Yarisworld Archive

DIY - 1.8L 1ZZ-FE TB Connector Chip Swap

322 posts · 207,058 views · page 5 of 7

Replies continued

PHXDEMONPhoenix, AZ · May 11, 2009#201
okay so the idle screw was all the way in and I backed it up as far as I could. Let the car idle for about 10 minutes and slowly the idle smoothed out completely 🙇 While driving I am still getting some jerkyness and moderate oscillation (1-2k) at stop lights but nowhere near as bad as it was. It seems the ECU is actually trying to learn the new throttle body now instead of just being a whore about it. Hopefully it will smoothe itself out some more as I drive it more.
marcustoronto, canada · May 11, 2009#202
hope that fixes ur issue..
PHXDEMONPhoenix, AZ · May 11, 2009#203
Originally Posted by marcus ↑
hope that fixes ur issue..
Oh believe me so do I 😆 Hell I can even live with how it is now it's just that pegging from 1-4k nasty oscillation was horrible. The car was almost undrivable 👎
eiiLong Beach, CA · May 11, 2009#204
Originally Posted by PHXDEMON ↑
Correct others have plugged them I just left them as is. Just go down to a lowes/home depot/etc and get a coupler barb for 3/8 inch ID vinyl tubing and you are food to roll. Stock clamps work and everything just need the barb.
FYI, I'm always food to roll..always.
PHXDEMONPhoenix, AZ · May 11, 2009#205
Originally Posted by eii ↑
FYI, I'm always food to roll..always.
😆😆😆 Did you do the bypass?
PHXDEMONPhoenix, AZ · May 12, 2009#206
Yay my motor is finally running half decent and I got a CEL 👎
AlexNet0Rockland, ME · May 12, 2009#207
Originally Posted by PHXDEMON ↑
Yay my motor is finally running half decent and I got a CEL 👎
that must mean its working! 🤣
marcustoronto, canada · May 12, 2009#208
Originally Posted by PHXDEMON ↑
Yay my motor is finally running half decent and I got a CEL 👎
nice.. so ur saying it idles the same as stock and no oscillations.. what about start up how high does it warm up to..

no wwe jsut need to kill the cel ..
jkuchtaL.A. · May 12, 2009#209
What code is the CEL associated with?

Also, for the people that are still having problems with the swap:

Are you guys using the stock Yaris gasket (the black O-ring with the "tail" and the partial mesh screen) with the 1ZZ TB?

If not...you should use at least the "tail" portion. The slot that the "tail" fits in on the intake manifold offers a totally open channel through which air will get in and cause idle speed "hunting" and CEL's. The channel is large enough to suck in any partially set gasket maker and give you problems such as rough idle and CEL's.

When I did the install I cut off the "tail" from the gasket and installed it in the channel in the intake manifold with gasket maker. Once set, the "tail" creates a nice solid plug for that channel, and I haven't had a single CEL since I made the chip swap....not ONE!
marcustoronto, canada · May 13, 2009#210
wow no oscillation and no cel ...
RagnaCaTVillalba, Puerto Rico · May 13, 2009#211
After 12 pages I feel I should do this....
jkuchtaL.A. · May 14, 2009#212
Originally Posted by marcus ↑
wow no oscillation and no cel ...
Yep...read post #78 in this thread!
PHXDEMONPhoenix, AZ · May 16, 2009#213
Well the CEL finally disappeared and it ran great for about a mile. and then this 😢



Fuck this throttle body. Put the stocker back on and it is running great.
eiiLong Beach, CA · May 16, 2009#214
Whaaaaaaaaaaaaaaaaaaat? Please explain what happened. I'm scared, I'm scared for my life now.
jkuchtaL.A. · May 16, 2009#215
So what went wrong? Do you know what the CEL code was?

Please tell me step-by-step how you installed the 1zz TB so we can figure out what went wrong. I've been running mine without fault for a few months now...there's got to be something simple that can be fixed and will clear up the whole problem.

And eii, if you want to go for a ride in a yaris with the 1zz tb install that was done correctly, PM me.
PHXDEMONPhoenix, AZ · May 18, 2009#216
Originally Posted by jkuchta ↑
So what went wrong? Do you know what the CEL code was?

Please tell me step-by-step how you installed the 1zz TB so we can figure out what went wrong. I've been running mine without fault for a few months now...there's got to be something simple that can be fixed and will clear up the whole problem.

And eii, if you want to go for a ride in a yaris with the 1zz tb install that was done correctly, PM me.
CEL was gone. Car completely died and wouldn't even idle. Start it up and it woul ddie instantly. I used the original gasket plus gasket maker, I did the coolant bypass, I did the chip swap. I did everything it just didn't work out for me 🙁
Yaris T-Sport.. · May 18, 2009#217
Originally Posted by PHXDEMON ↑
CEL was gone. Car completely died and wouldn't even idle. Start it up and it woul ddie instantly. I used the original gasket plus gasket maker, I did the coolant bypass, I did the chip swap. I did everything it just didn't work out for me 🙁
That could be pretty much the 1ZZ T/B itself being the problem, try another different 1ZZ T/B or try the 2AZ-FE 2.4L T/B.

remember! failing is the beginning of success, it wasn't easy for me either
jkuchtaL.A. · May 18, 2009#218
Bummer...

Do you know what the code for the CEL you were getting was? It may provide some clues as to what caused your problem.
bienimanSuriname South America · May 20, 2009#219
Guys,
I've been following this mod for a while now,

If I'm correct the newer yaris models have electronically controlled TB. Well, I looked under my hood and see sort of like a cable running from the pedal to the TB, I can rev my engine by turning this swivel.

bienimanSuriname South America · May 20, 2009#220
O yeah forgot to ask.

Can I do this mod also to my , Vitz Rs 2001?????
enviriCT · May 20, 2009#221
dude! i was about to put it on! now im gonna have second thoughts or get garm's! jeez...i think there HAS to be something we're missing...a hidden variable thats affecting some of us...

Originally Posted by PHXDEMON ↑
Well the CEL finally disappeared and it ran great for about a mile. and then this 😢

Fuck this throttle body. Put the stocker back on and it is running great.
AlexNet0Rockland, ME · May 20, 2009#222
Originally Posted by bieniman ↑
Guys,
I've been following this mod for a while now,

If I'm correct the newer yaris models have electronically controlled TB. Well, I looked under my hood and see sort of like a cable running from the pedal to the TB, I can rev my engine by turning this swivel.

Yes, this mod only applies to the Drive by wire system that is in the ( i believe) '05 and newer
AlexNet0Rockland, ME · May 20, 2009#223
Originally Posted by PHXDEMON ↑
CEL was gone. Car completely died and wouldn't even idle. Start it up and it woul ddie instantly. I used the original gasket plus gasket maker, I did the coolant bypass, I did the chip swap. I did everything it just didn't work out for me 🙁
doesnt sound like the TB unless a wire snapped somewhere.
PHXDEMONPhoenix, AZ · May 20, 2009#224
Originally Posted by AlexNet0 ↑
doesnt sound like the TB unless a wire snapped somewhere.
Stocker works flawless though so it isn't a wiring issue.
PHXDEMONPhoenix, AZ · May 20, 2009#225
Originally Posted by bieniman ↑
Guys,
I've been following this mod for a while now,

If I'm correct the newer yaris models have electronically controlled TB. Well, I looked under my hood and see sort of like a cable running from the pedal to the TB, I can rev my engine by turning this swivel.

I'm not 100% positive on this but the scion xa/xb owners have done a swap with an older 1zz throttle body which is drive by cable like yours. check the forums @ scionlife.com you should be able to dig up more info.
MGarganoNJ · May 21, 2009#226
The chip swap was working fine for me... no CEL or oscillation... until I had to disconnect the battery to swap the steering wheel. Once I reconnected, oscillation & CELs galore.
jkuchtaL.A. · May 21, 2009#227
What codes are showing up?

Just saying you have a CEL is kind of worthless unless we know what the code is. It could be just a case of needing to adjust the idle set screw, or a number of other things.
MGarganoNJ · May 21, 2009#228
Originally Posted by jkuchta ↑
What codes are showing up?

Just saying you have a CEL is kind of worthless unless we know what the code is. It could be just a case of needing to adjust the idle set screw, or a number of other things.
P0505- Idle Malfunction
jkuchtaL.A. · May 21, 2009#229
Have you adjusted the idle screw? If you've turned the screw out too far you could get this code...try turning the screw in one or two turns (with the car off). This should fix the problem.

If you haven't adjusted the idle set screw, turn it counter-clockwise 1.5 turns (with the engine off), and see what happens.
MGarganoNJ · May 21, 2009#230
Originally Posted by jkuchta ↑
Have you adjusted the idle screw? If you've turned the screw out too far you could get this code...try turning the screw in one or two turns (with the car off). This should fix the problem.

If you haven't adjusted the idle set screw, turn it counter-clockwise 1.5 turns (with the engine off), and see what happens.
I haven't touched the idle screw at all. The thing was working perfectly for over a month, right up until I disconnected the battery. I'm not going through this every time I disconnect the battery... plus, even when it's working perfectly, the high idle is now quite loud with the exhaust I have. I'm 99% I'm switching back to the stocker today.
YodaFL · May 21, 2009#231
any one has a DYI on how to install the TB? I am looking through tha manuall and drawing a blank. Do i need anything special?
jkuchtaL.A. · May 21, 2009#232
Originally Posted by MGargano ↑
I haven't touched the idle screw at all. The thing was working perfectly for over a month, right up until I disconnected the battery. I'm not going through this every time I disconnect the battery... plus, even when it's working perfectly, the high idle is now quite loud with the exhaust I have. I'm 99% I'm switching back to the stocker today.
If you turn the idle set screw out about a turn and a half, all of your problems will go away.

When you leave the screw is the "corolla" position, the yaris ECU adjusts the idle fuel to get a stable idle. This takes time, as the ECU needs to make some pretty big changes. When you adjust the idle set screw to the correct position, the ECU doesn't have to work nearly as hard to get a normal idle, so the ECU doesn't freak out.

The idle rpm fluctuations are a result of the ECU hunting for the right fueling to maintain a steady 600-700 rpm idle in the face of way too much air going through an unadjusted corolla TB.

The P0505 code is the ECU saying..."WTF!!...Why can't I idle at the fuel trims I'm programmed with...something must be wrong!!"
AlexNet0Rockland, ME · May 21, 2009#233
Originally Posted by Yoda ↑
any one has a DYI on how to install the TB? I am looking through tha manuall and drawing a blank. Do i need anything special?
If you search, you will find it. there have been like 3
YodaFL · May 21, 2009#234
Originally Posted by AlexNet0 ↑
If you search, you will find it. there have been like 3
thx it wasnt too hard so i didnt need the diy. Didnt do the chip swap gonna see what other means there are to eliminate the cel if i get any.🙄
jkuchtaL.A. · May 21, 2009#235
Originally Posted by Yoda ↑
thx it wasnt too hard so i didnt need the diy. Didnt do the chip swap gonna see what other means there are to eliminate the cel if i get any.🙄
If you adjust the idle set screw you might be ok.
AlexNet0Rockland, ME · May 21, 2009#236
Originally Posted by Yoda ↑
thx it wasnt too hard so i didnt need the diy. Didnt do the chip swap gonna see what other means there are to eliminate the cel if i get any.🙄
Did you get the oscillation? thats what the chip swap was originally indended to fix
YodaFL · May 21, 2009#237
Originally Posted by jkuchta ↑
If you adjust the idle set screw you might be ok.
adjust it to were? sry total noob at this. dont even kno where the darn thing is🤷
marcustoronto, canada · May 21, 2009#238
Originally Posted by Yoda ↑
adjust it to were? sry total noob at this. dont even kno where the darn thing is🤷
ok sorry its this one like he said.
P1010183.jpg
YodaFL · May 21, 2009#239
Originally Posted by marcus ↑
there
clockwise? anticlockwise? how much of a turn?
o and is it an actual screw cause there is none...
tk-421Dagobah · May 21, 2009#240
Originally Posted by marcus ↑
there
That's not the idle screw. It's this one (covered in epoxy here):


You'll need a small allen wrench to turn it BTW. As far as CW/CCW, I can't remember... I believe I ended up turning it CW almost all the way.
YodaFL · May 21, 2009#241
Originally Posted by tk-421 ↑
That's not the idle screw. It's this one (covered in epoxy here):


You'll need a small allen wrench to turn it BTW. As far as CW/CCW, I can't remember... I believe I ended up turning it CW almost all the way.
ok kwel i will try it as is now then adjust later the rain lifted up sp let me finish installing it. It was hard as heck to get the afe coupler over the TB had to shave some off.🙁
YodaFL · May 21, 2009#242
so yea i installed it right. i was doing the whole coolant overflow thing and well it didnt. I waited for like 5 min and no overflow so i was like ok. No oscillation just high cold and when its warm it setlles at a high of 1100rpm and a CEL🤷 Againg i said ok. Before i went to disconnect the battery i tried stepping on the throttle. This event was followed bu very very very slow climb in rpm. Again ok... So i floored it🙄 Not a good idea didnt make a diff at all the car started shaking and i quickly turned it off. So yea the battery is disconnected and i will wait a ahwile before i see wat is up. Any ideas lol?
tk-421Dagobah · May 21, 2009#243
The cold start sounds normal to me. In my case it's always @ 2.5K
It shouldn't settle @1.1K though... That sounds high to me when idling.
The CEL thing is hit/miss... Some ppl get it, some ppl don't. 🤷
YodaFL · May 21, 2009#244
Originally Posted by tk-421 ↑
The cold start sounds normal to me. In my case it's always @ 2.5K
It shouldn't settle @1.1K though... That sounds high to me when idling.
The CEL thing is hit/miss... Some ppl get it, some ppl don't. 🤷
yea but something is up with the throttle. i gonna try it again once it resets. I think i might have to turn the screw until the idle get down to normal. Little small turns lol.
I hope i didnt get a defective one.😠
jkuchtaL.A. · May 22, 2009#245
Turn the idle screw 1.5 turns counter-clockwise. Also, if you used any gasket maker, you need to not run the car for a few hours to let that stuff cure, or else the idle vacuum will suck the stuff into the intake manifold...which will give you really erratic running and a CEL.
YodaFL · May 22, 2009#246
well its morning gonna try again that idle screw is hard to turn.
YodaFL · May 22, 2009#247
ffs its stripped the fing screw!!!
marcustoronto, canada · May 22, 2009#248
get rid of the glue.. then try wd40.
jkuchtaL.A. · May 22, 2009#249
If the set screw is toast get a broken bolt remover and pull it out. I believe an M3x20mm screw will work as a replacement.
YodaFL · May 22, 2009#250
ok so i got back throttle response due to chip swap but its idling at 1.6k warm.....
Also when i tried the holding rpm thing it just starts to bounce up and down :(. I think i may need to disconnect the battery longer cause i only did it for 20 min. got to find a way to get that screw out.

O btw i just realized that the TB i got came from an auto trans car. Do you think that makes a diff?