Replies continued
kyotenuevo mexico · May 18, 2012#101i didn't notice this thread until I already did the job, and apparently I over-torqued the nuts. i was assuming they were crush washers like on my honda. is this a problem?
also, my oil was very dirty at 26k.
ijose 845Orange County, NY · May 18, 2012#102hey i did my gear oil change i added 2 quarts and nothing leaked out? im guessing it didnt it didnt need to level itself out? should i add more? or just leave it the way it is
Hersheynortheast · May 18, 2012#103The 2 qts. will be fine .
dfhnpdxoregon · Aug 3, 2012#104Thanks, ttufrosty...This is how I will be spending my Saturday morn. Great DIY post...
The SpectacleTampa, FL · Jan 2, 2013#105Great DIY and I just want to give a few notes for anyone tackling this in the future.
- I didn't do this on my car until 75k. The fluid came looking brand new with no metal shavings. However, I was having some issues with the shifter being stubborn in cold weather, especially reverse. After the fluid change, the tranny shifts better than it did stock (as far as I remember)
- A lot of people are recommending Redline, Royal Purple and other exotic oils...you don't really need that stuff. I used Pennzoil Syncromesh out of Autozone for like $8 a quart and it like I said, it shifts better than it did brand new. For reference, here's what it looks like:
http://pennzoil.com/other-car-produc...mission-fluid/ - The 24mm socket size for the fill plug was impossible to find in 1/4 inch. I ended up buying a 1/2 to 1/4 adapter to do the job.
- Buy whatever you need so you can do the fill from the top. I used a hand-actuated vacuum pump that I used to bleed brakes and it was a major PITA to do under the car. I did my best to put all 2qts in, but really as long as you can stick your finger in the fill hole (lol) and feel fluid, you've got enough in there.
yaris2010RSAngus, Ontario · Jan 3, 2013#106To add^ its alot easier to fill the fluid from the reverse sensor port
DeathBeardLos Angeles, CA · Jan 6, 2013#107Where is the reverse sensor plug located, seems like a less messy way than filling from the bottom? Can someone take a picture
Fatty LumpsKansas · Jan 27, 2013#108Just want to give a thank-you for the DIY. Made the job simple for me, faster than changing the oil.
I'm also interested curious about the reverse sensor fill method if anyone has a reference image?
YarisPHPhilippines · Feb 16, 2013#109Hi guys! First post here but been lurking for a while. Just wanna say thanks to the one who made this DIY guide! I used 2 quarts of Redline MT-90 on our 2008 Vios (Yaris sedan's name here in the Phils.). Car has 42K ++ kilometers on the ODO. Will observe the gear changes later on, as I've read a lot of good feedbacks on this oil. Many thanks again Yarisworld. :)
hw6515U.S · Mar 28, 2013#110hw6515U.S · Mar 28, 2013#111Hersheynortheast · Mar 28, 2013#112Hersheynortheast · Mar 28, 2013#113regalPA · May 17, 2013#114Anyone have a part number for the drain plug washer?
jason214Halifax NS · May 17, 2013#115Drain/Filler Plug P/N: 90341-18033
Drain/Filler Plug Gasket P/N: 90430-18008
Hersheynortheast · Jun 9, 2013#116Well done 👏 . On occasion during an oil change I drop the drain bolt in the oil bucket and have to fish around for it 😛 . Keep us informed on any improvements with the new fill . Well worth the mess .
Hersheynortheast · Jun 9, 2013#117Can't go wrong at that price . Lady luck must be on your side .
7:34pmBritish Columbia · Jul 4, 2013#118Sorry but my Yaris is base model and didn't come with an owner's manual.
What type of fluid is recommended for the 5spd manual? Is it 75w90?
thanks
bronsinnj · Jul 5, 2013#119Wilbro how did your engine compartment get so dirty? 🤷
I hope you changed the AF too! 😲
Nigel8600Calgary AB · Oct 25, 2013#120I was having the same problem shifting into first (at a very slow speed, maybe 2MPH?) so I found this thread and changed my gear oil to MT90 2 days ago. I cant believe how smooth it shifts now, its like butter........ BUT............. it still grinds when going into first... even when going into 2nd gear just before. Agghhhh
Hersheynortheast · Oct 26, 2013#121Let us know if the grinding disappears over a period of time .
En4sirNE Pennsylvania · Apr 18, 2014#122After purchasing my 2009 3-door hatchback new and putting 165,000 miles on it I decided today (after reading this thread) to change my manual transmission fluid. I followed the advice offered by many here and would like to add a few little tips that I did that should benefit others.
I took some 2-foot long 2" x 8"'s scrap I had laying around and placed a section of 2" x 8" in front of each tire. I then drove the car onto the lumber to increase the ground clearance by another 1.5 inches. It may not sound like much but every bit helps especially when gaining access to the drain plug underneath the car without having to use a jack.
I loosened-up the filler plug just enough to make sure that it could be removed, then removed the drain plug. Draining the transmission fluid without removing the filler plug prevented the transmission fluid from gushing out. After draining about a quart of fluid I then removed the filler plug to allow the transmission to drain completely. No messy spillage anywhere.
I attached a clear vinyl hose 5/8"od / 1/2" id to a small funnel. The hose fit perfectly in the filler hole of the transmission - nice and snug.
Unfortunately I could not find Redline MT90 anywhere locally, so I decided to use Amsoil Severe Gear SAE 75W-90. I referenced the Amsoil website to make sure it could be used in my Yaris.
I test drove the car afterwards and there is a noticable difference in how the transmission shifts - nice and smooth.
Thanks to all the valuable advice posted here in this thread, a job that my local Toyota dealer wanted a $198.95 to do, I did for $25.00 and it took a total of 25 minutes to do.
frambachMurfreesboro, TN · Apr 20, 2014#123 Originally Posted by
En4sir ↑ I decided to use Amsoil Severe Gear SAE 75W-90. I referenced the Amsoil website to make sure it could be used in my Yaris.
I test drove the car afterwards and there is a noticable difference in how the transmission shifts - nice and smooth.
Thanks to all the valuable advice posted here in this thread, a job that my local Toyota dealer wanted a $198.95 to do, I did for $25.00 and it took a total of 25 minutes to do.
I used Severe Gear as well. I have put 30,000 miles on the lubricant and have been well pleased.
AMSOIL lists Severe Gear as a GL-5 product. Can anyone find (in writing) where Toyota says the Yaris C50 has to have a GL-4? Just curious, I'd like to see it.
When a transmission MUST have a GL-4, AMSOIL makes sure they recommend a GL-4. On the Yaris, the first recommendation is a GL-5.
rningonfumesSoCal · Apr 20, 2014#124I don't think you'll find anything in writing from the manufacturer that GL-4 is for the Yaris. It's just a general consensus that GL-4 is reviewed by members to feel better for their Yaris. If you search any of the terms ie GL-4 and you'll find that it works better for our synchros among other things.
Here is one particular thread:
GL-4 or GL-5 Originally Posted by
1stToyota ↑ You probably should have used AMSOIL 75W-90 GL-4 Transaxle Lube...it's what I used and GL-4 is better for the transaxle than the severe gear GL-5, which is meant for differentials.
Nice and succint from this thread:
Transmission Fluid - My car is ruined - help Hersheynortheast · Apr 20, 2014#125GL-4 is preferred . The AMSOIL Manual Transmission and Transaxles Gear Lube is GL-4 . If it's not giving poor shifting ( grinding , etc. ) you should be fine .
sheekeebutMississauga, GTA, Toronto, ON · Jun 28, 2014#126Drove my lowered sedan onto 1" thick concrete tiles at the front. Just enough space to floor jack the front up and start working. Thanks OP, you've saved me $200+ in quoted service fees, plus given me some knowledge every Yaris enthusiast should have.
For the record: Motomaster synthetic 75W90, GL-5.
If our manual says says GL-4 OR GL-5, then I shouldn't worry so much about using GL-5. The Toyota engineers would be in deep trouble if they designed a gearbox without considering that they prescribed an oil grade that can harm yellow metals.
spookybathtubCalifornia · Aug 30, 2014#127 Originally Posted by
CoryM ↑ Make sure your vent is clear as well. The transmission has a vent on it to allow for the expansion of the oil/air inside. Otherwise the seals have to deal with the pressure and will eventually fail. These vents often clog, and mine was plugged when I got the car with 38000km on it. A good indicator it is plugged is you will hear a hiss of air as you open the fill plug.
Cory, how did you clean the vent? When I removed the filler plug, some air hissed out, so apparently my vent is clogged. From the photo you posted, I can't figure out where it is. Is the vent a bolt, or simply a hole? Can it be cleaned with a squirt of compressed air?
tmontagueCaledonia Ont. · Aug 31, 2014#128I wouldn't mind knowing where that vent is either. I have changed my trans oil at 87,000km when I got my Yaris but will be doing it again before the winter as I'm at 122,000km and I want to put synthetic in. I didn't hear any air release the first time I did it but I'd like to check it.
spookybathtubCalifornia · Aug 31, 2014#129I looked around yesterday, and I think I found it where Cory labeled in that drawing. After removing the air box, it's visible from the top. It's an aluminum cap about 1/2" diameter and 3/4" tall. It spins freely, and I pulled it off with vise grips. It looked totally clean under the cap, but I blew it off with canned air anyway.
donpalinoNewton, MA · Sep 8, 2014#130 Originally Posted by
CoryM ↑ A suggestion to all owners, but specifically while doing this job:
Make sure your vent is clear as well. The transmission has a vent on it to allow for the expansion of the oil/air inside. Otherwise the seals have to deal with the pressure and will eventually fail. These vents often clog, and mine was plugged when I got the car with 38000km on it. A good indicator it is plugged is you will hear a hiss of air as you open the fill plug.
I can't recall exactly where the vent is on these cars. iirc it's just behind the shifter. A little white(?) plastic knob that you twist and wiggle a little to free up any junk.
I'll try to find a picture.
Cheers.
Driving a 2010 Hatchback, 5 door, manual with 80K miles
Came back from the dealer after replacing the axle seal, which showed some leaking. Opened the filling cap and heard the hiss so I am sure I have to clean the vent. Now waiting for the MT-90.
Thanks for all the inside info.
ExiwolfmanWasaga beach · Sep 8, 2014#131 Originally Posted by
spookybathtub ↑ I looked around yesterday, and I think I found it where Cory labeled in that drawing. After removing the air box, it's visible from the top. It's an aluminum cap about 1/2" diameter and 3/4" tall. It spins freely, and I pulled it off with vise grips. It looked totally clean under the cap, but I blew it off with canned air anyway.
And now ur gone have to replace it with new ...they are not to be removed ,caps that is ...if stuck spray penetrating fluid free it up clean off with brake clean .
They are also used on the axles on Tacoma and tundra almost all Toyota's .
sent from my S4 on Mars
spookybathtubCalifornia · Sep 8, 2014#132Mine went back on just fine... what's the problem?
ExiwolfmanWasaga beach · Sep 8, 2014#133No problem... Just saying no need to take it apart and risk damage yours may or maybe not ok that's all
sent from my S4 on Mars
donpalinoNewton, MA · Sep 16, 2014#134attraperevesKCMO · Feb 12, 2015#135Just changed mine. I used RedLine. There is a noticeable difference in shifting.
valchrist90731Los Angeles County · Jul 18, 2015#136 Originally Posted by
Henry G. ↑ Royal Purple is average stuff at best. Read the technical reviews.
Redline MT-90 is top notch stuff. This is a 15 minute job at worst if you have the right tools. You will notice smoother shifting and that grinding while going into reverse will all but disappear. Its a no brainer especially if you drive 25k miles a year like I do.
If your grinding while shifting into reverse. Learn from your mistakes. Put the car into first gear then shift it in reverse. Grinding is due to the driver most of the time.
Have patience with your car and it will drive smoother.
This was to inform all on how to reduce grinding when shifting into reverse.
This was written respectfully as possible.
07liftbackBay Area · Oct 25, 2015#137Just got two quarts of the Redline MT-90 GL-4 Transmission fluid from ebay for $34 shipped. Hopefully it fixes my occasional second gear and reverse gear grind.
fnkngrvIn The Hotbox · Oct 25, 2015#138 Originally Posted by
valchrist90731 ↑ If your grinding while shifting into reverse. Learn from your mistakes. Put the car into first gear then shift it in reverse. Grinding is due to the driver most of the time.
Have patience with your car and it will drive smoother.
This was to inform all on how to reduce grinding when shifting into reverse.
This was written respectfully as possible.
I will be as respectful as possible as well. This issue with shifting into reverse with the stock or other conventional fluod is a known issue. Expecting someone to shift into first just to shift into reverse is unacceptable. Telling someone to be patient isn't a cure to the problem. Sure, it is possible that drivers are over anxious to shift, but the issue has even been noted in published reviews. Once again reviewers could be over anxious to shift, but they have experienced many many manual transmissions in most cases so they have firm ground to stand on regarding the behavior. I have driven a few dozen different manuals from various vendors and have experienced this only on well worn transmissions not brand new ones. I had the issue within the first 1000 miles. Changed to synth and bam, resolved. There is a reason why so many manufacturers are switching to even requiring synthetic; it is a much more tolerant and better working lubricant.
Sent from my SCH-I545 using Tapatalk
tmontagueCaledonia Ont. · Oct 28, 2015#139Just sources some Redline MT-90 from a local store near me for $21 a quart, not too bad a price. I'll be picking it up later this week and putting it in this weekend.
I get a slight quick grind when shifting into reverse in the morning in my driveway and I'm currently running 75w90 synthetic. Not much better than oem just a little thinner in the dead of winter.
I'll leave my thoughts on here once I test it out.
tomm9050CA · Oct 31, 2015#140GL-4 or GL-5 WHat's the difference. What's the verdict on what's best?
Thx
tmontagueCaledonia Ont. · Nov 1, 2015#141GL-4 seems to be what give much smoother shifting over GL-5. I've installed my GL-5 tranny fluid but haven't driven the car to try it out yet.
tomm9050CA · Nov 3, 2015#142strandrrsNC · Feb 10, 2016#143Hi -
I have a 2009 5-door hatchback Yaris.
Thanks for the great DIY instructions and photos - so helpful.
Can I just add the Toyota transmission fluid there? Do I have to drain it? If so, can I drain it from the bottom, the same way as the manual?
Thanks so much!
AclosefriendPhiladelphia · Mar 5, 2016#144Thanks for this. I bought a 08 Hatchback a few months ago with a 5 speed MT with 65k miles. This was so easy and the shifting is much much smoother now. Only took 20 minutes, and most of it was waiting for the fluid to drain and for the fresh thick gear oil to flow down the tube.
dogsridewithUSAnotCA · Jan 29, 2017#145 Originally Posted by
Aclosefriend ↑ Thanks for this. I bought a 08 Hatchback a few months ago with a 5 speed MT with 65k miles. This was so easy and the shifting is much much smoother now. Only took 20 minutes, and most of it was waiting for the fluid to drain and for the fresh thick gear oil to flow down the tube.
Which oil did you go with?
Rigo93shredhouston texas · Jul 22, 2018#146I just got a yaris 2 door hatch 5 speed with 105k miles and idk if the tranny oil has ever been changed it shifts nice never had a standard but i dont hear grinds or anything in mine the previous owner had it for 3 years and never mentioned trany oil change should i change it along with all fluids just to start fresh or would new oil mess up my tranny cuz its good i sort of cant stand not knowing if its clean or not and if its never been changed should damage happen to it???? Sorry for the long post 1st car and i wanna baby it good
timbstirUSA · Sep 7, 2018#147So I did my gear oil yesterday and I took the fill plug off first, and when I did oil started to pour out (less than a quart), did this happen to anyone else?
tmontagueCaledonia Ont. · Sep 7, 2018#148That is fine it just likely wasn't overfilled before due to the front end being jacked up higher than you had it.
FWIW I over fill my trans fluid by about half a quart
IllusionXBrossard, QC · Sep 7, 2018#149Not much came out when I did mine. Had a flat surface though.
Then poured 2qt in, small quantity came out and that's what I left it at.
Sent from my VTR-L09 using Tapatalk
timbstirUSA · Sep 7, 2018#150Yeah it wasn't much that I had pour out, it was up on jack stands. The worst part was that I wasn't anticipating it so I didn't have a catch pan ready at the time so I had to spend the next half hour trying to clean my friend's garage. I put in about to quarts on level ground afterwards and it seems to be doing fine, it shifts way smoother than before.