Yarisworld Archive

Yaris Dyno charts

260 posts · 848,025 views · page 4 of 6

Replies continued

ilikericesavannah, ga · May 12, 2012#151
holy shit balls batman!

and the winner goes tooo
vtencolumbus · May 12, 2012#152
Holy batman robin n iron man ...

500 plus on a Yaris ... Even on my AMG with double the Yaris weight I get scared sometimes with the traction control off ....
GolddeenohColumbia, SC · May 12, 2012#153
holy sheeeet 32psi. big boost there big pimpin.
cali yarisCanoga Park, CA · May 12, 2012#154
holy Avengers...

what's "avgas"? some kind of race gas, I'm guessing?
changchewsoonMalaysia · May 12, 2012#155
We call them avgas on our part of the world, perhaps it's better known as aviation fuel on your side?
GolddeenohColumbia, SC · May 12, 2012#156
ahh we tend to call it "Jet Fuel" and depending on the grade maybe even "Race Fuel" or "Race Gas".
thebarberGrand Rapids, MI · May 13, 2012#157
Originally Posted by cali yaris ↑

Any idea why the power is so much higher than the torque? The gap between the two seems to grow the higher you go with boost and power.
I'm guessing turbo choice...

And HP = (tq x rpm) / 5252....so at high rpm you need less tq for big hp
cali yarisCanoga Park, CA · May 13, 2012#158
I don't see how he could have much more than a GT30 back there.
thebarberGrand Rapids, MI · May 13, 2012#159
455whp at 8300rpm = 288wtq at 8300rpm

501whp at 8300rpm = 317wtq at 8300rpm

When peak HP is at such high rpm, you don't need to make a ton of tq up high (relative to HP, that is)

My vibe's 2zzge is 180hp at like 7600rpm and 130tq at 6800rpm...
Hussain-VtecBahrain · Jun 27, 2012#160
Originally Posted by changchewsoon ↑
After running in the engine, I had the car sent back for a tune today and things got interesting.

Blue curve - 404 whp, previous base tuning for engine run in, pump gas, 1.6 bar boost, no water/meth.

Red curve - 454 whp, pump gas, 1.7 bar boost, water/meth turned on.

Green curve - 501 whp, pump gas + avgas 50/50 mixture, 2.2 bar, no water/meth.
That Nice Curves in Both Congrats.
Time to
tooterLos Angeles · Jul 5, 2012#161
That's a tough act to follow!😆

Here's the results of my baseline dyno runs.

Picture not included in this copy

The engine is bone stock except for:

Weapon R Short Ram Intake with BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Exhaust Header
Mirco Image MagnaFlow Center Exit Exhaust

100 horsepower and 100 foot pounds is not too bad considering just those few mods. 🙂

The torque curve is pretty flat overall and peaks at 4,000 rpm.
Hussain-VtecBahrain · Jul 7, 2012#162
Originally Posted by tooter ↑
That's a tough act to follow!😆

Here's the results of my baseline dyno runs.

The engine is bone stock except for:

Weapon R Short Ram Intake with BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Exhaust Header
Mirco Image MagnaFlow Center Exit Exhaust

100 horsepower and 100 foot pounds is not too bad considering just those few mods. 🙂

The torque curve is pretty flat overall and peaks at 4,000 rpm.
That is Nice.
Question what Do you use for tuning your ECU?

Do you have any idea About the Camcon VVT-I Controller
Picture not included in this copy
I hear its a nice tuning device.
tooterLos Angeles · Jul 7, 2012#163
Originally Posted by Hussain-Vtec ↑
That is Nice.
Question what Do you use for tuning your ECU?
What tuning? 😆

I just ran the car as it was. However, I did disconnect the battery after putting on the short ram intake so that the ECU had plenty of runing time to readjust to the new operating conditions.

Harry did 4th gear pulls that you could time with a calendar! 😆

After the first one, he asked if I wanted third gear pulls, but I wanted all the pulls to be done under exactly the same conditions to get consistent results.
Hussain-VtecBahrain · Jul 7, 2012#164
Originally Posted by tooter ↑
What tuning? 😆

I just ran the car as it was. However, I did disconnect the battery after putting on the short ram intake so that the ECU had plenty of runing time to readjust to the new operating conditions.

Harry did 4th gear pulls that you could time with a calendar! 😆

After the first one, he asked if I wanted third gear pulls, but I wanted all the pulls to be done under exactly the same conditions to get consistent results.
Oh😆
That is great Tooter,

My Engine is JDM 2NZ-FE 1.3 I have to do some new moods to it.
for now i am shocked from it, I Did Some few Rolling races with the 2011 Corolla till fifth gear he cant pas my echo ?

OEM header, 2" down piping with out the cat, custom 2'' Exhaust muffler, square K&N air filter in the oem filter Box.
cali yarisCanoga Park, CA · Jul 7, 2012#165
3rd gear would have been cheating anyway. 😉
BEEFnorth carolina · Jul 7, 2012#166
Isn't 4th gear 1:1? isn't that the best power transfer?
tooterLos Angeles · Jul 7, 2012#167
Does third gear record a different horsepower number? If it does, I only want accurate numbers, not pumped up ones. The 4th gear pulls took so l-o-n-g and the engine barely made it up to redline, I was laughing! 😆
tooterLos Angeles · Jul 7, 2012#168
Originally Posted by BEEF ↑
Isn't 4th gear 1:1? isn't that the best power transfer?
You can tell from the video that it took so long to wind out the engine I thought it wasn't going to make it up to redline.

http://www.youtube.com/watch?v=rYF6pvhn96U

I don't think that Harry believed it would make it either. He said that most dyno runs are about 8 seconds. Mine were over 30 seconds. 😆
1.5Tampa · Jul 7, 2012#170
I was always under the impression that 4th gear pulls were standard for dyno. Not sure why though.
tooterLos Angeles · Jul 7, 2012#171
Originally Posted by 1.5 ↑
I was always under the impression that 4th gear pulls were standard for dyno. Not sure why though.
Maybe it's because 4th is usually 1 to 1 gearing like BEEF said. It just was so funny how long it took to wind up because the little engine doesn't make much power.
1.5Tampa · Jul 7, 2012#172
lol yeah did you have to pay the tech overtime so he could finish the pull lol
cali yarisCanoga Park, CA · Jul 7, 2012#173
1 to 1 is the most accurate, and the pull is long enough to record with precision -- in tooter's case, great precision. 😆

The pull above on mine was to 7300 rpm, 1000 over where the stock limiter kicks in.
tooterLos Angeles · Jul 7, 2012#174
Originally Posted by cali yaris ↑
1 to 1 is the most accurate, and the pull is long enough to record with precision -- in tooter's case, great precision. 😆

The pull above on mine was to 7300 rpm, 1000 over where the stock limiter kicks in.
Yeah, the computer had plenty to time to record every nuance of power fluctuation in infinite detail. 😆

Harry, the owner was very kind, patient, and helpful as we spent quite a bit of time talking about the principles governing intake manifolds.

I left his dyno shop more educated than when I arrived. 🙂
tooterLos Angeles · Jul 7, 2012#175
Originally Posted by 1.5 ↑
lol yeah did you have to pay the tech overtime so he could finish the pull lol
Yeah, the engine was still trying to hit redline when Harry told the guys to close up the shop and go home... he'd stay overnight hoping the run would be done by sunup. 😆
cali yarisCanoga Park, CA · Jul 7, 2012#176
you're funny, tooter 😆
why?harnett county NC · Jul 7, 2012#177
Tooter, some pulleys and lightweight wheels would make that less painful, and add a couple hp to get over 100 as well.
tooterLos Angeles · Jul 7, 2012#178
There's no pain in getting an honest accurate measurement of the power that the engine actually produces. 🙂 The point isn't to enhance the results but to obtain two relative results where the intake manifold is the only change.

And that heavy pully on the front does serve a purpose. They used to be called harmonic balancers. The flywheel weight on the front helps to minimize the twisting forces exerted on the crankshaft by the flywheel weight on the rear.

I visited the CNC guys today and we went over details and clearances using the 3D image generation of the flange. The intake manifold flange will have a small 3mm deep inset where the runners of the manifold can be inserted to hold them in proper position while they're being welded on. The thickness of the shelf will match the thickness of the runner tubing so that the interior remains uniform. Any slight imperfections I can smooth out from the inside with a Dremel. The computer automatically generates a seamless transition within the one inch thick flange between the intake runners on the Corolla manifold and the intake ports of the Yaris head. 👍
Hussain-VtecBahrain · Jul 8, 2012#179
Actually thy run it in the forth Gear to avoid wheel spin for F/I cars, for N/A i will Run it in
Third @ very low RPM Like 1500 or so.
thebarberGrand Rapids, MI · Jul 8, 2012#180
They actually try to choose the gear closest to 1:1

I ran all of mine in 3rd. 4th, iirc, hits the speed limiter before redline
Hussain-VtecBahrain · Jul 8, 2012#181
Originally Posted by tooter ↑
Does third gear record a different horsepower number? If it does, I only want accurate numbers, not pumped up ones. The 4th gear pulls took so l-o-n-g and the engine barely made it up to redline, I was laughing! 😆
IN N/A Cars i do no but in F/I cars there are some differences in WHP.
Hussain-VtecBahrain · Jul 8, 2012#182
Originally Posted by why? ↑
Tooter, some pulleys and lightweight wheels would make that less painful, and add a couple hp to get over 100 as well.
Things you Need to Learn about crank Pulleys, Hope that help guys Enjoy reading IT!

Link
http://www.atiracing.com/products/da...mper_dinan.htm
Hussain-VtecBahrain · Jul 8, 2012#183
Originally Posted by thebarber ↑
They actually try to choose the gear closest to 1:1

I ran all of mine in 3rd. 4th, iirc, hits the speed limiter before redline
OK I No the ratio thing but here is an example.

Here was a comparison of 4th gear and 5th gear on S2000. 5th has more torque, 4th has more horsepower.

As you no the S2000 have a 6 speed Trans.

If its a 5 speed trans it will be different as i state 3third N/A 4Forth F/I.

Picture not included in this copy

And if you notice there in dyno sheet above in 4forth gear the graf line is smoother.
Hussain-VtecBahrain · Jul 8, 2012#184
Here is another Examples For Toyota Supra.

The reason to share it with you i want you to see the A/F ratio Differences Between
the runs That's cause Thy tuned at 3rd gear, 4-5th gear pulls the a/f were completely wacked Because of load will do that.

Top speed in 3rd, 4th, and 5th gear (with dyno sheets)
This is with timing set at 7 degrees and 17psi.

3rd Gear:
Picture not included in this copy

4th Gear:
Picture not included in this copy

5th Gear:
Picture not included in this copy

Enjoy ALL.

3 attachments not included in this copy

why?harnett county NC · Jul 8, 2012#185
lots of scientific sounding stuff with zero proof. Here's something from someone who knows what he is talking about.

Q. Will NST Pulleys lead to premature engine failure?


Oh and if lightweight pulleys,"often produce severe damage," prove it. You should be able come up with many examples of this severe damage if it happens often...
Originally Posted by Hussain-Vtec ↑
Things you Need to Learn about crank Pulleys, Hope that help guys Enjoy reading IT!

The Danger of Power Pulleys &
Understanding the Harmonic Damper

BY STEVE DINAN OF DINAN BMW

I have been threatening for a long time to write a series of technical articles to educate consumers and to dispel misconceptions that exist about automotive after-market technology. Motivated by problems with customer's cars resulting from the installation of power pulleys, I wish to explain the potential dangers of these products and address the damage they cause to engines.

The theory behind the power pulley is that a reduction in the speed of the accessory drive will minimize the parasitic losses that rob power from the engine. Parasitic power losses are a result of the energy that the engine uses to turn accessory components such as the alternator and water pump, instead of producing power for acceleration. In an attempt to minimize this energy loss, many companies claim to produce additional power by removing the harmonic damper and replacing it with a lightweight assembly. While a small power gain can be realized, there are a significant number of potential problems associated with this modification, some that are small and one which is particularly large and damaging!

The popular method for making power pulleys on E36 engines is by removing the harmonic damper and replacing it with a lightweight alloy assembly. This is a very dangerous product because this damper is essential to the longevity of an engine. The substitution of this part often results in severe engine damage.

It is also important to understand that while the engine in a BMW is designed by a team of qualified engineers, these power pulleys are created and installed by people who do not understand some very important principles of physics. I would first like to give a brief explanation of these principles which are critical to the proper operation of an engine.

1) Elastic Deformation
Though it is common belief that large steel parts such as crankshafts are rigid and inflexible, this is not true. When a force acts on a crank it bends, flexes and twists just as a rubber band would. While this movement is often very small, it can have a significant impact on how an engine functions.

2) Natural Frequency
All objects have a natural frequency that they resonate (vibrate) at when struck with a hammer. An everyday example of this is a tuning fork. The sound that a particular fork makes is directly related to the frequency that it is vibrating at. This is its "natural frequency," that is dictated by the size, shape and material of the instrument. Just like a tuning fork, a crankshaft has a natural frequency that it vibrates at when struck. An important aspect of this principle is that when an object is exposed to a heavily amplified order of its own natural frequency, it will begin to resonate with increasing vigor until it vibrates itself to pieces (fatigue failure).

3) Fatigue Failure
Fatigue failure is when a material, metal in this case, breaks from repeated twisting or bending. A paper clip makes a great example. Take a paper clip and flex it back and forth 90° or so. After about 10 oscillations the paper clip will break of fatigue failure.

The explanation of the destructive nature of power pulleys begins with the two basic balance and vibration modes in an internal combustion engine. It is of great importance that these modes are understood as being separate and distinct.

1) The vibration of the engine and its rigid components caused by the imbalance of the rotating and reciprocating parts. This is why we have counterweights on the crankshaft to offset the mass of the piston and rod as well as the reason for balancing the components in the engine.

2) The vibration of the engine components due to their individual elastic deformations. These deformations are a result of the periodic combustion impulses that create torsional forces on the crankshaft and camshaft. These torques excite the shafts into sequential orders of vibration, and lateral oscillation. Engine vibration of this sort is counteracted by the harmonic damper and is the primary subject of this paper.

Torsional Vibration (Natural Frequency)

Every time a cylinder fires, the force twists the crankshaft. When the cylinder stops firing the force ceases to act and the crankshaft starts to return to the untwisted position. However, the crankshaft will overshoot and begin to twist in the opposite direction, and then back again. Though this back-and-forth twisting motion decays over a number of repetitions due to internal friction, the frequency of vibration remains unique to the particular crankshaft.

This motion is complicated in the case of a crankshaft because the amplitude of the vibration varies along the shaft. The crankshaft will experience torsional vibrations of the greatest amplitude at the point furthest from the flywheel or load.

Picture not included in this copy

Harmonic (sine wave) Torque Curves
Each time a cylinder fires, force is translated through the piston and the connecting rod to the crankshaft pin. This force is then applied tangentially to, and causes the rotation of the crankshaft.

The sequence of forces that the crankshaft is subjected to is commonly organized into variable tangential torque curves that in turn can be resolved into either a constant mean torque curve or an infinite number of sine wave torque curves. These curves, known as harmonics, follow orders that depend on the number of complete vibrations (cylinder pulses) per revolution. Accordingly, the tangential crankshaft torque is comprised of many harmonics of varying amplitudes and frequencies. This is where the name "harmonic damper" originates.

Picture not included in this copy

Critical RPM's
When the crankshaft is revolving at an RPM such that the torque frequency, or one of the harmonic sine wave frequencies coincides with the natural frequency of the shaft, resonance occurs. Thus, the crankshaft RPM at which this resonance occurs is known a critical speed. A modern automobile engine will commonly pass through multiple critical speeds over the range of its possible RPM's. These speeds are categorized into either major or minor critical RPM's.

Major and Minor Critical RPM’s
Major and minor critical RPM's are different due to the fact that some harmonics assist one another in producing large vibrations, whereas other harmonics cancel each other out. Hence, the important critical RPM’s have harmonics that build on one another to amplify the torsional motion of the crankshaft. These critical RPM’s are know as the "major criticals". Conversely, the "minor criticals" exist at RPM's that tend to cancel and damp the oscillations of the crankshaft.

If the RPM remains at or near one of the major criticals for any length of time, fatigue failure of the crankshaft is probable. Major critical RPM’s are dangerous, and either must be avoided or properly damped. Additionally, smaller but still serious problems can result from an undamped crankshaft. The oscillation of the crankshaft at a major critical speed will commonly sheer the front crank pulley and the flywheel from the crankshaft. I have witnessed front pulley hub keys being sheered, flywheels coming loose, and clutch covers coming apart. These failures have often required crankshaft and/or gearbox replacement.

Harmonic Dampers
Crankshaft failure can be prevented by mounting some form of vibration damper at the front end of the crankshaft that is capable of absorbing and dissipating the majority of the vibratory energy. Once absorbed by the damper the energy is released in the form of heat, making adequate cooling a necessity. This heat dissipation was visibly essential in Tom Milner's PTG racing M3 which channeled air from the brake ducts to the harmonic damper, in order to keep the damper at optimal operating temperatures. While there are various types of torsional vibration dampers, BMW engines are primarily designed with "tuned rubber" dampers.

Picture not included in this copy

It is also important to note that while the large springs of a dual mass flywheel absorb some of the torsional impulses conveyed to the crankshaft, they are not harmonic dampers, and are only responsible for a small reduction in vibration.

In addition to the crankshaft issue, other problems can result from slowing down the accessories below their designed speeds, particularly at idle. Slowing the alternator down can result in reduced charging of the battery, dimming of the lights, and computer malfunctions. Slowing of the water pump and fan can result in warm running, while slowing of the power steering can cause stiff steering at idle and groaning noises. It is possible to implement design corrections and avoid these scenarios, but this would require additional components and/or software.
Our motto at Dinan is "Performance without sacrifice" We feel our customers expect ultra high performance along with the legendary comfort and reliability of a standard BMW.

While it is common that a Dinan BMW is the fastest BMW you can buy, performance is not our only goal. Dinan isn't just trying to make the fastest car. Instead a host of considerations go into the development of our products. Dinan puts much more effort into these other areas than does our competition.
These considerations are Performance, Reliability (Warranty), Driveability, Emissions, Value, Fit and Finish. We feel that the power pulley is a bad way to get extra power from and engine and the potential for serious engine damage is too great.

This is a simplified explanation meant to be comprehensible by those who are not automotive engineers. In trying to simplify an extremely complex topic some precision was sacrificed although we believe this explanation to be as accurate as possible. We encourage our customers to educate themselves and understand the automotive after-market because we believe that our products are the best researched, engineered, and fabricated products available.

For those interested in a more in depth and technical explanation of this topic, the reference book is Advanced Engine Technology, written by Heinz Heisler MSc,BSc,FIMI,MIRTE,MCIT. Heinz Heisler is the Head of Transportation Studies at The College of North West London. His book is distributed in this country by the SAE (Society of Automotive Engineers).

Link
http://www.atiracing.com/products/da...mper_dinan.htm
tooterLos Angeles · Jul 8, 2012#186
Originally Posted by why? ↑
lots of scientific sounding stuff with zero proof. Here's something from someone who knows what he is talking about.

Q. Will NST Pulleys lead to premature engine failure?


Oh and if lightweight pulleys,"often produce severe damage," prove it. You should be able come up with many examples of this severe damage if it happens often...
I've just been reading up on this by Googling the topic, and there are views on all sides of this issue just like the views on breaking in an engine. How about another oil thread? What cures hiccups? 😆
cali yarisCanoga Park, CA · Jul 9, 2012#187
how about we stay on topic? I thought this was a dyno chart thread.
tooterLos Angeles · Jul 9, 2012#188
Good point. Maybe a mod could move the posts to another thread.
Hussain-VtecBahrain · Jul 9, 2012#189
Originally Posted by why? ↑
lots of scientific sounding stuff with zero proof. Here's something from someone who knows what he is talking about.

Q. Will NST Pulleys lead to premature engine failure?


Oh and if lightweight pulleys,"often produce severe damage," prove it. You should be able come up with many examples of this severe damage if it happens often...
First Of All the write up I Op made by STEVE DINAN OF DINAN BMW Of Dinan Motor sport.

I Don't have to prove any thing for you, Do your own search and proves,
The reason i share it with you guys to ad more Knowledge to This thread.
And please don't Quote the whole post i did its taking lots of space.
Thank you.
And Do some Google search about the guy if you want some prove.


Originally Posted by cali yaris ↑
how about we stay on topic? I thought this was a dyno chart thread.
Agree with you and Sorry to post that just wanted to help.
why?harnett county NC · Jul 9, 2012#190
you posted it, you have to back it up. I already know it is bs, and pulley's don't cause issues, never mind a 2 mm piece of rubber actually doing anything at all.

Have had a pulley set for 10,000 miles, and not 1 issue.

Originally Posted by Hussain-Vtec ↑
First Of All the write up I Op made by STEVE DINAN OF DINAN BMW Of Dinan Motor sport.

I Don't have to prove any thing for you, Do your own search and proves,
The reason i share it with you guys to ad more Knowledge to This thread.
And please don't Quote the whole post i did its taking lots of space.
Thank you.
And Do some Google search about the guy if you want some prove.




Agree with you and Sorry to post that just wanted to help.
Hussain-VtecBahrain · Jul 9, 2012#191
Originally Posted by why? ↑
you posted it, you have to back it up. I already know it is bs, and pulley's don't cause issues, never mind a 2 mm piece of rubber actually doing anything at all.

Have had a pulley set for 10,000 miles, and not 1 issue.
I No that i post it and i am Experience with it, the rubber you are making fun of it will balance the engine due from unwanted vibration, ask your self this why the hell most of drag race Engines have ATI Damper,
Here is a simple answer that is to balance it also it can save The trans as well and To rive more RPM's and not to be afraid about it.
eTiMaGoThread starterBangkok, Thailand · Jul 9, 2012#192
from what I understand, V engines are more prone to harmonic imbalance, for which a rubber damper is a good idea. But for a modern, "weak" I4, it would not make a difference...
tooterLos Angeles · Jul 9, 2012#193
Originally Posted by eTiMaGo ↑
from what I understand, V engines are more prone to harmonic imbalance, for which a rubber damper is a good idea. But for a modern, "weak" I4, it would not make a difference...
As a kid in auto shop I was taught that harmonic balancers served a useful purpose... but that was when dinosaurs roamed the earth! 😆 The long crankshafts of inline "straight six" cylinder engines (used to be as common as 4 cyl engines are now) especially benefitted from having a damper. Maybe with improved metallurgy, more precise balancing, and smaller shorter engines today it's not as important as it used to be.
fnkngrvIn The Hotbox · Jul 10, 2012#194
So yesterday I went back down to Granite State Dyno and Tune ( http://granite-state-dyno.com/ ) with Tiamat with the new setup. Major changes even if they do not impact on the dyno are as follows from my previous dyno pulls referenced ( http://www.microimageonline.com/foru...ll=1#post61914 ) :

- NST Cage Bushings and engine compartment linkage bushings
- NST in cabin short shifter
- Micro Image shifter linkage bracket
- Micro Image silicone radiator hose set
- Autometer Fuel Pressure Gauge kit
- CCI Lightweight Flywheel
- CCI Stage 3 clutch kit
- Tial MV-S External Wastegate
- Grimmspeed Universal Manual Boost Controller
- ARP Exhaust Manifold Bolts
- Changed all fluids to AMSOIL
- 7/8psi of boost
- Running XXR 508s with Diamondback 225/4018s (previously 15" steelies with 195/60/15s)
- Ambient temp ~95 degrees F and 22% himidity (previously ~80 degrees F and 5% humidity)



Picture not included in this copy
Picture not included in this copy
tooterLos Angeles · Jul 10, 2012#195
Your dyno chart starts where mine ends.😆
tooterLos Angeles · Nov 26, 2012#196
Today I ran back to back runs with the stock manifold and the tooter. Both ran with the same BLOX velocity stack intake...

Picture not included in this copy

Stock manifold is red011, and tooter is blue014...



Picture not included in this copy
AddoPakistan · Nov 27, 2012#197
3SGTE

1 attachment not included in this copy

FHT_RacingHouston, TX · Apr 7, 2013#198
All stock USDM '09 3DR Hatch 5spd. 38k miles. 3rd gear on DynoJet.

Picture not included in this copy
FHT_RacingHouston, TX · Apr 7, 2013#199
Originally Posted by FHT_Racing ↑
All stock USDM '09 3DR Hatch 5spd with 38k miles. Back to back 3rd gear runs on DynoJet dyno.

Picture not included in this copy
103hp/103trq
101hp/101trq
100hp/102trq

Thanks,

Andrew
KTSTrinidad and Tobago · Sep 14, 2013#200
2007 Vitz RS Manual
Stock 1NZFE 1.5L
85.27 whp / 81.18 ft-lbs
Located in Trinidad and Tobago
Picture not included in this copy
Picture not included in this copy

2 attachments not included in this copy