ttufrostyOriginal postDFW, USA · Sep 15, 2007#1It is not that difficult to do. If you can change the engine oil you can probably do this. Though the nuts are a little bit tougher to get at. I did not put my car up on jacks but was still able to squeeze my 6 foot 200 pound frame under enough to do all the work.
Keep in mind I am making no GUARANTEES on this work. What you do is at your own risk. If you dont feel you can do the work. THEN DONT. It is basically a few simple steps.
1. Locate the nuts to be removed.
Drain plug - Viewed from under the drivers side tire and looking back. Notice Big White Sticker.
Fill plug - Viewed from top of car looking down from next to air box. Use as a point of reference to find from bottom. Same big white sticker.
2. Loosen the fill plug
FIRST with a
24mm socket.
Do not skip this step. If you remove the drain plug first and cant get the fill plug off you are screwed.
3. Loosen the drain plug use same
24mm socket. Place an oil pan underneath. Then completely remove the drain plug. The oil will come gushing out. Now would be a good time to drink a beer (If you are of age) and let the oil drain out.
4. Replace the drain plug and gasket (if gasket is worn replace) and re-tighten to
29 foot-lbs of torque.
5. To fill from the top you need to jury rig you a little fill tool. I got about a 3 foot length of vinyl tubing and attached it to the end of my funnel. Then I ran that down to the fill plug from the top.
6. Remove the fill plug and gasket. Insert the tubing into the fill hole. Will require you to lower the tube from the engine compartment and then insert the tube from below.
7. Add oil to funnel. I used
Royal Purple 75w-90 Max Gear Oil, but any brand will do so long as it meets the specs required by Toyota.
2 quarts will do.
8. Oil going into car from top.
9. Oil going into car from bottom.
10. Once you have put all 2 quarts in, go ahead and remove the tube, but make sure the oil pan is under the fill plug. The car requires 2 quarts but with the little bit of remaining oil from before and the 2 quarts you have added there will be some extra. Wait until it levels off. Don't worry the correct amount of oil is supposed to be 0.05mm below the fill plug. So once it levels off it should be correct.
11. Put the fill plug and gasket back on and re-tighten to
29 foot-lbs of torque.
Your done. Check for leaks. Drive nicer shifting car.
If you need clarification on anything I have done let me know and I will try and give you an answer as to how I did something.
And if I did something completely wrong. Please let me know so it can be fixed and no one else does it.
Enjoy.
Replies 149
uncleyarisToronto · Sep 15, 2007#2Great dIY!! BTY how many miles did you have on the car?
ttufrostyThread starterDFW, USA · Sep 15, 2007#329,000k miles, 1 year. I drive about 95 miles a day round trip to and from work.
ttufrostyThread starterDFW, USA · Sep 15, 2007#4The service manual says to check at 30k and replace at 60k. However, since I drive as much as I do and since I was experiencing some grinding of gears especially 1st and 2nd. I decided to switch to synthetic.
The change was more to switch to synthetic rather than because it was due for a change.
nisyotaOrlando, USA · Mar 28, 2009#5cool write-up... i was thinking about going to the dealership cuz i couldn't find the drain plug and fill plug...
Now, my question... I have an automatic sedan... what kind of oil should i use for my tranny? Does Royal Purple or Mobile1 have anything?
Thanks
fujiHonolulu · Mar 28, 2009#6I am assuming this can also be applied to automatic transmission cars as well. Just need different transmission fluid. Any ideas on the specifics of the transmission fluid needed for autos?
nisyotaOrlando, USA · Mar 28, 2009#7looks like on an automatic there is a dip stick... woo hoo. lol
should be the same drain and fill process except that we have to start up the car and move through each gear (slowly at first) and not floor it until you think the oil has gone through the tranny... i think. thats what i have to do on my truck.
on the dip stick it also says that its not necessary to change the ATF on "Normal" driving conditions... hint:hint: NORMAL. even though i have a stock yaris sedan, i still try and race those porsche. LOL
supmetSouthern California · Mar 28, 2009#8for automatics, the ONLY transmission fluid recommended is World Standard Genuine Toyota Transmission Fluid - and its 250 bucks at the stealership.
with that said, I had dexron put in before I read the TSB, and haven't had any problems in 10k miles.
nisyotaOrlando, USA · Mar 28, 2009#9so pretty much the auto guys are screwed... no one makes anything compatible?
PetersRedYarisThe Black Hills of South Dakota · Mar 28, 2009#10 Originally Posted by
nisyota ↑ so pretty much the auto guys are screwed... no one makes anything compatible?
Wal-Marts Super Tech brand of of fluids has two tranny fluids that say right on the bottle they are compatible with With Toyota type WS. But, for the cost ($3 vs $5.50 a quart), I would just go for the genuine WS...
Nice manual tranny DIY...
yaris-meAnaheim, CA · Mar 28, 2009#11Thanks for the DIY. 👍
nisyotaOrlando, USA · Mar 28, 2009#12oh, its only $5.50qt? supmet said it was $250... thats more than my trucks transmission oil.
I guess i don't really have to change it, but for peace of mind, i am. :D
detroiterMetro Detroit · Mar 28, 2009#13I just changed my auto trans fluid about a month or so ago, it was about $8 a quart and it took about 4 of them. $32 vs $250 to have the stealership do something you can do yourself in 30-45 mins.
nisyotaOrlando, USA · Mar 28, 2009#14heck, i should have done that today... $32... thats cheaper than changing the oil. LOL
THANKS FOR EVERYONE'S HELP!!!
I love the DIY section. LOL
MorganPCB, FL · Mar 28, 2009#15Good DIY, You can fill from the reverse sensor or vehicle speed sensor if you don't like side fill (its messy!) BTW the "official" amount is 1.9 qts if you fill from the top - when I had the battery out, both sensors were easy to get to :)
schleppyBoston, MA · Mar 29, 2009#16Fantastic write up! This should be made sticky and added to the DIY manual!
As a side note, a buddy of mine is a Toyota mechanic and he said one of the few things he thinks people need to do more often is change the tranny fluid. He said every 15k if you drive a lot. It's cheap insurance...
IllusionXBrossard, QC · May 22, 2009#17UHHHH..... digging old thread up...
I'm not sure if i did it right, i took ~1 3/4 Quart out only??
Yet, filling it with 2QT did not over fill it. Or i now i have too much oil in there??
ShroomsterOrlando · May 22, 2009#18just to clarify for those of us with auto transmissions....what you all are doing is just draining and filling the trans pan.
what supmet stated was $250 was probably a fluid exchange (flush and fill)
which takes all the fluid out including that in the torque converter.
IllusionXBrossard, QC · May 22, 2009#19this clearly states manual transmisison...
ShroomsterOrlando · May 22, 2009#20 Originally Posted by
IllusionX ↑ this clearly states manual transmisison...
yeah and for some odd reason a few posts up someone was questioning this topic for their auto tranny. sorry for the mis-confusion
andacondaMontana · Sep 13, 2009#21 Originally Posted by
IllusionX ↑ UHHHH..... digging old thread up...same go's here!
Going to change to "Amsoil Synthetic Manual Transmission and Transaxle Gear Lube 75W-90 API GL-4 (MTG)" after 7000 miles on the odometer. I have ground way too many gears from lack of pressing the clutch in all the way. I will feel better about getting the original gear lube out of the tranny.
I don't have a 24mm socket but the 15/16 I have fits well. The conversion is 24mm = 15.118/16 inch. Should I use my 15/16, or go buy a 24mm?
LazerdotEuless Texas · Sep 13, 2009#22I bet a good 24mm socket would be worth having. All my tools are with my Karts, leaving me with standard tools(and few of um), really like having metric around.
Doin the same with my car soon..., only 14k on it though. AX might be beating it up some though. Sooner the better I guess.
advocatelocation · Sep 13, 2009#23 Originally Posted by
ttufrosty ↑ I was experiencing some grinding of gears especially 1st and 2nd. I decided to switch to synthetic.
Did you notice smoother shifting after the oil change?
edit: just noticed this was a necro'd thread. damn my luck.
MUSKOKA800Chatham, Ontario, Canada · Sep 20, 2009#24 Originally Posted by
andaconda ↑ I don't have a 24mm socket but the 15/16 I have fits well. The conversion is 24mm = 15.118/16 inch. Should I use my 15/16, or go buy a 24mm?
I used a 15/16" (6 point impact type) socket today when changing over to synthetic. It fit just fine. 👍
UTVitzSalt Lake City · Sep 21, 2009#25I made the switch to Redline MT90 a month ago-big difference-I have not missed a shift since it's that smooth. MPG's seem to stay in the mid-to high 40's now rather than the lower 40's before. Very much worth the $24 for two quarts of the stuff. I tried Mobil 1 gear lube at first-but learned that is a GL-5 and although that's ok according to Toyota it was not prefered as GL-4 was-so I through $18 away on some mobile 1 by mistake. Very happy with the Redline MT90 in the Yaris.
bronsinnj · Sep 22, 2009#26What makes that oil purple? Purple dinosaurs? Food coloring?
mikenacaratoBrentwood, TN · Sep 22, 2009#27bronsinnj · Sep 22, 2009#28I know....snails!
mikenacaratoBrentwood, TN · Sep 22, 2009#29apparently you cant read.
bronsinnj · Sep 23, 2009#30They said its purple because its the color of royalty. But they didnt say how they made it that way.
Henry G.So Cal. · Sep 25, 2009#31Royal Purple is average stuff at best. Read the technical reviews.
Redline MT-90 is top notch stuff. This is a 15 minute job at worst if you have the right tools. You will notice smoother shifting and that grinding while going into reverse will all but disappear. Its a no brainer especially if you drive 25k miles a year like I do.
ddongbaphay · Sep 26, 2009#32I'm rocking NEO oil.
dorman68Pa · Sep 30, 2009#33Great write up!!
andacondaMontana · Oct 17, 2009#34 Originally Posted by
andaconda ↑ Going to change to "Amsoil Synthetic Manual Transmission and Transaxle Gear Lube 75W-90 API GL-4 (MTG)" after 7000 miles on the odometer. I have ground way too many gears from lack of pressing the clutch in all the way. I will feel better about getting the original gear lube out of the tranny.
I don't have a 24mm socket but the 15/16 I have fits well. The conversion is 24mm = 15.118/16 inch. Should I use my 15/16, or go buy a 24mm?
Followup:
I did the change to Amsoil.
A couple of tips tho:
I jacked up the drivers side of the car so that I could get to both plugs easier - but while I was draining, I let the car down off the jack, and then jacked it back up again to finish the job.
I did use my 15/16 socket with no problem.
Have the pan ready - I mean really ready - when I pulled out the filler plug, it came gushing out and missed my pan by a mile -- like all over the frame members, all over the jack, all over the driveway -- So be ready for it!
Have a helper on top with the fill funnel while you hold the fill tube in the fill hole -- you don't want to waste a precious drop of this expensive gear lube.
Don't over tighten the plugs. They're not that tight - 29 foot pounds.
Now I can't honestly tell any difference, but the cold weather hasn't come yet and I don't have but a couple of miles on it.
But at least I know it is changed out and I feel better about it.
My kid has been ribbing me about this switch from dino to synthetic. He said "you'll do anything to squeek one more mile per gallon, won't you!"
jamal1984Georgia, USA · Oct 17, 2009#35the pictures is down, can someone reupload it?
schleppyBoston, MA · Oct 30, 2009#36I put in AMSOIL MTG (
http://www.amsoil.com/catalog.aspx?code=MTGQT-EA). I only have 9500 miles on the car, but it made a difference. There is less resistance in the gearbox at all speeds, especially low speeds. I've heard it only gets better with time.
I had access to a lift, but the job was VERY simple. I could have done it without a lift easily. Get yourself a funnel with a long tube, two quarts of fluid, and a 15/16th wrench.
It's worth doing. I'll probably change the fluid again in 20,000 miles. Why not?
Boost AddictedAlbany NY · Jan 2, 2010#37 Originally Posted by
Shroomster ↑ just to clarify for those of us with auto transmissions....what you all are doing is just draining and filling the trans pan.
what supmet stated was $250 was probably a fluid exchange (flush and fill)
which takes all the fluid out including that in the torque converter.
Agreed, however I'm looking at Mitchell On Demand as I type, and it says the automatic transmission fluid capacity is 2.6 quarts, or 2.5 liters... Compaired to that of which another member above replaced 4 quarts.
It just struck me when I saw the capacity vs. what someone else put into the car after a drain. Figured I'd mention the spec..
The manual trans is 2.0 quarts or 1.9 liters.
And to get to my actual point here, I'm wondering how you guys like the Royal Purple? I've heard mixed reviews... I must confess, I'm actually a Volkswagen guy (My girlfriend owns the Yaris) and people weren't too impressed with it in the 6 speed GLI's which is what I have. And I want a REALLY good synthetic for the Yaris (5 spd) because I noticed it has no syncro for reverse, and sometimes when you put it in reverse (yes, with the car stopped) it gives a quick sharp grind and kinda lurches the car slightly. Can't be good... And I don't want metal shaivings causing havoc. So what do you think is the best synthetic trans fluid out there? Thanks guys!
/rant lol
gonzo452001French Lick,IN · Jan 2, 2010#38I put it in my manual yaris I am not that impressed with it on cold morning I feel a little grind when I put it in 3rd gear until it gets warmed up I have been thinking about trying something else
UTVitzSalt Lake City · Jan 2, 2010#39I put Redline MT-90 in this last summer and love it. And now that winter temps are here I couldn't be happier with the decision to use it. I never really notice a cold shift difference vs. warmed up like I used to. And reverse engages a lot smoother than it did before the change. Give it a try-two quarts will set you back about $22 most places.
gonzo452001French Lick,IN · Jan 2, 2010#40I think I will
gonzo452001French Lick,IN · Jan 2, 2010#41shouldn't we use the 75w90 instead of straight 90w
gonzo452001French Lick,IN · Jan 2, 2010#42Ok the mt90 is 75w90 ordered 2qts from amazon
Boost AddictedAlbany NY · Jan 3, 2010#43 Originally Posted by
UTVitz ↑ I put Redline MT-90 in this last summer and love it. And now that winter temps are here I couldn't be happier with the decision to use it. I never really notice a cold shift difference vs. warmed up like I used to. And reverse engages a lot smoother than it did before the change. Give it a try-two quarts will set you back about $22 most places.
Awesome, I was thinking of using the Redline in both her Yaris and my Jetta. I've heard good things, and I can pick it up locally for 12 bones without having to pay shipping. I'll post back up after the fluid change and tell you guy how I feel about it.
Hersheynortheast · Jan 4, 2010#44you won't be disappointed . Takes a little time to get the full benefit . Work through all the gears , including reverse .
sleey0PA · Aug 30, 2010#45Just replaced my MT tranny oil today at 22k miles and WOW! What a damn difference.
Good to get the old gear oil out of there and some new - I bought the car used at 19k miles and who knows howthe original owner drove it or grinded 'em;) lol
REDLINE 75w90 FTW!!!
Hersheynortheast · Aug 31, 2010#46It's amazing . No more grinding , smoother shifts , and no clunk into reverse . Used it in a '08 we had . Better cold shifting too . Enjoy .
sleey0PA · Aug 31, 2010#47I know it!
I really didn't think it would make a difference ESPECIALLY since the old oil that drained out was very clear and seemed still good.
I wonder what brand and type of oil Toyo uses as the factory fill for the MT tranny.
ShroomsterOrlando · Sep 1, 2010#48^^^something that has a lot of assembly lube in it most likely....
sleey0PA · Sep 1, 2010#49Yeah, you are prob right. lol
DeathBeardLos Angeles, CA · Sep 1, 2010#50Is 75w90 the correct weight for 5 speed?