Yarisworld Archive

Yaris Intake Manifold

201 posts · 92,195 views · page 3 of 5

Replies continued

TamagoOff Grid · Oct 28, 2008#101
Originally Posted by richardholdener ↑
Unfortunately we lost a rod while running higher boost levels and .
what kind of boost levels were you running and for how long? help the 1NZ community out
richardholdenerThread starterLas vegas, NV · Oct 31, 2008#102
I am helping the community out by findin gout exactly what caused the probelm before jumping on the speculation bandwagon. The boost level did not hurt the motor nor the length of time spent at any given boost level. There had to be some type of ignition error that that resulted in excessive timing. We are looking into this and will report if we find the answer.

Originally Posted by Tamago ↑
what kind of boost levels were you running and for how long? help the 1NZ community out
Nexus1155Dorchester · Oct 31, 2008#103
got any pictures? Did the rod just break, bearings/melted piston?.... The H22 i have overspun the bearing and it popped a nice hole in the block...
TamagoOff Grid · Oct 31, 2008#104
Originally Posted by richardholdener ↑
I am helping the community out by findin gout exactly what caused the probelm before jumping on the speculation bandwagon. The boost level did not hurt the motor nor the length of time spent at any given boost level. There had to be some type of ignition error that that resulted in excessive timing. We are looking into this and will report if we find the answer.
ok i guess that's a non answer ;) stock 1NZ rods break on fully stock xA/B's due to high RPM's for extended periods of time. toyota fixed this by giving you Yaris people taller gears (better highway cruising) ..

if you read the write-up done by elprototypes on boosting the 1NZ the rods are the first things to go. the engine is over-square and offset crank which causes piston slap (which is obviously made worse by boost) and ultimately rod failure. there is no "speculation bandwagon" on the 1NZ.. it's been around almost 10 years..

is this your first 1NZ vehicle, Richard?
cali yarisCanoga Park, CA · Oct 31, 2008#105
I think by speculation bandwagon, he meant he's not going to speculate about his particular car within the context of what caused the failure. It is interesting that his failed under less than extremely stressful conditions, while mine has not failed after six months of driving at 8psi without any tuning whatsoever.

So, whatever he finds out will be interesting. A pic of the rod would sure be entertaining, in the meantime.
ROCKLAND TOYOTAROCKLAND COUNTY NY · Oct 31, 2008#106
Originally Posted by Tamago ↑
ok i guess that's a non answer ;) stock 1NZ rods break on fully stock xA/B's due to high RPM's for extended periods of time. toyota fixed this by giving you Yaris people taller gears (better highway cruising) ..

if you read the write-up done by elprototypes on boosting the 1NZ the rods are the first things to go. the engine is over-square and offset crank which causes piston slap (which is obviously made worse by boost) and ultimately rod failure. there is no "speculation bandwagon" on the 1NZ.. it's been around almost 10 years..

is this your first 1NZ vehicle, Richard?
don't mind him, he's just our resident scion ass paper who thinks his knowledge is helpful.....
TamagoOff Grid · Oct 31, 2008#107
Originally Posted by ROCKLAND TOYOTA ↑
don't mind him, he's just our resident scion ass paper who thinks his knowledge is helpful.....


better than being ignorant like you
richardholdenerThread starterLas vegas, NV · Oct 31, 2008#108
Thanks Rockland for the insight on the previous post regarding con rods-it is appreciated. Piston slap, offset crank pins-where do these guys come up with this stuff? I can remember when the light clicked on for me, the day that I realized that I didn't know everything and in fact knew very little. That is the day I officially started learning. Unfortunately, people put forth much more effort convincing others of their knowledge than actually obtaining it. For the record-Rod failure is caused by tension loads (rpm), extreme compression loads (detonation or extremely high power levels) or fatigue cycle life (extended operation near fatigue). Since none of the other situations were present-we must suspect detonation as the culprit, but will perform a post mortem to see if there is any evidence. The 1NZFE rods do not fail by design, neither did the Honda rods or small block Ford rods or any of the many powdered metal production rods-the culprit has almost always been a tuning error. There is a limit to the power production with the production rods, but since (in the case of this yaris) we were nowhere near that absolute power limit

Originally Posted by ROCKLAND TOYOTA ↑
don't mind him, he's just our resident scion ass paper who thinks his knowledge is helpful.....
TamagoOff Grid · Oct 31, 2008#109
Originally Posted by richardholdener ↑
The 1NZFE rods do not fail by design
so explain this:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

on a stock engine, stock ecu, intake, exhaust, bone dry day (so dont' even say it was hydrolock) at 85mph (over 4300rpm) about 80F ambient temperature, engine had 47,000 miles on it.

the 1NZ is not designed to rev above 4000rpm for extended periods of time.
ROCKLAND TOYOTAROCKLAND COUNTY NY · Oct 31, 2008#110
Originally Posted by Tamago ↑


better than being ignorant like you
😆 ass paper.....
TamagoOff Grid · Oct 31, 2008#111
Originally Posted by ROCKLAND TOYOTA ↑
😆 ass paper.....
hey, at least i didn't put spaghetti with bendy ends between my seatbelt bolts and call it a suspension mod ;)
ROCKLAND TOYOTAROCKLAND COUNTY NY · Oct 31, 2008#112
Originally Posted by Tamago ↑
hey, at least i didn't put spaghetti with bendy ends between my seatbelt bolts and call it a suspension mod ;)
better than that video of you with the bald tires. what a waste of 5 minutes that was.....
TamagoOff Grid · Oct 31, 2008#113
Originally Posted by ROCKLAND TOYOTA ↑
better than that video of you with the bald tires. what a waste of 5 minutes that was.....
you think?

a video of a car that could rape you in its sleep, on tires 50mm wider than you'll ever be able to run, with twice the power you'll ever see is worse than spaghetti and bendy ends.. that you could build from home depot or hrpworld.com for around $12... at least it's shiney with a cool sticker on it (no offense to you Garm)
Nexus1155Dorchester · Oct 31, 2008#114
GENTLEMEN!!!! CUT THE SHIT
TamagoOff Grid · Oct 31, 2008#115
Originally Posted by Nexus1155 ↑
GENTLEMEN!!!! CUT THE SHIT
i'm done..

i came here to ask richard H a legit question

Rockland started it ;)
Nexus1155Dorchester · Oct 31, 2008#116
hahah sorry, but i had to intervene, don't want Richard taking away the manifolds
richardholdenerThread starterLas vegas, NV · Oct 31, 2008#117
No worries about the intake situation--and I respect people having and voicing their opinion(this is what makes America great). I just wish they would not be so quick to draw absolute conclusions from such small samples (the equivalent of automotive bigotry). One or even two damaged con rods does not mean all NZFE rods are bad. Honda guys thought this too, but since I ran stock B16s in endurance racing where we ran 8200 rpm for 24 hours, not to mention producing over 500 hp in turbo form, I'd say the weak con rod theory was just that. FYI-Engine testing at the OEM level includes running the motor for 24 hour periods and ranging the engine speed from peak torque to peak horsepower. This is done at 1/4 throttle, 1/2 throttle, 3/4 throttle and then at WOT to endurance test the reciprocating assembly. I personally have run my Yaris in 4th gear from Vegas to So Cal and back (mileage testing for my book) and run it flat out 114 mph for almost 9 straight miles. This combined with the hundreds of dyno tests run to the rev limiter under WOT shows me that (as has been their history) Toyota over and not underbuilds their vehicles.



Originally Posted by Nexus1155 ↑
hahah sorry, but i had to intervene, don't want Richard taking away the manifolds
SabretoothSt Cloud FL · Oct 31, 2008#118
over and not underbuilds their vehicles

Well said!
TamagoOff Grid · Oct 31, 2008#120
Originally Posted by richardholdener ↑
No worries about the intake situation--and I respect people having and voicing their opinion(this is what makes America great). I just wish they would not be so quick to draw absolute conclusions from such small samples (the equivalent of automotive bigotry). One or even two damaged con rods does not mean all NZFE rods are bad. Honda guys thought this too, but since I ran stock B16s in endurance racing where we ran 8200 rpm for 24 hours, not to mention producing over 500 hp in turbo form, I'd say the weak con rod theory was just that. FYI-Engine testing at the OEM level includes running the motor for 24 hour periods and ranging the engine speed from peak torque to peak horsepower. This is done at 1/4 throttle, 1/2 throttle, 3/4 throttle and then at WOT to endurance test the reciprocating assembly. I personally have run my Yaris in 4th gear from Vegas to So Cal and back (mileage testing for my book) and run it flat out 114 mph for almost 9 straight miles. This combined with the hundreds of dyno tests run to the rev limiter under WOT shows me that (as has been their history) Toyota over and not underbuilds their vehicles.
all that said, you threw a rod 🤷
i'm not bashing the 1nzfe. i love them so much i'm on number 2. 👍
Nexus1155Dorchester · Oct 31, 2008#121
is the 1nz-fe sleeved like the B18....ehhhhh!!!! ;) happy halloween
dallasCanada · Nov 1, 2008#122
With previous dyno runs with bigger intake manifolds and throttle bodys without more displaement, more cam, or forced induction a higher flowing intake will offer very little gain and may loose h.p /torque until very high rpm.
What calculations are you using for runner diameter and length.
PETERPOOPOahu · Nov 1, 2008#123
can't wait for my manifold!
cleongSingapore · Nov 1, 2008#124
Originally Posted by PETERPOOP ↑
OoOOooOOoo. I might be one of ten with the only aftermarket intake manifold for a looooooooooong time. Nice
If the manifold turns out to be that good i'm sure Richard will be making as many as he can sell! He surely needs to recoup his R&D costs somehow.

The only way I could see a great manifold not being continued is if it costs more to make than what the market is willing to pay.
cali yarisCanoga Park, CA · Nov 1, 2008#125
The only way I could see a great manifold not being continued is if it costs more to make than what the market is willing to pay.
cali yaris = "the market" 😁
RagnaCaTVillalba, Puerto Rico · Nov 1, 2008#126
Originally Posted by Tamago ↑
so explain this:
Picture not included in this copy

on a stock engine, stock ecu, intake, exhaust, bone dry day (so dont' even say it was hydrolock) at 85mph (over 4300rpm) about 80F ambient temperature, engine had 47,000 miles on it.

the 1NZ is not designed to rev above 4000rpm for extended periods of time.
Nice! looks like the same thing that happened to my cousin's 7A-FE it was the oil pump and he didn't stop the car cuase it was late in the night. Not a big issue if watch the GUAGE! Also thats 🙄 about the above 4000rpm come down to P.R. and drive in the highway towards Cayey reving hard between 3rd and 4th gear to mantain 80mph thats above 4000rpm up hill like half hour drive or around 15 miles. I got A/T and M/T they get the same punishment when I'm behind the wheel remember it's a TOYOTA.
PETERPOOPOahu · Nov 1, 2008#127
Originally Posted by cleong ↑
If the manifold turns out to be that good i'm sure Richard will be making as many as he can sell! He surely needs to recoup his R&D costs somehow.

The only way I could see a great manifold not being continued is if it costs more to make than what the market is willing to pay.
well...

Originally Posted by richardholdener ↑
If we don't get 10 people to sign up-there will be no intakes. If we do, the those people will get the first production run of intakes and it is undecided if there will be an additional production run. Best bet if you want an intake-step up and get on the list.
richardholdenerThread starterLas vegas, NV · Nov 1, 2008#128
Is this question directed at me? The statement that a higher flowing intake will yield very little gain and may loose hp until high rpm is inaccurate. Intake manifolds are not simple flow devices-they are tuned to produce power at specific engine speeds based on the other variables you mentioned (displacement, cam timing etc...) It does not take a bigger or higher flowing intake to make more power, it takes the right design elements. The calculations are extremely complicated for more reasons than I can go into in such a short space. We ran over 100 different combinations before deciding on this one illustrated by the dyno curve provided. Intake design is more than just welding together a plenum, runners and flange.

Originally Posted by dallas ↑
With previous dyno runs with bigger intake manifolds and throttle bodys without more displaement, more cam, or forced induction a higher flowing intake will offer very little gain and may loose h.p /torque until very high rpm.
What calculations are you using for runner diameter and length.
richardholdenerThread starterLas vegas, NV · Nov 1, 2008#129
PS-The tuning effect works the same on NA and FI applications.

Originally Posted by dallas ↑
With previous dyno runs with bigger intake manifolds and throttle bodys without more displaement, more cam, or forced induction a higher flowing intake will offer very little gain and may loose h.p /torque until very high rpm.
What calculations are you using for runner diameter and length.
Nexus1155Dorchester · Nov 1, 2008#130
Intake design is more than just welding together a plenum, runners and flange
It's physics....muahahahahahah....
cleongSingapore · Nov 1, 2008#131
Originally Posted by PETERPOOP ↑
well...
Originally Posted by richardholdener
If we don't get 10 people to sign up-there will be no intakes. If we do, the those people will get the first production run of intakes and it is undecided if there will be an additional production run. Best bet if you want an intake-step up and get on the list.
Well if its a great manifold and profitable, why would Richard stop at just one (short) production run?
SabretoothSt Cloud FL · Nov 1, 2008#132
Well if the production models are well built and sell enough, what says that Garm wouldnt stock them and sell them directly? at a possible discount.
PETERPOOPOahu · Nov 1, 2008#133
well...

Originally Posted by richardholdener ↑
If we don't get 10 people to sign up-there will be no intakes. If we do, the those people will get the first production run of intakes and it is undecided if there will be an additional production run. Best bet if you want an intake-step up and get on the list.
SabretoothSt Cloud FL · Nov 1, 2008#134
Well then, get signed up...lol
bobobitchAmarillo TX · Nov 16, 2008#135
how much do intake manifolds usually go for for the yaris??? becuase i talked to some of the people from weapon r and they are developing one for the yaris and so far their headers and intakes are pretty bad ass
Nexus1155Dorchester · Nov 16, 2008#136
Weapon R is not Richard Holdener ;)
PETERPOOPOahu · Nov 16, 2008#137
everyone knows weapon r sucks
TKOPhoenix · Nov 16, 2008#138
Say...Do you have anything for the xA/xB yet?
kimoEgypt · Jan 13, 2009#139
I think 1.3L and 1.5L are the same, only diffrent in piston size between them.
Maybe be better ask the dealer.

QUOTE=ZING;157953]😢[/QUOTE]
newyarSoCal · Mar 21, 2009#140
Did these ever get produced? Any results, feedback from the first 10 customers?
eTiMaGoBangkok, Thailand · Mar 21, 2009#141
nope, it's all been silent for the past couple months, some people still holding on to a glimmer of hope...
cali yarisCanoga Park, CA · Mar 21, 2009#142
I'm gonna make my own.
bdc87Lake County, CA · Mar 21, 2009#143
For others 2?
blacksandiegovitzJust chillin' out brah ! · Mar 21, 2009#144
Originally Posted by cali yaris ↑
I'm gonna make my own.
WOOt Woot , have a few made for other Yw members too 👍
AlexNet0Rockland, ME · Mar 21, 2009#145
Originally Posted by cali yaris ↑
I'm gonna make my own.

me, me, me, me tooo, lol let us know what it costs when its done so I can start saving!
cleongSingapore · Mar 23, 2009#146
Could someone just talk Mr. Holdener into selling the design?
marcustoronto, canada · Mar 23, 2009#147
i think hes busy with more profitable mods.
eTiMaGoBangkok, Thailand · Mar 23, 2009#148
yes but I agree with cleong, if Richard was willing to sell the design, someone else could arrange for its production and distribution. Would save a lot of time compared to re-engineering a new design...
yaris-meAnaheim, CA · Mar 23, 2009#149
Cali Yaris?🙂
Nexus1155Dorchester · Mar 26, 2009#150
Has anyone tried prospecting him to sell the design yet?