Yarisworld Archive

DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag

293 posts · 385,443 views · page 3 of 6

Replies continued

CTScottThread starterUSA, CT · Jun 2, 2009#101
Originally Posted by bronsin ↑
On my computer when you look at the instructions at the beginning of this post, theres a problem. Instead of a picture of the 4 and 2 switch hookup, there are red X's. Can someone post a drawing of the two ways to wire the switches up? Thanks!
The photos are on photobucket, which gets blocked by many corporate proxy servers. PM me your email address and I'll send you the instructions with the pictures.
Pitt YarisPittsburgh · Jun 2, 2009#102
Originally Posted by PatrickJohnson ↑
some pics of my install. it's all permanent and looking good!
2008....did you have the icon on your gauge cluster? I looked on mine, but didn't have one. Bummer.
PatrickJohnsonMurfreesboro, TN · Jun 3, 2009#103
No, the 2008 LB doesn't have the light on the dash. But really, I didn't need it. I may at some point add the other 2 buttons though.
regalPA · Jun 3, 2009#104
If you have an 09 I would just buy an oem stalk from ebay for $30, you really not sving much be using buttons.
bronsinnj · Jun 3, 2009#105
Looking at the switches, EB1900-ND, I see it takes a half inch hole to mount. Id like to do the four switch version. Im thinking this could crowd the hole behind the panel. And it would be difficult to drill 4 half inch holes in the panel that close together. Im thinking of using a smaller switch which takes a .19 inch mounting hole. The eb1900 is rated 3 amp @ 125VAc. The smaller switch is rated .5A @ 125VAC. Will this be enuf? Thanks!
CTScottThread starterUSA, CT · Jun 3, 2009#106
Originally Posted by bronsin ↑
Looking at the switches, EB1900-ND, I see it takes a half inch hole to mount. Id like to do the four switch version. Im thinking this could crowd the hole behind the panel. And it would be difficult to drill 4 half inch holes in the panel that close together. Im thinking of using a smaller switch which takes a .19 inch mounting hole. The eb1900 is rated 3 amp @ 125VAc. The smaller switch is rated .5A @ 125VAC. Will this be enuf? Thanks!
The current draw in negligible, so any switch will work. Fitting four of the ones I used is tricky. I drew it up in CAD and found that I only had a margin of about 1/8" for the four switches to fit through the hole behind the trim piece. One thing I just realized that I didn't check how much that hole can be widened.
CTScottThread starterUSA, CT · Jun 3, 2009#107
Originally Posted by regal ↑
If you have an 09 I would just buy an oem stalk from ebay for $30, you really not sving much be using buttons.
There's not a huge savings in using the OEM stalk; To me it was more about not having to pull the steering wheel to install it.
bronsinnj · Jun 3, 2009#108
Originally Posted by CTScott ↑
The current draw in negligible, so any switch will work. Fitting four of the ones I used is tricky. I drew it up in CAD and found that I only had a margin of about 1/8" for the four switches to fit through the hole behind the trim piece. One thing I just realized that I didn't check how much that hole can be widened.

The hole can be widened A LOT, maybe half an inch on the radius. The catch is the plastic material is like an inch thick. It would make a huge mess to remove it.

PS the switch Im thinking of using is Digikey EG2021-ND.
CTScottThread starterUSA, CT · Jun 3, 2009#109
Originally Posted by bronsin ↑
The hole can be widened A LOT, maybe half an inch on the radius. The catch is the plastic material is like an inch think. It would make a huge mess to remove it.
That's the nice thing about mounting the switches to that removable trim piece - All of the drilling mess happens on the bench instead of in the car.
bronsinnj · Jun 4, 2009#110
Here is my switch install showing the radio shack numbers. Note: I havnt tried this out in the dash to see if my hole position is correct!


Picture lost · i277.photobucket.com
CTScottThread starterUSA, CT · Jun 4, 2009#111
Originally Posted by bronsin ↑
Here is my switch install showing the radio shack numbers. Note: I havnt tried this out in the dash to see if my hole position is correct!


Picture lost · i277.photobucket.com
Looks close. If you look at the scratched cross and circle on the back of mine you can see the center point of the hole and approximate diameter.

bronsinnj · Jun 4, 2009#112
Looks like its possible with these switches that they will fit even if they dont make the hole, judging by the standoffs on the panel itself.

Yeah it fits! The switches are on a 3/4 inch circle. The center of the circle is 1 3/16 inches from the top of the panel (as measured on the outside of the panel) and 1 7/16 inches from the right side of the panel. I cut a 1 1/2 inch circle (the diameter of the cutout in the dash)from a piece of paper and laid out the switches on the paper. Then glued the paper to the panel measureing the center point of the circle from the sides.
marcustoronto, canada · Jun 4, 2009#113
would this work for any other cars..
CTScottThread starterUSA, CT · Jun 4, 2009#114
Originally Posted by marcus ↑
would this work for any other cars..
Such as?

I would think that based on what we found with the Yaris it would probably be doable for any drive by wire Toyota.
marcustoronto, canada · Jun 4, 2009#115
nice...
bronsinnj · Jun 4, 2009#116
IM thinking something similiar will work for all such DBW cars.
Pitt YarisPittsburgh · Jun 4, 2009#117
Originally Posted by PatrickJohnson ↑
No, the 2008 LB doesn't have the light on the dash. But really, I didn't need it. I may at some point add the other 2 buttons though.
So did you have to do more than ctscott?
CTScottThread starterUSA, CT · Jun 4, 2009#118
Originally Posted by Pitt Yaris ↑
So did you have to do more than ctscott?
Take a look at this thread:

Can we do this? (aka The DIY Cruise Control Thread)

It shows what is required to do it with and 07 or 08. Basically, the extra work is running a wire from the switches to an empty pin on the ECM.
bronsinnj · Jun 5, 2009#119
Mod is in and working! The lights for CC come on in the dash and the four buttons are working. I really needed this because my feet are going numb and its hard to feel how much to press the gas pedal. Now I can do it with the pushbuttons a lot of the time. Thankyou so much for this idea!

PS The wife and everybody at work were not exactly supportive about this. "Whattaya messin' wit a bran new car fo...yo is gonna RUIN it!" You need to break through this negative energy sometimes!

PPS My car is a 2009 Basic 2 door HB. Made last September. Oh and it is black in color. I think that helped....
bronsinnj · Jun 5, 2009#120
I have two sets of resistors and two sets of switches I bought that I didnt use. For $5 Ill send you a set. PM me if intereted.
POORSHANE CT · Jun 5, 2009#121
pm'd
CTScottThread starterUSA, CT · Jun 5, 2009#122
Originally Posted by POORSHA ↑
pm'd
Let me know if you need help with the install, since you're in CT as well.
nickhjortOneida, NY · Jun 5, 2009#123
Hold on just a couple more days and I'll have that module installed. I just haven't had time to rip the dash again. I also have to rethink my clutch switch, the switch broke. That's what I get for going cheap :) Anyway, I'll prolly just buy the oem one. I'll put picks up when I'm done with all of this...
POORSHANE CT · Jun 5, 2009#124
thanks i might just take you up on it
goat1of2USA · Jun 6, 2009#125
In order to provide the on-off indicators which some folks want...rather than messing with wiring LEDS and such, why not just buy an illuminated switch button? Would that work? If so, which Digikey part number would you supersmart electronics types recommend?

I'm about to make an offer on an 07 Yaris without cruise and am MOST grateful that I stumbled on this thread! Thank you all!
CTScottThread starterUSA, CT · Jun 6, 2009#126
Originally Posted by goat1of2 ↑
In order to provide the on-off indicators which some folks want...rather than messing with wiring LEDS and such, why not just buy an illuminated switch button? Would that work? If so, which Digikey part number would you supersmart electronics types recommend?

I'm about to make an offer on an 07 Yaris without cruise and am MOST grateful that I stumbled on this thread! Thank you all!
The illuminated switch won't work without the same type of driving circuitry, due to the switch being a momentary input (rather than a latching switch). Basically, in electronic terms you need a flip-flop, which takes a single input and toggles the output each time the input is pulsed.
CTScottThread starterUSA, CT · Jun 7, 2009#127
Originally Posted by daftcain ↑
I'm probably going to do this mod soon and I'm about to gather what parts I need. I'll probably go with the mounted two button method, and since I have an 07 3-door HB auto, I'll need to run a wire through the firewall. This seems like it will be the same installation as Patrick Johnson (DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag). I'll get the resistors/switches from digikey, where should I get the wiring and what gauges? Also how hard is it to feed a wire through the rubber hose and have it come out the other side?

The wire gauge isn't critical, as there is no current involved (we're just switching a signal input). I would go with between 22 and 18 gauge. You could purchase a small spool at Radio shack or Home Depot.

Feeding through the passenger side rubber boot is fairly easy. Poke a small hole, shove through a semi-rigid piece of wire, and then pull through your wire.
bronsinnj · Jun 11, 2009#128
nickhjortOneida, NY · Jun 22, 2009#129
Awesome install Patrick Johnson and bronsin! Looks just like mine. I'm glad this is working out for everyone :)
bronsinnj · Jun 23, 2009#130
How many have done the install? Many who see mine comment on the coolness. But an equal number say "You did WHAT?!"

PS I still have a set of four switches and the resistors to do this mod. $5 gets it mailed to your door.
BravejusPlattsburgh, NY · Jun 28, 2009#131
I just did this mod also, however i mounted my two button setup in the empty pop out panel next to the dimmer roller switch.
luigiAugusta, GA · Jul 6, 2009#132
Bravejus, i was thinking of mounting in the same place. Got any pics?
trialsdorkparadiso · Jul 6, 2009#133
It worked! I mounted the buttons inside the coin tray as a trial, they're completely hidden. I also installed a mini-deans connector so that I can take the whole mess out in the event of a warranty problem. I think I'll relocate them to the empty removable panel next to the dash light dial soon, for user friendliness. THanks!!!!
solarVitzSan Diego · Jul 12, 2009#134
wow, these really works guys? ive got to try these on my car now. i wonder if my 08 liftback S got the cruise control lights in the instrument cluster? will soon find out.
PatrickJohnsonMurfreesboro, TN · Jul 12, 2009#135
Originally Posted by solarVitz ↑
wow, these really works guys? ive got to try these on my car now. i wonder if my 08 liftback S got the cruise control lights in the instrument cluster? will soon find out.
it doesn't, the 07 and 08 don't have it, only the 09
Blue_dragon_192Florida · Jul 13, 2009#136
Can I assume that this will work for the 09 Sedan also?

What dangers/issues do I need to be worried about doing this mod?
I have wires running all over from the LED mods so I am not worried about the work, just warranty issues.

Blue
bronsinnj · Jul 13, 2009#137
As I understand it yes, the mod works for the 09 Sedan. Its just a matter of tapping into the two wires under the steering wheel and hooking them up to the four (or two if you prefer) switches with the resistors. With an 09 you dont need to be concerned with the ECM.
PatrickJohnsonMurfreesboro, TN · Jul 13, 2009#138
Originally Posted by Blue_dragon_192 ↑
Can I assume that this will work for the 09 Sedan also?

What dangers/issues do I need to be worried about doing this mod?
I have wires running all over from the LED mods so I am not worried about the work, just warranty issues.

Blue
Just an FYI, the burden of proof is on the warranty provider to prove that any modification resulted in a failure of the component or part being warrantied. They can't deny a warrantly claim unless they can prove your modification caused whatever is broken.
Blue_dragon_192Florida · Jul 13, 2009#139
I guess I am screwed on this fantastic inexpensive mod. 🙁

Here are the pics I just took of my steering column.
As you can see, the brown and blue cables are missing.....so I think anyway.

Can someone confirm?
Circled the connector where I think the two additional cables should be:


Picture from the bottom of the steering column...


Blue
CTScottThread starterUSA, CT · Jul 13, 2009#140
Originally Posted by Blue_dragon_192 ↑
I guess I am screwed on this fantastic inexpensive mod. 🙁

Here are the pics I just took of my steering column.
As you can see, the brown and blue cables are missing.....so I think anyway.

Can someone confirm?

That is correct. Looks like the 09 sedan doesn't have the wiring in place from the steering column to the ECM. Does it have the cruise indicators on the combination meter?

You're not totally dead in the water for this mod. You just have to do the 07-08 method, which involves running a single wire from the switches to the ECM. Take a look at the tail end of this thread:

Can we do this? (aka The DIY Cruise Control Thread)
Blue_dragon_192Florida · Jul 13, 2009#141
Originally Posted by CTScott ↑
That is correct. Looks like the 09 sedan doesn't have the wiring in place from the steering column to the ECM. Does it have the cruise indicators on the combination meter?

You're not totally dead in the water for this mod. You just have to do the 07-08 method, which involves running a single wire from the switches to the ECM. Take a look at the tail end of this thread:

Can we do this? (aka The DIY Cruise Control Thread)
Yes it does have the cruise indicators, but they are way at the top of the gauge cluster.

I will look at the 07-08 section. Thanks for the input.
<-goes and mopes and grumbles about not having cruise control. 😁
Blue_dragon_192Florida · Jul 13, 2009#142
ctscott,

one last question (for the next 30 seconds 😁)

With the 07=08 mod, all we are doing to shorting pin 40 on the ECU to ground to turn on the CS and then short it to ground with a load (~600 ohms) to set the CS..

Or did I miss something?

Blue
CTScottThread starterUSA, CT · Jul 13, 2009#143
Originally Posted by Blue_dragon_192 ↑
ctscott,

one last question (for the next 30 seconds 😁)

With the 07=08 mod, all we are doing to shorting pin 40 on the ECU to ground to turn on the CS and then short it to ground with a load (~600 ohms) to set the CS..

Or did I miss something?

Blue
That's all that's to it. See if your sedan has a wire already in pin 40. If so, you can tap it way up under the dash (per the discussion buried in that thread), or at least tap it somewhere along the line.
Blue_dragon_192Florida · Jul 13, 2009#144
Originally Posted by CTScott ↑
That's all that's to it. See if your sedan has a wire already in pin 40. If so, you can tap it way up under the dash (per the discussion buried in that thread), or at least tap it somewhere along the line.
Ok. The next dumb question. Where is the ECM??????
PatrickJohnsonMurfreesboro, TN · Jul 13, 2009#145
if you are standing in front of the car looking at the engine bay, it is attached to the firewall in the upper left corner
CTScottThread starterUSA, CT · Jul 13, 2009#146
And to answer the next question, here's the location of pin 40:

Blue_dragon_192Florida · Jul 13, 2009#147
Originally Posted by CTScott ↑
And to answer the next question, here's the location of pin 40:

OK.

looking at the engine bay and now understand the diagrams....
Since it's too dark out and my wife's scion is in the garage, I will attempt this at a different date.
Thank you all for your input...i hope this works.
RevssonSoutheast Wisconsin · Jul 14, 2009#148
Where's the engine bay?? 😕


just kidding 😁

I have the factory cruise, but if I didn't, I'd probably try this mod.
CT Scott is one of the best with electronics in this forum!!! 👍
Blue_dragon_192Florida · Jul 14, 2009#149
Originally Posted by Revsson ↑
Where's the engine bay?? 😕


just kidding 😁

I have the factory cruise, but if I didn't, I'd probably try this mod.
CT Scott is one of the best with electronics in this forum!!! 👍
Wait................These things have engines? 😲

And here I thought they ran by magic.

Revsson, I am very fluent in sarcasm.......👍

From all the posts I read, CT Scott knows his stuff. I now have to get the courage to mess with the ECM and get the cruise working.
I am far more comfortable in a room full of servers, the car stuff is a little daunting, when dealing with an ECM!
bronsinnj · Jul 20, 2009#150
I had the Yaris out this weekend for a trip to upstate NY and back. (about 250 miles each way) So the CC mod got a good workout. It worked very well indeed! The car got just about 40 mpg when I set the speed on 70 mph. I did the four switch version which gives you plus one and minus one mph at the touch of a button. It came in very handy and I recommend going the four switch route if you install this mod. Getting the Radio Shack really mini switches made doing the four switch really easy...