007 Yaris sedan, no factory alarm, no engine immobilizer, power locks. I followed the DIY PDF to install 1172 Ultra Start. Had remote lock/unlock functionality with park lamp flash using either of the two fobs, but remote start did not work when I pressed the star button and the horn did not sound with any command. The strange things is that it would remote start intermittently when I pressed the star button, then lock button.
I entered programming mode and was working through the lock button menus when the car suddenly started but never disengaged the starter 😲. I tried pressing the brake then turning the key to OFF (normal to stop remote start functionality), but that didn't work. After some panic, I pulled power to the remote start module. Now every time I apply power to the module, the vehicle instantly cranks, but won't start. I have the hood up (hood switch open) and key is out of ignition--doesn't matter. Continuity is good on the black starter wire to yellow wire from remote starter module. None of the wires of the 6 pin remote starter connector are shorted to ground (continuity checked). Is there somewhere I can check to see if the module could be giving ground when it shouldn't. Please help!
It sounds like the relay for the starter is stuck closed. Try giving the remote start unit a good hard slap with your hand to see if it will unstick. Even if it does, I would not trust it and would get it replaced. I recently went through two bad units before getting a good one, with a Viper remote starter that I installed for a friend.
JBincMI, USA · Mar 30, 2015#213 Originally Posted by
CTScott ↑ It sounds like the relay for the starter is stuck closed. Try giving the remote start unit a good hard slap with your hand to see if it will unstick. Even if it does, I would not trust it and would get it replaced. I recently went through two bad units before getting a good one, with a Viper remote starter that I installed for a friend.
I gave it a few solid slaps this morning. No luck. I'll contact Ultra Starters and see if they will warranty it. Have you had luck with the manufacturer replacing the unit under warranty in this scenario?
CTScottThread starterUSA, CT · Mar 30, 2015#214I haven't had one of theirs fail. They theoretically only sell to authorized installers, so you will likely have to deal with who you bought it from.
JBincMI, USA · Mar 30, 2015#215I spoke to the seller--fairly simple. They're sending a replacement module. Thanks for your help thus far.
pennyracergrants pass · Aug 14, 2015#216hi CTScott you have giving me some info in the past of a few different topics my only trouble i have had for years on my 08 yaris lb with power package is when my car is stored in a building for months at a time even with a trickle charger hooked up my battery will drain completely i have a python 571xp remotoe start with keyless entry i have pulled all my fuses for the stereo and amps trying to isolate this constant draw did not help then sometimes the cars will be stored same way battery stays up i keep telling my stereo guy its not the car itself but im sure wondering these days i have used yellow top optima and oddessy battery for longer life still not holding out when stored i do run a 180 amp dc alternator had the problem before and after alt install what do you think would cause this draw to be there most of the time and others not ? any advise from you would be awsome you are the yarisworld info king here oh no others add ons installed on my yaris just a little radio work and remote start and keyless entry only
CTScottThread starterUSA, CT · Aug 14, 2015#217 Originally Posted by
pennyracer ↑ hi CTScott you have giving me some info in the past of a few different topics my only trouble i have had for years on my 08 yaris lb with power package is when my car is stored in a building for months at a time even with a trickle charger hooked up my battery will drain completely i have a python 571xp remotoe start with keyless entry i have pulled all my fuses for the stereo and amps trying to isolate this constant draw did not help then sometimes the cars will be stored same way battery stays up i keep telling my stereo guy its not the car itself but im sure wondering these days i have used yellow top optima and oddessy battery for longer life still not holding out when stored i do run a 180 amp dc alternator had the problem before and after alt install what do you think would cause this draw to be there most of the time and others not ? any advise from you would be awsome you are the yarisworld info king here oh no others add ons installed on my yaris just a little radio work and remote start and keyless entry only
The Yaris has one of the highest static draws that I have ever seen on a car (~100 mA), which by itself will drain a battery is less than a month. Add a remote starter and you are up in the 200-250 mA range, where 2 weeks without starting it is pushing it. Your trickle charger may just not be enough to counteract the static draw. I use a battery quick disconnect switch on Crashy.
pennyracergrants pass · Aug 14, 2015#218okay is there a way if i have a professional wire my new alarm with remote start to have a remote function on a relay to kill the remote start draw when i store the car to slow the draw down i like the idea of a battery isolator just have to re program the head unit after each time i get my car out of storage to drive i am in the process of adding a second or even a third battery to build up the battery reserve for the radio and crazy voltage draw they will be mounted in the rear behind back seat quarters panels have you seen my new a pillar speaker addition still have to get the grills installed for the complete stealth look Picture lost · i214.photobucket.com
Picture lost · i214.photobucket.com
pennyracergrants pass · Aug 14, 2015#219one more question ctscott what brand would you spend your money on for complete security , remote start and gps tracking ? seems my only two options these days are viper or CompuStar ? sorry to be off topic here
CTScottThread starterUSA, CT · Aug 14, 2015#220No. The receiver for the remote is what creates the extra drain.
Nice speaker install on the pillars!
Tanes70Massachusetts · Sep 26, 2015#221Hi, I'm trying to install a remote starter on 2010 Toyota Yaris with immobilizer. I Use your guide to find all the wires and was easy to connect everything, but the starter didn't work... I'm a little confused with this car because I don't know if it has an alarm system or not. It has power doors and panic bottom on the key. I made the following connections between the remote starter module and the car: Ignition 1 on remote starter to the green wire in the car, Ignition 2 to the pink cable on the car, Accessory to the white one, and the Start to the black wire. I connect the bypass module as directed and it seems to be ok. Brake, parking lights, tach signal, horn and hood safety switch, were connected according with your wiring guide. So I have some doubts on the Ignition cables (should I use the green cable as ignition 2 and the pink one as ignition 1?) and should I use the alarm disarm wire on the module? If yes where must be connect it?
Thanks any help would be appreciated.
Sincerely, Andres.
CTScottThread starterUSA, CT · Sep 27, 2015#222 Originally Posted by
Tanes70 ↑ Hi, I'm trying to install a remote starter on 2010 Toyota Yaris with immobilizer. I Use your guide to find all the wires and was easy to connect everything, but the starter didn't work... I'm a little confused with this car because I don't know if it has an alarm system or not. It has power doors and panic bottom on the key. I made the following connections between the remote starter module and the car: Ignition 1 on remote starter to the green wire in the car, Ignition 2 to the pink cable on the car, Accessory to the white one, and the Start to the black wire. I connect the bypass module as directed and it seems to be ok. Brake, parking lights, tach signal, horn and hood safety switch, were connected according with your wiring guide. So I have some doubts on the Ignition cables (should I use the green cable as ignition 2 and the pink one as ignition 1?) and should I use the alarm disarm wire on the module? If yes where must be connect it?
Thanks any help would be appreciated.
Sincerely, Andres.
I have installed three myself based on my guide. Did you install a transponder key bypass module, as one will be necessary on any 09+ due to the immobilizer.
Tanes70Massachusetts · Sep 27, 2015#223 Originally Posted by
CTScott ↑ OK. The TVIP OEM Alarm has a 36 pin connector:
Attachment 31700
Pin 12 (white/light blue wire) goes to a starter cut relay, so you will need to follow that wire to the starter cut relay, and tap the Black Wire coming off of that relay with your start wire. On a non-alarm car that would be the black wires on the ignition switch connector.
Pin 9 (orange wire) is the ignition switch power input to the TVIP, so if it actually needs the (+) IGNITION OUT (TO ALARM) connection, that's where it would be done.
The key sense wire is the yellow wire on the two pin connector that is near the face of the keyswitch.
Where is this connector located?
Tanes70Massachusetts · Sep 27, 2015#224 Originally Posted by
CTScott ↑ I have installed three myself based on my guide. Did you install a transponder key bypass module, as one will be necessary on any 09+ due to the immobilizer.
Yes, I installed the bypass module, and it's all set. I was reading in this forum and realized that I connect the start wire to the black wire on the starter harness so probably that's the problem, so I have to find the TVIP OEM Alarm connector which I don't know where is located at, and connect the start wire on Pin #12... Also how I know if I should connect the (+) Ignition Output to the pin 9 on the TVIP OEM Alarm connector?
Thanks again for your quick response.
CTScottThread starterUSA, CT · Sep 27, 2015#225 Originally Posted by
Tanes70 ↑ Yes, I installed the bypass module, and it's all set. I was reading in this forum and realized that I connect the start wire to the black wire on the starter harness so probably that's the problem, so I have to find the TVIP OEM Alarm connector which I don't know where is located at, and connect the start wire on Pin #12... Also how I know if I should connect the (+) Ignition Output to the pin 9 on the TVIP OEM Alarm connector?
Thanks again for your quick response.
The TVIP module should be to the right behind the glove box. I haven't done one with the TVIP system, but it does intercept the starter signal. I am not sure if the car will start if you bypass that connection, or if you will make the alarm trigger when you do so. You really have to disarm the TVIP before starting.
thomascubaEdmonton · Nov 9, 2015#226Dear CTScott;
I have successfully installed a 2 Way - RadioStart remote starter on a 2007 5 door HB automatic w/o inmobilizer. It does locks and unlocks the doors and starts the car.
I do still have more than 17 cables to connect. That's why I need your help on finding them and if possible pictures of their location and colors.
In theory as it is right now you can drive away when the car is started via remote, so I need to connect more inputs to ensure safety since the car will be driven by my wife.
Questions:
1- Are the two green wires on top of the break switch a +12V signal when break is depressed? Conn A13 Pin 1 as per your DIY manual (very hard to measure voltage due to accessibility)
2- Is there any unique cable that goes to ground when any door is opened or that goes to 12V when any door is opened?
3- Ignition Input of Key Cylinder (+) Ignition wire that provides +12V when Ignition is on and while cranking the starter. Green Conn 8 Pin 1. There is already a cable from the started connected to this one. Should I tap the input to the remote to the same cable?
4- If I inject ground to Conn D4 pin 13 white wire or inject +12V to Conn 4 Pin 29 Green will either action turn on the same lights (Parking Lights)?
5- Are the Parking lights the same as Hazard lights and turning lights?
Thanks!
tmontagueCaledonia Ont. · Dec 26, 2015#227Alright I took some time and sat down and read through the installation manual to get the install ready for tomorrow. since Dan's DIY is no longer available on line (if anyone has it please let me know) I have a few Q's regarding the wiring. I am installing just a keyless entry (viper 211hv)
1. For the dome light output coming from the viper harness, what wire do I tap into on the 4k connector? I looked at the Toyota wiring diagram and from my understanding it would be the pink wire. I'm still learning how to read the diagrams so it'd be great if someone with experience can confirm this for me. I know the dome light input goes to a ground so that one is easy.
2. In CTScotts guide at the very bottom for the keyless entry part it shows "transponder key bypass module connections" Do I need to tap into these just for a keyless entry (no remote start or alarm)? My understanding was I only need to connect the Viper Modules yellow wire to ignition so that I could get the locks to unlock when the ignition is off.
3. Where do I connect the viper blue wire "second unlock output" so that I have progressive unlocking? From my research my understanding is to connect it to the brown doors lock wire, is this correct?
4. Do I need to bother with any of the other wires that go to the ignition such as "unlock 87a normally closed" if all I want is for the ignition to unlock the locks when turned off? Or is just the yellow viper wire connected to 12v ignition adequate enough?
Thanks guys
tmontagueCaledonia Ont. · Dec 26, 2015#228Got in all wired up. Unlock/lock works, dome light goes on for 1minute when unlocked.
However there is no horn when locked or when panic is pressed. I can hear the relay in the viper module trying to signal for the horn but nothing happens.
My horn works fine if I press the steering wheel.
Also my parking lights do not flash either. Any ideas on what I should be checking?
tmontagueCaledonia Ont. · Dec 26, 2015#229Just tried to start the car. As soon as key goes to start a click is heard and all power dies. Only way to get power back on is to disconnect , battery and then the same thing will happen again.
Here is a summary of what wires I connected to what:
H1/1 Red- connected to male bottom terminal in under dash fuse panel (the viper module is receiving power) so this wire is good
H1/2 blue- not connected
H1/3 black/white- connected to ground (works as dome light turn on/off w/ keyless unlock)
H1/4 black/white -connected to pink wire in 4K connected in underdash panel (works as dome light turns on/off with keyless unlock)
H1/5 green/black -connected to brown lock wire on CTScotts guide (works because the keyless fob locks the doors)
H1/6 white/black- not connected
H1/7 violoet/black- connected to ground (works because lock function works on fob
H1/8 blue/black- connected to green unlock wire on CTScotts guide (works because unlock function works on fob)
H1/9 violet- connected to ground
H1/10 white- connected to parking light (-)flask white wire in CTScott's guide on the headlight switch connector
H1/11 black- connected to ground
H1/12 brown - connected to black horn wire in CTScott's guide
H1/13 -not connected
H1/14 -not connected
H1/15 Yellow- connected to the white ignition accessory wire in CTScott's guide (I disconnected it and the car still shuts off all power when you try and start it as I thought maybe this wire was the culprit)
H1/16 -not connected
H1/17 -not connected
H1/16 - not connected
only have the lock and unlock function working as well as the dome light (goes on for 1 min when car is unlocked using fob)
parking lights do not flash and horn doesn't beep when locked 2x. Horn works when pressing the steering wheel button.
When panic is pushed I can hear the relay in the viper module trying to set off the horns but the relay under the hood isn't triggered.
When the car is turned to start a click is heard and all power is shut off from the car. It stays this way until the ecu is reset by unplugging the negative battery terminal. This seems to be an immobilizer issue that is doing this.
If anyone sees an issue with my wiring or sees that I wired to a wrong wire please let me know. I'm out of town for a few days but am hoping to have the car up and running when I get back.
Any help is appreciated...
CTScottThread starterUSA, CT · Dec 26, 2015#230 Originally Posted by
tmontague ↑ Alright I took some time and sat down and read through the installation manual to get the install ready for tomorrow. since Dan's DIY is no longer available on line (if anyone has it please let me know) I have a few Q's regarding the wiring. I am installing just a keyless entry (viper 211hv)
1. For the dome light output coming from the viper harness, what wire do I tap into on the 4k connector? I looked at the Toyota wiring diagram and from my understanding it would be the pink wire. I'm still learning how to read the diagrams so it'd be great if someone with experience can confirm this for me. I know the dome light input goes to a ground so that one is easy.
2. In CTScotts guide at the very bottom for the keyless entry part it shows "transponder key bypass module connections" Do I need to tap into these just for a keyless entry (no remote start or alarm)? My understanding was I only need to connect the Viper Modules yellow wire to ignition so that I could get the locks to unlock when the ignition is off.
3. Where do I connect the viper blue wire "second unlock output" so that I have progressive unlocking? From my research my understanding is to connect it to the brown doors lock wire, is this correct?
4. Do I need to bother with any of the other wires that go to the ignition such as "unlock 87a normally closed" if all I want is for the ignition to unlock the locks when turned off? Or is just the yellow viper wire connected to 12v ignition adequate enough?
Thanks guys
1. Dome light is the pink wire of the three wires in the connector to the lower left on page 3 (labeled: power connection)
2. For keyless entry you do not need the transponder key bypass module (or the connections for it)
3. For progressive unlocking you don't need a second output - You just have to pulse the unlock wire twice with the keyless entry system (if it supports that function. If not, you would connect the second output to the same wire as the first output).
4. I would need to see the book for the unit to verify, but unlock on ignition off should not require anything more than sensing the ignition losing power.
CTScottThread starterUSA, CT · Dec 26, 2015#231 Originally Posted by
tmontague ↑ Got in all wired up. Unlock/lock works, dome light goes on for 1minute when unlocked.
However there is no horn when locked or when panic is pressed. I can hear the relay in the viper module trying to signal for the horn but nothing happens.
My horn works fine if I press the steering wheel.
Also my parking lights do not flash either. Any ideas on what I should be checking?
I just looked at my document (which I haven't looked at in a couple of years) and I show the wring connector for the horn. It should be the white connector, which just has the single black wire in it (no other wires for an 06-08) or the black and a brown and blue for 09-11.
For the parking light flash, are you using the + or - flash?
CTScottThread starterUSA, CT · Dec 26, 2015#232 Originally Posted by
tmontague ↑ Just tried to start the car. As soon as key goes to start a click is heard and all power dies. Only way to get power back on is to disconnect , battery and then the same thing will happen again.
Here is a summary of what wires I connected to what:
H1/1 Red- connected to male bottom terminal in under dash fuse panel (the viper module is receiving power) so this wire is good
Correct
H1/2 blue- not connected
Correct
H1/3 black/white- connected to ground (works as dome light turn on/off w/ keyless unlock)
Correct
H1/4 black/white -connected to pink wire in 4K connected in underdash panel (works as dome light turns on/off with keyless unlock)
Correct
H1/5 green/black -connected to brown lock wire on CTScotts guide (works because the keyless fob locks the doors)
Correct
H1/6 white/black- not connected
Correct
H1/7 violoet/black- connected to ground (works because lock function works on fob
Correct
H1/8 blue/black- connected to green unlock wire on CTScotts guide (works because unlock function works on fob)
Correct
H1/9 violet- connected to ground
Correct
H1/10 white- connected to parking light (-)flask white wire in CTScott's guide on the headlight switch connector
Correct if the wire in pin 10 (4th from the right in that same row) is white/black. If it is green, then you have to use the + parking light flash
H1/11 black- connected to ground
Correct
H1/12 brown - connected to black horn wire in CTScott's guide
See my note in my response above about the correct connector
H1/13 -not connected
Correct
H1/14 -not connected
Correct
H1/15 Yellow- connected to the white ignition accessory wire in CTScott's guide (I disconnected it and the car still shuts off all power when you try and start it as I thought maybe this wire was the culprit)
Incorrect - This is an ignition input to the keyless entry system that has to stay hot even during cranking. This should be connected to the pink wire on the ignition switch connector, not the white accessory wire, which drops when cranking
H1/16 -not connected
Correct
H1/17 -not connected
Correct
H1/16 - not connected
Correct
only have the lock and unlock function working as well as the dome light (goes on for 1 min when car is unlocked using fob)
parking lights do not flash and horn doesn't beep when locked 2x. Horn works when pressing the steering wheel button.
When panic is pushed I can hear the relay in the viper module trying to set off the horns but the relay under the hood isn't triggered.
When the car is turned to start a click is heard and all power is shut off from the car. It stays this way until the ecu is reset by unplugging the negative battery terminal. This seems to be an immobilizer issue that is doing this.
If anyone sees an issue with my wiring or sees that I wired to a wrong wire please let me know. I'm out of town for a few days but am hoping to have the car up and running when I get back.
Any help is appreciated...
See my comments above in red.
tmontagueCaledonia Ont. · Dec 26, 2015#233thanks CTScott for taking the time to answer my Q's. I understand where I made the mistakes now.
Can you explain to me what you mean about the horn wire? If it turns out that I have the connector that needs a + parking light pulse than what does that mean for my horn connection? What other wire would there be to tap into the horn and what determines if I need to use a different wire?
Can I tap into the green ignition wire instead of the pink? Both are 12v ignition and the thicker gauge of the green makes it easier to tap with my t taps due to their sizing
I'm curious as to what caused the immobilizer to shut everything down, obviously a wrong wire I tapped into but what specifically causes this? It happened when I installed my HID's as well until I put on a proper functioning ballast (the original one was defective)
Thanks
CTScottThread starterUSA, CT · Dec 26, 2015#234 Originally Posted by
tmontague ↑ thanks CTScott for taking the time to answer my Q's. I understand where I made the mistakes now.
Can you explain to me what you mean about the horn wire? If it turns out that I have the connector that needs a + parking light pulse than what does that mean for my horn connection? What other wire would there be to tap into the horn and what determines if I need to use a different wire?
For the horn wire, the picture I included was the incorrect picture. The correct connector is the one on the left in the picture below. The horn is a ground to honk wire (i.e. -).
Can I tap into the green ignition wire instead of the pink? Both are 12v ignition and the thicker gauge of the green makes it easier to tap with my t taps due to their sizing
Yes - The green would be fine as well.
I'm curious as to what caused the immobilizer to shut everything down, obviously a wrong wire I tapped into but what specifically causes this? It happened when I installed my HID's as well until I put on a proper functioning ballast (the original one was defective)
I am not sure, as the immobilizer only prevents starting - It can not kill the running engine.
Thanks
...
tmontagueCaledonia Ont. · Dec 26, 2015#235Great, thanks
I'm assuming the black wire is the horn wire on the connector you were talking about?
As for the immobilizer is makes a sound like a fuse blowing or something and instantly all power is gone as if the battery is disconnected. The car actually never starts cranking because as soon as you turn the key power goes off. The only thing that allows power again is to disconnect the battery for a few seconds and then it's back.
CTScottThread starterUSA, CT · Dec 26, 2015#236 Originally Posted by
tmontague ↑ Great, thanks
I'm assuming the black wire is the horn wire on the connector you were talking about?
As for the immobilizer is makes a sound like a fuse blowing or something and instantly all power is gone as if the battery is disconnected. The car actually never starts cranking because as soon as you turn the key power goes off. The only thing that allows power again is to disconnect the battery for a few seconds and then it's back.
Correct on the black wire.
The second part is definitely wrong and is definitely not the immobilizer.
tmontagueCaledonia Ont. · Dec 26, 2015#237I just saw your post above about the horn connector, I missed it earlier.
I think it has something to do with too much power going to the ecu and it shutting d power to not incur any damage.
I just checked all my wires. My ignition and my horn were wired wrong. My parking light one was correct on the white (-) wire as I don't have the green wire it is white/black. Not sure as to why the parking lights aren't triggered. I will check the tap as my taps are rated for slightly bigger wires so it takes a little extra time to ensure proper connection.
When I'm back in town in a few days i'll re tap the incorrect wires and purchase some smaller t taps. Hopefully that'll fix the issue.
I recently wired in superspeed horns that must have a lose connector or ground somewhere as they sometimes work and are as of right now not working. The relay clicks so I can tell if the viper is triggering it or not. I'll have to remove the bumper and look at the horn connections once everything is done.
tmontagueCaledonia Ont. · Dec 30, 2015#238Just reconnected the 3 wires properly horn now works with the second press of the lock. However my parking lights still are not blinking.
The parking lights do work when switched on, but the key fob does not trigger them to blink. I checked the t taps and they have tapped into the wires properly.
Am I able to tap into the turn signals instead instead the the lights? I'd like to try that since the parking light wires don't seem to be triggering the lights.
Any ideas?
CTScottThread starterUSA, CT · Dec 30, 2015#239 Originally Posted by
tmontague ↑ Just reconnected the 3 wires properly horn now works with the second press of the lock. However my parking lights still are not blinking.
The parking lights do work when switched on, but the key fob does not trigger them to blink. I checked the t taps and they have tapped into the wires properly.
Am I able to tap into the turn signals instead instead the the lights? I'd like to try that since the parking light wires don't seem to be triggering the lights.
Any ideas?
Verify that your remote starter is pulling the white wire to ground to flash them. You can do a quick test by simply jumping from the white to one of the white/black wires by sticking a piece of wire into the back of the connector.
tmontagueCaledonia Ont. · Dec 30, 2015#240I'll be looking at it again tomorrow.
So if I take a wire like say a paperclip and stick it into the back of the module connector to connect the white wire to a white/black (ground) wire I should see the parking lights switch on correct? I just want to clarify before I go about troubleshooting it tomorrow
Fwiw, the power shut off during start up was due to my not tightening the negative terminal when trying to start it. This caused no issue during light power load but during heav load such as the starter it caused a short and powered everything off.
Same issue is seen with the corroded negative terminal or wire.
CTScottThread starterUSA, CT · Dec 30, 2015#241 Originally Posted by
tmontague ↑ I'll be looking at it again tomorrow.
So if I take a wire like say a paperclip and stick it into the back of the module connector to connect the white wire to a white/black (ground) wire I should see the parking lights switch on correct? I just want to clarify before I go about troubleshooting it tomorrow
Fwiw, the power shut off during start up was due to my not tightening the negative terminal when trying to start it. This caused no issue during light power load but during heav load such as the starter it caused a short and powered everything off.
Same issue is seen with the corroded negative terminal or wire.
Correct.
That makes sense on the power-off.
tmontagueCaledonia Ont. · Dec 31, 2015#242I disconnected the white connector from the module and stuck a paper clip in the H1/10 and the H1/3 which is a ground for the dome light. Sure enough the parking lights (front and rear) went on.
So I'm assuming that this means that my wiring and taps are obviously fine but there is an issue with the viper module not grounding the parking lights? I'm going to read the instructions and see if I only need a new module that I can then program my fob's to or if that is not possible and I need a module with new fob's as well.
Any other possibilities or things that I could do to fix this? I'm hoping the ebay seller will send me a module free of charge but if this is something that I can fix fairly easy myself to get the module to ground properly then I'd rather just do it myself and save waiting for a new module.
CTScott do you know of a way to fix the module to properly ground?
CTScottThread starterUSA, CT · Dec 31, 2015#243 Originally Posted by
tmontague ↑ I disconnected the white connector from the module and stuck a paper clip in the H1/10 and the H1/3 which is a ground for the dome light. Sure enough the parking lights (front and rear) went on.
So I'm assuming that this means that my wiring and taps are obviously fine but there is an issue with the viper module not grounding the parking lights? I'm going to read the instructions and see if I only need a new module that I can then program my fob's to or if that is not possible and I need a module with new fob's as well.
Any other possibilities or things that I could do to fix this? I'm hoping the ebay seller will send me a module free of charge but if this is something that I can fix fairly easy myself to get the module to ground properly then I'd rather just do it myself and save waiting for a new module.
CTScott do you know of a way to fix the module to properly ground?
Viper's quality has seriously gone down hill (in my opinion). I installed a Viper 2 way system last year for my sister and it took three units before everything worked.
tmontagueCaledonia Ont. · Dec 31, 2015#244Wow, that's pretty brutal. I just heard back from the seller and he is sending me a whole unit free of charge.
The only down side is the long drive to the border to pick it up. Fingers crossed that everything works okay and it is fully functional.
I plan on making a diy for the keyless entry with some of the info you posted if you're okay with that?
I just figured it's easier for others if all the info is piled in one post versus a fe different sources.
tmontagueCaledonia Ont. · Jan 5, 2016#245*EDIT*
Just solved the problem. I somehow missed the small note in the instructions to move the light flash jumper (15A fuse in the module) to the other position. I caught on to this when I dissected the old module and noticed that the connectors on the motherboard from the parking light flash led to that fuse. Something so simple. I'll add it to my DIY
Just received my new module that was sent to me after wasting 3 hrs driving to the border to get it.
It also has the same problem with not grounding the parking lights. I re checked my wiring by jumping it to a negative and the parking lights go on.
CTScott do you have any ideas before I email the seller and rip him a new one for sending me 2 defective modules and wasting my time?
Is it possible that I need to connect to the positive wire for the parking lights as the module is not meant to ground but to supply power?
I just took a look at the module and there are 3 female prongs ofr the 15A fuse that is in the module. Meaning that it has 2 positions that the fuse can be in. I took apart my old module and I'm wondering if I should move the fuse on the module and see if that fixes it?
maral01Quebec, Canada · Oct 25, 2016#246Hi everyone,
Got a bit of a remote starter mystery here. I have just installed a Viper 5501 2 way remote start system in my 2009 Yaris hb. Alongside, I installed a Fortin EVO-ALL bypass module. My car is a manual and the "brain" haa been programmed accordingly. I've also connected a relay as a bypass for the clutch (bypass activated when the remote starter engages).
Here is the problem: I successfully do the MTS procedure prior to exiting the car and no issues, the vehicle remains on until I shut it off with the remote. When I go to start it back up, all it does is crank the starter but the engine won't start. I tried unplugging the immobilizer bypass module and leaving the key in the ignition to remote start it but no success. I doubled, even triple checked all connections and everything is fine. I also checked all my heavy gauge wires to ensure that all of them had voltage during the startup sequence and I confirmed that everything is fine there.
Has anyone else experienced this kind of issue before? I am really scratching my head on this one....
Update @ 2130hrs: The vehicle will start when I put the key at the "on" position after I pressed on the remote starter button.... If I just leave the key at the off position while trying to remote start, the starter will still crank only, can't get the engine to fire up. Almost sure it must be something with the heavy gauge wiring.... Any ideas?
govtecPhila, PA · Sep 19, 2017#247Hey guys,
I just finished wiring up Clifford 4105x remote start with door lock/unlock in an automatic 07 Hatch with power doors/windows and no immobilizer. Only the door lock/unlock responds to the clifford remote. I can't seem to get remote start/horn/parking lights to work. Any advice?...I wired the system as per the wiring diagram posted by CTScott. I also did the tach learning steps after the installation.
Thanks
mr_robotNYC · Jan 3, 2018#248You don't need to hook it up to the HVAC at all.
Connecting the parking lights is optional, it's just too give you visual confirmation.
The bypass module should handle the ignition and all.
Sent from my iPhone using Tapatalk Pro
mr_robotNYC · Jan 3, 2018#249Yes the Yaris has ignition 1 & 2 respectively.
Sent from my iPhone using Tapatalk Pro
AethelflaedCanada · Mar 28, 2021#250 Originally Posted by
CTScott ↑ I have been getting a lot of questions lately regarding installing remote start on a Yaris, so today I put together a wiring guide for those interested.
Attachment 30944
Hi guys I'm trying to download the instructions but I think the link is dead. Can someone please post a new download link?