Replies continued
Henry G.So Cal. · Jul 7, 2009#101Did mine today. I zip tied the foam as I went from one end to the other, then twisted/adjusted the foam, re-tightened the zipties as necessary and cut the ends off. I found the aluminum tape at Home Cheapo, a small roll (50 yards!) was 7 bucks and change, I saw the larger roll it was almost $15, the small roll is enough to do 20 cars at least.
I rotated the zip tie buckles to the rear before taping. As Anaconda mentioned the hot tip is to cut short pieces of tape, approx 6 inches long and wrap one section at a time, I used about a 1/4" overlap, and double wrapped the area closest to the header. IMO the header is likely responsible for most the heat warming the line, so I just did the back section across the firewall, the rest is too curvy and complicated for a clean wrap.
Half way there:
Picture lost · i53.photobucket.com
Finished:
Picture lost · i53.photobucket.com
I will check the result and see if I can feel the difference later today.
Good thread and DIY thanks guys.
DageQuébec Canada · Jul 7, 2009#102It is not a good idea. theres a reason why toyota does not did that.
I work in refrigeration and climatisation.
The temperature of the air supply must never be lower than 50 degre F.
You need 20 degre F between the inlet and supply.
Your compressor will compress liquid refrigerant and its not good for longue time life.
without insulation, you gonna have better heat transfer for refrigerant vapor compress.
So, i don't think that is a good idea.
EasyDriverSouthern Michigan · Jul 7, 2009#103I used pipe insulation only on mine and also did the lower area by the compressor. For the area by the engine mount and alternator pulley I took a 3" x 4" piece of aluminum dryer vent, bent it half mooned shape, over the low pressure line and over the low pressure line. I kind of wedged it in place firmly.
I get cold air in under 3 minutes...my vent thermometer (thanks for the tip on finding that texkid!). I'm reading 38 degrees vent temperature. I did not have the thermometer before the project, but I know it was not nearly as cold.
What kind of vent temperature are those of you that have used the aluminum tape getting?
EasyDriverSouthern Michigan · Jul 7, 2009#104Correction: I took a 3" x 4" piece of aluminum dryer vent, bent it half mooned shape, over the low pressure line and over the high pressure line. I kind of wedged it in place firmly.
n00bCanada · Jul 8, 2009#105 Originally Posted by PK198105 ↑
ok...guess you didn't read properly what we did.we're not insulating the refrigerant as it enters the compressor but after its refrigerated so that it doesn't warm up when it goes back to the cabin.
both of you are incorrect.
The low pressure line is for refrigerant going to the compressor. It's a good idea to insulate the low pressure line to keep the refrigerant cool as it enters the compressor. The cool refrigerant helps cool down the compressor. The high pressure line goes into the cabin. The high pressure goes through the expansion valve making it a low pressure liquid and cold. The warm air passes through the evaporator and boils the refrigerant into a cold gas.
Why is it a good idea to insulate the high pressure line? Because you don't want your engine heat to warm up the cooled refrigerant that will be entering your cabin. From the pictures posted, it looks like the high pressure line is VERY close to the exaust manifold. Basically, your condenser is cooling the refrigerant, and a few feet later, your exaust is warming it back up again!
Seriously... just do a damn google search on how a/c works. The high pressure line is the one going to the evaporator, the low pressure line is the one going to the compresser.
yarisugiハワイ · Jul 8, 2009#106ok... what?
Just want to make sure I got this right. Wrap only the fat tube on the top. Leave the skinny tube alone. Correct?
n00bCanada · Jul 8, 2009#107 Originally Posted by
yarisugi ↑ ok... what?
Just want to make sure I got this right. Wrap only the fat tube on the top. Leave the skinny tube alone. Correct?
That's your choice. Wrap both if possible.
andacondaMontana · Jul 8, 2009#108Man, I'm I getting confused now...
Yaris HiltonBristol, Tennessee, USA · Jul 8, 2009#109Might be the tetanus setting in...
LafiroNYC · Jul 8, 2009#110I thought about this weeks ago and wanted to post this, but school and work and internship and other jobs are taking my life over.
Now that I see lots are doing this little trick, I will be going today to buy myself that foam.
Question is, what size diameter did you buy? Maybe home depot is a good place to buy it?
Thanks!
n00bCanada · Jul 8, 2009#111 Originally Posted by PK198105 ↑
no need to wrap the second one , there is no point in wrapping it since the system needs to be hot on that side for the loop.
http://www.energyquest.ca.gov/how_it...nditioner.html When the working fluid leaves the condenser, its temperature is much cooler and it has changed from a gas to a liquid under high pressure. The liquid goes into the evaporator through a very tiny, narrow hole. On the other side, the liquid's pressure drops. When it does it begins to evaporate into a gas.
I guess you should just bypass the condenser then! 🙄
Originally Posted by
andaconda ↑ Man, I'm I getting confused now...
The low pressure line is for refrigerant flowing to the compressor. The high pressure line is for refrigerant flowing into the cabin.
LafiroNYC · Jul 8, 2009#112Off topic, but where in the world is the part that is growing mold and causing my air to stink really bad and give me breathing problems now?
Someone please help me with that because I have to fix this issue. Since today I am free and having major problems installing my fog lights, I can not go to the dealership. Already tried calling and they are having phone problems.
EasyDriverSouthern Michigan · Jul 8, 2009#113b_hickman11Tyler, TX · Jul 8, 2009#114 Originally Posted by
Lafiro ↑ Off topic, but where in the world is the part that is growing mold and causing my air to stink really bad and give me breathing problems now?
Someone please help me with that because I have to fix this issue. Since today I am free and having major problems installing my fog lights, I can not go to the dealership. Already tried calling and they are having phone problems.
It has nothing to do with the cabin air filter.
Henry G.So Cal. · Jul 8, 2009#115Ok, with limited knowledge of the complexities of A/C system but with a brain and sense of touch this is easy: The big line (marked "L" on the fill/drain valve cap) is ICE COLD with the A/C on, the little line (marked "H" on the fill/drain valve) is hot. That tells me simply that it is THE BIG LINE that needs to be insulated as long as we agree the goal is to get COLD AIR from the A/C!
Try and argue that......
BTW I noticed a small but definite improvement from the wrapping I did yesterday so I will continue to do some more wrapping today....
n00bCanada · Jul 8, 2009#116 Originally Posted by
Henry G. ↑ Ok, with limited knowledge of the complexities of A/C system but with a brain and sense of touch this is easy: The big line (marked "L" on the fill/drain valve cap) is ICE COLD with the A/C on, the little line (marked "H" on the fill/drain valve) is hot. That tells me simply that it is THE BIG LINE that needs to be insulated as long as we agree the goal is to get COLD AIR from the A/C!
Try and argue that......
BTW I noticed a small but definite improvement from the wrapping I did yesterday so I will continue to do some more wrapping today....
If the goal is to get colder air, you want to insulate both if possible. From the pictures posted, it looks like you can insulate the high pressure line where the exaust manifold is (that would be an important place to insulate since it's so close to a heat source).
The high pressure line should not be hot (with the exception being the line from the compressor to the condenser) or that means your condenser is not cooling the refrigerant.
http://movacs.com/How%20it%20works/index.html 
n00bCanada · Jul 8, 2009#117 Originally Posted by PK198105 ↑
basically you want to keep whats cool cooler and whats warm warmer
Then Denso
failed by making a better condenser that cools the refrigerant even more!
http://www.globaldensoproducts.com/c...condenser.html Picture lost · www.globaldensoproducts.com mikenacaratoBrentwood, TN · Jul 8, 2009#118n00b why dont you either leave or properly introduce yourself in the welcome forum. do you even drive a yaris? your just starting crap we dont need. all of your posts have been in this 1 thread. im sure they have a forum out there that discusses stuff you have found on google and wikipedia...
Henry G.So Cal. · Jul 8, 2009#119Good post and diagram PK.
I just decided with that roll of tape there I would finish the job and wrap everything on the big line (notice I'm staying out of the technical argument by not naming it):
Picture lost · i53.photobucket.com
Wrapped the "can" portion of the line by taking two pieces of equal length insulation and doing the zip tie/tape thing.
Picture lost · i53.photobucket.com
Did the piece of line that runs against the inner fender, kind of a pain. I found the trick was to cut the piece to the right length, take it back off, install 2 already looped(just barely so as to leave the maximum room) on the pipe, put the insulation back on then wiggle the zip tie loops over either ends and then tighten them.
Picture lost · i53.photobucket.com
After that section this one was easy, I used tape again even though I dont think heat is a concern way up front but because I figure the engine bay heat in general is likely to harden the zip ties quickly making them brittle and breaking them, so the tape was more of a securing thing.
Picture lost · i53.photobucket.com
And this pic is from under the car, this section of pipe is easier to do most of the work from under the car believe it or not. Same thing zip tie and tape.
n00bCanada · Jul 8, 2009#120 Originally Posted by
mikenacarato ↑ n00b why dont you either leave or properly introduce yourself in the welcome forum. do you even drive a yaris? your just starting crap we dont need. all of your posts have been in this 1 thread. im sure they have a forum out there that discusses stuff you have found on google and wikipedia...
To answer your's and PK198105's question of driving a Yaris, I do not. I drive an Echo (which has crappier a/c than the Yaris).
I don't feel like posting in the welcome forum. I've never done that on any of the forums I am a member of.
Sodium DuckWestern Mass. · Jul 8, 2009#121Hence your user name... newbert.
talnlnkySpokane, Wa · Jul 8, 2009#122you all make this way too hard.
1)The cooler the hot side, the cooler the cold side, which means the cooler the air will be.
2)The cooler you can keep the cold side before it reaches the cabin, also the cooler your air will be.
The high temp loam plus high temp/fire retardant foam is what I would use too. That, or I think i've seen hi-temp split rubber tubing before.
b_hickman11Tyler, TX · Jul 8, 2009#123Does anyone know the longterm effects this mod will have on the AC components? This sounds like a good mod for the time being but will this cause the dryer or the Evap or other parts to go out at a faster rate? Sounds like this mod will create more water in the air which will cause the parts to work harder. Maybe even causing an increase in mildew build up which is already an issue with the stock system.
n00bCanada · Jul 8, 2009#124 Originally Posted by
b_hickman11 ↑ Does anyone know the longterm effects this mod will have on the AC components? This sounds like a good mod for the time being but will this cause the dryer or the Evap or other parts to go out at a faster rate? Sounds like this mod will create more water in the air which will cause the parts to work harder. Maybe even causing an increase in mildew build up which is already an issue with the stock system.
There are no long-term effects other than a better working a/c.
CTScottUSA, CT · Jul 8, 2009#125It shouldn't cause any issues. Normally with an AC system you insulate the suction side if the system is cooling only, and both suction and discharge if it is a reverse cycle system (i.e heat pump).
The Yaris's AC amplifier (ecu for the AC system) has temperature and pressure sensors to keep it from killing the compressor if the coils freeze up. Also, I don't think that this could cause the system to suddenly become so efficient that it can't dehumidify the air before reaching the desired inside temp (like a severely over-sized central air system in a house). I haven't seen the inside of the airbox, but the mold and stink issue is probably being caused by the condensate not properly draining (or maybe soaking into an insulation material within the box). This could explain why the TSB involves replacing the airbox.
EasyDriverSouthern Michigan · Jul 8, 2009#126I got mine at Home Depot in the plumbing department. $1.38 for a 6 foot piece....all you'll need and then some. I thought I got the 1/2 inch ID, but I just measured a left over piece and it was 1 3/8 OD and 3/4 ID. I got the zip ties at Wallyworld, the 100 pack in the automotive area was less than $3...fortunately I didn't need a 100 though!
Good luck!
EasyDriverSouthern Michigan · Jul 8, 2009#127How you ever managed to get zip ties in the area near the alternator (picture 2) is beyond me! I tried and tried to do that, but couldn't get it done. Or, maybe my patience just ran out!
mikenacaratoBrentwood, TN · Jul 8, 2009#128 Originally Posted by
n00b ↑ There are no long-term effects other than a better working a/c.
evap core freezing up......
n00bCanada · Jul 8, 2009#129 Originally Posted by PK198105 ↑
wikipedia told you this?
Thanks, I'm done with this forum. I'll let you believe 2+2=5.
LafiroNYC · Jul 9, 2009#130Now im trying to figure out if the cold line we are feeling on the top of the exhaust/left of the motor is actually going into the cabin, or coming out?
The pictures above show it coming out, meaning what is the point to keep something cool thats not going to the cabin to make us cool!?
Someone has to explain this better, or maybe there is another place to insulate this?
Also has anyone looked under the steering wheel, right side of the floor, and also seen how close the two pipes come to each other? Seems like that needs insulation as well!
LafiroNYC · Jul 9, 2009#131Yes, that explination worked out great. Thanks.
I will try doing this tomorrow, couldn't today because I was in the process of installing fog lights.
mikenacaratoBrentwood, TN · Jul 9, 2009#132 Originally Posted by PK198105 ↑
that would be the case if we insulate the HIGH PRESSURE line.
the compressor might not have to work so hard, neither your fan so i would say that long term effects would be beneficial.
ah, well then ill take your work on it. i have some heat shielding tape im going to use i just wanted to make sure the core wouldnt freeze. 🎉
EasyDriverSouthern Michigan · Jul 9, 2009#133If anyone is concerned about the core freezing up....simply don't cover the entire line. It won't be as cold in the cabin, but you don't have to worry about it. If you covered the entire line, like I did, all you have to do is remove some of the insulation and the problem is solved.
texkidThread starterSugar Land, TX · Jul 9, 2009#134 Originally Posted by
EasyDriver ↑ How you ever managed to get zip ties in the area near the alternator (picture 2) is beyond me! I tried and tried to do that, but couldn't get it done. Or, maybe my patience just ran out!
Patience and a needle nose pliers to use as my second fingers. But mainly patience. 😁
b_hickman11Tyler, TX · Jul 9, 2009#135 Originally Posted by
n00b ↑ There are no long-term effects other than a better working a/c.
How many years have you had this mod?
b_hickman11Tyler, TX · Jul 9, 2009#136What does the dryer do?
CTScottUSA, CT · Jul 9, 2009#137 Originally Posted by
b_hickman11 ↑ What does the dryer do?
The dryer removes moisture that may have entered the system to protect the compressor.
b_hickman11Tyler, TX · Jul 9, 2009#138 Originally Posted by
CTScott ↑ The dryer removes moisture that may have entered the system to protect the compressor.
So....I would assume that the dryer has some type of rating on it, meaning the amount of moisture it can remove out of the air in a given amount of time. With this new mod, more moisture will be present in the line. How do we know that the dryer will do it's job with the extra moisture. It might work for now, but a year from now, or 2, or 3, will it still be able to work correctly or will it break prematurely due to having to work harder?? Anyone have any longterm data?
toastNappanee, IN · Jul 9, 2009#139 Originally Posted by
b_hickman11 ↑ So....I would assume that the dryer has some type of rating on it, meaning the amount of moisture it can remove out of the air in a given amount of time. With this new mod, more moisture will be present in the line. ?
The drier will trap moisture and debris that entered the system when it was assembled and charged. As the a/c system is a sealed system you will not be getting any new moisture in the lines until a leak develops and then you have a whole new problem... no cooling. If you replace a compressor you change the drier too.
b_hickman11Tyler, TX · Jul 9, 2009#140 Originally Posted by
toast ↑ The drier will trap moisture and debris that entered the system when it was assembled and charged. As the a/c system is a sealed system you will not be getting any new moisture in the lines until a leak develops and then you have a whole new problem... no cooling. If you replace a compressor you change the drier too.
So whats the point of a dryer?? The way you describe it is that once it dries the initial moisture in the air when the AC is used for the very first time, then dryer is useless?
CTScottUSA, CT · Jul 9, 2009#141 Originally Posted by
b_hickman11 ↑ So whats the point of a dryer?? The way you describe it is that once it dries the initial moisture in the air when the AC is used for the very first time, then dryer is useless?
It has the ability to absorb a significant amount of moisture - more than should be in the system from initial manufacturing. Once the system leaks enough to reach atmospheric pressure the dryer will most likely become saturated. Replacing the dryer, when replacing the compressor is important, since you can't easily tell the condition of the dryer and it is cheap in comparison to the compressor.
b_hickman11Tyler, TX · Jul 9, 2009#142 Originally Posted by
CTScott ↑ It has the ability to absorb a significant amount of moisture - more than should be in the system from initial manufacturing. Once the system leaks enough to reach atmospheric pressure the dryer will most likely become saturated. Replacing the dryer, when replacing the compressor is important, since you can't easily tell the condition of the dryer and it is cheap in comparison to the compressor.
So why wouldn't they come up with a machine that dry's out the system at the factory and not install a dryer since the dryer is useless after becoming saturated from the moisture in the lines during installation. Wouldn't that be more green for the economy??
CTScottUSA, CT · Jul 9, 2009#143When you charge an AC system, you first draw a vacuum on it to pull out as much moisture and particulate as possible. It's impossible to get every bit, so that's where the dryer comes into play.
b_hickman11Tyler, TX · Jul 9, 2009#144 Originally Posted by
CTScott ↑ When you charge an AC system, you first draw a vacuum on it to pull out as much moisture and particulate as possible. It's impossible to get every bit, so that's where the dryer comes into play.
Thats why they need to have a removable dryer. Has a shut off valve before and after the dryer. After the dryer has done it's job, shut the valves off and remove the dryer. Clean the dryer out and reuse it on the next car coming down the belt.
MadMaxSan Antonio, Texas! · Jul 10, 2009#145 Originally Posted by
b_hickman11 ↑ How many years have you had this mod?
That's the rub, no one has had this done on their cars for more than a couple of weeks; so if there are any adverse long-term effects, no one knows!
I might be crazy, but I simply never run the a/c in my Yaris even with the triple-digit temps we've been having for the past month or so. I also drive an open Jeep, so maybe I am used to it, or I've killed all the brain cells that would've told me I am nuts; but since I most drive on freeways without a lot of stops on my commute, the two windows down method keeps me comfortable enough...and it sure feels great when I walk into the air conditioned house! 🎉
Cheers! M2
b_hickman11Tyler, TX · Jul 10, 2009#146 Originally Posted by
MadMax ↑ That's the rub, no one has had this done on their cars for more than a couple of weeks; so if there are any adverse long-term effects, no one knows!
I might be crazy, but I simply never run the a/c in my Yaris even with the triple-digit temps we've been having for the past month or so. I also drive an open Jeep, so maybe I am used to it, or I've killed all the brain cells that would've told me I am nuts; but since I most drive on freeways without a lot of stops on my commute, the two windows down method keeps me comfortable enough...and it sure feels great when I walk into the air conditioned house! 🎉
Cheers! M2
I already knew the answer to the question. I was just trying to figure out how he knew that there were NO longterm effects.....
Henry G.So Cal. · Jul 12, 2009#147Drove into town yesterday, around 100 degrees the AC is definitely colder. So I call this one a success. If the AC breaks for some reason in the future (I doubt it) I will take 5 minutes and cut the stuff off before taking it to the dealer so they don't have a (weak) reason to refuse the warranty claim.
b_hickman11Tyler, TX · Jul 12, 2009#148 Originally Posted by
Henry G. ↑ Drove into town yesterday, around 100 degrees the AC is definitely colder. So I call this one a success. If the AC breaks for some reason in the future (I doubt it) I will take 5 minutes and cut the stuff off before taking it to the dealer so they don't have a (weak) reason to refuse the warranty claim.
You have the basic warranty or extended?
Henry G.So Cal. · Jul 13, 2009#149Got the "Gold" 100k warranty for $299. The finance guy started at $599 I said no until he got to $299. I said "I thought these Toyotas were supposed to be reliable is there something youre not telling me?"
Hard to sell one one of the most reliable cars on the market then convince you you should get the extended warranty don't you think?
LafiroNYC · Jul 13, 2009#150So I took a digital thermometer and at a standstill in the shade the temperature goes to around 42f. And when I drive it goes to a low and steady 35f. The temperature outside was 78f. This was done with the fan on 2.
I will be wrapping the pipe today hopefully and will let everyone know what happens.