how about for turbo? is anyone going 2.5 or 3"?
The custom/aftermarket exhaust thread! [Pics + Videos]
225 posts · 840,944 views · page 3 of 5
Replies continued
depends on the amount of boost your planning on running if a lower boost set up then 2.25 or 2.50 so you can maintane your torque. If you looking for ultimate power and monster boost 30psi ect I would go for 3. Thats just me and from what I have seen at the track hereOriginally Posted by RacerFreakXXX ↑how about for turbo? is anyone going 2.5 or 3"?
Do those wide tips like the Nitto and the Greddy fit under the stock lip alright? If I recall, there was a member that ended up with part of his bumper melted.
Here's mine, 2 inch resignator back, center tip, loved the tone of my megan exhaust I had then recycle it...
Total cost, $270
$140 used exhaust purchased 2 yrs ago
$100 mandrel bent 2 inch piping
$30 twin exhaust tip via ebay.
http://www.youtube.com/watch?v=kU6Df...=youtube_gdata
Total cost, $270
$140 used exhaust purchased 2 yrs ago
$100 mandrel bent 2 inch piping
$30 twin exhaust tip via ebay.
http://www.youtube.com/watch?v=kU6Df...=youtube_gdata
Nice, another center-exit!Originally Posted by Sabretooth ↑Here's mine, 2 inch resignator back, center tip, loved the tone of my megan exhaust I had then recycle it...
Total cost, $270
$140 used exhaust purchased 2 yrs ago
$100 mandrel bent 2 inch piping
$30 twin exhaust tip via ebay.
http://www.youtube.com/watch?v=kU6Df...=youtube_gdata
how about for turbo? is anyone going 2.5 or 3"?Mine is 2.5". Can't imagine needing 3" on the 1NZ
OK, adding mine to the mix! Custom center exit with rectangular chrome tips. Used an Imco muffler and an Imco resonator. Both cylindrical in shape and they tuck up nice underneath with nothing hanging down. Major props go to All Muffler Service (Mark and Bill) in Rocklin, CA. These guys are a couple of gear heads and they both had fun working on my car. Highly recommend this shop if you want a custom exhaust. 👍
All stock, prior to surgery:
Picture not included in this copy
Out with the old:
Picture not included in this copy
Old stuff: muffler, resonator and the rear jack point:
Picture not included in this copy
New stuff! Obviously still on the lift. Just painted the resonator, pipe and some of the pan underneath the spare tire:
Picture not included in this copy
A down low view:
Picture not included in this copy
Up high, looking down. Just enough tip showing in my opinion:
Picture not included in this copy
Everything tucked up nice and tight and blacked out:
Picture not included in this copy
Pic from a little further away:
Picture not included in this copy
And that's it! Hope you like. 😁
All stock, prior to surgery:
Picture not included in this copy
Out with the old:
Picture not included in this copy
Old stuff: muffler, resonator and the rear jack point:
Picture not included in this copy
New stuff! Obviously still on the lift. Just painted the resonator, pipe and some of the pan underneath the spare tire:
Picture not included in this copy
A down low view:
Picture not included in this copy
Up high, looking down. Just enough tip showing in my opinion:
Picture not included in this copy
Everything tucked up nice and tight and blacked out:
Picture not included in this copy
Pic from a little further away:
Picture not included in this copy
And that's it! Hope you like. 😁
we've got two in NorCal, can't wait to see it at the upcoming meet!
Thanks! I'll be there. 👍
Installed a Tanabe Concept G yesterday. Its really nice to actually hear my exhaust. Im sure the honda guys in the 'hood like it but Ive definitely pigeonholed myself with this mod (um ricer maybe?). Im cool with that. I think it sounds great.
2 attachments not included in this copy
Hey everyone this is my first post so bear with me, I've been lurking for a couple months and I just installed an afe intake and the trd sway bar. What does everyone think of the usdm trd exhaust? I can get it for around 200 new so I wanted to know if it's good quality and sound. Thanks.
😈
1 attachment not included in this copy
Originally Posted by Herbicidal ↑OK, adding mine to the mix! Custom center exit with rectangular chrome tips. Used an Imco muffler and an Imco resonator. Both cylindrical in shape and they tuck up nice underneath with nothing hanging down. Major props go to All Muffler Service (Mark and Bill) in Rocklin, CA. These guys are a couple of gear heads and they both had fun working on my car. Highly recommend this shop if you want a custom exhaust. 👍
And that's it! Hope you like. 😁
Looks really nice and it appears a lot of thought went into the design. Would be great to hear it? Also, how about those tips?
Thankks got it customized for the sedan- http://www.youtube.com/watch?v=yTuYUDUCj7w is the vid for itOriginally Posted by changchewsoon ↑that is a nice and sexy exhaust :)
Thanks for the compliment! Hmmm. I haven't tried to do a video with sound, maybe I'll try to figure that out. The tips were custom done by that shop, just waiting for someone to buy them. As it turns out that would be me! 😁Originally Posted by fnkngrv ↑Looks really nice and it appears a lot of thought went into the design. Would be great to hear it? Also, how about those tips?
HK exhaust on my 2009 Sedan
Video - http://www.youtube.com/watch?v=hKkwIF19TYo
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
EDIT: Not sure why the pics are so small...stupid Picasa I guess.
Video - http://www.youtube.com/watch?v=hKkwIF19TYo
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
EDIT: Not sure why the pics are so small...stupid Picasa I guess.
Anyone know about any cheap like 200-300 ones I would like to purchase one, then itll prob be like 100 to get it installed.
thanks
thanks
Love the way some of those look 🤘
Can one of these be found in USA? I definetely want more audible volume, not enough to piss off the town, just enough to hear rpm's better. Also light weight, not towards the back towards the front towards the back like the stock unit.
Thunder seems to fit this description, but I can't find one for sale.
rock on
Thunder seems to fit this description, but I can't find one for sale.
rock on
Im just wondering what measurement of muffler would fit a stock 1.3L Yaris ? HAtchback 2009 version =)
JDM Blitz NUR Spec S Axle Back Exhaust.
file://localhost/var/mobile/Media/DCIM/100APPLE/IMG_0206.MOV
file://localhost/var/mobile/Media/DCIM/100APPLE/IMG_0206.MOV
Anyone know about any cheap like 200-300 ones I would like to purchase one, then itll prob be like 100 to get it installed.You should be able to bolt on an exhaust yourself.
Sedan axle-backs:
HK1:
http://shop.microimageonline.com/HK-...-HK1-sedan.htm
Nitto:
http://shop.microimageonline.com/Nit...Nitto-SE-1.htm
My yaris sedan 09 with Trd Exhaust with cat/res delete.
http://www.youtube.com/watch?v=oR6sgzXNkuM
http://www.youtube.com/watch?v=oR6sgzXNkuM
got this hk1 from jumpman the noise issue is okay with me for now im gonna keep it on for a while ill get used to it. hearing music is sometimes an issue but its okay it sounds great not to ricey at least i dont think so
ill have a vid soon i guess better pics to ahha
ill have a vid soon i guess better pics to ahha
2 attachments not included in this copy
this is the car now hk1 exhaust afe intake
http://www.youtube.com/watch?v=Ge-H-l1Geq8
http://www.youtube.com/watch?v=qQe76Qu-68U
http://www.youtube.com/watch?v=Ge-H-l1Geq8
http://www.youtube.com/watch?v=qQe76Qu-68U
Cali,
Was looking at your Nitto cat back. That'll fit my 2011 3dr hatch right? Any help is greatly appreciated. Thanks bro.
Was looking at your Nitto cat back. That'll fit my 2011 3dr hatch right? Any help is greatly appreciated. Thanks bro.
I love the sound of Blitz supercharger, Thats is on my buy list for sure...
Just installed it today. Nice deep Sound. Keeping the Silencer in for now. I felt the power increase right away.
1 attachment not included in this copy
hey pops do you still have your stock axle back? if so are you willing to part with it? im on li only reason why im asking ive been looking for one
do you have any video of your set up now with the silencer ?
do you have any video of your set up now with the silencer ?
Hey guys, finally got around to getting some video of my Tanabe Medallion Touring Exhaust. It's everything I expected, sounds great, is not too loud, and everyone loves it.
http://www.youtube.com/watch?v=ROeri4U66ic
http://www.youtube.com/watch?v=N-kKwwjjmC8
I have the stock exhaust if anyone needs it.
http://www.youtube.com/watch?v=ROeri4U66ic
http://www.youtube.com/watch?v=N-kKwwjjmC8
I have the stock exhaust if anyone needs it.
I'm down with the Tanabe Medalion Touring axle back too! Sounds SWEEEEEET (sorry, no video). It's got a nice, deep bass tone, definitely not too loud, and the immediate power increase was phenomenal! Took 10 minutes to install it...just jacked up the right rear corner and pulled the wheel. Easy peasy!
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
I heared it already, my friend has one yes very nice sound, I would had one too if i had the money! ;)
What exhaust is this?? Its not the HK1, because I have an HK1 and it does not have a silencer..Originally Posted by PopsCar ↑Just installed it today. Nice deep Sound. Keeping the Silencer in for now. I felt the power increase right away.
I want to do an exhaust mod to my yaris in the future but Im still pretty new to the tuning scene I want to do a dual exhaust system with double exhaust tips on each. right now I only have a single exhaust I was wondering if its possible at all to split a stock single into a dual.
for the duel exhaust, I'd like to make a suggestion. We did this with my roomies crx. We used a camero muffler like this one:
http://www.ebay.com/itm/WALKER-EXHAU...sories&vxp=mtr
and we had it custom made to the stock axle back and had them weld extra hangers and you can put any type of duel tip on each end if you wanted.
like this:
http://www.ebay.com/itm/WALKER-EXHAU...sories&vxp=mtr
and we had it custom made to the stock axle back and had them weld extra hangers and you can put any type of duel tip on each end if you wanted.
like this:
1 attachment not included in this copy
see where the exhaust shrinks down to 1.75" after the resonator? if you're going custom, do yourself a favour and replace the exhaust back to there....you won't be disappointed (or buy my midpipe piece i had built from my part-out thread)Originally Posted by ilikerice ↑for the duel exhaust, I'd like to make a suggestion. We did this with my roomies crx. We used a camero muffler like this one:
http://www.ebay.com/itm/WALKER-EXHAU...sories&vxp=mtr
and we had it custom made to the stock axle back and had them weld extra hangers and you can put any type of duel tip on each end if you wanted.
like this:
makes a very valid point. I keep forgetting that for some reason.. I havent done that yet because I need to keep the Cat on for my class.. ONE day I will drop it off at a exhaust shop and have them weld a pipe in from Cat to axle.
here's mine
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Video;
http://www.youtube.com/watch?v=QPNziKtxzvU
i don't have a picture of it online, but i've since added a branch style resonator to it to pretty much eliminate my interior drone between 1600-2300rpm
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Video;
http://www.youtube.com/watch?v=QPNziKtxzvU
i don't have a picture of it online, but i've since added a branch style resonator to it to pretty much eliminate my interior drone between 1600-2300rpm
Fujitsubo Wagolis for Vitz RS :) had it for more than a year and loving every minute! Cleanest welds I've ever seen.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Thank for the suggestions I tried to take it in to an exhaust shop and he said all he could really do was change the tip? he said that the yaris' exhaust system itself was hard to work with or somethin
Really? They cut mine off from the cat back and installed a new resonator and muffler. I now have a center exhaust. A competent muffler shop should be able to route it up to your roof if you want. 😁Originally Posted by Dadams ↑Thank for the suggestions I tried to take it in to an exhaust shop and he said all he could really do was change the tip? he said that the yaris' exhaust system itself was hard to work with or somethin
Stock:
Picture not included in this copy
Surgery:
Picture not included in this copy
Out with the old:
Picture not included in this copy
In with the new:
Picture not included in this copy
All done:
Picture not included in this copy
This is what you want my yaris install a new exhaust (designed by myself)Originally Posted by Dadams ↑Thank for the suggestions I tried to take it in to an exhaust shop and he said all he could really do was change the tip? he said that the yaris' exhaust system itself was hard to work with or somethin
There is another one similar by a member, in PR I think, but I can't find it. It is not difficult to fabricate. All these guys are really doing is branching off of the existing tailpipe with a second one. Run the new one over to the left and weld on some tips.
keep the stock cat and res, theyre 2" thruOriginally Posted by ilikerice ↑makes a very valid point. I keep forgetting that for some reason.. I havent done that yet because I need to keep the Cat on for my class.. ONE day I will drop it off at a exhaust shop and have them weld a pipe in from Cat to axle.
just cut off the rear which is 1.75" and get something fatter
or this: (see red line for exhaust path)
Picture not included in this copy
thanks.. i was gonna drop the res. but if it is 2" anyways, why not keep it..Originally Posted by thebarber ↑keep the stock cat and res, theyre 2" thru
just cut off the rear which is 1.75" and get something fatter
or this: (see red line for exhaust path)
Picture not included in this copy
and according to your diagram.. you want me to put a side exhaust? 😉
Dadams Thank for the suggestions I tried to take it in to an exhaust shop and he said all he could really do was change the tip? he said that the yaris' exhaust system itself was hard to work with or somethinId shop around.. Obviously that shop doesn't like custom work nor wants to make a profit.. Somebody will man up and do it. Find another muffler shop
Yeah this is excactly what I want!! 😳
my yaris install a new exhaust (designed by myself)
And yeah I think Im just gunna have to go deeper into houston I figured it couldnt be that hard to do. anybody know how much a setup like this would cost?
my yaris install a new exhaust (designed by myself)
And yeah I think Im just gunna have to go deeper into houston I figured it couldnt be that hard to do. anybody know how much a setup like this would cost?
How much longer will you be holding onto that mid piece? and will I be able to have someone brach it off into two like everyone else is saying? cuase thats one hell of a deal 😁Originally Posted by thebarber ↑see where the exhaust shrinks down to 1.75" after the resonator? if you're going custom, do yourself a favour and replace the exhaust back to there....you won't be disappointed (or buy my midpipe piece i had built from my part-out thread)
I need to find my magnifying glass to see those pictures 😳
Or you could try clicking on them...
well considering the stock exhaust is well matched in size & is mandrel-bent 409ss tubing...anything a typical muffler shop is going to do to it & put crap on it. aluminized steel components that will rot out, cheesy hangers that aren't matched to the factory isolator...or better still, welded on truck style hangers to the chassis that will rot that out too. then its crush-bent so it doesn't do anything for you in terms of laminar flow