I have been getting a lot of questions lately regarding installing remote start on a Yaris, so today I put together a wiring guide for those interested.
Yaris 2006+ Remote Start Wiring Guide.pdf
Yaris 2006+ Remote Start Wiring Guide.pdf
252 posts · 402,288 views · page 1 of 6
SWEET!Originally Posted by CTScott ↑I have been getting a lot of questions lately regarding installing remote start on a Yaris, so today I put together a wiring guide for those interested.
Attachment 30944
Hey Scott,Originally Posted by CTScott ↑I have been getting a lot of questions lately regarding installing remote start on a Yaris, so today I put together a wiring guide for those interested.
Attachment 30944
Originally Posted by Reeves360 ↑Hey Scott,
Seeing as I have installed an OEM alarm which added factory keyless entry as well which remote starter what would you recommend that I use for a remote starter? I'd like to continue to use the Toyota remotes.
I would also prefer to use home made neutral safety switch so that I don't have to perform a sequence of steps every time I park the car. Do you have any suggestions on the switch that I use as well?
On a side note I would like to install the TRD push button start as well down the line even if that means I have to put in my car and turn the car to on. Do you for see any issues having both remote start and push button start. Seem to me that you wouldn't but some of the wiring for the remote start and push button start may tie into some of the same locations.
Thank you for all the excellent help here on Yaris World!
👍
It's a DEI product, so it should be decent. I just read through the install guide for it and It should be very straight forward with my DIY.Originally Posted by jroy ↑Anyone ever try installing a Avital 4113 starter in a Yaris? This was the only one button starter I could find locally and I need it by Wednesday (girlfriend's birthday).
Originally Posted by jroy ↑Hi Scott, this starter has a couple of connections I couldn't match up using your install guide.
FACTORY ALARM DISARM
FACTORY REARM
(+) IGNITION OUT (TO ALARM)
(-) ACTIVATION INPUT
And where is the neutral safety switch connection? Or is that not needed because the motor wont start unless its in park or neutral? Thanks!
-Josh
Whether the (+)Ignition out is required or not for yours will depend on the particular alarm that you are using. You didn't answer above, as to if it is the factory installed OEM one, or an aftermarket one.Originally Posted by jroy ↑For the (+) IGNITION OUT (TO ALARM) it says:
As an add-on car starter: If connected, disconnect the ignition/accessory
input of the remote controlled security or keyless entry system.
Connect the H1/3 YELLOW ignition output to the ignition/accessory
input of the remote controlled security or keyless entry system. The wire
will prevent the host system from sensing that the ignition is on during
remote start operation.
Should I use the "Disarm No Unlock use key sense wire" ? That requires a negative input not a positive input like this one outputs. Should I get a relay and wire it that way?
Also, the (-) ACTIVATION INPUT,
This input comes from the factory set to 1 activation pulse. This means
that it is necessary to have 1 ground pulse on the white/blue wire for
the remote start to activate or to deactivate. The same holds true for the
remote control activation when set to a two pulse setting it is necessary
to press the button twice for the remote start to activate or deactivate.
I can't quite figure out what that means. Would this input be used if you wanted to use the factory lock button? It has a little diagram about a Momentary switch so I really don't know what its talking about.
OK. The TVIP OEM Alarm has a 36 pin connector:Originally Posted by jroy ↑Hi Scott, it is the factory alarm.


The mistaken word tape for tap probably didn't help. Theoretically, if you connect to the black start wire on the ignition switch, you will not be able to start the car with the remote starter, as the alarm ECU has a relay between that wire and the starter relay that allows it to keep the key from starting the car, unless the alarm is deactivated. In order for the remote start to work, you have to connect your remote starter's start wire to a point beyond the alarm starter cut relay.Originally Posted by jroy ↑Um, I'm not following what you're doing with the pin 12 wire?
Yeah I hooked up the brown for lock but no dice. But the bottom right wire (orange i believe) works but only for unlock.Originally Posted by CTScott ↑Did the lock and unlock negative pulse wires are shown on page 7 of the guide not work? I don't recall if they get pulsed when the factory keyless locks/unlocks the doors.
And, no you should be able to unlock the doors with the remote, even when the car is started by the remote starter.
If the orange works for unlock, then the pink directly above the orange should work for lock.Originally Posted by Skylinecar1982 ↑Yeah I hooked up the brown for lock but no dice. But the bottom right wire (orange i believe) works but only for unlock.
And the factory keyless remote doesnt work when I start it just pulsing the wire manually
Thanks Mark
Tried the pink too also no luck but will try again tomorrow.Originally Posted by CTScott ↑If the orange works for unlock, then the pink directly above the orange should work for lock.
I am not catching what you mean about the remote not working?
There are two pinks. Make sure that it's the large one on the end, not the small one in the middle.Originally Posted by Skylinecar1982 ↑Tried the pink too also no luck but will try again tomorrow.
I can take the green wire from the ultra start ( the wire that needs the negative pulse to start.) and I can manually ground the wire twice to make the remote start think it is getting a negative pulse. Then the device will start the car. Once the car is started through the device. The factory remote will not work anymore for the vehicle.
Thanks
Mark
Yeah that is the one that I tried but it was late in the day and I will try again tomorrow.Originally Posted by CTScott ↑There are two pinks. Make sure that it's the large one on the end, not the small one in the middle.
I just downloaded the manual for the 1155. They actually say to connect the pulse to start wire to the unlock rather than lock. They probably do that because of cars that have security that prevents them from starting unless the car was unlocked. That may be why your factory remote gets locked out after starting.Originally Posted by Skylinecar1982 ↑Yeah that is the one that I tried but it was late in the day and I will try again tomorrow.
thank you
Mark
Oh well I tried it on the lock and unlock wires on page 7 but nothing happened. But I did have it working with unlock using the thicker orange wire in the bottom right of the connector but , after it started the remote still wouldn't work. The doors where open but I wanted them to be closed so that I can start it and not have to watch it while it warms up.(security wise.)Originally Posted by CTScott ↑I just downloaded the manual for the 1155. They actually say to connect the pulse to start wire to the unlock rather than lock. They probably do that because of cars that have security that prevents them from starting unless the car was unlocked. That may be why your factory remote gets locked out after starting.
The 1155 has the option to relock after starting, so you could set it up to start on the double unlock pulse and then relock.Originally Posted by Skylinecar1982 ↑Oh well I tried it on the lock and unlock wires on page 7 but nothing happened. But I did have it working with unlock using the thicker orange wire in the bottom right of the connector but , after it started the remote still wouldn't work. The doors where open but I wanted them to be closed so that I can start it and not have to watch it while it warms up.(security wise.)
I have it working but now there is a new problem I cannot get it to respond when I program the unit for more then one pulse. I can get it to work on one pulse but when I go to unlock the car it will shut off. Hence why I need it to work with more then one pulse.Originally Posted by CTScott ↑The 1155 has the option to relock after starting, so you could set it up to start on the double unlock pulse and then relock.
Originally Posted by Skylinecar1982 ↑FYI
I found what was wrong. I have been using your write up the whole time to install this remote start. You have on page 4 that IGN 1 is Green and IGN 2 is Pink. It should be Pink is IGN 1 and GREEN is IGN 2/ ACC. I checked this with the Crimestopper wiring diagram and the Fortin wiring diagram and they both have Pink as IGN 1 and Green as either IGN 2 or ACC.
If you don't have a immobilizer and factory keyless this probably won't make a difference but if you do it could mean the difference between the car starting or not starting.
I spent 3 days thinking something was wrong with the trigger wire I found but in the end it was that. So now I can use Unlock or Lock. But still can't use the remote because Toyota vehicles with factory keyless and immobilizer won't respond to wireless commands when running. May be other Toyota's but I know for sure keyless and immobilizer toyota cars don't.
Thanks anyways everything else was extremely helpful.

Originally Posted by CTScott ↑The Toyota service manual EWDs describe the wires as I listed them and that's how I have them wired to my UltraStart remote starter. I do have the immobilizer and am using a Fortin KEY-OVERRIDE-ALL bypass module. Mine had factory power locks/windows, but not remote keyless entry.
If you start the car with the key, do you see the same behavior, where the remote will not function when the engine is running?
Originally Posted by Skylinecar1982 ↑Yeah started with the key and keyless still doesn't function. This is a known thing for Toyota's to lock out factory wireless when vehicle is running. You got around it by having a keyless that is not fully integrated into the car. It's some sort of security measure I think.
As far as the wires go if Toyota says that green is IGN 1 then it is IGN 1 but crimestopper and fortin have listed it as IGN 2. And this is the only thing that I needed to change in order to get the vehicle remote start working. So I am happy. Wonder who has it wrong Toyota or others.
Again thanks.
Did you try the white separately as well? The reason I ask it that the two are listed as input an output, but it is not clear as to whether the in and out are relative to the body ECU or to the door control receiver.Originally Posted by Skylinecar1982 ↑Yeah I found the two wires White and Red I disconnected the red and the wireless didn't work anymore nevermind when the key was in.
Do you know exactly what happens between the BCM and the Door Receiever within those two wires? I don't see any of the wires going directly to the door lock system. So the BCM has to do the work to cut it off.
So the issue is probably the key ecu telling the BCM that the key is in the ign. And to block the signal between the two may cause more issues then I have already.
If you did, then ON and ACC would act the same when you turn the key.Originally Posted by tchwue ↑can i join pink and green wire together for remote start? thanks
If the starter cranks, but the car doesn't start, then it sounds like your car has the engine immobilizer, which requires a bypass module (like the Fortin one).Originally Posted by tchwue ↑because my issue now is, i connect 12v remote start cable to pink, add a relay to to provide 12v to green when there is power supply to pink. it doesn't work. it will crunk the starter but engine won't run. need your help, thanks
ok, thanks man...Originally Posted by CTScott ↑If the starter cranks, but the car doesn't start, then it sounds like your car has the engine immobilizer, which requires a bypass module (like the Fortin one).
Stick your key in the ignition, but don't turn it and then start the car with the remote starter. If it cranks and runs, then you definitely need a transponder key bypass module.
It sounds like the positive light feed is backfeeding the flasher relay. The Yaris is really a negative switched, not positive switched vehicle. I wired mine as a negative, but posted the positive option, as I noticed it documented on a keyless entry DIY. Looking at the EWD, wiring positive to 4A-29 will cause a backfeed. It will not hurt anything, but will produce that annoying buzz.Originally Posted by adam1981 ↑Thanks for the guide in the OP... I successfully connected a remote start/alarm with the use of it. I have to do some more research for some of the alarm items though.
I do have one area of concern. When the Yaris is running under the control of the remote start unit, there is a buzzing sound coming from underneath the dash from what looks like a relay - but there is no label for it (I already looked in the manual too). It is the blue box on the bottom center of wiring harness panel where you connect the positive parking light.
The sound goes away after you put the key in, on, and press the brake.
Is this sound normal for this vehicle when using remote starts?
I have two wires: 1) Parking Light Flasher Feed 2) Parking Light Flasher OutputOriginally Posted by CTScott ↑It sounds like the positive light feed is backfeeding the flasher relay. The Yaris is really a negative switched, not positive switched vehicle. I wired mine as a negative, but posted the positive option, as I noticed it documented on a keyless entry DIY. Looking at the EWD, wiring positive to 4A-29 will cause a backfeed. It will not hurt anything, but will produce that annoying buzz.
With your remote starter, can you select negative instead and wire to the negative wire instead? If not, you can use a standard automotive relay as an inverter:
Picture lost · images.the12volt.com
Hang on - It sounds like you have both a positive and a negative hooked up. You can only do one or the other. What remote starter are you using?Originally Posted by adam1981 ↑I have two wires: 1) Parking Light Flasher Feed 2) Parking Light Flasher Output
I have 2 connected to the parking light switch wire under the column and 1 connected down there by that relay. The remote start manual says I can connect 1 to a standard 12V source for + switching, so I guess that is what I need to do.
I realized my error and edited my post... :) Thanks for the help!Originally Posted by CTScott ↑Hang on - It sounds like you have both a positive and a negative hooked up. You can only do one or the other. What remote starter are you using?
Very good - The wording in the remote starter manuals can be mighty confusing.Originally Posted by adam1981 ↑I realized my error and edited my post... :) Thanks for the help!
Right now from what I can remember this is what else I need :Originally Posted by CTScott ↑Very good - The wording in the remote starter manuals can be mighty confusing.
For the additional alarm wires, post up what you need and I'll add all of them to the document.