Yarisworld Archive

New seats and how i did it !!!!

35 posts · 14,838 views

jm350Original postCanada · Jun 7, 2009#1
Hello everyone,

A few weeks ago i bought two seats (sport style or race style).
To install the driver side seat it was easy. But, the passager one.....was not so easy at all,
because of those fu***ng sensors of course. 😢

First, here's my new seats.... 🤘🎉

Picture lost · www3.sympatico.ca

And this is the first part of the installation....

One thing to keep in mind (very important); Never disconnect any sensors during the installation (except the seat belt one, there's no probleme if you disconnect this one).
If one or more sensors is disconnected, you have to go to the dealer as soon as possible to reset the system.

Here's how those sensors works...

There's four sensors under the passenger seat called "OCSAA" (Occupant Classification System for Advanced Airbag) and they works depending the weight of the passenger. Those sensors send a signal to the "ECU" (Electronic Control Unit) of the system (also under the seat) to determine the speed of the airbag explosion.

Those sensors support the total weight of the passenger and the seat with a bolt (fix point)on each of them.

Here's some pics to explain (sorry the texts in the pics are in french but i traduced them)....

There's four sensors under the passenger seat and they works depending the weight of the passenger.
A "fix point" (bolt) move beside the sensor to send a signal to the ECU.
Picture lost · www3.sympatico.ca

This is one of the "fix points" of the seat and the sensors
Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca

One part of the sensor assembly move depending the weight of the passenger.
Picture lost · www3.sympatico.ca

The rear sensor (right side) and his bolt (fix point) on the seat.
Picture lost · www3.sympatico.ca

The front and rear fix point.
Picture lost · www3.sympatico.ca

The front right sensor...

Picture lost · www3.sympatico.ca

The rear right sensor...

Picture lost · www3.sympatico.ca

Those four sensors without the seat.....

Picture lost · www3.sympatico.ca

And now some modifications to install my new seat.
Of course i kept the original tracks but i made new brackets to put the seat at the same height of the driver one. If i kept the original brackets, the seat will be 4 inch too high. Nothing was broken, damaged or cut, just in case i have to put back the original seat !!! 😁

Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca

...to be continued tomorrow.... (sunday).........

😁😁

Replies 34

eTiMaGoBangkok, Thailand · Jun 7, 2009#2
I like where this is going 🙂 👍
JeemeeCentral Arkansas · Jun 7, 2009#3
Looking good! So are you keeping the sensors in working order with the new seats?
1NZYaris1New Zealand · Jun 7, 2009#4
😲 Could you make a few hundred set's please , or fully translate the photo's
into english 😁 please.
i could see the wife hateing this mod , might just end up getting my yaris back 😆. 🙇🙇🙇🙇
jm350Thread starterCanada · Jun 7, 2009#5
For the next part....

I had to re-aligned the front right sensor (next first image), to be sure it has enough room between the sensor and the top bracket (next second and third images).

Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca

Yes, it's my sensual knee at the left !!!!! 😆
Picture lost · www3.sympatico.ca

The top bracket is installed + you can see (in color) the next part of this modification to be come this week.

Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca

Now the rear left sensor. It's very important (of course) to keep in place the original bracket who hold the seat belt "buckle". And just put the new bracket where the sensor will be.

Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca

I come back this week with the rest of that modification.

🤘🎉
cali yarisCanoga Park, CA · Jun 7, 2009#6
Really COOL. What about the pressure sensor that is inside the passenger seat? You can't take the seat out without disconnecting that.
jm350Thread starterCanada · Jun 7, 2009#7
Originally Posted by cali yaris ↑
Really COOL. What about the pressure sensor that is inside the passenger seat? You can't take the seat out without disconnecting that.
Well, in my Yaris (2007 CE) there's no sensor inside the seat,
just those four sensors. These ones are "pressure" sensors, like i explained in the begining of that post.

It controls the explosion of the airbag, depending of the weight of the passenger.

😉
fujiHonolulu · Jun 8, 2009#8
Fantastic fabrication skills! There has to be an easier way!

The only sensor I am concerned about is the pressure sensor which will activate the airbag. The other one is the seatbelt sensor. Either find a resistor to bypass this one or disconnect the alarm.

If we put our heads together we can do it!

BTW - those seats look fantastic - where did you get them???🎉
jm350Thread starterCanada · Jun 8, 2009#9
Originally Posted by fuji ↑
.....The only sensor I am concerned about is the pressure sensor which will activate the airbag. The other one is the seatbelt sensor......
Like i try to explain.....

There's 4 pressure sensors who control the airbag !!
Those 4 sensors are connected to a box called ECU and that ECU is connected to the airbag. So that assembly of four sensor control the airbag in combination with the seat belt sensor.

But during the modification you can disconnect the seat belt sensor but not the pressure ones.

And for me i thing there's no other way, you have to keep these sensors and make them fonctional.

😉
twowheelsCA · Jun 8, 2009#10
My understanding is that the ECU *DOES* use the seatbelt sensor during airbag deployment to decide how much force/speed to use when opening the bag as an unbelted occupant has different needs than a belted occupant.
jm350Thread starterCanada · Jun 8, 2009#11
Yes, in combination with the sensors who will tell to the ECU if it's an adult or a child sitting on the seat. So, the speed/force of the airbag deployment will be different.
That's what the 4 sensors are for !!

😁
jm350Thread starterCanada · Jun 13, 2009#12
Ok, This is the next and final step.........finally !!! 😉

This is the front left bracket i made;

Picture lost · www3.sympatico.ca

...with the sensor....

Picture lost · www3.sympatico.ca

Almost finished...

Picture lost · www3.sympatico.ca

...the brackets are now complete;

Picture lost · www3.sympatico.ca

I did a cut in the middle let move a part of the original track.

Picture lost · www3.sympatico.ca

Now the seat supports.

Picture lost · www3.sympatico.ca

The brackets are ready now to receive the new seat.

Picture lost · www3.sympatico.ca

...job done completly... 😁😁

Picture lost · www3.sympatico.ca

Now i have two great looking seats for my little yaya !!! 😁

Picture lost · www3.sympatico.ca
Picture lost · www3.sympatico.ca

Ok, now it's time to test those sensors (the airbag lamp in dash)...

First, i put nothing on the seat (I make that test because the new seats are a bit heavier than the original ones.)
And i buckle-up each seat belts..
...and i sit on the passanger seat. After a few seconds i get out of the car (so the seat is empty once again).

Résults....everything works very good !!!

JM350 approuved !!

👍👍
ProhibitOklahoma City · Jun 13, 2009#13
Very nice work! 👍
TinyGiantRochester, NH · Jun 13, 2009#14
sweet too bad the stock black covers dont fit over the bracket to cover the harsh lines of the brackets..

maybe you could paint them black or something to match :)
schleppyBoston, MA · Jun 13, 2009#15
I really, really, really want to replace my drivers seat but that looks like a lot of work...
TerrorizeToronto · Jun 13, 2009#16
So wait....unless i do all this work...i'm losing airbag function if i decide to change the driver seat??? Damn..................
jm350Thread starterCanada · Jun 13, 2009#17
Originally Posted by schleppy
I really, really, really want to replace my drivers seat but that looks like a lot of work...
Originally Posted by Terrorize
So wait....unless i do all this work...i'm losing airbag function if i decide to change the driver seat??? Damn..................
There's no problem with the driver seat 'cause there's no sensor to deal with.
You just have to unpluged the seat belt connection (and re-pluged it when your modification is finished).
I didn't take any pictures of the driver side brackets 'cause is too easy to make the modification.

So don't be scared to change your driver side seat, it's very very very much more easier and simple to do it than the passenger side. It tooks me around 3 hours to do it and around 8 hours for the passenger seat.

Good luck to both of you guys and if you need some tricks....ask me by "PM".

😁
jm350Thread starterCanada · Jun 13, 2009#18
Originally Posted by TinyGiant ↑
sweet too bad the stock black covers dont fit over the bracket to cover the harsh lines of the brackets..

maybe you could paint them black or something to match :)
I know, later this summer i will do something about those brackets.
I have other priorities for now, like........clean the engine bay !!!!

😁
vtencolumbus · Jun 14, 2009#19
🤤 can you help me make another one please 🤤
jm350Thread starterCanada · Jun 14, 2009#20
Originally Posted by vten ↑
🤤 can you help me make another one please 🤤
Driver or passenger ??? 😉
fujiHonolulu · Jun 14, 2009#21
Is there a way of applying a clamping force on the sensors to fool them into thinking there is an occupant? This way a simple mounting system for the passenger seat can be utilized.
vtencolumbus · Jun 14, 2009#22
Originally Posted by jm350 ↑
Driver or passenger ??? 😉

how about both side sir 😁


shoot me an email to dwitan@yahoo.com

thanks
twowheelsCA · Jun 15, 2009#23
Originally Posted by fuji ↑
Is there a way of applying a clamping force on the sensors to fool them into thinking there is an occupant? This way a simple mounting system for the passenger seat can be utilized.
The sensor is more advanced than just present/absent. It also takes into consideration the weight of the passenger during deployment.
jm350Thread starterCanada · Jun 15, 2009#24
Originally Posted by vten ↑
how about both side sir 😁


shoot me an email to dwitan@yahoo.com

thanks
Just sent !! 😉
jm350Thread starterCanada · Jun 15, 2009#25
Originally Posted by twowheels ↑
The sensor is more advanced than just present/absent. It also takes into consideration the weight of the passenger during deployment.
+1 👍
TerrorizeToronto · Jun 26, 2009#26
Originally Posted by jm350 ↑
There's no problem with the driver seat 'cause there's no sensor to deal with.
You just have to unpluged the seat belt connection (and re-pluged it when your modification is finished).
I didn't take any pictures of the driver side brackets 'cause is too easy to make the modification.

So don't be scared to change your driver side seat, it's very very very much more easier and simple to do it than the passenger side. It tooks me around 3 hours to do it and around 8 hours for the passenger seat.

Good luck to both of you guys and if you need some tricks....ask me by "PM".

😁
Thanks dude....

I'm getting a local shop that is making me the brackets and will be handling all parts of the install...i'll be referencing this thread if they have issues...but they've been doing this for awhile...so nothing new, except the install is done on a yaris...which they haven't worked on before.
ImportRacer88Meshoppen, Pa 18630 · Jun 27, 2009#27
hey where did u get those dimind plate floor mats
jm350Thread starterCanada · Jun 27, 2009#28
Originally Posted by ImportRacer88 ↑
hey where did u get those dimind plate floor mats
A member of the yaris club in my town but i don't know where he found them !!

😉
MGarganoNJ · Aug 3, 2009#29
What happened to all the pics?
fmicleSan Jose, CA, USA · Aug 3, 2009#30
Is it just me or why can I only see one picture, the one with the seats against the wall? Can't see any of the other pictures... Anyone having the same problem?
MGarganoNJ · Aug 3, 2009#31
Originally Posted by fmicle ↑
Is it just me or why can I only see one picture, the one with the seats against the wall? Can't see any of the other pictures... Anyone having the same problem?
Wondering the same thing
MGarganoNJ · Aug 5, 2009#32
Anyone? Pics? Bueller?
jm350Thread starterCanada · Oct 18, 2009#33
I had to delete all the pics because my "web-space" is very small.

I received alot of emails and private messages to see those pics again.

here's the link where i put them and this time they will stay there for a long time (as long as possible).

enjoy !!! 😁

http://s392.photobucket.com/albums/pp4/JM-350/seats/

😉
TinyGiantRochester, NH · Oct 18, 2009#34
blue tint?


can i get a picture of the outside ? :)