no you dont. i didnt touch my idle screw, its still covered in the hard crap. all i did was the chip swap, nothing else.
DIY - 1.8L 1ZZ-FE TB Connector Chip Swap
322 posts · 207,058 views · page 4 of 7
Replies continued
Cool thanks for the diy.
I got my 1zz tb from crxgames. I removed the rivets, swapped the chips, screwed them on, and added some rvt gasket maker. Plugged in the new 1zz tb with the 1nz chip and started her up. This was after I had disconnected the battery for an hour. So it started to oscilate from 2-3k like many others have mentioned. I waited for exactly 10 minutes and it ended up idling at around the same rpms as the stock tb. Drove around a bit and no cel. I didnt mess with the idle screw cause the idle was just fine. I had to run some errands and every time I started up my car no problems or cel. I have yet to start my car during a cold start up so I'll chime back in here with results. The ecu hasnt learned the changes completely yet, my auto keeps shifting too early still. I can tell theres gonna be a ton of power over 3k. I'm not sure thought, but i think i'm feeling a lot of increase in low end...@_@
Getting some headers worked on right now, should compliment the TB very well.
I got my 1zz tb from crxgames. I removed the rivets, swapped the chips, screwed them on, and added some rvt gasket maker. Plugged in the new 1zz tb with the 1nz chip and started her up. This was after I had disconnected the battery for an hour. So it started to oscilate from 2-3k like many others have mentioned. I waited for exactly 10 minutes and it ended up idling at around the same rpms as the stock tb. Drove around a bit and no cel. I didnt mess with the idle screw cause the idle was just fine. I had to run some errands and every time I started up my car no problems or cel. I have yet to start my car during a cold start up so I'll chime back in here with results. The ecu hasnt learned the changes completely yet, my auto keeps shifting too early still. I can tell theres gonna be a ton of power over 3k. I'm not sure thought, but i think i'm feeling a lot of increase in low end...@_@
Getting some headers worked on right now, should compliment the TB very well.
Mike, Mgargano's specific CEL is more than likely caused by the idle screw not being adjusted.
You MUST adjust the idle to get rid of that CELright -- read the whole sentence above, it's to get rid of a CEL. If you didn't get a CEL, you don't have to adjust it.
stock yaris 1nz tb is 2"Originally Posted by bxrich ↑quick ? guys what's the diameter on the 1zz tb is it 2" & half or 3"
1zz tb is 2.5"
i think 1nz tb is 2.25"Originally Posted by eii ↑stock yaris 1nz tb is 2"
1zz tb is 2.5"
no?
bumpin..
Pic of my 1nz tb now a paper weight on my desk <3Originally Posted by t0m4s ↑i think 1nz tb is 2.25"
no?
Picture lost · www.inimi.org
HELP!!!!!!!! PLEASE!!!!!!!! I am in the middle of installing this TB with the afe intake the issue I am having is the coupler for the intake is hitting the screws and wont go on all the way. I have tried with all my strength to push it on further with no luck. Also I am unable to wedge the hose clamp in between the coupler and the screws. Any Ideas? I was thinking about shaving out some of the inside of the coupler, but how would I go about doing it? here's a pic so you can see what I amj talking about.
Picture lost · i105.photobucket.com
Picture lost · i105.photobucket.com
and you cannot get the clamp to clamp tight just before the studs?
I have my 1ZZ installed with an AFE intake also. I bolted the TB to the intake manifold first, then slid the coupler onto the TB as far as it would go, right up to the studs. I couldn't fit a hose clamp on there either, but I've driven it about 1,000 miles with no problems. The coupler is wedged in between the intake and TB pretty tightly, so I don't think you'll have any problems with it moving/leaking. I know others are using the same TB & intake with no hose clamp, so I think you'll be fineOriginally Posted by PHXDEMON ↑HELP!!!!!!!! PLEASE!!!!!!!! I am in the middle of installing this TB with the afe intake the issue I am having is the coupler for the intake is hitting the screws and wont go on all the way. I have tried with all my strength to push it on further with no luck. Also I am unable to wedge the hose clamp in between the coupler and the screws. Any Ideas? I was thinking about shaving out some of the inside of the coupler, but how would I go about doing it? here's a pic so you can see what I amj talking about.
I tried to use a hose clamp when I did the install the first time. It stayed on for bit, but once the engine got hot, the clamp popped right off. The neck of the TB isn't long enough to clear the studs & fit a hose clamp.Originally Posted by mikenacarato ↑and you cannot get the clamp to clamp tight just before the studs?
thats why I use a bigger hose clamp
It wasn't the width/diameter that was a problem, it was the length of the TB's neck that stuck out past the studs. It was barely wider than the hose clamp itself, so it kept slipping & popping offOriginally Posted by Yaris T-Sport. ↑thats why I use a bigger hose clamp
maybe use a few zip ties?Originally Posted by MGargano ↑It wasn't the width/diameter that was a problem, it was the length of the TB's neck that stuck out past the studs. It was barely wider than the hose clamp itself, so it kept slipping & popping off
lol that thought actually occurred to me as I was typing my previous post. Like I said, I haven't had any problems not having the clamp, but if I do I'll use a strong zip tieOriginally Posted by Yaris T-Sport. ↑maybe use a few zip ties?
I guess ill just run in without the clamp and cross my fingers
get 3 more bolts like the one lower left bolt and replace the 3 studs.
Just finished the install and holy fucking oscillation 😢 form 1000-3000 rpm from a cold start. I tried driving around a little bit and it started jumping up to 4k on idle 🙁 and a CEL. How long does it typically take for the oscillation to start smoothing out? It's too late here (9:15) to mess around with it more. Don't want to piss off the neighbors. Any suggestions?
It took about 2 days or so for the oscillation & CEL to finally go away
I am doing to leave the battery disconnected overnight incase 2 hours wasnt enough.
Did the oscillation slowly smoothe out or did it just stop out of nowhere? How much driving did you do in 2 days?Originally Posted by MGargano ↑It took about 2 days or so for the oscillation & CEL to finally go away
I got oscillation at cold idle as well as intermittent CEL for the first two days, then both just went away completely. All I get now is the high (3,000 RPM) cold idle and better performance. I only did local driving during those first few days, no highway or any heavy pushing.
Damn I was still gettingm oscillation and my motor was getting pretty warm. Is there an an idiot light that turns on if it starts overheating?Originally Posted by MGargano ↑I got oscillation at cold idle as well as intermittent CEL for the first two days, then both just went away completely. All I get now is the high (3,000 RPM) cold idle and better performance. I only did local driving during those first few days, no highway or any heavy pushing.
WTF I just hooked the battery back up and started it up again and my idle was perfect with no oscillation 🙇 Hopefully it stays that way. I didn't want to even take it around the block because I have had about half a beer and their are mad cops out for cinco de mayo. Hopefully I will have a nice drive to work tomorrow
Don't be surprised if the oscillation comes and goes for the first couple days. This happened to me and I thought everything was fine, then I got oscillation on the next cold start. Just be patient and give it a few days to work itself out.Originally Posted by PHXDEMON ↑WTF I just hooked the battery back up and started it up again and my idle was perfect with no oscillation
No clamp for months now on mine and no problems.Originally Posted by PHXDEMON ↑I guess ill just run in without the clamp and cross my fingers
Yeah it came back 🙁Originally Posted by MGargano ↑Don't be surprised if the oscillation comes and goes for the first couple days. This happened to me and I thought everything was fine, then I got oscillation on the next cold start. Just be patient and give it a few days to work itself out.
Just out of curiousity, are you guys doing the coolant bypass? I was considering doing so unless this changes the way it idles. The 3k cold starts for 1 minute is all I want as far as weird reving goes. Dont want the bypass to screw with my fine idling.
I did do the coolant bypass. Drive to work today was great . I actually don't experience the high cold idle everyone else is. My cold idle is around 2k RPM just like stock. I did hower buy my TB from M911gt on here so he may have fine tuned the idle screw. I think if anything doing the coolant bypass will make it idle better 🤷Originally Posted by eii ↑Just out of curiousity, are you guys doing the coolant bypass? I was considering doing so unless this changes the way it idles. The 3k cold starts for 1 minute is all I want as far as weird reving goes. Dont want the bypass to screw with my fine idling.
Just to clarify things, the coolant by pass i just just hooking up together the two coolant hoses that connect to the TB, right? You dont do anything to the little metal thingies on the TB the hoses were connected to? Just leave them be?Originally Posted by PHXDEMON ↑I did do the coolant bypass. Drive to work today was great . I actually don't experience the high cold idle everyone else is. My cold idle is around 2k RPM just like stock. I did hower buy my TB from M911gt on here so he may have fine tuned the idle screw. I think if anything doing the coolant bypass will make it idle better 🤷
I plugged the tubes on the TB, but I've heard others have left them as-is. And yes, you just have to use a barb union to join the two hoses together.Originally Posted by eii ↑Just to clarify things, the coolant by pass i just just hooking up together the two coolant hoses that connect to the TB, right? You dont do anything to the little metal thingies on the TB the hoses were connected to? Just leave them be?
Correct others have plugged them I just left them as is. Just go down to a lowes/home depot/etc and get a coupler barb for 3/8 inch ID vinyl tubing and you are food to roll. Stock clamps work and everything just need the barb.Originally Posted by eii ↑Just to clarify things, the coolant by pass i just just hooking up together the two coolant hoses that connect to the TB, right? You dont do anything to the little metal thingies on the TB the hoses were connected to? Just leave them be?
Cool thanks guys. I'll probably stop by lowes once my paycheck arrives, hazzah!
Also, I'm using the simotoa carbon charger CAI. Buy a 2.5" silicone coupler at your local auto parts store and that should work perfectly.
Also, I'm using the simotoa carbon charger CAI. Buy a 2.5" silicone coupler at your local auto parts store and that should work perfectly.
So judging by the 186 post, no one has figured this out yet. I had this on my car and could not figure out how to turn the CEL off. I just came to the conclusion that just b/c a part fits on my car doesn't mean it belongs on there. I think there are only a handful of members that have done this mod sucessfully(i.e. No oscillation, no CEL)
hey guys would the 1zz-fe from toyota matrix works as well???
^ same one as the corolla
Kustom...what is the CEL code?
I am still getting oscillation like a motherfucker (1-4k RPM) but no CEL. Hey kustom I'll trade you my oscillation for your CEL. I pulled up next to a STI yesterday and looked like some faggot ricer revving my engine. I am debating just throwing my stock exhaust back on so it isn't as obvious that my engine is revving.
lolz.. this thing can get you in trouble..imagine lining up with a copper on a stop light...Originally Posted by PHXDEMON ↑I am still getting oscillation like a motherfucker (1-4k RPM) but no CEL. Hey kustom I'll trade you my oscillation for your CEL. I pulled up next to a STI yesterday and looked like some faggot ricer revving my engine. I am debating just throwing my stock exhaust back on so it isn't as obvious that my engine is revving.
I started killing my engine at stop lights 😆 I bled the coolant today and it didn't make a difference. It seriously seems like the oscillating is getting worse and it is pissing me off. I am going to make one final attempt to reseal/remount the TB and let it set for 24 hours while the battery is disconnected and if it is still giving me crap after a couple days I'm just pulling this fucker off. Also I tried the whole rev the engine up to 5k for 3 minutes thing but after 2 minutes my engine started backfiring so I stopped.Originally Posted by marcus ↑lolz.. this thing can get you in trouble..imagine lining up with a copper on a stop light...
Maybe you have a bad TB or the idle screw was messed with too much? (I didn't bother touching mine.)
I never did the chip swap on mine (too lazy). Coolant bypass (didn't bother to bleed it) and only have high idle when cold and of course my CEL is always on. (For about 700 miles now)
Mine does stick a bit it seems, RPMs hang for a few when slowing quickly to a stop (usually to go over speedbumps).
No oscillation, except when I first installed it. That was fun trying to avoid looking like a douchebag revving at every light. (For the 100 miles I had that issue I would just put the car into gear quickly to bring the car's RPMs down to normal and then release.)
I never did the chip swap on mine (too lazy). Coolant bypass (didn't bother to bleed it) and only have high idle when cold and of course my CEL is always on. (For about 700 miles now)
Mine does stick a bit it seems, RPMs hang for a few when slowing quickly to a stop (usually to go over speedbumps).
No oscillation, except when I first installed it. That was fun trying to avoid looking like a douchebag revving at every light. (For the 100 miles I had that issue I would just put the car into gear quickly to bring the car's RPMs down to normal and then release.)
Yup I get the stuck throttle at times as well. Cold idle too, but no CEL yet.Originally Posted by Gideon ↑Mine does stick a bit it seems, RPMs hang for a few when slowing quickly to a stop (usually to go over speedbumps).
Originally Posted by Gideon ↑Maybe you have a bad TB or the idle screw was messed with too much? (I didn't bother touching mine.)
I never did the chip swap on mine (too lazy). Coolant bypass (didn't bother to bleed it) and only have high idle when cold and of course my CEL is always on. (For about 700 miles now)
Mine does stick a bit it seems, RPMs hang for a few when slowing quickly to a stop (usually to go over speedbumps).
No oscillation, except when I first installed it. That was fun trying to avoid looking like a douchebag revving at every light. (For the 100 miles I had that issue I would just put the car into gear quickly to bring the car's RPMs down to normal and then release.)
🤷 I bought the TB off of m911gt who was selling it because of the same issue. I did the chip swap on it so that rules out a bad chip. Fucking with the idle screw is the only thing I have yet to do because I don't see why that would cause anything other than a too high/too low idle. Plus after I installed it I drove to work and back (50 mile round trip) and it ran flawlessly other than hanging to RPMs a little bit but it sure as hell wasnt oscillating. Also this entire time I have yet to actually get a check engine light 😕 You would tend to think with the motor ranging from 1-3/4k rpm it would throw a code. I think my ECU is just being a stuck up whore 😠
Also Gideon did yours oscillate right off the start? Did it come and go? Or was it just oscillation constant for first 100 miles and then it went away? How hard did you drive it for thos efirst 100?
Possibly you guys running with CELs are in open loop vs closed loop and that's why you aren't getting oscillation 🤷
Yeah, it oscillated every time I let the engine go back to idle initially and it was for only 20 miles or so. In that 20 miles I ran it to redline every chance I could. (After the engine was properly warmed up of course)Originally Posted by PHXDEMON ↑Also Gideon did yours oscillate right off the start? Did it come and go? Or was it just oscillation constant for first 100 miles and then it went away? How hard did you drive it for thos efirst 100?
So I need to start driving like a ricer Also was it really jerky every time you applied/let off the gas? Like on the freeway I hit the gas but it steadily accelerates so I have to let off and every time I take my foot off/put it back on the gass it jerks like a motherfucker.Originally Posted by Gideon ↑Yeah, it oscillated every time I let the engine go back to idle initially and it was for only 20 miles or so. In that 20 miles I ran it to redline every chance I could. (After the engine was properly warmed up of course)
Yeah it was pretty jerky initially.
It still is really jerky if the engine is cold, but once it warms up it ceases.
It still is really jerky if the engine is cold, but once it warms up it ceases.
Mine keeps getting worse and worse. Jerky as fuck even when the sngine is warm and the oscillation is progressively getting worse. 🙁Originally Posted by Gideon ↑Yeah it was pretty jerky initially.
It still is really jerky if the engine is cold, but once it warms up it ceases.