🤘
Stay tuned
1,311 posts · 595,379 views · page 9 of 27
Replies continued
138hp at the wheels naturally aspirated?
All of our numbers are from a Dynapack (hubs), so YMMV. But it is making more HP NA than it did (from #s posted on the Tein website) with FI, and weighs 300+lbs less.Originally Posted by thebarber ↑138hp at the wheels naturally aspirated?
Good info here on Dynapack VS Dynojet numbers:
http://home.earthlink.net/~spchurch/id12.html
jason you rulezzzzzzzz :)
I remember picking up that carbing bar from you those many many hours ago. That thing is really lookin' good.
What tire sizes are you running now ? Just out of curiosity how many tires will you go through at Road America ?
Jason, my dad is going up to the runoffs with Chip Van Vurst(I don't know if you know Chip) he runs in SM. Anyways I told my dad to look out for you. To take pics and video of the Yaris. His name is manny. Good luck out there.
Still on the Goodyear 23x9.0x15 (23" dia, 10.4" wide, on a 15"x7" wheel).Originally Posted by soloecho2 ↑What tire sizes are you running now ? Just out of curiosity how many tires will you go through at Road America ?
I expect we will use up two sets of drys, and have a couple of sets left over with only a few laps on them.
Most of the tires we took are for the SSC Nissan, it will go out every session on fresh tires - I think we have five sets of dry tires for it.
Here is the dyno graph before the AEM EMS 2.
Picture not included in this copy
Picture not included in this copy
^ awesome, so this is just with the ???? my mind just blanked on what it's called. The controller the car came with.
That was with the CamCon and all the bolt-ons. Still had the stock head and cams, also had stock rev limiter.Originally Posted by Bluevitz-rs ↑^ awesome, so this is just with the ???? my mind just blanked on what it's called. The controller the car came with.
Although as I sit here comparing before and after dyno charts we are wondering if we wasted money on cams... While we picked up a some good top end, we actually lost Tq. On fast tracks like Road America the top end is what you want, but it could hurt us at slower tracks.
everything is a tradeoff when trying to make power in a small motor.
Yep... Just not sure we made the right trade. I will find out for sure next week.Originally Posted by Bluevitz-rs ↑everything is a tradeoff when trying to make power in a small motor.
I think I would feel better about revving the piss out of this thing if it was not on a stock bottom end.
I think it's just the con-rods you need to worry about. though I've accidently over-reved my engine to 8600 and luckily it only bent some vavles. So I know it'll spin that high, but for how long 🤷
So... Anyone in the area of Elkhart Lake, WI (Road America) have a stock crank pulley I can use for a few days? I have mine being sent Fedex overnight, but does not get here until Monday.
Picture not included in this copy
This one split in two at about 7000rpm at the exit of turn 14. 😲 If this is the only problem we have at the Runoffs I will be happy.
Picture not included in this copy
Picture not included in this copy
This one split in two at about 7000rpm at the exit of turn 14. 😲 If this is the only problem we have at the Runoffs I will be happy.
Picture not included in this copy
Dang, that sucks....... for you and NST
^ no kidding, that sucks! it's a one piece pulley too, wow.
The bang, "wtf was that", and then watching it pass me on the track was interesting.Originally Posted by cali yaris ↑^ no kidding, that sucks! it's a one piece pulley too, wow.
Doing a lap with no water pump and alt was not fun... Killed the motor and coasted as much as I could, but still saw 240 on the water.
😲 unbelievable that was always my night mare that something from the car will overtake me
did you get new one ?
did you get new one ?
No, the only one we could find at a dealer was in Indy, 5 hours away, and they are not open until Monday. Just have to wait for Fedex to show with ours, and hope we get on track for Qual.Originally Posted by henry33 ↑😲 unbelievable that was always my night mare that something from the car will overtake me
did you get new one ?
and how is the race going ? where can I found some video because the oficial site is not build for mac :(
My race is on Saturday. So far we have one and half practice sessions done. 😉 We used that to test the news suspension (AST shocks, Eibach springs), and learn the track. Other than the pulley all is good.Originally Posted by henry33 ↑and how is the race going ? where can I found some video because the oficial site is not build for mac :(
We were able to watch the live SpeedcastTV video of last years race in our office on Mac's. 🤷 Make sure your flash player is up to date.
Off to the track...
Good luck Jason
Our setup:
Picture not included in this copy
Picture not included in this copy
nice ;)
I just want to ask if you have some cockpit video you can share with us ?
thanks
I just want to ask if you have some cockpit video you can share with us ?
thanks
We did not run any in practice... Should have some after Qual 1 today.Originally Posted by henry33 ↑nice ;)
I just want to ask if you have some cockpit video you can share with us ?
thanks
coool don't forget to share with us ;)
my laptop died only have my psp for web no pics or video this week :(
don't worry we will wait ;-) how is the run going ?
Wow, what a week... And having no computer sucked. 😠
After the pulley failure in practice we had to use our qualifying sessions for some fine tuning. We had the engineers from Goodyear on hand to help evaluate our alignment and tire pressures.
For the second qual session we made a spring change, and went the wrong way. The car started to pogo, on three wheels, and was really overworking the left front.
With only one session left we went back to our first set of springs, which gives us a good balance, but is a little to soft. We finally got the tire pressures and alignment optimized for RA, but it was so hot in final session we ended up going slower - however, relative to how much others slowed in the heat we knew we made the right choice.
Qualified 13th, about what we expected after getting the final assembly done on the car one days before we shipped. Got a great start, moved up a number of spots. Running in the draft during the race resulted in 3 second quicker times. The Yaris was very strong on the brakes, but with the tall gearing did not have the grunt off the turns.
Near the end of the race (I think it was lap 9 or 10) I got in to turn three and the car hopped and slid wide, not sure there was fluid or something on the track, or if the crash bolts slipped. I get down to turn six and the car goes up on two wheels, quick. Turned the wheel strait and went in the grass, which was not smooth, caught air and dug in the air damn. When I got back on track the steering wheel was 45 degrees off center. So either the crash bolts slipped, or something is bent. I took it easy for a few turns, to make sure everything was ok, then got back on it.
At this point the Honda that had been pulling me around the track was long gone. The last few laps clicked off without issue, and we came home in eighth place.
We hit our goal of a top ten finish, and were very happy to bring it home in one piece - our SSC Nissan on the other hand is in need of some bodywork.
As I understand it speedcasttv.com will have the edited races up after the first of Oct. Once I get my laptop fixed, or get a new one, I will post up the video I took.
After the pulley failure in practice we had to use our qualifying sessions for some fine tuning. We had the engineers from Goodyear on hand to help evaluate our alignment and tire pressures.
For the second qual session we made a spring change, and went the wrong way. The car started to pogo, on three wheels, and was really overworking the left front.
With only one session left we went back to our first set of springs, which gives us a good balance, but is a little to soft. We finally got the tire pressures and alignment optimized for RA, but it was so hot in final session we ended up going slower - however, relative to how much others slowed in the heat we knew we made the right choice.
Qualified 13th, about what we expected after getting the final assembly done on the car one days before we shipped. Got a great start, moved up a number of spots. Running in the draft during the race resulted in 3 second quicker times. The Yaris was very strong on the brakes, but with the tall gearing did not have the grunt off the turns.
Near the end of the race (I think it was lap 9 or 10) I got in to turn three and the car hopped and slid wide, not sure there was fluid or something on the track, or if the crash bolts slipped. I get down to turn six and the car goes up on two wheels, quick. Turned the wheel strait and went in the grass, which was not smooth, caught air and dug in the air damn. When I got back on track the steering wheel was 45 degrees off center. So either the crash bolts slipped, or something is bent. I took it easy for a few turns, to make sure everything was ok, then got back on it.
At this point the Honda that had been pulling me around the track was long gone. The last few laps clicked off without issue, and we came home in eighth place.
We hit our goal of a top ten finish, and were very happy to bring it home in one piece - our SSC Nissan on the other hand is in need of some bodywork.
As I understand it speedcasttv.com will have the edited races up after the first of Oct. Once I get my laptop fixed, or get a new one, I will post up the video I took.
cool thanks :)
Goodyear engineers are worthless and you saw that first hand by making changes based on their bad advice and seeing what happened. ;) I've seen it time and again. I used to work for a supplier who sold them test instruments and they were always clueless.
The spring change was my idea, to get more rotation. They were consulted for pressure and alignment changes, and were spot on. 🤷Originally Posted by knowmercy ↑Goodyear engineers are worthless and you saw that first hand by making changes based on their bad advice and seeing what happened. ;) I've seen it time and again. I used to work for a supplier who sold them test instruments and they were always clueless.
Goodyear engineers are worthlessAll of them? C'mon man....
Here is the start: http://www.youtube.com/watch?v=3yy8M3vK910
cool video ;)
Just unloaded the Toyota transporter. No chance of getting everything home in one trip, we brought back twice as many tires as we took, plus a spare engine and trans for the RX-8 we brought back.
The boss is in FLA for Indycar... So we commandeered his office. 😆
Picture not included in this copy
The boss is in FLA for Indycar... So we commandeered his office. 😆
Picture not included in this copy
Some footage from the race: http://www.youtube.com/watch?v=R_mlPp8TfxA
The link is not working for me
Works for me. 🤷Originally Posted by soloecho2 ↑The link is not working for me
wow i need to go through this again, I didn't realize how completely stripped your car is.
Loud too, fun stuff.
Loud too, fun stuff.
🎉Originally Posted by Jason@SportsCar ↑Some footage from the race: http://www.youtube.com/watch?v=R_mlPp8TfxA
love the office pic tires > TV
win
win
Works OK now.
Over the weekend Speedcasttv.com posted up the first days races. The SSC Nissan Sentra that we built as a project car a few years back - got the car race ready and on track for $3k - is in this race with Philip Royle driving. He ended his day early after hitting debris and getting two flat tires. 🙁
The Yaris did make the intro, around 18sec you catch a shot of it.
http://speedcasttv.com/scca/#/races/205
The Yaris did make the intro, around 18sec you catch a shot of it.
http://speedcasttv.com/scca/#/races/205
Got a great shot of the Yaris from Toyota Motorsports:
Picture not included in this copy
Picture not included in this copy
^ awesome
cool pix I have it on the desktop ;)
If you make it to SEMA make sure to stop by the Toyota booth... You can see the SportsCar Yaris, and get the #99 T-shirt. 👍
jason, does toyota plan to keep promoting and developing parts and support for the yaris in SCCA?