I got some large size heater core tubing (that rubber stuff that connects your radiator to your motor. Going to wrap the AC pipe with foam, then cover the foam with this rubber tubing. Its oil/fluid resistant, and also hi-temp. Should work well, and the dull black color should make it look fairly stock/stealth.
DIY: A/C Insulation
218 posts · 298,753 views · page 4 of 5
Replies continued
Take pics and post 'em!Originally Posted by talnlnky ↑I got some large size heater core tubing (that rubber stuff that connects your radiator to your motor. Going to wrap the AC pipe with foam, then cover the foam with this rubber tubing. Its oil/fluid resistant, and also hi-temp. Should work well, and the dull black color should make it look fairly stock/stealth.
Cheers! M2
will do... might not be till next week... I got soccer tonight so I probably wont pick up the foam until tomorrow... and then to make sure it looks nice I want to take my time... so my work will most likely be slow.Originally Posted by MadMax ↑Take pics and post 'em!
Cheers! M2
I'll be cutting a slit down the tube (think split loom) and then either zip tie it closed... or better yet... maybe silicone sealant.
ok... started working on this... The rubber heater core tube fits perfectly over the pipe.... except when the pipe bends. Going to stop by home depot or lowes on the way back to see if I can find a thin type of foam to cover the pipe. There are a few corners which which are too tight for me to get the hose to bend around, so I'll have to cut weird wedges to cover the corners. Then i'll just have to wrap black electric tape neatly around that to make it stay in place well. Even if I don't find anyfoam... I'm sure the rubber heater core tubing will insulate it fairly well. Will post pics when i'm done.Originally Posted by talnlnky ↑will do... might not be till next week... I got soccer tonight so I probably wont pick up the foam until tomorrow... and then to make sure it looks nice I want to take my time... so my work will most likely be slow.
I'll be cutting a slit down the tube (think split loom) and then either zip tie it closed... or better yet... maybe silicone sealant.
I am not sure if the mod will benefit you. If you're already getting 35-degrees then thats not too bad. Of course, NYC is around 78-degrees whereas Houston is running around high 90's. That can make a difference between A/C.Originally Posted by Lafiro ↑So I took a digital thermometer and at a standstill in the shade the temperature goes to around 42f. And when I drive it goes to a low and steady 35f. The temperature outside was 78f. This was done with the fan on 2.
I will be wrapping the pipe today hopefully and will let everyone know what happens.
Who knows, maybe the mod will drop yours down to 33-degrees!
Ill be honest, I wrapped mine up in fiberlass(dads idea), and then aluminum tape, and it did pretty much Nothing to lower the temps.
Im about to remove it cause its a messy look. I will go the foam route though soon.
And like I said, it only drops to that temp at the lowest. Usually when the car is moving, and the compressor is active, it will drop to the upper 30's. And as soon as the compressor stops, it can go as high as 47degrees. If the car is sitting doing nothing, it will go between 40 and 47degress. This is all in farenheit.
Im about to remove it cause its a messy look. I will go the foam route though soon.
And like I said, it only drops to that temp at the lowest. Usually when the car is moving, and the compressor is active, it will drop to the upper 30's. And as soon as the compressor stops, it can go as high as 47degrees. If the car is sitting doing nothing, it will go between 40 and 47degress. This is all in farenheit.
Hmmm...I guess do try the foam approach. But even hi-30's with no insulation seems about fair. You tell me, what's considered hot weather in NYC? Do you do a lot of stop-and-go traffic or are you actually able to cruise a longer periods? Because if mid-80's is about average and since the our A/C systems vary according the the weather and driving conditions, you might be able to get that sucker down to 35-ish?Originally Posted by Lafiro ↑Ill be honest, I wrapped mine up in fiberlass(dads idea), and then aluminum tape, and it did pretty much Nothing to lower the temps.
Im about to remove it cause its a messy look. I will go the foam route though soon.
And like I said, it only drops to that temp at the lowest. Usually when the car is moving, and the compressor is active, it will drop to the upper 30's. And as soon as the compressor stops, it can go as high as 47degrees. If the car is sitting doing nothing, it will go between 40 and 47degress. This is all in farenheit.
Heck, anyone from Arizona or New Mexico try this mod and still get colder air? 😁
It ranges, the past couple of days have been 78-84degrees. And the temperature remains around the same levels.
Now thats a silly question about cruising, or stop and go. Where do I live? lol Its all stop and go, even the highways 80% of the time.
Now thats a silly question about cruising, or stop and go. Where do I live? lol Its all stop and go, even the highways 80% of the time.
😆Originally Posted by Lafiro ↑
Now thats a silly question about cruising, or stop and go. Where do I live? lol Its all stop and go, even the highways 80% of the time.
Sorry, never been to NYC. In Houston, San Antonio, and Dallas, yeah there is primarily stop-and-go traffic but once you get a bit of the ways out, you can fly at 70mph without a problem. LoL!
Let us know what are the results after the foam approach.
well, since the heater tube didn't bend as well as I had hoped for I had to use more electrical tape, and make more pieces of tube than I had wanted. So, it doesn't look as nice as I was hoping, but it still looks decent. I also ended up deciding to go without any foam.
The electrical tape is good to 220 degrees F, and the tubing i'd think would be good to at least 300 F. The tubing is fairly thick, so I don't think foam is necessary.
Yesterday I was able to finish the first lil curved pieced located near the radiator before the fiance got home. Will try and finish the rest tonight.
I won't have numbers on mine, since I only use AC about every two months when I do a 1000 mile trip. If nothing else, wrapping it in rubber tubing should help protect the pipes from corrosion or any damage from happening to them.
The electrical tape is good to 220 degrees F, and the tubing i'd think would be good to at least 300 F. The tubing is fairly thick, so I don't think foam is necessary.
Yesterday I was able to finish the first lil curved pieced located near the radiator before the fiance got home. Will try and finish the rest tonight.
I won't have numbers on mine, since I only use AC about every two months when I do a 1000 mile trip. If nothing else, wrapping it in rubber tubing should help protect the pipes from corrosion or any damage from happening to them.
That's an interesting point. If you wrap it in foil tape, it keeps water out. But if its just foam and zip ties like most people, I wonder if there is a chance of it actually increasing corrosion, giving the water somewhere to sit touching the pipe, rather than just hitting the pipe and evaporating or just sliding off.Originally Posted by talnlnky ↑I won't have numbers on mine, since I only use AC about every two months when I do a 1000 mile trip. If nothing else, wrapping it in rubber tubing should help protect the pipes from corrosion or any damage from happening to them.
well... moisture will only foam where there is air present, so, if the foam is perfectly on the pipe with no gaps or pockets for air, there will be no moisture. That's not practical however.Originally Posted by supmet ↑That's an interesting point. If you wrap it in foil tape, it keeps water out. But if its just foam and zip ties like most people, I wonder if there is a chance of it actually increasing corrosion, giving the water somewhere to sit touching the pipe, rather than just hitting the pipe and evaporating or just sliding off.
Another point tho.... moisture will only form where there is a significant change in temperature.... gotta drop the temp below the dewpoint with the given humidity....so, even if there are pockets of air under the foam, if the foam is insulating well from the outside, it still shouldn't be much of an issue.
I'm not a huge fan of using the foam simply for fire/heat issues.... and covering it up with that aluminum tape.... ehhh... looks ugly I think. I'm sure foam and tape however will be a better insulator than what i'm doing. I however don't really have much of a complaint with my ac to begin with... but figure this will help some, and on long trips, this might help me keep the AC off a bit more... thus increasing mpg's. Total weight added will be less than a pound too.
👍
finished over the weekend.... don't have net at home anymore.... neighbors moved out... will take pics and try to upload them at work sometime this week. Using electrical tape was a pita because of the hot line that runs very close to the cold line getting in the way. I can see why the original poster used zip ties. I'm also sure that foam would work better than heater core tubing like I used... tho, not nearly as safe (I don't have to worry about high temps or hot liquids).
don't have net at home anymore.... neighbors moved out.LOL - you were "borrowing" internet access?
I prefer the term looting... maybe even stealing. Don't worry, I was all ninja about it... they didn't know.Originally Posted by cali yaris ↑LOL - you were "borrowing" internet access?
Originally Posted by texkid ↑First off, I really should THANK Echo-hrs for the idea. If he never mentioned in the first place, I probably would've never know to do this to my car. I went to my mechanic for some help. After taking a look at my car, he definitely agreed that the Low Pressure line needed to be insulated.
I purchased a meat thermometer to get a reading on how its running BEFORE I started doing the insulation. Below is the reading with the A/C set to (4) on Recirculating, with all vents open; driving from work to home (roughly 20 minutes) ABOUT 50-DEGREES
Here is temp, with the car in the drive-way and windows half open. Its 120-freaking-degrees!
AND FINALLY, here is the temp AFTER the insulation driving for 15 minutes. A DROP OF ALMOST 10-DEGREES!
So, without further delay, on with the DIY.
Disclaimer: I am not responsible for what happens to your car. Do this at your own risk.
Tools:
- A pack of foam pipe covers (.75 cents at Wallmart)
- A pack of 6 inch wire ties or whatever you call them
As far as the zip ties are concerned, DO NOT tie them too tight like I did. Just enough tension to keep them in place is all that is needed.
- A meat thermometer
- A couple bottles of water
- SHADE!
Instructions:
Lets start with what the hell we are insulating. It is the low pressure line going from the firewall to the rubber hose before it hits the condensor. Its marked with a pink line at the firewall and has a pressure valved labeled "L". When run the A/C, this line should be the only one that is COLD to the touch. The smaller line that sits below it should be open to air as it is taking hot air out of the cabin and back to the condenser.
next: get your foam pipe insulation and check to see if it fits. If its too loose, you can trim off a bit. But just a BIT!
-Start at the firewall end since it is most difficult and cramped part of the job. At this point, it is recommended that the engine is cool to touch. I singed a couple of arm hair before I realized that. LOL!
-Run it as much as you can, once you hit that big, "drum" looking thing, cut and start tying it down. As far as that "drum" looking thing, you're just going have to get creative and find a way to cover it. But it does make a difference when you do.
As far as the zip ties are concerned, DO NOT tie them too tight like I did. Just enough tension to keep them in place is all that is needed.
-For the other side, grab a piece and run it from the front side and thread it under the engine mount. Tie that down very well and make sure nothing can hit the belt or the alternator.
-For the rest of the low pressure line, just keep tying it down until you hit the rubber hose. I shouldn't have to tell you this, but cut holes where needed such as the low pressure valve and that do-hicky you see below.
-AND YOU'RE DONE! Cut off the excess straps so they won't get tangled into anything.
Ok so it's been almost a year since this thread was made.
Anyone found / notice and negatives to doing this? Has it really made a difference in a/c efficiency?
Yep it definitely works. I used the aluminum tape over the foam and zip ties and its all still holding together nicely. Check the clearance at the back of the motor between the exhaust manifold and AC line (when the cars cool), its about an inch and half. Does that make sense? No!!
I read this thread and decided it was a good "investment" Mod so here you can see what the result was....
I used The Wiring Loom instead of aluminum for cosmetic reasons and wanted the engine bay to look a little neater... The loom has not degraded or shown any signs of overheating, so mybe it will last....(hopefully)
There is enough of it in the engine bay already so it should do fine.
The DIY results were as good as I expected.
You can see the final result at this link:http://www.scikotics.com/forums/showthread.php?t=192547
Aloha From Hawaii !
I used The Wiring Loom instead of aluminum for cosmetic reasons and wanted the engine bay to look a little neater... The loom has not degraded or shown any signs of overheating, so mybe it will last....(hopefully)
There is enough of it in the engine bay already so it should do fine.
The DIY results were as good as I expected.
You can see the final result at this link:http://www.scikotics.com/forums/showthread.php?t=192547
Aloha From Hawaii !
On the Pro side it will help fuel economy because the compressor is a variable compression design as most are these days. On the con side if you were over charged and running AC on a cool day you would let liquid refrigerant into your compressor producing hydrostatic lock. When I do mine I will use aluminum tape over the insulation to reflect heat away from the insulation. That makes it way harder to melt the cheap insulation with under hood heat. The other hyper-miler tip here in Phoenix is to tint the windows. Both this insulation and window tint will cut the mileage drain AC caused here in Lucifer's waiting room. Window tint alone reduces the fan setting you have to use to wear a suit when the outside air temp on the express way says 1198 degrees F. I get 39 MPG here at 65 MPG on cruise lock. I've been watching for a trick to break 40 under the same harsh conditions. I average 42 city and highway so hyper-mile tricks between lights does work. Our winter mileage is even better than that. From my sig you can also see the other mods that allow better than EPA mileage results.Originally Posted by IsLNdbOi ↑Ok so it's been almost a year since this thread was made.
Anyone found / notice and negatives to doing this? Has it really made a difference in a/c efficiency?
You don't want to insulate the High pressure line. Doing so will cut the sub-cooling of the High pressure liquid returning from the condenser and will decrease efficiency and mileage as a consequence.Originally Posted by texkid ↑Update:
Yes, I had the circulation backwards.
However, I did some more research. Insulating the high pressure side will not improve cooling. Some mechanics sites say it'll do nothing....others say it'll put more pressure on the compressor, and blah, blah, blah.
Personally, I have not seen ANY positive results on insulating the High Side. In the meantime, I am going to research for insulation that withstand higher temps.
I think if it would make a big improvement, the factory would've already done it.
That's why I hesitated and waited so long to do it... My thoughts were like yours. However, summer heat is just around the corner, and a FEW degrees make a big difference when you're just above the "comfort zone" temp wise...Originally Posted by Yaris Hilton ↑I think if it would make a big improvement, the factory would've already done it.
My Co-Worker was also skeptical, but after we went to lunch in my car, he decided to do it on his Tacoma as well, and even on his wife's car too. We FELT and SAW the difference and figured it could translate into a better fuel effeciency rating if the compressor would not kick in as often.
At any rate, I like the feel of the colder air blowing on my face while I sit in traffic, waiting to move 15 feet more before the light changes.... LOL
Yeah, any improvement's a good thing. Gridlock in summer is grim without AC. Especially when straddling a big air cooled Harley engine.
Just did it to my car over the weekend and I notice a small difference. It is in the high 80's so I will check after this week and see how it does. Fairly easy to do.
funny i just did this several hours ago. lol took like 30mins. i thought it worked well. worth the whole $2 in supplies i used.
Where can I get the supplies to do this?
To share my DIY..mine is yaris sedan












I'll be trying this out this afternoon and probably taking video of the process, if anyone would find that useful. Here's hoping the shade is enough to stave off the 100 degree heat...
Video DIY's are always welcome!Originally Posted by Echostatic ↑I'll be trying this out this afternoon and probably taking video of the process, if anyone would find that useful. Here's hoping the shade is enough to stave off the 100 degree heat...
anyone try headerwrap and speed tape? the aluminum ducttape? thinner, probably better insulator with the shiney tape...and you know it wont catch fire lol.
i think i'll get some header-wrap and see for myself.
i think i'll get some header-wrap and see for myself.
I just did this, after finding this thread today.
$1.92 at Lowes for 6 feet of self-adhesive 3/4" Inside Diameter tube.
$3.19 at Walmart for 200F duct tape (low quality, but will probably do).
I don't have a temperature meter, but will say the effect on the a/c air was noticeable, but not extremely colder. I only covered the portions on the low pressure line (top) that were easily accessible (and straight), and will spend more time later to cover all the little spots...
Thanks for this DIY!
$1.92 at Lowes for 6 feet of self-adhesive 3/4" Inside Diameter tube.
$3.19 at Walmart for 200F duct tape (low quality, but will probably do).
I don't have a temperature meter, but will say the effect on the a/c air was noticeable, but not extremely colder. I only covered the portions on the low pressure line (top) that were easily accessible (and straight), and will spend more time later to cover all the little spots...
Thanks for this DIY!
Also, holding my hand over the tube feeling the radiant heat from the exhaust, I don't see how it can end up burning or melting. Granted its a windy day, but immediately after shutting down from a drive, it wasn't too warm to touch.
Welp, I made the video as planned yesterday, but immediately after doing so, I figured out a much better and less butt-ugly way to wrap the pipe; I redid it after work today without the camera running. So, I'll throw up a video/pic mix instead shortly.
Is this the "butt ugly" one or the other one?Originally Posted by Echostatic ↑
Other.
That video was INTENSE!!!!
*shrug* Now it's gone.
wHy?Originally Posted by Echostatic ↑*shrug* Now it's gone.
I did header wrap on my e-bay stainless header two years ago and cut under hood temps. Pick up stainless steel tie-wraps from Harbor Freight to hold the insulation on your header. My critics predicted I'd burn through the header by now but it hasn't happened (yet).
Texas. That explains it.
best DIY for summer season
I did this mod recently and I can't say I really notice a difference. It might be cooler but if someone did this mod and didn't tell me I doubt I would ever notice.
this will keep me busy for a bit get my mind off other upgrade...cool..i meant that literally...lol
I've now had this mod for a year; a/c blows very cold, and begins blowing cold air almost instantly, much faster than without this mod. I had it on during winter, didn't run the a/c, but had no problems with air box freezing or anything like that. The tube wrapped in the heat resistant duck tape is holding up very well; no melting marks or dis-colorization.
Strong recommend!!
Strong recommend!!
Well, since I'm off to home depot right now anyways I'm going to look at into this mod. If I do it I'll wrap the insulation in aluminum tape...
Just reporting that I've done this and it does make a difference. The A/C feels a lot cooler and gets cool a lot quicker than before.
My g/f doesn't like it though she gets too cold now lol.
My g/f doesn't like it though she gets too cold now lol.
Just finished doing mine tonight actually
Got most of the line. Tried using this stuff and it was horrible
So I ended up using the 97cent foam ones + metal tape.
Got most of the line. Tried using this stuff and it was horrible
So I ended up using the 97cent foam ones + metal tape.

I just wrapped mine. What I thought was a 1 man, 5 minute job tuned into a 2 man, 15 minute job. I used 1/2 in. wrap instead, it fit nicely when it was straight, but at the bends it was a pain. Some of the bends aren't fully wrapped, I couldn't get it all the way around. C'est le vie.
EDIT: And yes, JUST in time for summer!
EDIT: And yes, JUST in time for summer!
Am I the only one who thinks the yaris a/c works very well even down here the florida humidity?