nah, i know i can just swap TBs a week before emissions and it will be fine.
DIY - 1.8L 1ZZ-FE TB Connector Chip Swap
322 posts · 207,058 views · page 2 of 7
Replies continued
for those who have the Idling Control CEL (P0505), a question:
Have you tried to reset the ECU? (by disconnecting the battery for a little while or removing the appropriate fuse). I am looking through the repair manuals about this specific trouble code, it happens when the idle speed does not match to the learned air intake volume. i.e. this bigger throttle is letting in more air at idle, more than the ECU remembers from the original throttle, thus it throws a code.
So, letting the car idle for a long time when it is warmed up is one way to "re-learn" the idle airflow, or resetting the ECU is potentially risky but should be faster.
On the other hand, the high warmup idle, I'm not sure anything can be done about that, but in itself it should not be throwing any malfunction codes.
For reference:
Have you tried to reset the ECU? (by disconnecting the battery for a little while or removing the appropriate fuse). I am looking through the repair manuals about this specific trouble code, it happens when the idle speed does not match to the learned air intake volume. i.e. this bigger throttle is letting in more air at idle, more than the ECU remembers from the original throttle, thus it throws a code.
So, letting the car idle for a long time when it is warmed up is one way to "re-learn" the idle airflow, or resetting the ECU is potentially risky but should be faster.
On the other hand, the high warmup idle, I'm not sure anything can be done about that, but in itself it should not be throwing any malfunction codes.
For reference:
DESCRIPTIONJust a theory, really, but worth trying!
The idling speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of:
1) the one valve type throttle body;
2) the throttle actuator, which operates the throttle valve;
3) the Throttle Position (TP) sensor, which detects the opening angle of the throttle valve;
4) the Accelerator Pedal Position (APP) sensor, which detects the accelerator pedal position; and
5) the ECM, which controls the ETCS. Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.
MONITOR DESCRIPTION
The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following conditions apply:
• The learned idling air flow volume remains at the maximum or minimum volume 5 times or more during a drive cycle.
• After driving at 6.25 mph (10 km/h) or more, the actual engine idling speed varies from the target idling speed by between 100 rpm and 200 rpm, 5 times or more during a drive cycle.
Example:
If the actual idling speed varies from the target idling speed by more than 200 rpm* 5 times during a drive cycle, the ECM illuminates the MIL and sets the DTC.
HINT:
*: Threshold idling speed varies with engine load.
I bet whoever is getting CELs are running the same CAI system. The upgraded TB probably disrupted the balance of being more free-flowing and not throwing CEL for specific CAI systems.
What kind of CAI are you guys running?
What kind of CAI are you guys running?
Ive let me car idle for a very long time and i have also reset the ecu by doing the battery thing as well.
i am running a trd intake
i am running a trd intake
AEM CAI.
Can T-Sport chime in and confirm he still has no CELs after the swap?
yes, I don't have any cel at this point since the swap, I'm thinking maybe the different intake tube/pipe? I'm using the OEM one.
That could be it. I've got a CEL and I have a Cold Air Intake.
does anyone that uses a CAI have the stock one to toss back on to try it out? T-Sport is the bottom of your stock intake gutted? or is it completely stock?
Can anyone dyno their car to prove what this TB swap really does.
So far no asnwer to this question, and it just seems like everyone is jumping on something that just makes the engine rev qierdly and pull "harder" but ok.
So far no asnwer to this question, and it just seems like everyone is jumping on something that just makes the engine rev qierdly and pull "harder" but ok.
well i mean its an easy concept, larger mm throttle body = more air. to get the most out of it you either need a tune or be FI.
well i have put almost 100 miles on it since my last post, the light has been gone the whole time. maybe it had to relearn after the chip swap...idk, but its gone. if it does not come on during my drive to work today then the problem is solved.
And how much faster is your car now honestly? I would really like to know.Originally Posted by mikenacarato ↑well i have put almost 100 miles on it since my last post, the light has been gone the whole time. maybe it had to relearn after the chip swap...idk, but its gone. if it does not come on during my drive to work today then the problem is solved.
I do know the larger TB makes a big difference on some cars, and this is why Im making it such a big deal to learn what a difference this makes to the Yaris.
Thanks.
I'm running with Blitz SUS POWER Air Intake with the OEM intake tubeOriginally Posted by Nexus1155 ↑does anyone that uses a CAI have the stock one to toss back on to try it out? T-Sport is the bottom of your stock intake gutted? or is it completely stock?
would the TRD CAI fit over the TB opening or would i have to "Lip" it?
How much bigger is the new throttle body opening than the intake it bolts to, as the intake side may become the restrictor? From the picture it looks like it has a step so you can't really port match it to the new throttle body.
I'm very sure you can, the other memeber has an TRD intake and he has been running with the new tb.Originally Posted by Jerkratt ↑would the TRD CAI fit over the TB opening or would i have to "Lip" it?
the pic of the my OEM tube has already been ported .25" biggerOriginally Posted by dallas ↑How much bigger is the new throttle body opening than the intake it bolts to, as the intake side may become the restrictor? From the picture it looks like it has a step so you can't really port match it to the new throttle body.
1nz = 2"
1zz = 2.25"
just a report back it's been 11 days since ,my chip swap, cold start idle is around 2000 RPM instead of 3000 before, drops down to around 1000 in a couple of mins, when the car is fully warmed up, it idles at 750 RPM, no CEL the whole time, very happy with the extra mid-nigh end gain, can definitely feel the difference by my butt dyno even off the line, much better mod than an intake or exhaust if you can find one cheap, perhaps I couldn't even feel a difference when I upgraded my intake nor exhaust alone by my but dyno expect the increase of engine noise, but this one, I surely CAN.
Originally Posted by dallas ↑How much bigger is the new throttle body opening than the intake it bolts to, as the intake side may become the restrictor? From the picture it looks like it has a step so you can't really port match it to the new throttle body.
I am thinking the same thing. 🤷
you need a flared silicone rubber adapterOriginally Posted by Jerkratt ↑would the TRD CAI fit over the TB opening or would i have to "Lip" it?
Doing this today, wish me luck😁 Hopefully i won't get any CEL.
I have the AFE intake. Mine just went right over the TB, of course it took a lil muscle but it's on there, snug fit didn't even have to tight the clamp too much.
Originally Posted by Jerkratt ↑would the TRD CAI fit over the TB opening or would i have to "Lip" it?
I was not able to do this at all with the OEM hose + Simota SRI. Did you get the hose wet in order to make it more flexible?Originally Posted by hatchbackkid82 ↑I have the AFE intake. Mine just went right over the TB, of course it took a lil muscle but it's on there, snug fit didn't even have to tight the clamp too much.
I'm thinking of buying one of these... for those of you that have installed one, in your opinion is this a good worth while mod?
TIA
TIA
The TB was $60 off of fleabay for me, and I think it was money decently spent.
I have not done the chip swap on mine, and I also just rerouted the cooling hoses to connect together and not through the TB. (Reason being I had it on before checking the angles the hose inlets and outlets and didn't feel like removing the TB and move them into the right area to connect.)
My favorite part to be honest is the higher idle. Previously my car would sit at 640ish (or so sayeth my Defi HUD) and now it's more like 900, which is a bit higher than I would like, but it makes the car more forgiving when leaving a stop.
I DO have the CEL if you're wondering, it appeared and then disappeared after 50 miles after installation and then reappeared like 200 miles ago, so whatever. Oscillation occurs at start up occasionally, but goes away in a minute along with the high idle. (~2300 is what it sits at when the cool light is on)
Butt dyno says no major increase in acceleration or power at lower RPMs, but near redline in 2nd and at WOT in 3rd the change in power is noticeable.
I can't imagine it doesn't give you an increase in power as it's been stated by other members that the ECU only allows the TB to open 80% at WOT. So with this larger TB you'd see an increase at least at WOT I would think.
Also here's a comparison of the stock TB and the 1ZZ TB I took before installation:

I have not done the chip swap on mine, and I also just rerouted the cooling hoses to connect together and not through the TB. (Reason being I had it on before checking the angles the hose inlets and outlets and didn't feel like removing the TB and move them into the right area to connect.)
My favorite part to be honest is the higher idle. Previously my car would sit at 640ish (or so sayeth my Defi HUD) and now it's more like 900, which is a bit higher than I would like, but it makes the car more forgiving when leaving a stop.
I DO have the CEL if you're wondering, it appeared and then disappeared after 50 miles after installation and then reappeared like 200 miles ago, so whatever. Oscillation occurs at start up occasionally, but goes away in a minute along with the high idle. (~2300 is what it sits at when the cool light is on)
Butt dyno says no major increase in acceleration or power at lower RPMs, but near redline in 2nd and at WOT in 3rd the change in power is noticeable.
I can't imagine it doesn't give you an increase in power as it's been stated by other members that the ECU only allows the TB to open 80% at WOT. So with this larger TB you'd see an increase at least at WOT I would think.
Also here's a comparison of the stock TB and the 1ZZ TB I took before installation:

Thanks Gideon! I think I'll be getting one and trying this out.
I strongly recommend this Saggio. I really have felt a difference with this mod. I have taken the TB back off and installed the original (trying to fix the CEL) and couldn't stand the power loss so I re-installed the 1.8L TB. CEL comes and goes, but who cares.
I had planned on picking one of those tb up this weekend from the same ebay guy , and your statement just made me 100% on getting one 👍Originally Posted by yarstar ↑I strongly recommend this Saggio. I really have felt a difference with this mod. I have taken the TB back off and installed the original (trying to fix the CEL) and couldn't stand the power loss so I re-installed the 1.8L TB. CEL comes and goes, but who cares.
Just like Gideon, I even like the high rev cold idle. My car sounds like it has a turbine engine when it fires up. The idle goes down once the cold light goes off. High idle only for about a minute.
Before the yaris , I owned nothing but beastly dsm's and mk3 turbos so i'm use to loud cars with rough idle . Imo the yaris was wayyyyy to quite when I first got it . I'm sporting aem w/fujita filter , megan header, nitto mid, hks axle back , nst 10% ud pulley running on 91 and i'm very surprised at how "peppy" this little 1.5 yaris has become . Modds planned are the Tb swap , coolent bypass , tb spacer (for S's and G's and I'm gonna do before and after dyno test for proof good/bad) and my friend is starting on a 1-off long tube header for me(similar to Richard's design)Originally Posted by yarstar ↑Just like Gideon, I even like the high rev cold idle. My car sounds like it has a turbine engine when it fires up. The idle goes down once the cold light goes off. High idle only for about a minute.
Hey everyone:
I did this swap this last Sunday...and man what a differeance!
First off I installed the 1ZZ TB stock (no idle screw adjustment or chip swap). Cold idle was high (around 3K) and fluctuated, like everyone has mentioned, though my warm idle was around 850-900rpm, with a pretty bitchin' roughness (think bigger cam). There were definate problems though.
1) CEL: came on intermittantly with P0171 (iirc) lean condition, especially while transitioning from idle to part throttle, though once cleared, this CEL would not come back while driving or coming back to a stop, which makes me want to rule out any sort of air leak.
2) Throttle response was lacking, and pretty disconnected..i.e. while shifting the engine would over-rev 500-1000rpm, and the car seemed to lack any real grunt anywhere in the powerband. I have a scangauge, and could see I was getting full throttle operation.
3) When the car went into DFCO it would feel like I had just released the 'chuts! With the OEM TB DFCO is almost inperceptable, but with the unadjusted 1ZZ TB it was pretty uncomfortable feeling.
4) Heel-toe downshifting was pretty much impossible as well due to lack of fine rev control, and a wierd over-rev/under-rev (the car stalled itself twice) on deceleration.
These symptoms were consistant over more than 3 hours of driving.
On Monday afternoon, I removed the 1ZZ TB and swapped out the chip with the OEM 1NZ chip. I did this without disconnecting the battery, as I wanted to see how big a difference this swap would make, all other things being equal.
BIG DIFFERENCE!
1) High Cold idle lasts about half as long. Also, there is no ocillation. The rpms just go straight to 2500-2700, and then slowly taper back down.
2) The idle is also much more stable (like stock), with no (albeit cool) roughness.
Now I got to work setting the correct idle speed. For some reason, the epoxy over the idle set screw on my 1ZZ TB came off nice and easy, an in one piece. After a few minutes idleing, the engine settled to about 1K rpm, which set off a CEL (I think P0220 iirc(TB stuck open)). I adjusted the screw to the point of killing the engine (which triggered another CEL (P0505...bad idle)). I then screwed the idle set screw back in about half way, which when the engine was turned back on, gave me an idle of about 850 rpm. I then shut the engine back off and adjusted the screw back out about a turn, which (when the engine was turned back on) gave me a nice stable (and smooth) 720-750rpm.
Based on the manual, this is as high as you can go without running the risk of getting a "bad idle" CEL. This idle rpm also makes leaving stoplights a little better in that the engine doesn't bog quite as much.
A note on setting the idle:
Adjustments should be made with the engine and ignition off, as doing the adjustment with the engine running will only cause the ECU to compensate to maintain the idle speed, almost regardless of the idle set screw position (took me 10 min. to figure that out).
Driving impressions:
1) Throttle response is better than stock, and the car pulls like a motha' (well....way more than with the stock TB🙂) above 2200 rpms.
2) Heel-toe downshifting is better than stock (rpms come up a little faster, and with a little more "control" (i.e. a little tap gives a few hundred rpm (great for the 5th-4th shift), and a bigger dab gives about 1000 rpm (great for 4th-3rd, and 3rd-2nd shifts).
Once the idle was set there have been no CELs of any kind, and the car is a riot to drive!
As far as I'm concerned...this is a must-do mod for anyone with the stomach to do the chip swap (drilling out that first rivet is mentally the hard part😉), though the idle adjustment is pretty much a requirment to make this thing feel right.
A big THANK YOU to T-sport for the diy (and having the nuts to do this in the first place)!🙇
Side note:
I also did the TB coolent bypass. My other mods are as follows : Simota Carbon SRI (the big box), WR header, Thermal axle-back, and nology hotwires, running Shell V-Power and Motul 300V 5W-30.
I did this swap this last Sunday...and man what a differeance!
First off I installed the 1ZZ TB stock (no idle screw adjustment or chip swap). Cold idle was high (around 3K) and fluctuated, like everyone has mentioned, though my warm idle was around 850-900rpm, with a pretty bitchin' roughness (think bigger cam). There were definate problems though.
1) CEL: came on intermittantly with P0171 (iirc) lean condition, especially while transitioning from idle to part throttle, though once cleared, this CEL would not come back while driving or coming back to a stop, which makes me want to rule out any sort of air leak.
2) Throttle response was lacking, and pretty disconnected..i.e. while shifting the engine would over-rev 500-1000rpm, and the car seemed to lack any real grunt anywhere in the powerband. I have a scangauge, and could see I was getting full throttle operation.
3) When the car went into DFCO it would feel like I had just released the 'chuts! With the OEM TB DFCO is almost inperceptable, but with the unadjusted 1ZZ TB it was pretty uncomfortable feeling.
4) Heel-toe downshifting was pretty much impossible as well due to lack of fine rev control, and a wierd over-rev/under-rev (the car stalled itself twice) on deceleration.
These symptoms were consistant over more than 3 hours of driving.
On Monday afternoon, I removed the 1ZZ TB and swapped out the chip with the OEM 1NZ chip. I did this without disconnecting the battery, as I wanted to see how big a difference this swap would make, all other things being equal.
BIG DIFFERENCE!
1) High Cold idle lasts about half as long. Also, there is no ocillation. The rpms just go straight to 2500-2700, and then slowly taper back down.
2) The idle is also much more stable (like stock), with no (albeit cool) roughness.
Now I got to work setting the correct idle speed. For some reason, the epoxy over the idle set screw on my 1ZZ TB came off nice and easy, an in one piece. After a few minutes idleing, the engine settled to about 1K rpm, which set off a CEL (I think P0220 iirc(TB stuck open)). I adjusted the screw to the point of killing the engine (which triggered another CEL (P0505...bad idle)). I then screwed the idle set screw back in about half way, which when the engine was turned back on, gave me an idle of about 850 rpm. I then shut the engine back off and adjusted the screw back out about a turn, which (when the engine was turned back on) gave me a nice stable (and smooth) 720-750rpm.
Based on the manual, this is as high as you can go without running the risk of getting a "bad idle" CEL. This idle rpm also makes leaving stoplights a little better in that the engine doesn't bog quite as much.
A note on setting the idle:
Adjustments should be made with the engine and ignition off, as doing the adjustment with the engine running will only cause the ECU to compensate to maintain the idle speed, almost regardless of the idle set screw position (took me 10 min. to figure that out).
Driving impressions:
1) Throttle response is better than stock, and the car pulls like a motha' (well....way more than with the stock TB🙂) above 2200 rpms.
2) Heel-toe downshifting is better than stock (rpms come up a little faster, and with a little more "control" (i.e. a little tap gives a few hundred rpm (great for the 5th-4th shift), and a bigger dab gives about 1000 rpm (great for 4th-3rd, and 3rd-2nd shifts).
Once the idle was set there have been no CELs of any kind, and the car is a riot to drive!
As far as I'm concerned...this is a must-do mod for anyone with the stomach to do the chip swap (drilling out that first rivet is mentally the hard part😉), though the idle adjustment is pretty much a requirment to make this thing feel right.
A big THANK YOU to T-sport for the diy (and having the nuts to do this in the first place)!🙇
Side note:
I also did the TB coolent bypass. My other mods are as follows : Simota Carbon SRI (the big box), WR header, Thermal axle-back, and nology hotwires, running Shell V-Power and Motul 300V 5W-30.
Originally Posted by jkuchta ↑Hey everyone:
I did this swap this last Sunday...and man what a differeance!
First off I installed the 1ZZ TB stock (no idle screw adjustment or chip swap). Cold idle was high (around 3K) and fluctuated, like everyone has mentioned, though my warm idle was around 850-900rpm, with a pretty bitchin' roughness (think bigger cam). There were definate problems though.
1) CEL: came on intermittantly with P0171 (iirc) lean condition, especially while transitioning from idle to part throttle, though once cleared, this CEL would not come back while driving or coming back to a stop, which makes me want to rule out any sort of air leak.
2) Throttle response was lacking, and pretty disconnected..i.e. while shifting the engine would over-rev 500-1000rpm, and the car seemed to lack any real grunt anywhere in the powerband. I have a scangauge, and could see I was getting full throttle operation.
3) When the car went into DFCO it would feel like I had just released the 'chuts! With the OEM TB DFCO is almost inperceptable, but with the unadjusted 1ZZ TB it was pretty uncomfortable feeling.
4) Heel-toe downshifting was pretty much impossible as well due to lack of fine rev control, and a wierd over-rev/under-rev (the car stalled itself twice) on deceleration.
These symptoms were consistant over more than 3 hours of driving.
On Monday afternoon, I removed the 1ZZ TB and swapped out the chip with the OEM 1NZ chip. I did this without disconnecting the battery, as I wanted to see how big a difference this swap would make, all other things being equal.
BIG DIFFERENCE!
1) High Cold idle lasts about half as long. Also, there is no ocillation. The rpms just go straight to 2500-2700, and then slowly taper back down.
2) The idle is also much more stable (like stock), with no (albeit cool) roughness.
Now I got to work setting the correct idle speed. For some reason, the epoxy over the idle set screw on my 1ZZ TB came off nice and easy, an in one piece. After a few minutes idleing, the engine settled to about 1K rpm, which set off a CEL (I think P0220 iirc(TB stuck open)). I adjusted the screw to the point of killing the engine (which triggered another CEL (P0505...bad idle)). I then screwed the idle set screw back in about half way, which when the engine was turned back on, gave me an idle of about 850 rpm. I then shut the engine back off and adjusted the screw back out about a turn, which (when the engine was turned back on) gave me a nice stable (and smooth) 720-750rpm.
Based on the manual, this is as high as you can go without running the risk of getting a "bad idle" CEL. This idle rpm also makes leaving stoplights a little better in that the engine doesn't bog quite as much.
A note on setting the idle:
Adjustments should be made with the engine and ignition off, as doing the adjustment with the engine running will only cause the ECU to compensate to maintain the idle speed, almost regardless of the idle set screw position (took me 10 min. to figure that out).
Driving impressions:
1) Throttle response is better than stock, and the car pulls like a motha' (well....way more than with the stock TB🙂) above 2200 rpms.
2) Heel-toe downshifting is better than stock (rpms come up a little faster, and with a little more "control" (i.e. a little tap gives a few hundred rpm (great for the 5th-4th shift), and a bigger dab gives about 1000 rpm (great for 4th-3rd, and 3rd-2nd shifts).
Once the idle was set there have been no CELs of any kind, and the car is a riot to drive!
As far as I'm concerned...this is a must-do mod for anyone with the stomach to do the chip swap (drilling out that first rivet is mentally the hard part😉), though the idle adjustment is pretty much a requirment to make this thing feel right.
A big THANK YOU to T-sport for the diy (and having the nuts to do this in the first place)!🙇
Side note:
I also did the TB coolent bypass. My other mods are as follows : Simota Carbon SRI (the big box), WR header, Thermal axle-back, and nology hotwires, running Shell V-Power and Motul 300V 5W-30.
^^^ Very good write up , now i'm really ready to do this modd ! What did you need for the Tb coolent bypass? Just checking so I can buy the right parts the first time .
Double barb 3/4" union (Home depot). I reused the OEM hose clamps (they are in pretty much A1 shape).
Kustom, I got the TB from TheBarber, but eBay is also a good source.
Kustom, I got the TB from TheBarber, but eBay is also a good source.
jkuchta that was a sick review, how many miles have you put on the TB since the chip swap? If its not many i might want to wait a bit to grab one. But it seems like its spot on!
Thanks man👍 I bought mk3 supra parts from the ebay seller in the link in post #19 and he was legit , I plan on getting the tb from him too .Originally Posted by jkuchta ↑Double barb 3/4" union (Home depot). I reused the OEM hose clamps (they are in pretty much A1 shape).
Kustom, I got the TB from TheBarber, but eBay is also a good source.
Great write up Bravo, if you live in a cold climate don't do the coolant bypass, in the winter it will ice, great mod for summer as it reduces intake temps.
Ok so looks like i'm part of the CEL club. Installed it w/o a hitch except for the brass fittinh i had to buy, didn't want to bypass the coolant line through th TB. Started the car up, and had the high idle for about a min. or so. Oscillated for a few seconds before it finally started to taper off and idle normal, slightly higher idle than stock. Drove the car around, has great midrange and top end. After driving it for about 2-3mins i got a CEL👎. Disconnected the battery for a few mins CEL was off again after a few miles came right back on. I've swapped the chip over from the 1NZ TB. I hate CEL👎 Good mod for the money just hate seeing that CEL light on. Also the car does feel like when shifting it's holding on to the revs, instead of the rpm's dropping it feels like it revs at whatever rpm you were at before you shifted. And when coasting in gear maybe it's just me but it seems real jerky at time. It will hit a certain rpm where it does that
No water or anything. Just used my guns😁. But really yhtough the coupler on the AFE intake is flexible a lot more than the oem tube
Originally Posted by tk-421 ↑I was not able to do this at all with the OEM hose + Simota SRI. Did you get the hose wet in order to make it more flexible?
Anyone know how to get that expoxy off to adjust the idle control?
i dont think anything makes epoxy soluble, the only way to do it is either burn it off, or pick it out
Freeze Spray or pick it out.
Picture lost · www.psl-equip.com
Picture lost · www.psl-equip.com
The only experiance I have is with the Corolla TB, so that's the only one that I can say for sure fits.
Dallas,
The TB can't ice up, as there is no fuel passing through the TB. To get normal intake air to ice up you'd need to run it through a really small venturi to get the pressure low enough.
Hatchbackkid, do you know what the DTC associated with the CEL is? Sounds like you have an air leak. Don't forget that the silicone sealent has to sit for a few hours to harden enough to resist the vacuum at idle.
Dallas,
The TB can't ice up, as there is no fuel passing through the TB. To get normal intake air to ice up you'd need to run it through a really small venturi to get the pressure low enough.
Hatchbackkid, do you know what the DTC associated with the CEL is? Sounds like you have an air leak. Don't forget that the silicone sealent has to sit for a few hours to harden enough to resist the vacuum at idle.
I thought that is the only reason why they run hot coolant lines into the TB, in our cold climate if you bypass it you will have issues around zero, with rought running etc everyone around here calls it icing, do you know whats actually happening! I agree for ulimate performance you don't want it hot as a cooler air is more dense,
Originally Posted by jkuchta ↑The only experiance I have is with the Corolla TB, so that's the only one that I can say for sure fits.
Dallas,
The TB can't ice up, as there is no fuel passing through the TB. To get normal intake air to ice up you'd need to run it through a really small venturi to get the pressure low enough.
Hatchbackkid, do you know what the DTC associated with the CEL is? Sounds like you have an air leak. Don't forget that the silicone sealent has to sit for a few hours to harden enough to resist the vacuum at idle.
As far as I can tell, the TB is heated to give better fuel economy. Why a cold charge would cause those problems is beyond me.
I've flown injected piston aircraft is sub-zero conditions and they just seem to run stronger!
I've flown injected piston aircraft is sub-zero conditions and they just seem to run stronger!
Hey Nexus the TB has been on for 260 miles, and no problems, and the improvement is still there!
Is your TB still heated?Originally Posted by jkuchta ↑Hey Nexus the TB has been on for 260 miles, and no problems, and the improvement is still there!
it would make sense around here because it gets very cold (0 or lower) consistantly in the winter, and on the off day it will be cool and very damp. so cool and damp, temp drops, condenses on butterfly flange, engine cools down, butterfly freezes. makes sense to me for this area at least
Saggio, my TB is not heated.
Alex, it would have to be REALLY cold and VERY humid for ice to form in the TB. When a carb freezes up it is caused by the fact that fuel requires energy to vaporize...thus when fuel vaporizes it super cools the air it's in, thus causing the water vapor in the air to turn to ice. Because there is no fuel passing through the TB on our cars, there is no way the air can become supercooled enough to form ice.
The cold weather problems people are running into with unheated TB's may be caused by there being too little heat in a less-than-fully-warmed-up engine to fully vaporize the fuel in the intake port of the cylinder head, causing rough running (caused maybe by the resultant lean condition, or an over-rich ECU compensation).
This is just a theory of mine, and may not be totally correct, but I think its at least a pretty good guess😉
Alex, it would have to be REALLY cold and VERY humid for ice to form in the TB. When a carb freezes up it is caused by the fact that fuel requires energy to vaporize...thus when fuel vaporizes it super cools the air it's in, thus causing the water vapor in the air to turn to ice. Because there is no fuel passing through the TB on our cars, there is no way the air can become supercooled enough to form ice.
The cold weather problems people are running into with unheated TB's may be caused by there being too little heat in a less-than-fully-warmed-up engine to fully vaporize the fuel in the intake port of the cylinder head, causing rough running (caused maybe by the resultant lean condition, or an over-rich ECU compensation).
This is just a theory of mine, and may not be totally correct, but I think its at least a pretty good guess😉
yours makes sense, it was just what seemed logical to me
..Because there is no fuel passing through the TB on our cars, there is no way the air can become supercooled enough to form ice.welllll, maybe I should not bypass anyway, lol, because a future mod planned WILL supercool the intake air
Will this: http://cgi.ebay.com/ebaymotors/TOYOT...Q5fAccessories work with the '09 3-door HB? I'm planning to do the DIY listed in this thread, but I want to make sure this is the correct TB first.
Yup, that's the one. Great seller too, bought mine from them.