so rotrex is making a sc?
Yaris Intake Manifold
201 posts · 92,195 views · page 2 of 5
Replies continued
Sorry I meant 1.8......the xD really us under powered for what it weighs.....that is the only complaint about the xD you will hear from owners.Originally Posted by richardholdener ↑Hope there is no confusion, but the intake for the 1.5L Yaris is different than for the 1.8L Xd (or Yaris TS). I hope the Yaris TS and Xd will share the same design, but I will need to check packaging on TS before we know for sure.
"The Rotrex route"... ? need more info!
Everyones ears just perked up and did a Scooby, lol
I am not providing any new information-I just thought the PE blower kit used a Rotrex. The point is that a centrifugal supercharger systems still uses the stock or my intake and that this blow-thru system will benefit from the intake upgrade.
Originally Posted by cali yaris ↑"The Rotrex route"... ? need more info!
You can't use the blitz with this IM as it (the Blitz kit) replace the intake and manifold. It seems to me that if this with a full exhaust is making 120whp, so say maybe 125 with the pulley set...why exactly would you spend the $3400 on the blitz, when that only make 130ish? 700-intake-200 good CAI 700ish for full exhaust 250? for pullies....1850 compared to 3400.....plus no warranty issues....plus the ability to use a "rotrex style" SC eventually or turbo? seems a simple choice to me
The retail listed has alwasy been $699. We applied a numberof bolt ons to the Yaris and came up with 120 wheel hp-130-135 would be difficult without going inside the motor to port the head and add cams. I believe the blitz supercharger has its own intake as part of the blower so I don't think it can be combined with the intake. Running a turbo or centrifugal supercharger with the intake at 4-5 psi should be good for around 150 hp.
Originally Posted by bdc87 ↑$699 is better then before I believe it was going to be $800. And look the Intake and all other boltons should give around 130-135hp. Or add the Blitz to this and it's looking like 145-150hp.
sweet. Looking at it again, i realized that i was looking at it wrong. I'm an idiot. I wonder if i'll change classes in autox if i get this...
EDIT: been reading the solo rules and it will change my classing.
EDIT: been reading the solo rules and it will change my classing.
I'm running a supercharge tune on a N/A car, so yea. Don't jump to conclusions.Originally Posted by cleong ↑I'm just a bit doubtful if the stock ECU will be able to handle the better induction without throwing a code. It seems to have quite tight operating parameters which it considers "normal".
Will an aftermarket air filter be necessary, or can you just bolt the stock airbox back in?
Lots of questions but that's because I'm interested in the product. 10whp is too good a gain to turn down if it is plug and play.
BTW, Mr. Richard Holdner, is this kit the top end one? Or is this the midrange one? I know there was a poll earlier. I didn't get to see what everyone had chosen.
Thi sis the top end version-we willnot be offering the mid-range version.
Originally Posted by ddongbap ↑I'm running a supercharge tune on a N/A car, so yea. Don't jump to conclusions.
BTW, Mr. Richard Holdner, is this kit the top end one? Or is this the midrange one? I know there was a poll earlier. I didn't get to see what everyone had chosen.
NICE.Originally Posted by richardholdener ↑Thi sis the top end version-we willnot be offering the mid-range version.
Thank you. You told me exactly what I wanted to know. As you can see, I'm rather far away, so when the user dyno charts start flooding in confirming the performance increase, I'm buying one.Originally Posted by richardholdener ↑Please feel free to ask questions about the intake rather than resort to speculation. The intake offers the gains described by the dyno chart with no CEL and no changes to ECU. There are no programming changes necessary for the intake upgrade. The reason for this is the Yaris motor features a mass air meter which compensates for the additional airflow produced by the resonance tuning. The mass ai rmeter will address the extra airflow and offer the necessary extra fuel flow. The intake upgrade produced the same air/fuel curve as the stock manifold. These gains are not dependant on the CAI, but the combination of the CAI and intake will offer slightly more power than the intake and stock air box.
As you mention that it is a CNC-ed part, do you have problems with heatsoak from having it bolted to the engine, and then the manifold heating up the intake air temperature though? One of my mates tried a custom built stainless steel manifold on his engine, but abandoned the idea as intake temps jumped from an ambient of 100-110 degrees to 160 degrees, which ended up costing the engine power instead.
^^^you need aluminium not stainless steel for an intake.^^^^
lol not trying to bash, but youre funny as hell dude, what constitutes it need to be made of aluminum... if someone has a sheet of stainless steel and welded up an intake manifold would it not work? right... i mean hell, even if the thing was made of fiberglass it could essentially work....
fiberglass would be ok but we already have plastic one unless the could mold a nice one out of carbon fiber. about the aluminium i would have thought that it would dissapate heat better than stainless.Originally Posted by Nexus1155 ↑lol not trying to bash, but youre funny as hell dude, what constitutes it need to be made of aluminum... if someone has a sheet of stainless steel and welded up an intake manifold would it not work? right... i mean hell, even if the thing was made of fiberglass it could essentially work....
i think its like a 50/50 thing because of brake lines and exhausts and junk are made from stainless steel, but i think any metal would work... as long as it doesnt melt
subscribed and waiting
+1Originally Posted by ROCKLAND TOYOTA ↑damm east coast misses out AGAIN......
We need pics and price? pls.
As indicated elsewhere in this post, the retail pricing is $699. No pics are available since all we have is the performance prototype which does not represent the production intake. What we need at this point is to generate an official list. We need to have 10 yaris owners step up to purchase the intake so they can go into production. There will be NO deposit money required up front, just your word in print that you will be purchasing the intake when the production pieces are ready. Prior to any payment and shipping the production intakes, I will be happy to have Garm (or other member) come out for an official dyno test to illustrate the gains. For this intake to be produced, we need to have 10 buyers. If we get 20 buyers, we can talk about a group buy which would knock off $50 per manifold.
I would just like to throw my 2 cents into this. I take my hat off to the making of this intake manifold. I really don't see committing to a high dollar item without seeing more info on this intake manifold. Everyone has to realize you are committing "with your word and in print" to purchase a item that hasn't even been seen yet. I wouldn't commit to buy any performance item without seeing pictures. whats wrong with posting prototype pictures? Its prototype right? I think everyone here would like to see pictures, and have more info on what they are committing to this.
Any A/F readings taken?
Any A/F readings taken?
im sure there are 20 people right now who want one one. if we had 40 people whats the discount then???Originally Posted by richardholdener ↑As indicated elsewhere in this post, the retail pricing is $699. No pics are available since all we have is the performance prototype which does not represent the production intake. What we need at this point is to generate an official list. We need to have 10 yaris owners step up to purchase the intake so they can go into production. There will be NO deposit money required up front, just your word in print that you will be purchasing the intake when the production pieces are ready. Prior to any payment and shipping the production intakes, I will be happy to have Garm (or other member) come out for an official dyno test to illustrate the gains. For this intake to be produced, we need to have 10 buyers. If we get 20 buyers, we can talk about a group buy which would knock off $50 per manifold.
I know of Richard from my mustang days, you can believe what he says but, pics of the actual product might help sway some thinking about it.
Since we don't even have 10 people willing to put their name on a list as of yet-I think it is a little premature to talk about group buys for 40. Also, the photo issue has already been addressed-only a prototype exists and it does not represent the production piece. Here is a photo of the production Nissan Versa intake-the yaris intake will feature a head flange, runners and a common plenum with a throttle body mount,but it will look nothin glike this one nor will it look like the prototype used for testing. There will be no photos of the prototype intake-only if and when the production piece is ready to display (much earlier than the full production run if we get the requistite number of yaris owner to indicate they intend to purchase if and only if we provide the following things: 1. an intake that bolts on a provides the power gains illustrated by the power graph, accepts the stock throtle body and associated lines and fittings and runs with no CELs at a price of $699). Since I am asking for no money up front, only an indication to purchase if these requirements are met. Please let me know if there is sufficient interest or if we should move on to a different application..
Originally Posted by ROCKLAND TOYOTA ↑im sure there are 20 people right now who want one one. if we had 40 people whats the discount then???
Nissan Versa intake photo too large to upload-can I e-mail it to someone to manipulate?
Air fuel is the same as stock intake since this motor has a mass air meter.
Originally Posted by cee_dub2003 ↑I would just like to throw my 2 cents into this. I take my hat off to the making of this intake manifold. I really don't see committing to a high dollar item without seeing more info on this intake manifold. Everyone has to realize you are committing "with your word and in print" to purchase a item that hasn't even been seen yet. I wouldn't commit to buy any performance item without seeing pictures. whats wrong with posting prototype pictures? Its prototype right? I think everyone here would like to see pictures, and have more info on what they are committing to this.
Any A/F readings taken?
upload to a image hosting site and usually during the upload they have resize options. imageshack.us or tinypic.com are a few
People on this forums buy F/I kits that produce similar power and spend tons more.Originally Posted by cee_dub2003 ↑I would just like to throw my 2 cents into this. I take my hat off to the making of this intake manifold. I really don't see committing to a high dollar item without seeing more info on this intake manifold. Everyone has to realize you are committing "with your word and in print" to purchase a item that hasn't even been seen yet. I wouldn't commit to buy any performance item without seeing pictures. whats wrong with posting prototype pictures? Its prototype right? I think everyone here would like to see pictures, and have more info on what they are committing to this.
Any A/F readings taken?
Just because you don't believe the words of this master, doesn't make it false.
He probably doesn't post a picture, because like just about everyone else in this world, if he posts the prototype picture, everyone'll expect that. Or have some kind of misguided opinion of the product. When the final one arrives, and isn't what people expected, even though that isn't what was even promised, people'll complain. Its what happens.
And because you think that you need pictures, doesn't mean the rest of us do. Don't speak for the rest of us.
this is the versa manifold.
1 attachment not included in this copy
i saw that in the siphon magazing... anyone know what happened to them, they just stopped publishing?!
no more siphon magazine this issue was the last.i am just guessing the same company is producing the yaris manifold.
put me on that list.
you are on the list.Originally Posted by PETERPOOP ↑put me on that list.
If the prototype doesn't look like the functional production piece, would it still work the same and put out similar dyno numbers?
Showing us a Nissan Versa manifold doesn't do much for me; it has less in common to an actual production Yaris manifold than a prototype Yaris manifold.
Showing us a Nissan Versa manifold doesn't do much for me; it has less in common to an actual production Yaris manifold than a prototype Yaris manifold.
Put me down on that GB list! Just need time to reserve the money
Question,Originally Posted by richardholdener ↑Is this a request for the early Xb-we can just need 10 Xb owners to step up.
Any chance the Yaris intake will fit the Xb? since you're asking for 10 owners I assume you don't think it will. Because of the throttle or because of the engine bay room ?
Thanks.
The gains would be similar for the easrly Xb since they share the same motor. We could do a run of intakes fo rthe early Xb as well (since much would be shared with yaris design), but like the yaris, we would need 10 early Xb owners to sign up to justify the production run.
Originally Posted by Noisetube ↑Question,
Any chance the Yaris intake will fit the Xb? since you're asking for 10 owners I assume you don't think it will. Because of the throttle or because of the engine bay room ?
Thanks.
Might also be able to do an adapter plate to go from yaris TB mounting flange to early XB mounting fplange-depends on orientationof intake in engine bay-I need to look at early Xb engine bay.
if i put on myself on the list is there a time limit for the pay or can i be asure that if i dont put myself on the list now would it be production of the intake manifold on the future?
I'm not sure if I understand the question. If you are serious about wanting to purchase an intake for the yaris-put your name on the list. If we don't get 10 people to sign up-there will be no intakes. If we do, the those people will get the first production run of intakes and it is undecided if there will be an additional production run. Best bet if you want an intake-step up and get on the list.
OoOOooOOoo. I might be one of ten with the only aftermarket intake manifold for a looooooooooong time. Nice
I would be interested in an intake that had a flange for a larger throttle body. Anyone who has installed an intake on our cars sees how tiny the throttle body is on our motors. I think If we were to swap to a larger throttle body off like a TC or a corolla then there would be a much more noticible difference in HP 🤷
I thought there was a plate for that?
The prototype intake was made with a flange to accept the larger Xd throttle body. The throttle body upgrade was only worth 1-2 hp-not enough to justify the expense of purchasing the new or used throttle body. Since I know whatthe next question will be (we've already covered this), the larger Xd throttle body will bolt onto the stock intake but sealing will be an isue since the hole in th eintake is much smaller than the hole in the throtle body. Ditton fo rthe rubber o-ring throttle body gasket. Besides, you will need to enlarge hole in th eintake which will be difficult since there is little wall thickness. An adapter plate can be made to facilitate the swap, but again cost versus power gain is not very favorable.
Originally Posted by PHXDEMON ↑I would be interested in an intake that had a flange for a larger throttle body. Anyone who has installed an intake on our cars sees how tiny the throttle body is on our motors. I think If we were to swap to a larger throttle body off like a TC or a corolla then there would be a much more noticible difference in HP 🤷
Originally Posted by richardholdener ↑Air fuel is the same as stock intake since this motor has a mass air meter.
That is really hard to understand! For one the MAF only calibrates air volume and AIT temp. adding more air into each cylinder would cause the car to run lean, and ping, causing the knock sensor to draw back timing to compensate for the lean in tunr loosing HP.
I have seen a intake manifold for a TC do this. I would really like to see how you have done this when the Toyotas MAF is a very learing piece of equipment.
Hopefully this will help you and others understand why your comments are somewhat inaccurate. The mass air meter is not a learning device, it is a simple measurement device that measures mass flow (temp, volume and infered density). The learning portion of the equation comes from the ECU (interpretation of signals from various sensors including MAF). Using a hot wire, voltage is applied to keep the wire at a given temperature. The greater the airflow (or lower the temperature of said air), the greater the voltage required to maintain a constant element temperature. This change in voltage (or frequency on some MAF applications) is correlated to airflow based on the relationship between ID of the meter assembly and what is refered to as the sample tube (flow orifice to hot wire element). The change in airflow through the system (that happens at different engine speeds and/or loads) is compensated for by the MAF. The same thing happens with changes in airflow from something like an intake upgrade. Problems can arise when you run out of effective meter range (we call this topping out the meter-meaning we reach the voltage ceiling near 5.0V). This can happen with major power gains like those achieved with a blower or turbo. We rescale the meter and combine it with larger injectors for these applications, but for something simple like an intake upgrade-there is no need for this. In reality, altering the mass air meter (by orientation, entry or alteration of ratio between flow orifice and metering orifice) will have much more of a change in the air/fuel ratio than adding the intake manifold. This knowledge on the workings of a mass air meter plus the actual data that came from the hundreds of direct back-to-back dyno tests run indicate that the air/fuel is not effected by the change in intake manifold on the Yaris. I make it a point never to bring speculation to a data fight.
Originally Posted by cee_dub2003 ↑That is really hard to understand! For one the MAF only calibrates air volume and AIT temp. adding more air into each cylinder would cause the car to run lean, and ping, causing the knock sensor to draw back timing to compensate for the lean in tunr loosing HP.
I have seen a intake manifold for a TC do this. I would really like to see how you have done this when the Toyotas MAF is a very learing piece of equipment.
Thank you for clarifying that better for me. Sorry for the somewhat information information.
ANd this would work on my '09 LB 1.3L engine, yes?
Intake has only been tested on 1.5L. NOt sure if 1.3L shares same intake config.
Originally Posted by richardholdener ↑Intake has only been tested on 1.5L. NOt sure if 1.3L shares same intake config.
😢