Yarisworld Archive

DIY - 1.8L 1ZZ-FE TB Connector Chip Swap

322 posts · 207,058 views · page 3 of 7

Replies continued

MGarganoNJ · Apr 9, 2009#101
Originally Posted by Gideon ↑
Yup, that's the one. Great seller too, bought mine from them.
Thanks, Gideon. So, if I'm reading this thread correctly, all I need is the 1ZZ-FE TB and the chip from my stock TB? Anything else needed to get everything working? I'm not looking to do the coolant bypass or anything.
MGarganoNJ · Apr 21, 2009#102
For those of you who did the coolant bypass, did you plug the tubes on the TB or just leave them open?
mikenacaratoBrentwood, TN · Apr 21, 2009#103
i actually pulled the tubes out with some pliers for a cleaner look and polished it up. so yes they are open.
marcustoronto, canada · Apr 21, 2009#104
WOULD THIS WORK FOR CANADIAN TB 1.5,...well im assuming it will.i may try this out...
AlexNet0Rockland, ME · Apr 21, 2009#105
Originally Posted by marcus
WOULD THIS WORK FOR CANADIAN TB 1.5,...well im assuming it will.i may try this out...
as long as the stock is a 1nz-fe engine
marcustoronto, canada · Apr 21, 2009#106
aight..i guess i got a new project to do...
MGarganoNJ · Apr 21, 2009#107
Originally Posted by mikenacarato ↑
i actually pulled the tubes out with some pliers for a cleaner look and polished it up. so yes they are open.
I capped mine. Think that's gonna make any difference?
AlexNet0Rockland, ME · Apr 21, 2009#108
^no, not unless you also capped the hoses.
MGarganoNJ · Apr 21, 2009#109
Originally Posted by AlexNet0 ↑
^no, not unless you also capped the hoses.
lol no I used one of those barb couplers. I finally broke down and did the chip swap and coolant bypass. I have the gasket maker setting overnight and look forward to testing it out tomorrow morning.
tk-421Dagobah · Apr 22, 2009#110
Originally Posted by MGargano ↑
lol no I used one of those barb couplers. I finally broke down and did the chip swap and coolant bypass. I have the gasket maker setting overnight and look forward to testing it out tomorrow morning.
Good luck! Hope that gets that problem solved on your end. 👍
I'm also considering capping the (now useless) tubes... What did you use for that?
MGarganoNJ · Apr 22, 2009#111
Originally Posted by tk-421 ↑
Good luck! Hope that gets that problem solved on your end. 👍
I'm also considering capping the (now useless) tubes... What did you use for that?
Just a few inches of rubber tubing with a little brass plug on the end. I found the plug's at Lowe's in the same section as the barb union coupler.
t0m4sPanama · Apr 22, 2009#112
did everybody trim the OEM TB gasket to allow more air flow as t-sport did?
marcustoronto, canada · Apr 22, 2009#113
[QUOTE=jkuchta;275971]As far as I can tell, the TB is heated to give better fuel economy. Why a cold charge would cause those problems is beyond me.

im assuming the high rev on cold start is due to oil being cool has to warm up ..
MGarganoNJ · Apr 22, 2009#114
No good so far. Oscillation is way worse at cold start up than before the chip swap and I got a CEL within 10 minutes of driving :(
marcustoronto, canada · Apr 22, 2009#115
Originally Posted by MGargano ↑
No good so far. Oscillation is way worse at cold start up than before the chip swap and I got a CEL within 10 minutes of driving :(
darn it!!
AlexNet0Rockland, ME · Apr 22, 2009#116
im assuming the high rev on cold start is due to oil being cool has to warm up ..
its due to the open loop during warm up, a preset throttle position untill its warm and then it uses the sensors and activly adjusts it. the opening is 30 percent larger so the preset is automatically that much higher
tk-421Dagobah · Apr 22, 2009#117
Originally Posted by AlexNet0 ↑
its due to the closed loop during warm up, a preset throttle position untill its warm and then it uses the sensors and activly adjusts it. the opening is 30 percent larger so the preset is automatically that much higher
Do you think that will have an impact on engine life and/or MPG in the end? I really like this mod, but I may not keep it if it's doing any damage...
jkuchtaL.A. · Apr 22, 2009#118
I'm still getting 37-38mpg per tank with the 1ZZ TB...and I've had it on for nearly 1000 miles so far.
AlexNet0Rockland, ME · Apr 22, 2009#119
Originally Posted by camelll ↑
I think you meant open loop during warm up.👍
lol yup *duh*
MGarganoNJ · Apr 23, 2009#120
Unless someone can convince me otherwise, I'm putting the stock TB back on tomorrow. I can handle the CEL but the oscillation is a little scary. After the chip swap, it oscillates very heavily from 2k to 3k for almost 2 minutes.
Yaris T-Sport.. · Apr 23, 2009#121
Originally Posted by MGargano ↑
Unless someone can convince me otherwise, I'm putting the stock TB back on tomorrow. I can handle the CEL but the oscillation is a little scary. After the chip swap, it oscillates very heavily from 2k to 3k for almost 2 minutes.
do this, put the stock TB back and drive it for over a week with out doing and or trying anything at all and then swap the chip back to 1zz and try it again, this helps your ecu to remember the normal setup, then give it a fresh try after that. it worked for me.
yarstarGeorgia · Apr 23, 2009#122
I concur with T-Sport. Giving it a 2nd try made it work for me too.

35-38 mpg now for 3k miles with new TB. No issues at all, except high cold idle. I really think it's worth it.
MGarganoNJ · Apr 23, 2009#123
I love the performance of the 1ZZ but the harsh oscillation is a killer. So I should reinstall the stock TB & chip for a week or so and then start over with the 1ZZ and chip swap?
yarstarGeorgia · Apr 23, 2009#124
Originally Posted by MGargano ↑
I love the performance of the 1ZZ but the harsh oscillation is a killer. So I should reinstall the stock TB & chip for a week or so and then start over with the 1ZZ and chip swap?
That worked for me. You may be getting ocillation due to an air leak. Make sure you did the gasket maker correctly and really let it set up a long time (I let mine set up overnight). Check also the intake for leaks.

I pulled mine back off, waited a week, did the chip swap again, and re-installed and have had no probs since.
MGarganoNJ · Apr 23, 2009#125
Originally Posted by yarstar ↑
That worked for me. You may be getting oscillation due to an air leak. Make sure you did the gasket maker correctly and really let it set up a long time (I let mine set up overnight). Check also the intake for leaks.

I pulled mine back off, waited a week, did the chip swap again, and re-installed and have had no probs since.
Thanks. I'll give that a try.
mikenacaratoBrentwood, TN · Apr 23, 2009#126
i just want to stress a point again. anyone who just did this mod you have to drive it for a good 2 days or so for the ecu to learn the now tb. it will oscillate bad until then.
MGarganoNJ · Apr 23, 2009#127
Originally Posted by mikenacarato ↑
i just want to stress a point again. anyone who just did this mod you have to drive it for a good 2 days or so for the ecu to learn the now tb. it will oscillate bad until then.
Oh I was under the impression that the chip swap made the oscillation and CEL go away immediately. Think I should leave it on for a few days?
marcustoronto, canada · Apr 23, 2009#128
i guess time will tell
jkuchtaL.A. · Apr 23, 2009#129
Yes....I would leave it on and see what happens.
MGarganoNJ · Apr 23, 2009#130
Originally Posted by yarstar ↑
That worked for me. You may be getting ocillation due to an air leak. Make sure you did the gasket maker correctly and really let it set up a long time (I let mine set up overnight). Check also the intake for leaks.

I pulled mine back off, waited a week, did the chip swap again, and re-installed and have had no probs since.
Did you get CEL and oscillation the first time you did the chip swap?
mikenacaratoBrentwood, TN · Apr 23, 2009#131
i did after the chip swap for a day or so. give it some time.
MGarganoNJ · Apr 23, 2009#132
Originally Posted by mikenacarato ↑
i did after the chip swap for a day or so. give it some time.
I'm gonna leave the stock one on for a week or so and then start over with the chip swap. Glad to hear I wasn't the only one having this problem.
mikenacaratoBrentwood, TN · Apr 23, 2009#133
:) mine still cold idles high for a min but it goes down to normal after that
severous01SE Texas · Apr 23, 2009#134
ok.......

here's the deal....again...for you who will listen now

you can stop the oscillation in less than ten minutes.


after the swap, pull the plug on the battery, drain caps by hitting brakes and turning on lights

plug in batt

start car AND LET IDLE FOR 10 MINUTES

you have to re-learn the iac sensor to the new throttle body...it is oscilating to learn the position of the iac motor....unless you have a vac leak somewhere.
MGarganoNJ · Apr 23, 2009#135
Originally Posted by severous01 ↑
ok.......

here's the deal....again...for you who will listen now

you can stop the oscillation in less than ten minutes.


after the swap, pull the plug on the battery, drain caps by hitting brakes and turning on lights

plug in batt

start car AND LET IDLE FOR 10 MINUTES

you have to re-learn the iac sensor to the new throttle body...it is oscilating to learn the position of the iac motor....unless you have a vac leak somewhere.
Yeah I did that... didn't help at all. I disconnected and drained the battery before I even removed the TB.
bxrichN.Y. · Apr 24, 2009#136
quick ? guys what's the diameter on the 1zz tb is it 2" & half or 3"
yarstarGeorgia · Apr 24, 2009#137
Mine's on the car, so I can't really measure it right now.

Do a search. It's on here. I think in the Performance Mod section. There's a picture of both TBs and the exact measurement of each.
bxrichN.Y. · Apr 24, 2009#138
Originally Posted by yarstar ↑
Mine's on the car, so I can't really measure it right now.

Do a search. It's on here. I think in the Performance Mod section. There's a picture of both TBs and the exact measurement of each.
will do thanks
marcustoronto, canada · Apr 24, 2009#139
been 2 days anyone got rid of the issue..
jkuchtaL.A. · Apr 24, 2009#140
I never had the issue.

I think you have an air leak somewhere in the system. Best bet is to pull the TB, and reapply the sealer and let it sit overnight to set up.
MGarganoNJ · Apr 24, 2009#141
Originally Posted by marcus ↑
been 2 days anyone got rid of the issue..
Reinstalled the 1ZZ w/ chip swap this morning with gasket sealer and coolant bypass but didn't disconnect the battery so we'll see if anything changes later today.
marcustoronto, canada · Apr 26, 2009#142
well................anyone.
MGarganoNJ · Apr 26, 2009#143
Good so far. Got oscillation on the first & second cold start but so far I'm 2 days oscillation free. I got a CEL today but took care of it with the Scangauge. I'm just glad the oscillation's gone.
PHXDEMONPhoenix, AZ · Apr 26, 2009#144
Can't wait to get my TB in the mail 🙇
MGarganoNJ · Apr 27, 2009#145
Originally Posted by kustom play ↑
my CEL kicked off today so we'll see how long that lasts for
Mine came on this morning too... got minor oscillation at cold start this morning also but nothing major.
marcustoronto, canada · Apr 29, 2009#146
bump for update...
jkuchtaL.A. · Apr 29, 2009#147
MGragano, What is the code for the CEL? Have you adjusted the idle set screw yet?
BLAZINBLUEVITZNEW YORK · Apr 29, 2009#148
9 PAGES and i still see a CEL.......
MGarganoNJ · Apr 29, 2009#149
Originally Posted by jkuchta ↑
MGragano, What is the code for the CEL? Have you adjusted the idle set screw yet?
P0505- Idle Malfunction. No, I haven't adjusted the idle screw.
jkuchtaL.A. · Apr 29, 2009#150
^

That's why you get a CEL. You MUST adjust the idle to get rid of that CEL, as it's a result of the ECU having to over-adjust to hit a target idle RPM. Re-read thread #78, and you will more than likely get rid of the CEL for good.