Hi all. I'm looking for the wires that turn on the foglights symbol in the instrument panel (when lit, it's on the left of the speedometer). Where is it located and what wire is it? Thanks.
need help: foglight indicator - where are the wires?
77 posts · 63,173 views · page 1 of 2
Replies 76
Originally Posted by yarisugi ↑Hi all. I'm looking for the wires that turn on the foglights symbol in the instrument panel (when lit, it's on the left of the speedometer). Where is it located and what wire is it? Thanks.
Here you Go , these should help, i hope 👍
5 attachments not included in this copy
Or, if you're installing aftermarket fogs without the stalk switch, you can fire the indicator directly by supplying 12V to the red wire on Pin 7 of the D2 connector on the combination meter.
Picture not included in this copy
Picture not included in this copy
Hi CTScott. Where is this D2 connector located? Yes, I have aftermarket fogs without stalk switch.
1NZYaris: Do I just need to add power to PIN3 and then the indicator will light up?
1NZYaris: Do I just need to add power to PIN3 and then the indicator will light up?
no you do not need to add power to pin 3 it is already there.Originally Posted by yarisugi ↑Hi CTScott. Where is this D2 connector located? Yes, I have aftermarket fogs without stalk switch.
1NZYaris: Do I just need to add power to PIN3 and then the indicator will light up?
If you pop the combination meter assembly off, it has two connectors D1 and D2. D1 is a 24 pin connector and D2 (the one you want) is a 16 pin connector.Originally Posted by yarisugi ↑Hi CTScott. Where is this D2 connector located? Yes, I have aftermarket fogs without stalk switch.
1NZYaris: Do I just need to add power to PIN3 and then the indicator will light up?
By the way, I believe that Pin 3 on the stalk connector only works if you are using a fog light switch equipped stalk.
Hmmm. After reading the DIY ESUSE foglight install it looks like it's possible to use that stalk connector even if you don't have a stalk for fogs...? But what is pin 3 and pin 4 and how would you hook it up to the existing wires that came with the kit?
Not true at all , this is the way mine are wired, and they work great 😁Originally Posted by CTScott ↑If you pop the combination meter assembly off, it has two connectors D1 and D2. D1 is a 24 pin connector and D2 (the one you want) is a 16 pin connector.
By the way, I believe that Pin 3 on the stalk connector only works if you are using a fog light switch equipped stalk.
You installed the relay in the D46 position for that to work. The question is if his kit has the relay that installs there or if it has the external relay.Originally Posted by 1NZYaris1 ↑Not true at all , this is the way mine are wired, and they work great 😁
So, you are definitely correct that the stalk is not required, but the relay in that position, or the external relay wired through that position would be required.
The kit that I bought included an external relay, so I wired the indicator directly to the combination meter.
Here is the EWD for the fogs, which shows pin 3 and 4 on the upper left. The Fog light relay (at D46) is at the upper right. Its output feeds the fog lights and the combination meter indicator (center).
Picture not included in this copy
the diagrames above is for useing the switch supplied with the kit .
if you want to use the factory combo switch all you need is the relay
(factory , or aftermarket) to plug into factory position as per diagrames.
if you want to use the factory combo switch all you need is the relay
(factory , or aftermarket) to plug into factory position as per diagrames.
So, let's see if I understand this. If I wanted to use the factory stalk instead of the little button that goes into the console, then all I need to do is wire up the fog lights, put the wire into the fuse box in the engine bay, and then put the relay where it's supposed to go? So I wouldn't even need that extra wiring harness for the cabin? If so, that's fantastic.Originally Posted by 1NZYaris1 ↑the diagrames above is for useing the switch supplied with the kit .
if you want to use the factory combo switch all you need is the relay
(factory , or aftermarket) to plug into factory position as per diagrames.
Oh thank God. I was reading all the DIYs for the cabin wiring and I was thinking to myself, there's gotta be a way simpler method to doing this. And there is, apparently :D
How do you know I know if I have a fog light switch equipped stalk?Originally Posted by CTScott ↑By the way, I believe that Pin 3 on the stalk connector only works if you are using a fog light switch equipped stalk.
It will have a thin rotating band with the fog light symbol, besides the wide rotating end for the head and parking lights.Originally Posted by cyberfrogg ↑How do you know I know if I have a fog light switch equipped stalk?
Ah then I guess I dont have it. =/
Im having trouble with my switch. The light indicator on the switch turns is on ALL the time except when I turn on my fogs. As soon as I turn them on, the little rectangle light on the switch turns off.. Its very annoying. I plugged in the wires into pin 3 and pin 4 of the D4 connector..
Im having trouble with my switch. The light indicator on the switch turns is on ALL the time except when I turn on my fogs. As soon as I turn them on, the little rectangle light on the switch turns off.. Its very annoying. I plugged in the wires into pin 3 and pin 4 of the D4 connector..
Based on the wiring diagram, use of pins 3 and 4 requires the fog light switch equipped stalk. On a stalk without the fog switch, pins 3 to 4 should theoretically not be switched.Originally Posted by cyberfrogg ↑Ah then I guess I dont have it. =/
Im having trouble with my switch. The light indicator on the switch turns is on ALL the time except when I turn on my fogs. As soon as I turn them on, the little rectangle light on the switch turns off.. Its very annoying. I plugged in the wires into pin 3 and pin 4 of the D4 connector..
what do you mean they should theoretically not be switched? I'm sorry, I'm a noob at all this..
Could I just connect one of the wires to Pin 7 of the D2 connector on the combination meter like you said?
Could I just connect one of the wires to Pin 7 of the D2 connector on the combination meter like you said?
Pins 3 and 4 are the input / output of the fog switch, so without the switch I am not sure whether they are left to float or what (I'd go out and put a meter on there to find out for sure, but I am in the middle of packing for vacation).Originally Posted by cyberfrogg ↑what do you mean they should theoretically not be switched? I'm sorry, I'm a noob at all this..
Could I just connect one of the wires to Pin 7 of the D2 connector on the combination meter like you said?
Actually, looking back up at what 1NZ posted, when you are using the console switch, it gets connected across pins 3 and 4, so it acts the same as the stalk switch. The key is that the OEM pin 3 wire is pulled from the stalk connector and the console fog light switch inserts between the OEM pin 3 wire and the connector. Pin 4 does not get touched or connected to on the connector.
If you just "tapped" your switch onto pins 3 and 4 then that would explain the issue you are having.
what does that mean? If I just "tapped" them?Originally Posted by CTScott ↑If you just "tapped" your switch onto pins 3 and 4 then that would explain the issue you are having.
I mean if you spliced your wires onto the existing wires, as opposed to pulling the pin out of pin 3 and inserting the new wire into pin 3.Originally Posted by cyberfrogg ↑what does that mean? If I just "tapped" them?
oooohhhhh! No, I didnt do that. I just inserted the wires with the existing ones. Blue into pin 3 and green to pin 4. Was I supposed to remove the existing wire in pin 3? what would that do?
The pin 4 connection is the big issue I believe. Only the OEM wire should be connected there.Originally Posted by cyberfrogg ↑oooohhhhh! No, I didnt do that. I just inserted the wires with the existing ones. Blue into pin 3 and green to pin 4. Was I supposed to remove the existing wire in pin 3? what would that do?
Try this:
1. Disconnect both of your wires from Pins 3 and 4.
2. Pop the pin out of pin 3 (or, if your harness just has bare ends, snip the wire going to pin 3, leaving an inch or so to connect to.
3. Connect one of your wires to one side of the snipped wire (harness side) and the other to the other side (connector side).
okay I'll do that when I get home. =] thanks!
I hope this works!
I hope this works!
The relay from what i have been told should also have a
inline resister as per photo of this relay
inline resister as per photo of this relay
1 attachment not included in this copy
Originally Posted by PK198105 ↑exactly the Yaris is already prewired, the only harness you need is the one to connect the Fogs together and to the fuse box in the engine bay.
Purchase the foglight stalk. The install is SOOOOOO much simpler and no messing with firewall and interior wiring. Plus, the fog light stalk is how it would come if you ordered your car with fogs from Toyota factory directly.
Purchase the foglight stalk, I don't think the default headlight stalk can handle fog light control. The install is SOOOOOO much simpler and no messing with firewall and interior wiring. Plus, the fog light stalk is how it would come if you ordered your car with fogs from Toyota factory directly.Originally Posted by mrbond ↑So, let's see if I understand this. If I wanted to use the factory stalk instead of the little button that goes into the console, then all I need to do is wire up the fog lights, put the wire into the fuse box in the engine bay, and then put the relay where it's supposed to go? So I wouldn't even need that extra wiring harness for the cabin? If so, that's fantastic.
For sure, I'm definitely doing this. I don't like messing with electrical stuff - too complicated.Originally Posted by Meteorite_Marty ↑Purchase the foglight stalk, I don't think the default headlight stalk can handle fog light control. The install is SOOOOOO much simpler and no messing with firewall and interior wiring. Plus, the fog light stalk is how it would come if you ordered your car with fogs from Toyota factory directly.
This post gives links to order the RELAY and FOG LIGHT STALKOriginally Posted by mrbond ↑For sure, I'm definitely doing this. I don't like messing with electrical stuff - too complicated.
Fog Lights
Thanks all. I installed the foglights and figured that I don't HAVE to have the foglight indicator on in the instrument panel since it indicates "on" on the button itself.
If you had used the fog light stalk, then the bonus to that is the dash indicator comes on when you turn on the fogs. Totally like factory.Originally Posted by yarisugi ↑Thanks all. I installed the foglights and figured that I don't HAVE to have the foglight indicator on in the instrument panel since it indicates "on" on the button itself.
This is the way I did mine.
I tried doing this and it didn't work... My fog lights would not turn on. I snipped the original yellow wire in pin 3 and connected my green wire to it (so now the green wire is connected to pin 3 directly) and then I got my blue wire and connected it to the other piece of the yellow wire that was hanging.Originally Posted by CTScott ↑The pin 4 connection is the big issue I believe. Only the OEM wire should be connected there.
Try this:
1. Disconnect both of your wires from Pins 3 and 4.
2. Pop the pin out of pin 3 (or, if your harness just has bare ends, snip the wire going to pin 3, leaving an inch or so to connect to.
3. Connect one of your wires to one side of the snipped wire (harness side) and the other to the other side (connector side).
this is what it looked like before:
Picture not included in this copy
And it looks something like this now:
Picture not included in this copy
(the black rectangle on the bottom just represents like the switch of the fogs...)
Did i do something wrong? Now that its wired like this my switch works just as its supposed to but my fog lights wont turn on at all anymore... =/
please help!
What do you mean by switch works just as it's supposed to? Do you mean that when you press the fog switch, the dash indicator comes on, but the lights don't?Originally Posted by cyberfrogg ↑Did i do something wrong? Now that its wired like this my switch works just as its supposed to but my fog lights wont turn on at all anymore... =/
please help!
The fog light symbol on the switch turns along with all my other interior lights, which is good. And when I press the switch, the little led indicator turns on as its supposed to. The only thing is the fog lights themselves dont turn on and therefore the symbol on the dash doesnt turn on. So the lights on the switch do what theyre supposed to do. Before I wired it this way, the little led would be on all the time (except for when I had my fogs in use). So in a sense, it was backwards. And now it works, but my fogs dont turn on...Originally Posted by CTScott ↑What do you mean by switch works just as it's supposed to? Do you mean that when you press the fog switch, the dash indicator comes on, but the lights don't?
How many wires connect to your switch?
Four. This is an old pic I had. Its the only one that kinda shows em.
Picture not included in this copy
I have two Greens, one blue, and a ground... the black one.
One green I have wired underneath the gear shift so that the fog light symbol gets light from it and turns on when I turn on my lights inside.
The other green and the blue are what are messing me up.
Picture not included in this copy
I have two Greens, one blue, and a ground... the black one.
One green I have wired underneath the gear shift so that the fog light symbol gets light from it and turns on when I turn on my lights inside.
The other green and the blue are what are messing me up.
Looking at various DIY's on aftermarket fog installs, it looks like there a couple of different harnesses (with different wire colors, etc.), some of which require modification in order to connect them to the oem fog wiring.Originally Posted by cyberfrogg ↑Four. This is an old pic I had. Its the only one that kinda shows em.
Picture not included in this copy
I have two Greens, one blue, and a ground... the black one.
One green I have wired underneath the gear shift so that the fog light symbol gets light from it and turns on when I turn on my lights inside.
The other green and the blue are what are messing me up.
This one seems to best match your description, and it requires modification to connect to the oem wiring:
DIY (08' USDM Liftback): ESUSE Fog Light Install v2.0
lol thats the DIY i used to wire em up and thats how I got the problem in the first place. I have the exact same fog kit, except for the sedan. And I wired it how the DIY said but then the switch seems to work in reverse... ahhh..
The more I look at this issue, I think that the switch is the issue. The OEM stalk switch is just a switch, connecting pins 3 and 4 on D4. The OEM console switch has the switch isolated from the leds. In the picture of the guts of your switch on that DIY, the switch LED is part of the switch circuit. I think that is what is causing the headaches.
I would modify the switch as follows:
Picture not included in this copy
1. Cut the marked trace.
2. Remove the diode.
3. Solder the two jumper wires as indicated.
4. If the pads for the switch are bridged together (where the word "switch" is between two sets of 3 pads), separate them. The switch is a dual pole switch, which allows it to separately switch the two circuits.
I would modify the switch as follows:
Picture not included in this copy
1. Cut the marked trace.
2. Remove the diode.
3. Solder the two jumper wires as indicated.
4. If the pads for the switch are bridged together (where the word "switch" is between two sets of 3 pads), separate them. The switch is a dual pole switch, which allows it to separately switch the two circuits.
I'm sorry I am so confused.. I don't know anything about wiring/electricity and stuff... Can you clear things up..?Originally Posted by CTScott ↑The more I look at this issue, I think that the switch is the issue. The OEM stalk switch is just a switch, connecting pins 3 and 4 on D4. The OEM console switch has the switch isolated from the leds. In the picture of the guts of your switch on that DIY, the switch LED is part of the switch circuit. I think that is what is causing the headaches.
I would modify the switch as follows:
Picture not included in this copy
1. Cut the marked trace.
2. Remove the diode.
3. Solder the two jumper wires as indicated.
4. If the pads for the switch are bridged together (where the word "switch" is between two sets of 3 pads), separate them. The switch is a dual pole switch, which allows it to separately switch the two circuits.
thanks..
In a nutshell, the switch that came with the kit was designed to be used with the kit, not to be used with the OEM wiring. In order for it to work correctly with the OEM wiring, it needs to be modified. The two easiest fixes without modifying the switch would be to get either an OEM fog light stalk, or the OEM fog light switch.Originally Posted by cyberfrogg ↑I'm sorry I am so confused.. I don't know anything about wiring/electricity and stuff... Can you clear things up..?
thanks..
oooooohhh!!! Sorry! I was at school and didnt see there was a picture there... Im understanding it more. my only questions are:
How do I open the switch to see what the picture shows?
where/what is the diode?
what are the two jumper cables and where do I solder them?
and what do u mean by "If the pads for the switch are bridged together (where the word "switch" is between two sets of 3 pads), separate them."?
sorry again and thanks...
How do I open the switch to see what the picture shows?
where/what is the diode?
what are the two jumper cables and where do I solder them?
and what do u mean by "If the pads for the switch are bridged together (where the word "switch" is between two sets of 3 pads), separate them."?
sorry again and thanks...
Wow CTScott. I don't know what the heck is that, but it sure looks like you know your stuff! :) U DA MAN!
Cyberfrogg, if you really want everything to work like factory then it looks like you got a lot of work to do. I think most people just install the kit as-is and don't even bother with getting it to work like factory. But good luck anyway!
Cyberfrogg, if you really want everything to work like factory then it looks like you got a lot of work to do. I think most people just install the kit as-is and don't even bother with getting it to work like factory. But good luck anyway!
Originally Posted by cyberfrogg ↑oooooohhh!!! Sorry! I was at school and didnt see there was a picture there... Im understanding it more. my only questions are:
How do I open the switch to see what the picture shows?
where/what is the diode?
what are the two jumper cables and where do I solder them?
and what do u mean by "If the pads for the switch are bridged together (where the word "switch" is between two sets of 3 pads), separate them."?
sorry again and thanks...
To open it, there should be two tabs about 3/4" above the connector that can be pressed in to pull the connector and circuit board away from the housing.
The diode is the orange and black device.
The "jumpers" are two pieces of insulated wire that you will need to strip the ends of a solder them between the indicated endpoints.
By bridged I mean connected. They may have a silver solder blob (silver) connecting them or there may be a trace (shiny green) connecting them.
I can't thank CTScott enough for all of his contribution here. Everytime I needed wiring help, I just search and almost guaranteed that I will find the answer from one of his postings.
Anyway, I PM'd him today about getting my fog lights instrumental panel indicator lights to come on. I hope someone can benefit from this information in the future:
As for the end result?
Tada!!!! Thanks CTScott 👍
Picture not included in this copy
-toy
.
Anyway, I PM'd him today about getting my fog lights instrumental panel indicator lights to come on. I hope someone can benefit from this information in the future:
Originally Posted by CTScottOriginally Posted by toy_torontoHi CTScott, sorry to bother you but you seem to be the resident guru here in terms of electical wirings.
I got my fogs hooked up the "old school" way, no factory stalk switch, no factory harnes, etc. except I used the supplied switch and relay with the kit and tapped on the car's existing 12V constant feed and 12v ACC (just in case i leave the fog lights switch to ON unintentionally they turn off when I take the keys off the ignition). The OEM-style switch and kit relay are all mounted electrically sound, and the way my fogs are wired is completely independent of the low/hi beam/park light status. I turn it on or off on demand.
The only thing I would like to have now is to have the intrumental panel fog lights indicator to turn on/off depending on the status of my fogs.
Your post below seems to be simple enough to follow.. is this the definitive way to fire that dash fog indicator light on or off? There seems to be some confusement as I read the rest of the thread.
need help: foglight indicator - where are the wires?
Thanks 🙂
Originally Posted by CTScott ↑Or, if you're installing aftermarket fogs without the stalk switch, you can fire the indicator directly by supplying 12V to the red wire on Pin 7 of the D2 connector on the combination meter.
Picture not included in this copy
Ah Yes - That tends to happen in those kinds of threads. But, yes supplying +12 to the red wire when your fogs are on will make the indicator light up.
As for the end result?
Tada!!!! Thanks CTScott 👍
Picture not included in this copy
-toy
.
Mine lights up too. Looks factory...because it IS!👍
Thanks to CTScott! 🎉
Picture not included in this copy
Picture not included in this copy
I know this is an old thread, but after going thru all the threads about the indicator on the cluster, i feel this route is the easiest since i dont know how my factory wired aftermarket fogs were connected. But one thing is for sure, it doesnt turn the indicator on the cluster on.
question then is, what is the easiest way to get the 12v to run into this d2-pin7 wire once the fogs are turned on? (What came to.mind was tapping the switch but which one? worse,tapping into the live wire going into the fog.)
I have esuse with 2 green wires and black and blue IIRC, basically a total of four--similar to the one above.
Tia.
question then is, what is the easiest way to get the 12v to run into this d2-pin7 wire once the fogs are turned on? (What came to.mind was tapping the switch but which one? worse,tapping into the live wire going into the fog.)
I have esuse with 2 green wires and black and blue IIRC, basically a total of four--similar to the one above.
Tia.
Since you have the ESUSE foglight kits, please read THIS THREAD. It should answer most or all your questions.
thanks yarisugi. yes it does, and honestly i'm thankful for that thread. However, i still have two items that are stopping me from following that (thus the d2 connector option im leaning towards):
1) i am unsure as to whether my cluster has a fog light indicator, that's why i need the D2 connector way (if possible) to check if it does
2) i cant seem to find the wiring (or at the least figure it out) of this esuse wiring that the factory installed. moreover, they might have gone a unique route of wiring this up. if i can get the lower kick panel to come off, i probably will be able to see better--rather than the sunglass holder only coming of--again, thus the D2 connector route..
1) i am unsure as to whether my cluster has a fog light indicator, that's why i need the D2 connector way (if possible) to check if it does
2) i cant seem to find the wiring (or at the least figure it out) of this esuse wiring that the factory installed. moreover, they might have gone a unique route of wiring this up. if i can get the lower kick panel to come off, i probably will be able to see better--rather than the sunglass holder only coming of--again, thus the D2 connector route..
Start by shining a flashlight on the cluster. You will see all of the unlit indicators, including the foglight one (if it is there).Originally Posted by jcboy ↑thanks yarisugi. yes it does, and honestly i'm thankful for that thread. However, i still have two items that are stopping me from following that (thus the d2 connector option im leaning towards):
1) i am unsure as to whether my cluster has a fog light indicator, that's why i need the D2 connector way (if possible) to check if it does
2) i cant seem to find the wiring (or at the least figure it out) of this esuse wiring that the factory installed. moreover, they might have gone a unique route of wiring this up. if i can get the lower kick panel to come off, i probably will be able to see better--rather than the sunglass holder only coming of--again, thus the D2 connector route..