With the foglights that have the adjustment mechanism that points down towards the ground, you stick a phillips screwdriver up in there and tighten to raise, and loosen to lower. I cranked mine way down to where the light patten starts right where I can see past the hood.Originally Posted by bairjo ↑Well I was trying to upload photo copies of the directions out of the Toyota shop manual on how to properly adjust the fog lights but failed due to a "missing security token" whatever that means. Anyhow, I have not seen anything on the topic of adjustment. I'm having a little difficulty dialing one in to the proper height. Anyone care to share how you did your fog light adjustment and how did it go? By the way, my light stalk was $87 + 10 shipping. That arrangement CTScott has looks real slick....much better than the switch between the seats set-up. I had my switch between the seats on my 08 and really didn't care for it.
DIY (08' USDM Liftback): ESUSE Fog Light Install v2.0
116 posts · 258,834 views · page 3 of 3
Replies continued
Thank you. That sounds a heck of a lot easier than how Toyota spells it out. I have measured out lines taped on the wall trying to hit the mark...I'll go with the CTScott plan!
bairjo - nice job on the video! 👏
I shouldn't admit this, but I installed my foglights when I replaced the horn
with one of those premium horn kits. I never ran the wires. Been too busy
or lazy to finish the job. I'd really like to have a stalk like that, but too
chicken to mess with airbag stuff, though you make it look easy. That would
probably take me all day to do, and would have to borrow some tools.
However, maybe when it's warmer, I'll get motivated. BTW, I got the
Micro Image kit...yikes, that was a few years ago now that I think of it.
Where does the time go?
Thanks again for the video and to 🙇 CTScott for all his expertise on the Yaris!
I shouldn't admit this, but I installed my foglights when I replaced the horn
with one of those premium horn kits. I never ran the wires. Been too busy
or lazy to finish the job. I'd really like to have a stalk like that, but too
chicken to mess with airbag stuff, though you make it look easy. That would
probably take me all day to do, and would have to borrow some tools.
However, maybe when it's warmer, I'll get motivated. BTW, I got the
Micro Image kit...yikes, that was a few years ago now that I think of it.
Where does the time go?
Thanks again for the video and to 🙇 CTScott for all his expertise on the Yaris!
ok now mi problem is that I have the same kit, but I have a yaris 2013 and I don't want to cut any cable because the warranty, what can I do, don't know anything where to plug the wires o the 15 fuse go please help
Regarding cutting cables and warranty. Go ahead and cut...I asked the dealer about this when I had my 08...they said it will not void anything unless what you do damages something. For example, if you took your car to a pro to have a remote start installed....snip snip. No issues with the warranty. Just be sure you do your homework and follow the advise of the folks on here that tell you how to do it right. You will be fine...
Originally Posted by docvirus25 ↑I own a Yaris, (Thailand / General Area) year 2011 model and i've installed an aftermarket fog lamp. Does anyone here knows how to get the fog lamp indicator turned on the dashboard without replacing the OEM stalk. I'm too chicken out to remove the airbag and the oem stalk as it involves removal of the steering clock spring. Does anyone here knows which wire harness or pin to tap into for supplying the 12vdc power to light up the dash fog lamp indicator? Any help would be greatly appreciated. Thanks.
it should be pins 3 and 4 for the stalk connector under the steering column cover, but if you choose the route of tapping into the cluster (as ours here who don't have the stalk switch also don't have wires 3 and 4 under the stalk connector) you should be able to supply 12V on Pin 7 of the 16-pin connector (the shorter one and the one near the driver).
You can read more here:
need help: foglight indicator - where are the wires?
If nothing works, you might want to check if there's an LED behind the fog indicator on the cluster by gently lifting that black plastic part (where the speedometer/tach is printed on)
Instrument panel light of yaris Belta Sedan (Vios) not funtion.
Some one know how to repair it.
Some one know how to repair it.
Glad to help. Mine still doesnt work despite working in a different car with stalk switch, although both ours are factory-wired, mine is using a switch. i gave up.Originally Posted by docvirus25 ↑Thanks a zillion jcboy. That's what i'm looking for. There's an LED pre installed in the indicator panel. Your suggestion worked like charm. 👍
Instrument panel light of yaris Belta Sedan (Vios) not funtion.Check the link above.
Some one know how to repair it.
can i use this switch on my 2015 yaris
Picture lost · tapatalk.imageshack.com
Picture lost · tapatalk.imageshack.com
Picture lost · tapatalk.imageshack.com
Picture lost · tapatalk.imageshack.com
So the red and white wire is coming from the aftermarket switch is this correct?
Originally Posted by docvirus25 ↑For those who are installing the aftermarket fog lamps without a factory stalk, you can apply 12vdc tapped from the aftermarket switch and plugged into the fog lamp relay hole underneath the dashboard. Connect to the hole indicated by the green arrow using a spade connector.
Hope this helps all of you out there. Cheers!
Picture lost · i1143.photobucket.com
When I was trying to install my fog lights on my 2007 hatch a long time ago, I remember CTScott saying something like how installing them this way was a bad idea because it could screw with the fuel pump or something like that. Has anyone run into any trouble?Originally Posted by docvirus25 ↑For those who are installing the aftermarket fog lamps without a factory stalk, you can apply 12vdc tapped from the aftermarket switch and plugged into the fog lamp relay hole underneath the dashboard. Connect to the hole indicated by the green arrow using a spade connector.
Hope this helps all of you out there. Cheers!
Picture lost · i1143.photobucket.com
I did get my lights working by going through the firewall, which was a pain, and connecting by this method, without connecting to the outside fuse. Something happened and then they did not work anymore and I really didn't have time to try to fix it until now.
I'm looking to start fresh and was wondering if anyone could recommend a good kit that is pretty easy to install. I don't plan on installing the stock. I also have a denso relay from my first attempt.
Honestly, one of the best kits would be the micro-image one. It's a shame the're they've closed shop. I was lucky enough to get my hands on one for my '09.
That kit had you plugging the fog lights into a connector in the engine bay fuse box, rather than running a separate wire through the firewall.
Not only that, but it would also illuminate the indicator light in the instrument cluster.
That kit had you plugging the fog lights into a connector in the engine bay fuse box, rather than running a separate wire through the firewall.
Not only that, but it would also illuminate the indicator light in the instrument cluster.
Do you remember the name of the kit so I could try and find it online.
The Micro Image kit was a custom kit of their own.Originally Posted by M4One ↑Do you remember the name of the kit so I could try and find it online.
its a shame the pics in this are SHOT...anyone got a shot of the connection point to the engine side of the firewall fuse box?...its my only missing link at this point
I'm not 100% sure what you mean but the attached might help. It's from CTScott on here.Originally Posted by sh0rtlife ↑its a shame the pics in this are SHOT...anyone got a shot of the connection point to the engine side of the firewall fuse box?...its my only missing link at this point
Late post but might help someone else.