Yarisworld Archive

DIY: A/C Insulation

218 posts · 298,753 views · page 2 of 5

Replies continued

mrbondIllinois · Jun 29, 2009#51
$15? Yeah, that sounds right for the foam aluminum wrapping. I got my huge roll of just the aluminum for $6.10 with tax.
hatchbackkid82. · Jun 29, 2009#52
I'm gonna have to try this
SandwashSo. Arizona, USA · Jun 29, 2009#53
With such an obvious improvement to effectiveness (and efficiency) of AC system you would think Toyota would develop a standardized 'fix,' provide a service bulletin to their dealerships, thus allowing them to bill their customary 'arm and leg' charges for those customers willing and able to go that route.
Yaris HiltonBristol, Tennessee, USA · Jun 29, 2009#54
Really!
texkidThread starterSugar Land, TX · Jun 30, 2009#55
Originally Posted by Sandwash ↑
With such an obvious improvement to effectiveness (and efficiency) of AC system you would think Toyota would develop a standardized 'fix,' provide a service bulletin to their dealerships, thus allowing them to bill their customary 'arm and leg' charges for those customers willing and able to go that route.
I agree.

I still want to assume that they probably NOT do this in order to save on building costs. Because if you look at the whole car itself, there isn't another part that is insulated. So I imagine that they probably thought "why purchase insulating foam (or other material) for one stretch of pipe" and just left it at that?
Pitt YarisPittsburgh · Jul 1, 2009#56
I'd like to do this. My a/c at a level 4 is no cooler than a friend's (old buick) a/c at a level 2.
Yaris HiltonBristol, Tennessee, USA · Jul 1, 2009#57
Well now, those old Buick ACs could be used to freeze a hockey rink. Probably draw off half the power the Yaris engine's capable of producing, too.
andacondaMontana · Jul 3, 2009#58
Originally Posted by hatchbackkid82 ↑
I'm gonna have to try this
That's what I said today!
So I took photos along the way.
1.wrapping_with_aluminum_tape.JPG2.entrance_to_cabin.JPG3.run_to_expansion_chamber_from_cabin.JPG4.expansion_chamber.JPG5.top_bend_near_alternator.JPG6.lower_part_from_compressor.JPG7.alternator_clearance.JPG
andacondaMontana · Jul 3, 2009#59
ran out of aluminum tape - will finish the job after the holiday...
yarisugiハワイ · Jul 3, 2009#60
Did the a/c cooling improve?
RedRideMiddletown, NY · Jul 3, 2009#61
Originally Posted by Sandwash ↑
With such an obvious improvement to effectiveness (and efficiency) of AC system you would think Toyota would develop a standardized 'fix,' provide a service bulletin to their dealerships, thus allowing them to bill their customary 'arm and leg' charges for those customers willing and able to go that route.
I've ony had my Yaris for a couple of weeks now, however it's becoming rapidly evident that Toyota left no stone unturned in its effort to cut cost to a minimum.

I'm not complaining as I wanted an inexpensive, no frills car. 🙂

As to why no TSB on this issue.... If they had one, that would be like admitting that there is a problem.
andacondaMontana · Jul 3, 2009#62
Originally Posted by yarisugi ↑
Did the a/c cooling improve?
Not sure yet, as I only checked for clearance with the insulation.
I did check my wife's Baja, and the sister-in-laws Aveo today - neither of them has any insulation whatsoever.

I can't see how this mod could possibly hurt anything at all! (other than a few cuts and bruises.)
auxmikeLI, New Yawk · Jul 3, 2009#63
Originally Posted by andaconda ↑
Not sure yet, as I only checked for clearance with the insulation.
I did check my wife's Baja, and the sister-in-laws Aveo today - neither of them has any insulation whatsoever.

I can't see how this mod could possibly hurt anything at all! (other than a few cuts and bruises.)
Yeah, looks like you hit something sharp! Mabye a glove would help prevent this for the others???
andacondaMontana · Jul 3, 2009#64
Originally Posted by auxmike ↑
Yeah, looks like you hit something sharp! Mabye a glove would help prevent this for the others???
Are you kidding me? I can't work with gloves. I get cut up if I even look at the underside of a car.

Besides that --- what's a little mod without a little blood?
texkidThread starterSugar Land, TX · Jul 3, 2009#65
Originally Posted by andaconda ↑
Are you kidding me? I can't work with gloves. I get cut up if I even look at the underside of a car.

Besides that --- what's a little mod without a little blood?
😆

That is definitely true. Besides, gloves were useless to me when I was smelling some burned arm hair.

Originally Posted by andaconda ↑
Not sure yet, as I only checked for clearance with the insulation.
If you don't mine, stick a meat thermometer in the air vent and let us know what temp you're getting when driving.

I noticed that mid-morning and after around 17:00 my temps go as low as 37-ish degrees.
firebobon the road · Jul 3, 2009#66
Originally Posted by andaconda ↑
Besides that --- what's a little mod without a little blood?
If there’s not blood then you didn’t do anything.



I truly don’t think there’s a big issue with the AC as it is stock. I have looked at other cars still sitting on the lot and they use metal lines that are not insolated for part of the run also. I have driven plenty of other cars, SUVs, and trucks but I think the Yaris is as good or better with it’s cooling capabilities. Could the problem start after mods have been done that changes the temp under the hood?

If you have your AC on and you’re not running the fan wide open then why run the compressor and make the motor work harder for no reason?
PatrickJohnsonMurfreesboro, TN · Jul 4, 2009#67
Originally Posted by firebob ↑
If there’s not blood then you didn’t do anything.



I truly don’t think there’s a big issue with the AC as it is stock. I have looked at other cars still sitting on the lot and they use metal lines that are not insolated for part of the run also. I have driven plenty of other cars, SUVs, and trucks but I think the Yaris is as good or better with it’s cooling capabilities. Could the problem start after mods have been done that changes the temp under the hood?

If you have your AC on and you’re not running the fan wide open then why run the compressor and make the motor work harder for no reason?
The cooling was good before, but after doing this mod and driving for about a week, it is a night and day difference.
Yaris HiltonBristol, Tennessee, USA · Jul 4, 2009#68
Your tetanus shots up to date, Andaconda?
firebobon the road · Jul 4, 2009#69
Originally Posted by PatrickJohnson ↑
The cooling was good before, but after doing this mod and driving for about a week, it is a night and day difference.
I’m sure there is a good difference in doing this. I’m just saying that with the car stock it is as good other stock cars that are on the market.
Sora65Brampton · Jul 4, 2009#70
Yeah im about to do this today. hopefully works out well.
Another question.
for the yaris sedan.. the one i have...

can you insulate passed the tube. like where the pipe line hits the compressor?
It kinda looks like a pain to do. but i like cold :)
andacondaMontana · Jul 4, 2009#71
If you don't mine, stick a meat thermometer in the air vent and let us know what temp you're getting when driving.
When I take it out of the garage on Monday, I'll take its temp.👍
andacondaMontana · Jul 4, 2009#72
If you have your AC on and you’re not running the fan wide open then why run the compressor and make the motor work harder for no reason?
Instead of turning the temp down or up, I'm in the habit of pressing the air "on/off" button so that the compressor will only come on when I want to cool off.
andacondaMontana · Jul 4, 2009#73
Originally Posted by Yaris Hilton ↑
Your tetanus shots up to date, Andaconda?
I don't believe I've ever had one???😲
andacondaMontana · Jul 4, 2009#74
Originally Posted by Sora65 ↑
Yeah im about to do this today. hopefully works out well.
Another question.
for the yaris sedan.. the one i have...

can you insulate passed the tube. like where the pipe line hits the compressor?
It kinda looks like a pain to do. but i like cold :)
Mine is the sedan too. It's easy to get to the pipe coming out of the compressor. Look at my second to last photo (on page 5 of this topic) of the pump itself.
AlexNet0Rockland, ME · Jul 4, 2009#75
so is there a general consensus as to what the insulating material should be? I dont want melting insulation.
andacondaMontana · Jul 4, 2009#76
Originally Posted by AlexNet0 ↑
so is there a general consensus as to what the insulating material should be? I dont want melting insulation.
As you can see on page 5 - the fifth photo down, I used copper pipe insulation that has about a 3/4 inch inner diameter. The insulation is about another 3/4 inch thick. I then wrapped it with aluminum tape for heat protection from the engine and exhaust manifold.
AlexNet0Rockland, ME · Jul 4, 2009#77
Originally Posted by andaconda ↑
As you can see on page 5 - the fifth photo down, I used copper pipe insulation that has about a 3/4 inch inner diameter. The insulation is about another 3/4 inch thick. I then wrapped it with aluminum tape for heat protection from the engine and exhaust manifold.
so the heat tape stopped the insulation from melting? I would think that it would still heat up inside, just not as much radiant heat would make it through the tape. Im just worried that the general ambient temperature due to the close proximity to the exhaust manifold will still melt the insulation under the tape.
firebobon the road · Jul 4, 2009#78
The aluminum tape will help the heat transfer. With a few layers of wrap it should help spread the heat out.
yarisugiハワイ · Jul 5, 2009#79
Almost completed this thing except for the alum.wrap near the pulley/engine mount - how
the heck do you wrap that area? I can't get my fingers and tape around there!!
andacondaMontana · Jul 5, 2009#80
Originally Posted by yarisugi ↑
Almost completed this thing except for the alum.wrap near the pulley/engine mount - how
the heck do you wrap that area? I can't get my fingers and tape around there!!
I cut out a section of the insulation to go around the mounting brackets and just used short pieces of tape rather that go a continuous wrap. Near the alternator, I didn't bother to wrap it at all.
I also offered a little blood to the 'engine bay gods' and that helped too.
Yaris HiltonBristol, Tennessee, USA · Jul 5, 2009#81
Originally Posted by andaconda ↑
I don't believe I've ever had one???😲
If you grew up in the U.S. since about the '50s, it's unlikely that you haven't had a primary tetanus immunization series. Required to go to school. But you're supposed to get a booster every 10 years, just in case you do stuff like gouge up your hands while working on your car. Lockjaw's bad stuff.

I suppose this is DIYer maintenance/service. :D
supmetSouthern California · Jul 5, 2009#82
Originally Posted by Yaris Hilton ↑
If you grew up in the U.S. since about the '50s, it's unlikely that you haven't had a primary tetanus immunization series. Required to go to school. But you're supposed to get a booster every 10 years, just in case you do stuff like gouge up your hands while working on your car. Lockjaw's bad stuff.

I suppose this is DIYer maintenance/service. :D
Hmmm, you are correct, the cdc website says DTaP is required across all 50 states, but I only remember getting tetanus shots post-injury. Maybe I just don't remember because its a combo vaccine for school requirements, and just a tetanus shots after injury.
texkidThread starterSugar Land, TX · Jul 5, 2009#83
Originally Posted by supmet ↑
Hmmm, you are correct, the cdc website says DTaP is required across all 50 states, but I only remember getting tetanus shots post-injury. Maybe I just don't remember because its a combo vaccine for school requirements, and just a tetanus shots after injury.
Rule of thumb is that if you don't remember your last DTaP shot then its time for booster.
AlexNet0Rockland, ME · Jul 5, 2009#84
Originally Posted by texkid ↑
Rule of thumb is that if you don't remember your last DTaP shot then its time for booster.
Lol, indeed.

Ive been lucky having cut myself, not so lightly, several times in the last two years, on not so clean metal, and havent had lockjaw yet, even though my tetanus is wayy overdue.
texkidThread starterSugar Land, TX · Jul 5, 2009#85
Originally Posted by AlexNet0 ↑
Lol, indeed.

Ive been lucky having cut myself, not so lightly, several times in the last two years, on not so clean metal, and havent had lockjaw yet, even though my tetanus is wayy overdue.
That's why its good for 10 years. 😉

Go ahead and treat yourself to a nice DTaP shot and enjoy the next 10 years of bumps, scrapes, and cuts. You know, the way God designed us to do. 😁
nth09Singapore · Jul 6, 2009#86
are those aluminum tape the same that we use in the kitchen? Or is it a sticky back tape?
yarisugiハワイ · Jul 6, 2009#87
^ It feels like aluminum foil that we use in the kitchen, but one side is sticky. That's why it's called aluminum tape.

I think I might have done a little overkill. On the back end, after wrapping with aluminum tape,
I had some Thermo-Tec Heat Shield left over and wrapped some more.
I think the Thermo-Tec can withstand the heat much better than the aluminum tape.
By the way, do you wrap that big bubble like thing in between the tube by the ECU? What is that for?

Picture lost · i279.photobucket.com
andacondaMontana · Jul 6, 2009#88
Originally Posted by texkid ↑
Rule of thumb is that if you don't remember your last DTaP shot then its time for booster.
Ah, come on now. Suck it up, and toughen yourselves up!
PatrickJohnsonMurfreesboro, TN · Jul 6, 2009#89
Originally Posted by yarisugi ↑
^ It feels like aluminum foil that we use in the kitchen, but one side is sticky. That's why it's called aluminum tape.

I think I might have done a little overkill. On the back end, after wrapping with aluminum tape,
I had some Thermo-Tec Heat Shield left over and wrapped some more.
I think the Thermo-Tec can withstand the heat much better than the aluminum tape.
By the way, do you wrap that big bubble like thing in between the tube by the ECU? What is that for?

Picture lost · i279.photobucket.com
If you read earlier in the thread, i think it's actually the original post, it says you don't have to cover that part, but that it does make a difference if you do. I don't have that part covered on my install, but only because I didn't have large enough material to do so, and i plan on doing it when i get back to the store.
texkidThread starterSugar Land, TX · Jul 6, 2009#90
Originally Posted by andaconda ↑
Ah, come on now. Suck it up, and toughen yourselves up!
My, my...

You can't really "toughen yourself" out of lock-jaw. In fact, that is the first sign that you should get treated. Why? I am glad you asked.....After your jaw locks up, your neck muscles and the muscles you use to facilitate in breathing begin to "lock-up". Once that happens, which are the late signs of a tetanus infection, you can't scream for help much less breathe effectively; putting you into respiratory arrest and then....well you get the rest.

Hence why it is important to be up to date with your vaccines. Besides, can you imagine what our friends will say? "Did you hear about 'so-and-so'? After he modified his car he died of tetanus. Who wants dibs on this car?" 😳

Originally Posted by yarisugi ↑
By the way, do you wrap that big bubble like thing in between the tube by the ECU? What is that for?
Honestly, I don't know what it is for. All I know is that it is wider and needs more material to wrap. It did make about a 3 to 5 degree difference when I wrapped it up. And yes, it was mentioned in my initial post.
texkidThread starterSugar Land, TX · Jul 6, 2009#91
Originally Posted by echo_hrs ↑
Just a few tidbits...I fear getting hit by a drunk driver head-on for the second time more than Tetanus...Fear of getting Tetanus from surface scratches caused by dirty or rusty parts (or stepping on a nail for that matter) is hugely overblown...
Oh hell yeah I fear more from a drunk driver or an idiot t-boning me at an intersection or getting mugged at gun point.

The point is that this is one measure that is preventable. There are still people I've met at the hospital that were in their 30 to 40's and still managed to contract Polio. POLIO for Pete's sake?! Cheese and Rice! That is another disease that could've be prevented. Yes, Polio and Tetanus are diseases that are more rare than car accidents. But no one wants to be that 1 person that contracted either of those, right?

Another case is that there are still kids in inner-city neighborhoods that are getting Lead poisoning. Another avoidable case. In 85% (my personal estimate) of those cases I came across, it was because the parents never thought that Lead was still on their walls! All they had to do when they moved in was just test the paint, strip the walls, and put on a fresh coat of lead-free paint that is available EVERYWHERE. But because of that same mentality in which Lead poisoning is so RARE nowadays, who would've thought that it would happen to their child?
andacondaMontana · Jul 6, 2009#92
Originally Posted by texkid ↑
😆

If you don't mine, stick a meat thermometer in the air vent and let us know what temp you're getting when driving.
Well I checked it on my 15min way home from work. Outside air not recycled air. Fan was on 2. Temp hung right around 40 degrees.
Temp increased to 42 degrees when I turned the fan on 4.

I wish I would have taken it's temp before the mod.
airtemp.JPG
andacondaMontana · Jul 6, 2009#93
I hope I didn't open a can of tetanus worms....
LazerdotEuless Texas · Jul 6, 2009#94
Did all but the area by the pullies. I put aluminum rap around the insulating foam and lightly tie wrapped the total. In my head ity seems cooler. Wish I had done a before after. But, can it hurt?
YarisSedanCalifornia - Bay Area · Jul 6, 2009#95
The only one thing keeping me from doing this mod. Is every pic i have seen looks way ugly!. I am trying to keep my engine bay looking show quality and clean.
CTScottUSA, CT · Jul 6, 2009#96
Originally Posted by YarisSedan ↑
The only one thing keeping me from doing this mod. Is every pic i have seen looks way ugly!. I am trying to keep my engine bay looking show quality and clean.
Instead of aluminum tape, use heat/flame resistant wire loom:

It even comes in blue, red and black.

http://www.summitracing.com/search/?...o%20flex&dds=1

cali yarisCanoga Park, CA · Jul 6, 2009#97
Here was a case where the tetanus vaccine made a lot of sense, as the soldiers were in a very hazardous environment with a high chance of contracting the disease. Do today’s children have the same odds?"
hmmm.... you should see my son's room
mikenacaratoBrentwood, TN · Jul 6, 2009#98
first off, i wanna say i love this idea!!!

second, how long until the evap core freezes over? i would put some a/c gauges on it every now and then to see what your low side pressure reading is, if you notice it dropping then your evap core is freezing up and will cause the system to shut off.
texkidThread starterSugar Land, TX · Jul 6, 2009#99
Originally Posted by mikenacarato ↑
first off, i wanna say i love this idea!!!

second, how long until the evap core freezes over? i would put some a/c gauges on it every now and then to see what your low side pressure reading is, if you notice it dropping then your evap core is freezing up and will cause the system to shut off.
I thought there were safety features that would prevent that? 🤷 I guess someone should keep an eye on it and let us if we screwed something or maybe tweak it a bit more.

Originally Posted by CTScott ↑
Instead of aluminum tape, use heat/flame resistant wire loom:

It even comes in blue, red and black.

http://www.summitracing.com/search/?...o%20flex&dds=1

That is an awesome idea. I imagine one must cut a slit in order to wrap around the lines?

Originally Posted by Lazerdot ↑
Did all but the area by the pullies. I put aluminum rap around the insulating foam and lightly tie wrapped the total. In my head ity seems cooler. Wish I had done a before after. But, can it hurt?
It should work. You be the judge. Does it feel cooler? I am noticing that I can now drive with the setting at (2) instead of the usual (3) or (4).


Originally Posted by andaconda ↑
Temp increased to 42 degrees when I turned the fan on 4.
I wish I would have taken it's temp before the mod.
I have been noticing that as well. I am assuming that it is only blowing the air faster without adjusting temperature to the A/C; essentially more quantity and less quality?

Nonetheless, it is not too bad since supposedly you get COLDER air when set to "recirculating".
RevssonSoutheast Wisconsin · Jul 7, 2009#100
Originally Posted by texkid ↑
That is an awesome idea. I imagine one must cut a slit in order to wrap around the lines?
That's what it tells you to do on the advertisement page. 😉

Much nicer looking than the silver wrap, IMO.