Just wanted to check back in a let the community know that the Yaris intake is still on. I have been using my Yaris to help get the low-buck turbo kit done and we had good success running at 4-5 psi level (good power and no CELs). Unfortunately we lost a rod while running higher boost levels and that leaves me with no motor to develope the intake manifold-we have removed the damaged motor and are doing a forged rod and psiton combo (hopefully with Garm's assistance). I need a Yaris to complete the production version of the intake to make it available for sale. Whoever suplies the car (for 7-10 days) will receive a free intake (in So Cal-Vegas Area). Let me know if there is interest.
Yaris Intake Manifold
201 posts · 92,195 views · page 1 of 5
Replies 200
i would make you use mine but i live way in florida and its my dd
i will volunteer i live in vegas but this car is my dd.. hmm let me think this over. :)
damm east coast misses out AGAIN......
Hitch a ride for a week, this is a $700 free part...Originally Posted by pinoypizzaboy ↑i will volunteer i live in vegas but this car is my dd.. hmm let me think this over. :)
i know right i use this car to deliver pizzas. 1 week without it i lose 700 in tips and pay. hmm decisions 😕Originally Posted by PetersRedYaris ↑Hitch a ride for a week, this is a $700 free part...
use a bike :D
ricky bobby style
ricky bobby style
Here we go again..... 😁
I believe the test car will actually be needed in Palmdale, CA.
Maybe it would be best to use Cali's car so he can then report to the members about performance. fitment etc...We will perform a back-to-bac test on the intake both on turbo and NA application. Production run of 10 intakes will be done by end of NOV.
So what happened with the xD intake?
Any hopes that one will be seeing the light of day?
I knew of a few people interested but due to your long and quite absence we totally forgot about it... 🙁
Please post here if the possiblity of a group buy comes up.
Intake Mani
Any hopes that one will be seeing the light of day?
I knew of a few people interested but due to your long and quite absence we totally forgot about it... 🙁
Please post here if the possiblity of a group buy comes up.
Intake Mani
my car is available if you still need one!🙂
Good to see you back, I've been waiting patiently for this manifold. I live in Northern California and which I could help but, I'm sure theres plenty Yaris in the Vegas to Socal area that will help you out. If you could since we lost information from the hack post the graphs and pics it would be appreciated. Also is there anything anybody needs to do to get in on the first 10 or is it first come first serve.
Xd intake will see production if we have sufficient interest. I have the Xd ready to do the production piece, but we need to have at least 10 Xd owners wiling to purchase it before we can justify a production run. We just don't have a feel fo rthe Xd market-though the motor is a really good one-wish I had it in my yaris.
Originally Posted by CASTREX ↑So what happened with the xD intake?
Any hopes that one will be seeing the light of day?
I knew of a few people interested but due to your long and quite absence we totally forgot about it... 🙁
Please post here if the possiblity of a group buy comes up.
Intake Mani
If you'd like to get some sort of official list generated on the site-that might be helpful.
Originally Posted by bdc87 ↑Good to see you back, I've been waiting patiently for this manifold. I live in Northern California and which I could help but, I'm sure theres plenty Yaris in the Vegas to Socal area that will help you out. If you could since we lost information from the hack post the graphs and pics it would be appreciated. Also is there anything anybody needs to do to get in on the first 10 or is it first come first serve.
anything going on for the Toaster?
PM sent 😉Originally Posted by richardholdener ↑Xd intake will see production if we have sufficient interest. I have the Xd ready to do the production piece, but we need to have at least 10 Xd owners wiling to purchase it before we can justify a production run. We just don't have a feel fo rthe Xd market-though the motor is a really good one-wish I had it in my yaris.
Is this a request for the early Xb-we can just need 10 Xb owners to step up.
Originally Posted by Black Yaris ↑anything going on for the Toaster?
Nice... I am reposting this on Scion Life!
Good to know this project is still alive! Hopefully me and my wallet will still be alive by the time this goes into production. 😆
since the stuff got deleted whats the estimated cost of this ?
Here is the dyno grap of the stock vs new intake that was removed previously.
1 attachment not included in this copy
Castrex, the xD one is also for the Yaris TS guys, yes?
13 whp increase?
I believe so and something like 25 with a full exhaust, but don't quote me on that.Originally Posted by PETERPOOP ↑13 whp increase?
If I remember correctly he hit 120whp with no cats and 2 inch back.
can this work with the 2500$ turbo kit that is coming out? or is it one or the other.
Yeap....Originally Posted by cali yaris ↑Castrex, the xD one is also for the Yaris TS guys, yes?
XD, Yaris TS, 2009 Corolla/Matrix, Auris..........
All share the new 2ZR-FE engine.
can this work with the 2500$ turbo kit that is coming out? or is it one or the otherI think he is designing them both on the same car, so assumingly so...
Does it require a different engine management? Or will it run on the stock ECU?
Subscribed.
I believe the intake manifold will run on the stock ECU. It's not forced induction, just BETTER induction 😁
And, since it's on the cold side, it would certainly work alongside a turbo application.. 🤤
And, since it's on the cold side, it would certainly work alongside a turbo application.. 🤤
I'm just a bit doubtful if the stock ECU will be able to handle the better induction without throwing a code. It seems to have quite tight operating parameters which it considers "normal".
Will an aftermarket air filter be necessary, or can you just bolt the stock airbox back in?
Lots of questions but that's because I'm interested in the product. 10whp is too good a gain to turn down if it is plug and play.
Will an aftermarket air filter be necessary, or can you just bolt the stock airbox back in?
Lots of questions but that's because I'm interested in the product. 10whp is too good a gain to turn down if it is plug and play.
If the TB remains in the same position which it think it does you should be able to use the stock airbox.... BUT,, why would you do that? In order to achive the full benefits of an Intake manifold the car will require a performance Intake and Exhaust. Other wise what would be the point to invest on the Intake Mani???Originally Posted by cleong ↑I'm just a bit doubtful if the stock ECU will be able to handle the better induction without throwing a code. It seems to have quite tight operating parameters which it considers "normal".
Will an aftermarket air filter be necessary, or can you just bolt the stock airbox back in?
Lots of questions but that's because I'm interested in the product. 10whp is too good a gain to turn down if it is plug and play.
🤤ready and waiting.just wish there was a little more in the 4-5k range.
🤷Originally Posted by ROCKLAND TOYOTA ↑since the stuff got deleted whats the estimated cost of this ?
i think something like $700,but i hope less.
That will sell very well for xD owners.......perhaps a caravan down from the NW with all of our owners would help production......LOL......
Patiently waiting for intake.....the 1.5 needs something liek this badly.
Patiently waiting for intake.....the 1.5 needs something liek this badly.
I'm just a bit doubtful if the stock ECU will be able to handle the better induction without throwing a code. It seems to have quite tight operating parameters which it considers "normal".The prototype was tested and produced the existing dyno chart. Richard has not mentioned any CEL's with the prototype intake manifold. I'm sure he will confirm this one way or another.
going supercharged. i wont be needing this anymore. still hope all works ouyt well though
I just don't see any reason for the intake to be more than a few hundred dollars. Any of my V8's from Edlebrock cost around $300 to $400, brand new. Granted these were produced on a mass scale, but, it's only a casting issue. Just my .02
don't know if I'm reading it right but the low end is really low compared to "stock."
The area under the curve for the intake manifold looks to be much lower than that of stock so wouldn't that be of less benefit or something.
Not trying to bash the manifold but I was thinking it would increase the numbers along the whole rpm range.
The area under the curve for the intake manifold looks to be much lower than that of stock so wouldn't that be of less benefit or something.
Not trying to bash the manifold but I was thinking it would increase the numbers along the whole rpm range.
Please feel free to ask questions about the intake rather than resort to speculation. The intake offers the gains described by the dyno chart with no CEL and no changes to ECU. There are no programming changes necessary for the intake upgrade. The reason for this is the Yaris motor features a mass air meter which compensates for the additional airflow produced by the resonance tuning. The mass ai rmeter will address the extra airflow and offer the necessary extra fuel flow. The intake upgrade produced the same air/fuel curve as the stock manifold. These gains are not dependant on the CAI, but the combination of the CAI and intake will offer slightly more power than the intake and stock air box.
Originally Posted by cleong ↑I'm just a bit doubtful if the stock ECU will be able to handle the better induction without throwing a code. It seems to have quite tight operating parameters which it considers "normal".
Will an aftermarket air filter be necessary, or can you just bolt the stock airbox back in?
Lots of questions but that's because I'm interested in the product. 10whp is too good a gain to turn down if it is plug and play.
You are reading the graph incorrectly. As indicated by the power curve, the new intake offers better power at every rpm than the stock manifold, from below 2500 rpm to 6500 rpm. Though the most prominent gains come past 5000 rpm, the new intake does offer gains of 4-5 lbs. ft. at 3500rpm and 5-6 lbs. ft. at 4000 rpm.
Originally Posted by baked_limabeans ↑don't know if I'm reading it right but the low end is really low compared to "stock."
The area under the curve for the intake manifold looks to be much lower than that of stock so wouldn't that be of less benefit or something.
Not trying to bash the manifold but I was thinking it would increase the numbers along the whole rpm range.
This is an economy of scale question. To produce a casting requires a substantial initail investement in tooling and molds ($30-40,000 for a simple one), then castings and machining cost are dependant on the number of articles produced (the greater the production run the lower the per unit cost). naturally we will not be casting an intake for the Yaris market as we doubt intake sales will justify the investment of $50,000. This means we have to run small production runs of a hand-fabricated (some CNC work) intake-the end result is a more expensive per unit cost.
Originally Posted by KCALB SIRAY ↑I just don't see any reason for the intake to be more than a few hundred dollars. Any of my V8's from Edlebrock cost around $300 to $400, brand new. Granted these were produced on a mass scale, but, it's only a casting issue. Just my .02
We will provide a test to verify the gains both turbo (and centirfugal supercharged) and NA, as the intake offers power gains on all applications. Contrary to some of the nonsense on the internet, intake design is a function of engine displacement, cam timing and operating rpm. The difference between an intake for a normally aspirated combination and a turbo combination (using the same motor, cam tming and operating speed) is minimal. Again, the intake runs with stock ECU and no CELs.
Originally Posted by cali yaris ↑I believe the intake manifold will run on the stock ECU. It's not forced induction, just BETTER induction 😁
And, since it's on the cold side, it would certainly work alongside a turbo application.. 🤤
This is not entirely accurate, as the intake will offer gains with the stock air box and exhaust. The combination of the intake, CAI and free-flowing exhaust will produce more power than the intake with a stock exhaust and air box, but the intake will still off the same percentage gains with both combinations.
Originally Posted by CASTREX ↑If the TB remains in the same position which it think it does you should be able to use the stock airbox.... BUT,, why would you do that? In order to achive the full benefits of an Intake manifold the car will require a performance Intake and Exhaust. Other wise what would be the point to invest on the Intake Mani???
Hope there is no confusion, but the intake for the 1.5L Yaris is different than for the 1.8L Xd (or Yaris TS). I hope the Yaris TS and Xd will share the same design, but I will need to check packaging on TS before we know for sure.
Originally Posted by bzinn 1 ↑That will sell very well for xD owners.......perhaps a caravan down from the NW with all of our owners would help production......LOL......
Patiently waiting for intake.....the 1.5 needs something liek this badly.
If you are running the Blitz/Greddy then the intake/supercharger combo replace the factory intake. If you are going the Rotrex route, this intake will offer sizable power gains on that application.
Originally Posted by whooppee777 ↑going supercharged. i wont be needing this anymore. still hope all works ouyt well though