texkidOriginal postSugar Land, TX · Jun 26, 2009#1First off, I really should THANK Echo-hrs for the idea. If he never mentioned in the first place, I probably would've never know to do this to my car. I went to my mechanic for some help. After taking a look at my car, he definitely agreed that the Low Pressure line needed to be insulated.
I purchased a meat thermometer to get a reading on how its running BEFORE I started doing the insulation. Below is the reading with the A/C set to (4) on Recirculating, with all vents open; driving from work to home (roughly 20 minutes) ABOUT 50-DEGREES
Picture lost · texanurse.com
Here is temp, with the car in the drive-way and windows half open. Its 120-freaking-degrees!
Picture lost · texanurse.com
AND FINALLY, here is the temp AFTER the insulation driving for 15 minutes. A DROP OF ALMOST 10-DEGREES!
Picture lost · texanurse.com
So, without further delay, on with the DIY.
Disclaimer: I am not responsible for what happens to your car. Do this at your own risk.
Tools:
- A pack of foam pipe covers (.75 cents at Wallmart)
- A pack of 6 inch wire ties or whatever you call them
As far as the zip ties are concerned, DO NOT tie them too tight like I did. Just enough tension to keep them in place is all that is needed.
- A meat thermometer
- A couple bottles of water
- SHADE!
Instructions:
Lets start with what the hell we are insulating. It is the low pressure line going from the firewall to the rubber hose before it hits the condensor. Its marked with a pink line at the firewall and has a pressure valved labeled "L". When run the A/C, this line should be the only one that is COLD to the touch. The smaller line that sits below it should be open to air as it is taking hot air out of the cabin and back to the condenser.
Picture lost · texanurse.com
Picture lost · texanurse.com
Picture lost · texanurse.com
next: get your foam pipe insulation and check to see if it fits. If its too loose, you can trim off a bit. But just a BIT!
-Start at the firewall end since it is most difficult and cramped part of the job. At this point, it is recommended that the engine is cool to touch. I singed a couple of arm hair before I realized that. LOL!
Picture lost · texanurse.com
-Run it as much as you can, once you hit that big, "drum" looking thing, cut and start tying it down. As far as that "drum" looking thing, you're just going have to get creative and find a way to cover it. But it does make a difference when you do.
As far as the zip ties are concerned, DO NOT tie them too tight like I did. Just enough tension to keep them in place is all that is needed.
Picture lost · texanurse.com
-For the other side, grab a piece and run it from the front side and thread it under the engine mount. Tie that down very well and make sure nothing can hit the belt or the alternator.
Picture lost · texanurse.com
Picture lost · texanurse.com
-For the rest of the low pressure line, just keep tying it down until you hit the rubber hose. I shouldn't have to tell you this, but cut holes where needed such as the low pressure valve and that do-hicky you see below.
Picture lost · texanurse.com
-AND YOU'RE DONE! Cut off the excess straps so they won't get tangled into anything.
Replies 217
texkidThread starterSugar Land, TX · Jun 26, 2009#2 Originally Posted by echo_hrs ↑
Cool...Glad that it worked!...
Cheers
Thank-you good friend.
One thing I did notice is that the air seems to get cold faster at startup than before and it actually feels
colder than before. Like my old Escort.
BailOutReno, Nevada, USA · Jun 26, 2009#3That's a nice write-up but wouldn't it be easier to use a foam and foil wrap tape than zip tying ever few centimeters?
This is what I use on my hot water pipes in our garage, and on the above-ground segment of our sprinkler system:
http://www.homedepot.com/webapp/wcs/...3+90063+531155 cali yarisCanoga Park, CA · Jun 26, 2009#4that is an A+ DIY - thanks for posting it. Can I copy it to my e-magzine? I think even other car owners could figure out how to do the same thing.
Sodium DuckWestern Mass. · Jun 26, 2009#5Very good idea. Will be doing this on the weekend!
texkidThread starterSugar Land, TX · Jun 26, 2009#6 Originally Posted by PK198105 ↑
texkid, you kinda went apecrazy with the zip ties, you want the wrap to be resting on the pipe and not be squeezed you are taking out the air in the foam and therefore the insulator.Air is the best insulation. ideally you want it to be tight enough to not move but loose enough so there is air in the foam. ill post my pics when i get home
You are right. I need to redo it. I'll change the DIY to reflect that.
Originally Posted by
BailOut ↑ That's a nice write-up but wouldn't it be easier to use a foam and foil wrap tape than zip tying ever few centimeters?
I was thinking that. But my biggest fear was that this whole idea wouldn't work in the first place. And so I figured I shouldn't invest too much into it. The zip-ties were a good a idea at the time since if I were to screw up or it didn't work, it would have been easy to just cut the ties off.
Originally Posted by
cali yaris ↑ that is an A+ DIY - thanks for posting it. Can I copy it to my e-magzine? I think even other car owners could figure out how to do the same thing.
Sure, I don't see any harm in it.
toastNappanee, IN · Jun 26, 2009#7🎉 This is a great idea. I had forgotten that I had done the same thing to my old ranger many years back and it worked great. That beast was 14 years old when I got rid of it and the a/c was the only thing that still worked properly on it. +1 on the excessive zip ties though. All that crushing will reduce the insulation ability some and it's just more work than needed.
AlexNet0Rockland, ME · Jun 26, 2009#8that is a great idea, I always think about how the AC should be colder during the hotter days here in the summer.
texkidThread starterSugar Land, TX · Jun 26, 2009#9 Originally Posted by PK198105 ↑
i can now verify this as I did the same thing today during my break. It works very well and the air coming from the vents is definitely colder than before, also the interior cools down faster, now you can set your dial to 2 and be content as it will keep the same temperature.
We could also insulate the other pipe for even quicker cooldown but that is to be experimented further.
It would interesting see what temperature readings you're getting since you insulated the pipe past the rubber hose. If it is cooler than my reading then more foam insulators is in order! 😁
If you want, you can replace my "AFTER" images with yours since I put on the zip-ties too tight. Just a thought.
auxmikeLI, New Yawk · Jun 26, 2009#10Is this a safe practice?
If so, why did'nt Toyota do it in the first place?
Wonder if that foam could MELT with the heat under that hood.....😕
YarisSedanCalifornia - Bay Area · Jun 26, 2009#11Lot of things the vehicle should have come with from the factory but they only install what is bare minimum required to cut production costs. Like for example all yaris should have a swaybar from the factory but it wasnt cost effective for a basic commuter car
texkidThread starterSugar Land, TX · Jun 26, 2009#12 Originally Posted by
auxmike ↑ Is this a safe practice?
If so, why did'nt Toyota do it in the first place?
Wonder if that foam could MELT with the heat under that hood.....😕
-Is it safe? I dunno. I am assuming as long as it doesn't come in contact with the belt or other moving parts, it'll be ok.
-Why Toyota didn't do this? Heck if I know. Costs? Research? Maybe they thought 50-degrees was enough? One thing I do know is that "most" of the domestic cars I've seen have the rubber hoses. I think maybe aluminum pipes last longer than rubber hoses?
-Melting foam? Probably not. That PCV line is foam as well and in some places comes in closer contact to the heat of the engine.
YarisSedanCalifornia - Bay Area · Jun 26, 2009#13Hmm i think i may do this mod but making it more clean and factory looking using bailouts idea.
CTScottUSA, CT · Jun 26, 2009#14 Originally Posted by
auxmike ↑ Is this a safe practice?
If so, why did'nt Toyota do it in the first place?
Wonder if that foam could MELT with the heat under that hood.....😕
I was thinking the same thing. There are high temp and ultra high temp pipe insulations, but they are pricey.
Polyethylene pipe insulation (which is the kind you get at home improvement centers) is only rated to 180F or 200F.
Silicone pipe insulation is rated for 500F, mineral wool can handle 800F, Flexible ceramic at 1500F, etc. McMaster-Carr has a wide selection of industrial pipe insulation.
The other issue besides temp rating is fire rating (ASTM E84 rating). We ran into an issue UL testing a battery pack because of insufficient rating on the closed cell foam we were using the keep the batteries from banging around.
auxmikeLI, New Yawk · Jun 26, 2009#15Wonder if it affects the warrentee too.....🙁
n00bCanada · Jun 26, 2009#16Ok, I guess I should finally post.
Lets start with what the hell we are insulating. It is the low pressure line going from the firewall to the rubber hose before it hits the condensor. Its marked with a pink line at the firewall and has a pressure valved labeled "L". When run the A/C, this line should be the only one that is COLD to the touch. The smaller line that sits below it should be open to air as it is taking hot air out of the cabin and back to the condenser.
That is wrong.
The LOW pressure line is for refrigerant going to the COMPRESSOR. The HIGH pressure line is for refrigerant going to the EVAPORATOR.
Both lines should be insulated. Insulate the low pressure side to keep the refrigerant a bit cooler going into the compressor and insulate the high pressure side to prevent the refrigerant from absorbing heat from the engine bay.
Your pipe insulation may melt (I don't know how hot this line gets) if you insulate the line going from the COMPRESSOR to the CONDENSER
low > compressor > condenser > high > evaporator > repeat
texkidThread starterSugar Land, TX · Jun 26, 2009#17 Originally Posted by
CTScott ↑ I was thinking the same thing. There are high temp and ultra high temp pipe insulations, but they are pricey.
Polyethylene pipe insulation (which is the kind you get at home improvement centers) is only rated to 180F or 200F.
Silicone pipe insulation is rated for 500F, mineral wool can handle 800F, Flexible ceramic at 1500F, etc. McMaster-Carr has a wide selection of industrial pipe insulation.
The other issue besides temp rating is fire rating (ASTM E84 rating). We ran into an issue UL testing a battery pack because of insufficient rating on the closed cell foam we were using the keep the batteries from banging around.
Hmmm....
At what temperature does the engine block reach when its running at normal range?
On the packaging, that the foam covers came in, it states that it is safe for temperatures as high as 212*F.
If I need better insulation, that's fine with me. I am willing to make a compromise and pay a little more so long as I am guaranteed that it'll keep the A/C cold.
texkidThread starterSugar Land, TX · Jun 26, 2009#18 Originally Posted by
n00b ↑ Ok, I guess I should finally post.
That is wrong.
The LOW pressure line is for refrigerant going to the COMPRESSOR. The HIGH pressure line is for refrigerant going to the EVAPORATOR.
Both lines should be insulated. Insulate the low pressure side to keep the refrigerant a bit cooler going into the compressor and insulate the high pressure side to prevent the refrigerant from absorbing heat from the engine bay.
Your pipe insulation may melt (I don't know how hot this line gets) if you insulate the line going from the COMPRESSOR to the CONDENSER
low > compressor > condenser > high > evaporator > repeat
Ah crap! I knew I had the idea backwards. But....I am still getting colder air.
Side Note: It's a PIA to reach that high pressure line. If I can get some kind of reassurance that it'll make a significant difference, then by golly I'll grease up my body to squeeze in there if I have to.
texkidThread starterSugar Land, TX · Jun 26, 2009#19Update:
Yes, I had the circulation backwards.
However, I did some more research. Insulating the high pressure side will not improve cooling. Some mechanics sites say it'll do nothing....others say it'll put more pressure on the compressor, and blah, blah, blah.
Personally, I have not seen ANY positive results on insulating the High Side. In the meantime, I am going to research for insulation that withstand higher temps.
auxmikeLI, New Yawk · Jun 27, 2009#20Those foams you installed are in the vicinity of the very hot exhaust manifold.
212F is what water boils at. It's not really that hot when thinking in terms of an engine.
I'll pass on this one myself....😎
YarisSedanCalifornia - Bay Area · Jun 27, 2009#21A/C temp is directly affected by outside ambient temperature. So from different times of the day and different days you are going to get different results.
I get cars in my shop on extremly hot days saying thier ac is not cooling as efficently as before. But yet thier a/c is fully charged. So charging wont make a difference.
eTiMaGoBangkok, Thailand · Jun 27, 2009#22what an interesting idea, can certainly be useful here in our hot hot tropical days, the AC can really struggle sometimes...
I have a friend who works at an airconditioner repair workshop, maybe he can get his hands on the high-temp stuff 🙂
Sodium DuckWestern Mass. · Jun 27, 2009#23I just sent off some e-mails to companies about their mineral wool pipe insulation for pricing. I'm having trouble finding this stuff.
Sodium DuckWestern Mass. · Jun 27, 2009#24NiNjA pOsT!
CTScottUSA, CT · Jun 27, 2009#25Sodium DuckWestern Mass. · Jun 27, 2009#26Thanks Scott!
How long is this pipe by the way?
Hmm, that site has a 2'x4' sheet for 6 bucks, not bad.
mrbondIllinois · Jun 27, 2009#27Fantastic idea! I did this yesterday after I got home, except I used fewer zip ties and employed the use of aluminum tape. With the aluminum tape, the air temperature recorded on the meat thermometer was 37 degrees! Best cheap thing I've done to my car hands down.
Sodium DuckWestern Mass. · Jun 27, 2009#28Did you do both lines?
mrbondIllinois · Jun 27, 2009#29You mean the high pressure and low pressure? No, just the low pressure going into the cabin. My hands aren't small enough to work with the high pressure lines.
supmetSouthern California · Jun 27, 2009#30 Originally Posted by PK198105 ↑
rubber is the best insulator
Originally Posted by PK198105 ↑
Air is the best insulation.
The funny thing is, neither is "the best" insulator, or particularly good in the grand scheme of things.
texkidThread starterSugar Land, TX · Jun 27, 2009#31 Originally Posted by PK198105 ↑
here is what i did:
i covered the rear return line with high temp aluminium tape. Temp resistance up to 180C
Where did you find the aluminum tape? Was it easy to apply?
mrbondIllinois · Jun 27, 2009#32You can also find the aluminum tape at Menard's and Home Depot in the home ventilation section.
texkidThread starterSugar Land, TX · Jun 27, 2009#33 Originally Posted by PK198105 ↑
the local Rona in the vents and ac department. its like regular tape but with aluminium in it. very easy to apply. but gets pretty hot to the touch after you drive for a while
How's the air running? Same as with other setup? Or cooler?
texkidThread starterSugar Land, TX · Jun 27, 2009#34 Originally Posted by PK198105 ↑
haven't really got a chance to check, i got the aluminum foil mostly to protect the insulation from melting
Ah. I see. So far, mine hasn't melted. In fact, after doing some errands, I checked the insulation and it wasn't hot to the touch. But I did burn my left forearm from grazing the engine surface.......again.
EasyDriverSouthern Michigan · Jun 27, 2009#35I got half of this diy project done this PM and I believe that it helped already! At the only contact between the high and low pressure lines I slide a piece of thin aluminum pie tin. After a short drive today high pressure line was not even warm...but maybe I didn't drive long enough.
Great pics and a really good project!!!!! Thanks......
mrbondIllinois · Jun 27, 2009#36There's another section of the low pressure line pretty far down in the engine bay - right where the rubber hose ends and just before the a/c compressor. About an hour ago I spent about 20 minutes wrapping that in the foam insulator and the aluminum tape, then I drove the car for a while. The air temp dropped another degree. Just an fyi.
texkidThread starterSugar Land, TX · Jun 28, 2009#37 Originally Posted by
mrbond ↑ There's another section of the low pressure line pretty far down in the engine bay - right where the rubber hose ends and just before the a/c compressor. About an hour ago I spent about 20 minutes wrapping that in the foam insulator and the aluminum tape, then I drove the car for a while. The air temp dropped another degree. Just an fyi.
Sweet!
But keep an eye on it. Supposedly there might be a greater chance that section of the line could melt the insulation. If it doesn't over time then maybe I'll include in the DIY. I am still periodically checking my lines for excess heat or signs of damage/melting. Good thing I have a fire extinguisher in the car ready for anything.
texkidThread starterSugar Land, TX · Jun 28, 2009#38 Originally Posted by PK198105 ↑
...for now everything is a ok , except my nuts are frozen😁
For that you should use Glad ziplock bags to prevent freezer burn to your meat. I'll write a DIY for that as well. 😁 😁
1NZYaris1New Zealand · Jun 28, 2009#39 Originally Posted by PK198105 ↑
thats what i do for now , i check each time i arrive home just to be on the safe side. for now everything is a ok , except my nuts are frozen😁
😆 too much infomation , 😳 your nut's are not part of this thread ,
well they wheren't until now anyway 😆 😆 😆 😆🤮
texkidThread starterSugar Land, TX · Jun 28, 2009#40 Originally Posted by PK198105 ↑
i shall provide pictures.... i shaved no worries 😁
😆 ROTFLMAO!
darthbauerUSA · Jun 28, 2009#41This looks like something I should do but as of right now, I have no shade and its like over 100 here in Orange.
firebobon the road · Jun 28, 2009#42I keep looking at this and thinking about the way I covered my oil lines on my old truck. I split some “heater hose” slid it over the lines and use cheap electrical tape to cover it.
I have not thought about doing this and have not looked at the AC lines to see if this would work. But I do think it would look cleaner than what has been picked and what has been talked about.
darthbauerUSA · Jun 28, 2009#43 Originally Posted by PK198105 ↑
do what shave your balls or insulate the ac lines?? j/k
you can do it when the car is cold , it really takes about 10 minutes
The engine is cold as I have not gone anywhere in the last 24 hours in it, Its just to damn hot outside.
texkidThread starterSugar Land, TX · Jun 28, 2009#44 Originally Posted by
firebob ↑ But I do think it would look cleaner than what has been picked and what has been talked about.
I do agree that mine looks like it was "ghetto-rigged" but it is just a trial run. I am sure/hopeful that once it becomes established as a safe mod with reliable results that soon we'll start seeing some sophisticated modifications.
And as I said before, I am happy to post other user's pictures to replace mine. So long as they're clear images to reveal detail. Sorry, I don't like grainy, cell phone pics.
Originally Posted by
darthbauer ↑ The engine is cold as I have not gone anywhere in the last 24 hours in it, Its just to damn hot outside.
Yes, stay out of the sun. In the time I did this in the sun, my neck ended up with a little sunburn and I was dripping sweat on the engine.
What about those self-serve car washes where you have put quarters in and manually wash the car? Aren't those covered. I am sure if you go to one and do a quick install and maybe just rinse the car that they won't say anything.....maybe. Or one of those business parking garages?
WD-40Vancouver, Canada · Jun 28, 2009#45Thanks for the idea of aluminum foil tape .. I had the foam on last year for a trip to California .. made a huge dif .. then when I got home I removed it due to melting near the heat shield .. I just redid the lines but added the foil tape after reading this.
yarisugiハワイ · Jun 28, 2009#46Since the tape is a little flimsy and a bit hard to wrap around the pipe, has anyone wrapped the foam around first and then wrap the tape around the foam? I was thinking this might be better...?
texkidThread starterSugar Land, TX · Jun 28, 2009#47 Originally Posted by
yarisugi ↑ Since the tape is a little flimsy and a bit hard to wrap around the pipe, has anyone wrapped the foam around first and then wrap the tape around the foam? I was thinking this might be better...?
I think that was the original idea? 🤷
mrbondIllinois · Jun 28, 2009#48Yeah, that's actually exactly what I did: wrapped the foam around the a/c lines, zip tied them down, and then completely covered all the foam with the aluminum tape. At least this way you don't have to worry about the foam degrading faster than need be.
yarisugiハワイ · Jun 29, 2009#49I just went to Home Depot - that aluminum tape is pretty expensive eh?!!
It was rated up to 260 degrees F. Is there any that's higher? 260 doesn't seem high enough.
devinlamotheSudbury, Canada · Jun 29, 2009#50 Originally Posted by PK198105 ↑
its rated for direct contact , it should be fine for what we use them. its about 5$ here.
What ... I just went to Home Depot and the cheapest I found was $15. 🙁