Replies continued
yarisyetiLouisiana · Jan 24, 2012#151CTScottThread starterUSA, CT · Jan 24, 2012#152 Originally Posted by
yarisyeti ↑
For the remote window closure you need an auto window closer device, like the DEI 530T. The aux output of the remote starter would become an input to the 530T to tell it to crank up the windows (or with another output, down as well for airing it out in the hot weather).
yarisyetiLouisiana · Jan 24, 2012#153could I use a 529T?
yarisyetiLouisiana · Jan 24, 2012#154Can I use a 529T?
CTScottThread starterUSA, CT · Jan 24, 2012#155 Originally Posted by
yarisyeti ↑ Can I use a 529T?
Yes. The 529T just gives you one direction, whereas the 530T gives you both.
yarisyetiLouisiana · Jan 25, 2012#156wouldn't hooking up a relay like thishttp://www.automotiverewire.com/Navagation/spdtrelayswindows.htm work just the same?
CTScottThread starterUSA, CT · Jan 25, 2012#157 Originally Posted by
yarisyeti ↑ wouldn't hooking up a relay like thishttp://www.automotiverewire.com/Navagation/spdtrelayswindows.htm work just the same?
Yes, although the relays will stay energized as long as the output channel is on, whereas the 529T or 530T has some intelligence to turn its relays off. The problem with leaving them energized is that if you trigger the output channel after turning the car off, and then leave the car parked for a day or so, you may come back to a dead battery.
mirapatecGeorgia, U.S.A. · Jan 24, 2013#158@ CTScott - Thanks for sharing all this information with other Yaris owners.
CTScottThread starterUSA, CT · Feb 8, 2013#159 Originally Posted by pat005 ↑
Sorry to be "that guy" but I seem to be struggling with something I feel isn't very complicated but don't want to mess it up. Here's mine
Picture lost · plus.google.com but I can't find
Picture lost · plus.google.com from the DIY I can't seem to find anything that looks remotely similar with the two black and two pick wires. Oh yeah, 2008 HB Yaris. Thanks
https://plus.google.com/photos/11558...66988681874529 Link to the two photos
You are about a foot to the left of where that connector in my picture is. It is the ignition switch connector, which is located at the base of the ignition switch, on the right side of the steering column.
WestCoastDawson Creek · Jul 20, 2013#160Thank you so much CTScott,
My 2007 auto transmission Yaris is a 5 door hatch back without keyless entry, manual windows, but have a button to lock and unlock the door. Does it need a keypass or not?
Thank you again,
CTScottThread starterUSA, CT · Jul 20, 2013#161 Originally Posted by
WestCoast ↑ Thank you so much CTScott,
My 2007 auto transmission Yaris is a 5 door hatch back without keyless entry, manual windows, but have a button to lock and unlock the door. Does it need a keypass or not?
Thank you again,
Most likely not with an 07, but you can tell by looking at the ignition switch. If it is all metal then no, if the part that rotates is metal and the part that surrounds it is black plastic, then yes.
WestCoastDawson Creek · Jul 21, 2013#162Thank you so much for your reply so quickly. My ignition switch doesn't have the black plastic surround it. So should be don't need the keypass.
My remote starter is Firstech CM6200. I connected the CN1(Accessory, Starter, Ignition, Ground, Constant 12V, 12 Parklning light output), and CN4(Unlock Output, Lock Output).
But didn't connect the CN2, which are (Output to Starter-kill), Hood Pin Input, .... etc.)
Because I don't know where to find these cables in your diy chart. Any advices for me?
WestCoastDawson Creek · Jul 21, 2013#163Actually, my CN2 details as below:
(-) 250mA Output to Starter-Kill Blue 1
(-) Parking Light Reminder Orange/Black 2
(-) 250mA 2nd Parking Light Output(POC #1) Green/White 3
(-) Emergency Brake Input Light Blue 4
(-) 250mA 2nd Starter Output (POC #2) Red/Black 5
(+) Foot Brake Input Light Blue/White 6
(-) 250mA 2nd Ignition Output (POC #3) Green 7
(-) Trunk Trigger Input Violet/Black 8
(-) 250mA 2nd Accessory Output (POC #4) White/Black 9
(+/-) Door Trigger Input Red/White 10
(-) 250mA Status Out(GWR) (POC #5) Black 11
(+/-) Key Sense/Glow Plug Input Brown/White 12
(-) 250mA Rearm Output (POC #6) Orange 13
(-) Slave/Timer Start input Pink 14
(-) 250mA Disarm Output (POC #7) Orange/White 15
Engine Sensing Input (Alt./Tach/Battery) Yellow/Black 16
(-) 250mA Horn Output (POC #8) White 17
(-) Hood Pin Input Gray/Black 18
(-) 250mA Aux1 Output (POC #9) Violet 19
(+) 12V Output to Siren Brown 20
I only need remote start my car, and remote lock and unlock my car, do I need connect all of these cables or just some of them. It's really hard for me to find the right connecting place.
CTScottThread starterUSA, CT · Jul 21, 2013#164Starter kill is an optional one that requires an extra relay and is documented in your remote starter's manual. You end up cutting the black starter wires on the ignition switch connector and connecting the relay in between.
Parking light output, foot brake, 2nd Ignition output, and Tach input are all in my guide.
The hood pin will be documented in your manual, as it is simply a pin switch that requires you to drill a hole to mount under the hood. It doesn't get connected to any of the car's wires.
WestCoastDawson Creek · Jul 21, 2013#165Hi CTScott, I have tested my +12V parking light(green pin 29), but the meter read is 0, and the -12V parking light(white pin 13) is 12V. What I can do?
My CM6200 need input is +12V.
Thanks in advance,
CTScottThread starterUSA, CT · Jul 21, 2013#166 Originally Posted by
WestCoast ↑ Hi CTScott, I have tested my +12V parking light(green pin 29), but the meter read is 0, and the -12V parking light(white pin 13) is 12V. What I can do?
My CM6200 need input is +12V.
Thanks in advance,
Parking light is not an input, it is an output, so your device will output +12V to pin 29 to flash the lights.
WestCoastDawson Creek · Jul 22, 2013#167Good to know, and where is the Emergency Brake pin in my 2007 auto transmission yaris?
CTScottThread starterUSA, CT · Jul 22, 2013#168 Originally Posted by
WestCoast ↑ Good to know, and where is the Emergency Brake pin in my 2007 auto transmission yaris?
The yellow wire at the base of the ebrake lever or the yellow wire in pin 4C-2. The ebrake is typically not required for remote starters, except for with manual trans.
WestCoastDawson Creek · Jul 22, 2013#169Do my auto trans car still don't need the Door Trigger input for my remote start?
CTScottThread starterUSA, CT · Jul 22, 2013#170 Originally Posted by
WestCoast ↑ Do my auto trans car still don't need the Door Trigger input for my remote start?
Check the manual for your remote starter. Most do not require that, as they can be used with cars with manual locks.
WestCoastDawson Creek · Jul 22, 2013#171Where to output my (+) 12V Siren if i my car don't have the arm system?
CTScottThread starterUSA, CT · Jul 22, 2013#172 Originally Posted by
WestCoast ↑ Where to output my (+) 12V Siren if i my car don't have the arm system?
Unless you are adding a siren you won't need to connect that.
WestCoastDawson Creek · Jul 23, 2013#173My CM6200 said I need cut the green loop wire inside the brain module, but I can't find it, where is my green loop wire?
CTScottThread starterUSA, CT · Jul 23, 2013#174 Originally Posted by
WestCoast ↑ My CM6200 said I need cut the green loop wire inside the brain module, but I can't find it, where is my green loop wire?
It is inside of the remote starter, not a wire on the car.
WestCoastDawson Creek · Jul 23, 2013#175Thank you so much CTScott, I found it after I opened the CM6200 module.
Now, the wires have been connected, and I have tried to lock and unlock the door, works great.
When the car was running after I take off the key, I still can use remote start to shut it off. But the weird thing is, after I push the remote start button to start my car, the car just flash twice, then nothing happen, however the car will immediately start after I plug in the key without turn the key(just in the lock position even not in the ACCE or ON position).
CTScottThread starterUSA, CT · Jul 23, 2013#176 Originally Posted by
WestCoast ↑ Thank you so much CTScott, I found it after I opened the CM6200 module.
Now, the wires have been connected, and I have tried to lock and unlock the door, works great.
When the car was running after I take off the key, I still can use remote start to shut it off. But the weird thing is, after I push the remote start button to start my car, the car just flash twice, then nothing happen, however the car will immediately start after I plug in the key without turn the key(just in the lock position even not in the ACCE or ON position).
I have only installed a remote starter on a Yaris which has the engine immobilizer and therefor required the key bypass module. It sounds like even though yours does not have the immobilizer that the ECM wants to see the "unlock warning switch". It is a 2 pin connector on the ignition switch with a yellow and a white/black wire. As a quick test, just jump the yellow to the white/black by shoving a piece of wire in the back of the connector. If it remote starts with that jumped, then you will need to hook the yellow wire to the start #2 output of the remote starter.
WestCoastDawson Creek · Jul 23, 2013#177You are the amazing man CTScott, I never done this before, but every thing works great now.
CTScottThread starterUSA, CT · Jul 23, 2013#178 Originally Posted by
WestCoast ↑ You are the amazing man CTScott, I never done this before, but every thing works great now.
Nice! I am glad to hear it is done and working.
CTScottThread starterUSA, CT · Aug 12, 2013#179 Originally Posted by Nadial ↑
Hi guys,
First off, great forum, I have searched for a couple of days and found all the wires (even how to wire throught the firewall 👏) for my DIY alarm install on my 09 two door hatchback, or so I thought.
Surely this is a noob question, but I cannot get the parking lights to flash. My sp-101 manual depicts two (white) 12v flashing light outputs (7.5 amp x 2).
I have tried:
Connecting one white wire to pin 13, parking light (-), on the 13-pin plug by the headlight switch without success
Connecting one white wire to pin 29 (green wire), parking light (+), on 30-pin plug 4A in the dash fuse box without success.
I have tried alternating the two white wires in both positions as well.
It might bear mentioning the the the 12v power input is connected to the gray wire, pin 5, on the 8 pin plug by the ignition swith. Which is supposed to be constant 12v.
Thanks in advance
If you have a green wire in your headlight switch connector, in place of one of the white/black wires, then you would have to use the Pin 29 + connection, instead of the pin 13 white connection.
Check the 10A TAIL and 7.5A PANEL2 fuses in the fuse panel that is under to bottom of the dash to see if you popped one of those fuses. If you connected to - output to pin 29 you would pop it.
CTScottThread starterUSA, CT · Aug 12, 2013#180 Originally Posted by Nadial ↑
The 10A tail is fine, there is no panel 2, only a 7.5A panel 1 beside the 10A tail, and it is fine.
This is what I have for the headlight switch connector
Sorry I had to use a picture from another forum, best I could do in short notice.
I tested the connection for continuity.
The one thing I noticed is that the left front parking light (inside the headlight assembly) is burned out.
Thanks
OK. In that case, if you simply jump the white wire to one of the white/black wires (you can use a paper clip or piece of wire to do so, you should see the tail lights come on). This would do the same thing as the parking light - output on the remote starter.
If you do, then something is not configured correctly with the remote starter or the connection to that wire is not good.
CTScottThread starterUSA, CT · Aug 12, 2013#181 Originally Posted by Nadial ↑
Jumped the wires and the tail lights came on. Made sure the connection between the alarm and the white wire on the plug is fine. Reset defaults on the alarm as well, no luck.
I am out of ideas. Maybe just live without the lights flashing.
It sounds like that output is bad on the remote starter.
eseibel67Canada · Nov 8, 2013#182I am trying to install Avital 4003 so I can use the existing factory remote lock signal as a trigger on an 07 Yaris Sedan.
On connector GD1, there is a brown wire on pin #5, and there is also a brown wire on pin #7. Turns out that the brown wire on pin #7 is the negative (-)lock pulse.
eseibel67Canada · Nov 10, 2013#183I was wrong on post above. The negative pulse on connection above does not have enough juice to trip the remote starter signal.
Instead, I used the passenger unlock (+) pulse and inverted it with a relay to give the remote starter the (-) trigger signal it wants. This wire is located at connector 4H, the pink wire at pin #18.
chadcox82maryland · Nov 19, 2013#184New to the forum but joined specifically because of this thread. I am thinking about installing a remote start on my girlfriends 2007 yaris with power locks but no factory keyless entry. Any suggestions for a simple, reliable yet relatively inexpensive remote start/keyless entry? I was looking at the VIPER 4105V, Are there any other systems you would suggest?
CTScottThread starterUSA, CT · Nov 20, 2013#185 Originally Posted by
chadcox82 ↑ New to the forum but joined specifically because of this thread. I am thinking about installing a remote start on my girlfriends 2007 yaris with power locks but no factory keyless entry. Any suggestions for a simple, reliable yet relatively inexpensive remote start/keyless entry? I was looking at the VIPER 4105V, Are there any other systems you would suggest?
That viper would be a good choice. I am still very happy with the UltraStart that I installed on my 09, back when I got it in October of 2008. I have not had a single issue with it in the 5 years that is has been on there and the range if awesome compared to Avital that I installed on my 08.
JoeVRSt. Louis · Dec 18, 2013#186Hi Scott,
Thank you so much for this great page. I have a 2008 Yaris with power locks but no remote. I would really like to put a remote start and lock/unlock. I don't really need an alarm for it.
I was looking at the suggested models in your document from a few years ago, and I have found most of them are discontinued.
Can you suggest an updated model that would do remote start & lock/unlock that would work on my 2008 Yaris?
Thanks! I really appreciate any helpful suggestions you may provide.
CTScottThread starterUSA, CT · Dec 18, 2013#187 Originally Posted by
JoeVR ↑ Hi Scott,
Thank you so much for this great page. I have a 2008 Yaris with power locks but no remote. I would really like to put a remote start and lock/unlock. I don't really need an alarm for it.
I was looking at the suggested models in your document from a few years ago, and I have found most of them are discontinued.
Can you suggest an updated model that would do remote start & lock/unlock that would work on my 2008 Yaris?
Thanks! I really appreciate any helpful suggestions you may provide.
I just picked up an Ultra Start 1272 XR Pro off ebay for the 2007 I am currently rebuilding for a buddy of mine. $47 is a great deal for it:
http://www.ebay.com/itm/261152420077...84.m1423.l2649 JoeVRSt. Louis · Dec 23, 2013#188Thanks so much!
I just ordered one.
CTScottThread starterUSA, CT · Dec 27, 2013#189 Originally Posted by racefear ↑
Need to find my last wire, please help : door trigger input pin wire(wich monitors all the door)
Connector 4A ??? Wich pin ?
Attached picture not available
Tanks
The Yaris does not have a single door trigger monitor for all doors.
You could either use the pink wire for the dome, or connect a diode to each door wire with the white stripe on the diode pointing away from the wires and connect all of the white stripe ends together and to the door trigger input.
CTScottThread starterUSA, CT · Jan 4, 2014#190 Originally Posted by racefear ↑
ok tanks, for the pink dome wire, did you mean the pin 4 on the 4a connector ?
I don't have the best wirring diagram sheet... 🤷
Tanks
No. The pink one in 4K (the upper left connector in this picture):
Attached picture not available CTScottThread starterUSA, CT · Jan 27, 2014#191 Originally Posted by racefear ↑
Hello all
A neutral safety switch must be install on a manual yaris, optional ? or the sequence of steps to be performed before exiting the car is ok...
What are the other step to do for the manual tranny like put the starter wire of the 'module' to the black wire of the clutch that is not show on the
Yaris 2006+ Remote Start Wiring Guide.pdf ??
In your Yaris 2006+ Remote Start Wiring Guide.pdf, I think the wire color you said for Doors Unlock (-pulse) is not green pin 8 but orange pin 6.
I have a toyota door lock key without bypass. Need to wire somethings for the FACTORY ALARM ?
Almost done but the car don't start after the ready mode procedures ! 🆘
Tanks
A neutral safety switch is a difficult thing to create for a vehicle that does not have one. If you have a remote starter that is designed for use with a manual, and it has one of those arming procedures, then that is fine. If you have one that only has the neutral safety switch input, then you really should figure out a way to add one.
On a manual you would need a bypass for the clutch switch. You would need to feed +12 volts to the black wire to bypass the clutch switch.
The wire that I show for the - unlock is correct, as that is what I have used on quite a few installations. If you use the one that you mentioned it confuses the body ECU and if you use the inside lock switch, once you get out of the car the key fob will not lock the doors.
The - unlock green wire in pin 8 is also the one that will disarm the factory alarm, as the theft deterrent ECU sees it as someone unlocking the door with the key.
CTScottThread starterUSA, CT · Jan 30, 2014#192If I am seeing that correctly, the "bypass" connection really doesn't do anything as wired.
You will need to connect the yellow "starter" wire of the remote starter directly to both the black starter wires on the ignition switch connector and to the black wire on the clutch switch.
CTScottThread starterUSA, CT · Jan 30, 2014#193 Originally Posted by racefear ↑
Did you mean purple `starter' wire of the prostart remote starter ?
Seems to be clear for you... I updated post 202(Relay part), can you take a look please, mod the pic, this can help me and futur user...
Some guys use 1N4004 diode betwen 85 - 86 for protection, usefull ?
Tanks for your time
Correct on the purple. The diagram corrections that you made are good now.
The diode won't hurt anything, but in this case where you are only switching power to another relay coil, it really is not necessary.
xiaoyaWinnipeg · Feb 4, 2014#194Hello CTScott,
Thank you very much for making this nice wiring guide for remote start installation.
I am trying to install a NITRO BMWX-2 way remote start into my wife's 2008 Yaris automatic base model. Meantime, I am installing an aftermarket keyless entry module to control 4 doors.
I went through connections you listed in the wiring guide. Comparing to the wiring manual, I have several questions want to ask you. Please see attached pic for corresponding numbers:
0 in User manual, is it ground in your Wiring Guide?
1 and 8 in User manual, should I connect 1 to the "+" connections you used in installing heating pad (I followed your guide and the pads work beautifully) and connect 8 to " + battery Voltage under sash fuse panel - unused fuse location"?
2 light flash output, I noticed in your wiring guide there are D4P13 for "- pulse" and 4AP29 for "+ pulse". It seems this remote start can do either of them but default with "+ pulse". Is "- pulse" better than "+ pulse"? Any suggestion on this, I read from User manual that I can configue an internal jumper to change between "-" and "+" but I couldn't find the jumper in remote start.
3 Siren output. I am not planning to install siren, should I connect this wire to Horn at D3P8 as suggested in your wiring guide?
4 Trunk release output. I bought an actuator for trunk. How should I determine whether I need a relay and if I need one what kind should I get?
5 Dome light supervision output, it is a nice feature.Is it difficult to achieve?
6 Second Unlock (passenger unlock), I am going to install an aftermarket keyless entry module for 4 doors so I am assume this (press unlock once- open driver door, press twice - open all doors) will be covered by keyless entry module once I connect it with lock and unlock wires of remote start . Do I still need to work on this wire?
7 Ground-when-armed output to starter killer. The user manual looks very complex on this one. Do I need to install this?
8 As mentioned in 1, this remote asks for 2 "+" connections.
9 and 11, my understanding is that 9 is for standard car (my wife's 2008 Yaris is an automatic). 11 is the connection of "Brake Switch" you mentioned as A13P1. Am I correct on this?
10 Bypass Output when remote start, this yaris has no engine immobilizer (checked by using your pictures). So I can just cap this wire, right?
11 brake pedal input, as mentioned in 9. This is the one I should use to follow your wiring guide, right?
12 (+) Ignition of key cylinder (key on) input, in user manual for the key cylinder area the ING1 and ING2 matches Connections D8P1 and D8P6 listed in your wiring guide. Here it asks for a + ignition input again. Do I need this for any good?
13 and 14 Door trigger input. I guess these are for the security reason. Are these difficult to achieve?
My last question is that should I install the keyless entry module with actuators and test them out before installing remote start? For keyless entry, can I also use the "+" connections you used in installing heating pad? I remember that you mentioned in one of the post that + connection is capable to hold up 4 pads and remote start.
Sorry for so many questions. Really appreciate for your information shared with us. best
Xiaoya
camry09Allentown PA · Nov 8, 2014#195Good evening CTScott
Trying to install Valet 561T in 2010 Prius Sedan AT with Factory Alarm
I think i figured out the most of the things except for few
On the 4 Pin Satellate Harness there are few wires that aren't clear for me where to connect
1. Accessory Trigger ( does it go to Conn 8 Pin 2 White wire)
2. Wire 3 Starter Trigger ( does that go to Conn D8 Pin 7 )
And another thing
Heavy Gauge Relay Sattelite
1. Wire 2 Purple do i tap in to D8 Pin 7 Black starter wires ?
2. Wire 3 Orange do i tap in to D8 Pin 2 White Accesory wire?
thank you
Picture lost · imageshack.com
CTScottThread starterUSA, CT · Nov 8, 2014#196 Originally Posted by
camry09 ↑ Good evening CTScott
Trying to install Valet 561T in 2010 Prius Sedan AT with Factory Alarm
I think i figured out the most of the things except for few
On the 4 Pin Satellate Harness there are few wires that aren't clear for me where to connect
1. Accessory Trigger ( does it go to Conn 8 Pin 2 White wire)
2. Wire 3 Starter Trigger ( does that go to Conn D8 Pin 7 )
And another thing
Heavy Gauge Relay Sattelite
1. Wire 2 Purple do i tap in to D8 Pin 7 Black starter wires ?
2. Wire 3 Orange do i tap in to D8 Pin 2 White Accesory wire?
thank you
You would need to post the pages of the 561 manual that describe the wires in question. I wouldn't know off the top of my head.
camry09Allentown PA · Nov 8, 2014#197Repost, sorry
camry09Allentown PA · Nov 8, 2014#198Repost as well
camry09Allentown PA · Nov 8, 2014#199camry09Allentown PA · Nov 8, 2014#200Can't seem to post an image with an url here, posts are being deleted
Sent you a PM
Thank you