Yarisworld Archive

Baja Yaris

174 posts · 165,443 views · page 2 of 4

Replies continued

MaritimeThread starterWoodstock nb · Jan 26, 2019#51
Got grinder to work. This much so far. I think it will be plenty strong. Working out how to gain the 1.5" needed under the mount.

Picture not included in this copy

Sent from my moto e5 play using Tapatalk
MaritimeThread starterWoodstock nb · Jan 26, 2019#52
Ok. This is a start. I can do 2 of these. There is 1.5" between the 2 spring perches so now just need something as the meat in the sandwhich.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Sent from my moto e5 play using Tapatalk
myfirstyotaToronto Canada · Jan 27, 2019#53
You might be on to something there sir
MaritimeThread starterWoodstock nb · Jan 27, 2019#54
Trip to ct and found this in the boat.section. high density boat roller. Uv and salt resistant and can carry a huge boat on it.

Picture not included in this copy

Cut an inch and half slice and Roberts your mothers brother.

Picture not included in this copy

Sent from my moto e5 play using Tapatalk
MaritimeThread starterWoodstock nb · Jan 27, 2019#55
Pretty sure it will work fine. Replicate one more and buy the rear spring.spacers and the lift part will be sorted

Sent from my moto e5 play using Tapatalk
myfirstyotaToronto Canada · Jan 27, 2019#56
I'm really hoping I can get to my metal place this week to pick up my bits!

Let us know when you install these. Dying to find out how it works.
MaritimeThread starterWoodstock nb · Jan 27, 2019#57
Originally Posted by myfirstyota ↑
I'm really hoping I can get to my metal place this week to pick up my bits!

Let us know when you install these. Dying to find out how it works.
Will do. Gonna order the rear spacers tonight or tomorrow and will put it all in once they arrive.

Sent from my moto e5 play using Tapatalk
MaritimeThread starterWoodstock nb · Jan 28, 2019#58
So I just pulled the trigger on these, $22CAD shipped off amazon. 1.5" coil spacers. not vehicle specific so hope they fit. Also a set of camber bolts as going up 1.5" will require an alignment I bet.

Picture not included in this copy

Picture not included in this copy
myfirstyotaToronto Canada · Jan 29, 2019#59
Sweet, hopefully Amazon is quick out that way lol

We got a record snowfall for Toronto yesterday. 26+ cm. With just the xd springs and the tires I'm running... this car was unstoppable. I was bombing around stuck SUVs, CUV's and just about everything else on the road. Even 2' snow berms left by the plow were no problem with a bit of momentum. Im guessing 1.5-2" of lift plus a larger tire will satisfy most people's desire for easier mobility in snow.
MaritimeThread starterWoodstock nb · Jan 29, 2019#60
Originally Posted by myfirstyota ↑
Sweet, hopefully Amazon is quick out that way lol

We got a record snowfall for Toronto yesterday. 26+ cm. With just the xd springs and the tires I'm running... this car was unstoppable. I was bombing around stuck SUVs, CUV's and just about everything else on the road. Even 2' snow berms left by the plow were no problem with a bit of momentum. Im guessing 1.5-2" of lift plus a larger tire will satisfy most people's desire for easier mobility in snow.
I saw the snow on the news. We're getting that storm here but only calling for 10-15cm. I know with some clearance the little red car will get through anything. The only time I get stuck is when the bottom hits snow and lifts the tires off the ground. Bits should arrive on Friday, I have to do a bathroom reno so we'll see if I get some time to install the lift.
MaritimeThread starterWoodstock nb · Jan 30, 2019#61
Was perusing the web for roof rack options then remembered I have a Thule setup from my old X-Trail(POS) so I am going to see if I can line that up and mount. Anyone know if the spot under the black rubber is thick enough to drill and tap threads? Generally that's the strongest part of the roof.
MaritimeThread starterWoodstock nb · Jan 30, 2019#63
Originally Posted by WeeYari ↑
So, I'm going to drill some holes in my roof...

Sent from my EML-L09 using Tapatalk
Thanks. I found that right after I typed the question. first time I searched I had a typo and nothing came up LOL. I need to look into the expanding anchors from that thread.
MaritimeThread starterWoodstock nb · Jan 31, 2019#64
Rear spacers are supposed to arrive by tomorrow, Amazon guarantee. Camber bolts are landing in Maine today along with some other bits and bobs I ordered. Hopefully this weekend I can get the lift in, and get the rack out of storage and get it on too. I think I am going to wrap one of my wheels/tires with some foam or cardboard or something to add the width and diameter of the new tires and mount it up into the wheel wells front and back and see if anything is going to rub etc. That way if I need a spacer I can order them before I order the tires.
LeegamerAshland, VA · Jan 31, 2019#65
I'm hoping you will take pics to document!
MaritimeThread starterWoodstock nb · Jan 31, 2019#66
Originally Posted by Leegamer ↑
I'm hoping you will take pics to document!
Yeah I will, I just noticed the links to the pics of all the parts I did are not showing in the thread anymore?
MaritimeThread starterWoodstock nb · Jan 31, 2019#67
Just on my work pc, fine on phone. Looks like our new office 360 is blocking stuff


Sent from my moto e5 play using Tapatalk
justjesusOrange County · Feb 1, 2019#68
Originally Posted by Maritime ↑
tires:
Picture not included in this copy

Lift Kit which will give me 1" front and 1.5" back:
Picture not included in this copy

Maritime
Originally Posted by Maritime ↑
https://www.ebay.com/itm/Complete-li...~vgz:rk:3:pf:0

Looks simple enough, strut top bolt extender and spacer for strut, rear spring seat extender like for jeeps.
I have the General tires on my Jeep XJ. So far, I like 'em enough. For my Yaris, I'm running the prior gen of the BFG All Terrains in 195/70-14 (70, I think). They hold up well for daily driver duty.

Sure enough, when looking at my own Off Road Yaris project, I found some Jeep JK front spacers that may work in the rear of the Yaris. Some measurements were taken, and I *think* they could work. I bought them but never put them on to confirm. I'm pretty sure of it, though.


Originally Posted by Maritime ↑
Ha, that would be rad but way out of budget. I'll be lucky of I can manage a 2ZR swap and afford an LSD when the original motor finally bites the bullet. the lift, tires and rack are all budget friendly.
Originally Posted by myfirstyota ↑
Yea an LSD is about $1600 cad for a quaife. Plus install. Its not a budget friendly mod... But sometime you gotta say f-the budget lol
The LSD, plus the xB final drive ratio, is what I was considering for mine. But, unfortunately, I couldn't say "F- the budget" :( The cost of those two items, plus install, was high enough that I took that money and bought a 1996 Jeep Cherokee (XJ).

If you YouTube "off road yaris" mine should be the first hit. You can see where having an LSD would have helped. But in reality, that stuff I was attempting there IS a bit much for a FWD econobox :) I knew this going in! It did much better on regular dirt trails.

I really hope you get this project going!!!! I still go back and forth on mine.

Also, I'm still kind of tinkering with a way to get the rear lifted, without affecting the shocks, or the angle of the rear beam assembly.
myfirstyotaToronto Canada · Feb 1, 2019#69
I think you'll have to make rear axle drop brackets if you don't want the angle of the axle affected. I plan on a 3-4" lift and I'm just gonna push that axle down. It will be way too much fab work to make axle mount drop brackets. I took a quick look one day to see if some sort of bolt in drop brackets could be made. Didn't look remotely easy to me.

Praying I can get my spacer bits next week. Didn't have time to get to the metal place before 5 this week :(
Type-YNY · Feb 3, 2019#70
This is a cool idea. I for one have always loved bugs, in all their various iterations, including the baja bug. I've often thought of the Yaris as the modern day VW bug due to it's simplicity, reliability, dependability and utility. Good luck and post your progress.
MaritimeThread starterWoodstock nb · Feb 3, 2019#71
Ok guys. Still working on this but wife decided this weekend was master bathe reno start so I beat out tearing out tiles, tubs and shit. Spacers came in and I think with 1.5" I shouldnt need to worry about axle or shocks. Ill get little bits done here and there over the next few days and report back.

Sent from my moto e5 play using Tapatalk
MaritimeThread starterWoodstock nb · Feb 4, 2019#72
Originally Posted by justjesus ↑
I have the General tires on my Jeep XJ. So far, I like 'em enough. For my Yaris, I'm running the prior gen of the BFG All Terrains in 195/70-14 (70, I think). They hold up well for daily driver duty.

Sure enough, when looking at my own Off Road Yaris project, I found some Jeep JK front spacers that may work in the rear of the Yaris. Some measurements were taken, and I *think* they could work. I bought them but never put them on to confirm. I'm pretty sure of it, though.






The LSD, plus the xB final drive ratio, is what I was considering for mine. But, unfortunately, I couldn't say "F- the budget" :( The cost of those two items, plus install, was high enough that I took that money and bought a 1996 Jeep Cherokee (XJ).

If you YouTube "off road yaris" mine should be the first hit. You can see where having an LSD would have helped. But in reality, that stuff I was attempting there IS a bit much for a FWD econobox :) I knew this going in! It did much better on regular dirt trails.

I really hope you get this project going!!!! I still go back and forth on mine.

Also, I'm still kind of tinkering with a way to get the rear lifted, without affecting the shocks, or the angle of the rear beam assembly.
Yep, the LSD will be if and when I do an engine swap if the body is still good. I saw your vids on Youtube. Found them after I decided I'd do the Baja and started searching to see if anyone had done it before me. I'm only planning to use it on some old logging roads etc so after seeing what you did, I'm comfortable with the project. I can't find any tires in the 195/75/14 anymore. They are all discontinued, that's why I need to go qith the 27x8.5 14. I hope the 1.5" lift front and back and some fender massage will be enough to fit them without rubbing.

I have just a little bit of fab left on one front lift and I'll be ready to install. If I can swing a couple hours in the evening this week I'll get them installed. The rear lifts came and look promising. If the centers end up to wide, I'll cut those out and the outer cup walls should still keep them in place. Then I will drive it a few times to make sure all is ok noise/vibration wise. If good I'll cover a current wheel tire in foam/cardboard to make it the sized of the new tires and see if it fits in the wells. I'll need to compress the shocks/struts and still turn the wheels to see if they rub. I think I have enough stands and jacks to manage that. I'll post up pics when I do it.
MaritimeThread starterWoodstock nb · Feb 4, 2019#73
Originally Posted by Type-Y ↑
This is a cool idea. I for one have always loved bugs, in all their various iterations, including the baja bug. I've often thought of the Yaris as the modern day VW bug due to it's simplicity, reliability, dependability and utility. Good luck and post your progress.
Me too, I bought the car out of affordability and necessity but really found I love the little thing. I've always loved the Baja bugs and Manx buggies but they cost so much now that I want to do my Yaris up as an Baja inspired byt the VW's.
justjesusOrange County · Feb 4, 2019#74
Originally Posted by myfirstyota ↑
I think you'll have to make rear axle drop brackets if you don't want the angle of the axle affected. I plan on a 3-4" lift and I'm just gonna push that axle down. It will be way too much fab work to make axle mount drop brackets. I took a quick look one day to see if some sort of bolt in drop brackets could be made. Didn't look remotely easy to me.
I had two ideas for that. (1) Where the beam ties into the body, one bolt on each side if I recall. There are actually two bolt holes on either side. Some guys use the upper one once they've lowered the car some. I was thinking using those two bolt holes to make a simple bracket to drop the beam a small amount. (2) was a plate system. One plate per wheel. Sort of like the penguin spacers, but made to "lift" the car by adding ground clearance. I drew it out once, but have moved a couple of times and not sure where that drawing is.


Originally Posted by Type-Y ↑
This is a cool idea. I for one have always loved bugs, in all their various iterations, including the baja bug. I've often thought of the Yaris as the modern day VW bug due to it's simplicity, reliability, dependability and utility. Good luck and post your progress.
Yup. I like those Baja bugs as well. Saw a video or two with a group of them going through some trails near where I live. I watched those videos to see if I thought the Yaris would be able to make it. Haha.. havent tried those yet.

Originally Posted by Maritime ↑
Yep, the LSD will be if and when I do an engine swap if the body is still good. I saw your vids on Youtube. Found them after I decided I'd do the Baja and started searching to see if anyone had done it before me. I'm only planning to use it on some old logging roads etc so after seeing what you did, I'm comfortable with the project. I can't find any tires in the 195/75/14 anymore. They are all discontinued, that's why I need to go qith the 27x8.5 14. I hope the 1.5" lift front and back and some fender massage will be enough to fit them without rubbing.
Thanks for watching! I noticed that size hasn't carried over to the new KO2s. Bummer, for sure. Other tires that I was looking at, and they have more Yaris friendly size options, are dirt rally tires. Not sure how long they'd last on a street driven Yaris, though. I was lucky enough to get the BFGs while they still had them. I believe the Grabbers in 27" size were the next smallest size (not including rally tires).

If you're just looking at some old logging roads, maybe a less aggressive "all terrain" may work.

But then again, the black Overlanding Yaris guy is running 215/75-15 which is about 27.6" tall. Not sure what his "lift" specs are, but it looks like he's having success with them.


Originally Posted by Maritime ↑
I have just a little bit of fab left on one front lift and I'll be ready to install. If I can swing a couple hours in the evening this week I'll get them installed.
Looking forward to your update.
myfirstyotaToronto Canada · Feb 4, 2019#75
Originally Posted by justjesus ↑
I had two ideas for that. (1) Where the beam ties into the body, one bolt on each side if I recall. There are actually two bolt holes on either side. Some guys use the upper one once they've lowered the car some. I was thinking using those two bolt holes to make a simple bracket to drop the beam a small amount.
I also looked at the upper holes to use to mount some type of drop bracket. Now, I didn't spend an hour poking around down there but I didn't think the upper holes were threaded on the inboard side. And because of the way the "frame" is assembled, theres no access to the other side without cutting holes. Please tell me I'm wrong and that the upper holes are threaded on the inboard side (like the lower holes where the axle mounts from factory). If they are... drop brackets would be very feasable. But then I think, you axe some ground clearance by lowering the whole axle...
MaritimeThread starterWoodstock nb · Feb 5, 2019#76
My camber bolts arrived in Maine along with some bumper brackets, my front bumper has been flapping around since I changed out a headlight and found the PO had hot glued the bumper on LOL. I'll grab those this week sometime and the last of what I need to install the lift will be in hand. I'm copying the off the shelf lift from Russia that says no axle relocation required, I hope they are correct but I'll let every one know once I get it installed.
justjesusOrange County · Feb 5, 2019#77
Originally Posted by myfirstyota ↑
Please tell me I'm wrong and that the upper holes are threaded on the inboard side (like the lower holes where the axle mounts from factory). If they are... drop brackets would be very feasable. But then I think, you axe some ground clearance by lowering the whole axle...
You would definitely lose some clearance. 🤷 Seems, there's one trade off or another, right?

The other idea I had, adds maybe about an inch of clearance without affecting anything else.

Anyway, here's the link to using the upper bolt hole. Surely, it is threaded.

Rear suspension
MaritimeThread starterWoodstock nb · Feb 5, 2019#78
Originally Posted by justjesus ↑
You would definitely lose some clearance. 🤷 Seems, there's one trade off or another, right?

The other idea I had, adds maybe about an inch of clearance without affecting anything else.

Anyway, here's the link to using the upper bolt hole. Surely, it is threaded.

Rear suspension
interesting. so the 2 holes could be used with some plate to do the opposite and lower the axle an inch to correct for taller springs and keep travel the same. Very interesting indeed. mind you would lose a little clearance but keep factory set travel.

Edit: you'd definately want to put some shock extensions of the same length as well.
myfirstyotaToronto Canada · Feb 5, 2019#79
Originally Posted by justjesus ↑
You would definitely lose some clearance. 🤷 Seems, there's one trade off or another, right?

The other idea I had, adds maybe about an inch of clearance without affecting anything else.

Anyway, here's the link to using the upper bolt hole. Surely, it is threaded.

Rear suspension
That would appear to be threaded for sure lol
I think the 'penguin spacer bearing relocation plate' would be a good idea to get your lift and maintain axle angle + maintain good ground clearance but the only thing I'd be worried about is lateral force. Maybe some sort of diagonal bracing from the bottom of the bearing mount to somewhere on the axle could be fabricated.

I looked at fabricating my own spacers but came to the realization it's not easy cutting perfect holes in 1/4" and up thick steel plate and abandon the idea.

Side note: I just may be able to get off early enough to pick up my rear spacer bits tonight. I'm having an unforseen issue though and may not be able to fabricate/install the lift for a couple months. Bummer.
MaritimeThread starterWoodstock nb · Feb 5, 2019#80
also looking at parts fiches for the rear you could make a bracket to lower the hubs on the axle instead that would give clearance and lift without touching the springs and shocks at all.
MaritimeThread starterWoodstock nb · Feb 5, 2019#81
Originally Posted by myfirstyota ↑
That would appear to be threaded for sure lol
I think the 'penguin spacer bearing relocation plate' would be a good idea to get your lift and maintain axle angle + maintain good ground clearance but the only thing I'd be worried about is lateral force. Maybe some sort of diagonal bracing from the bottom of the bearing mount to somewhere on the axle could be fabricated.

I looked at fabricating my own spacers but came to the realization it's not easy cutting perfect holes in 1/4" and up thick steel plate and abandon the idea.
Ha I just typed my reply before I saw this. I know a guy stateside with a CNC water jet that could cut anything we could draw up.
myfirstyotaToronto Canada · Feb 5, 2019#82
That's what I had done for my spacer build. Took my sketches to a metal place that does custom cutting. They used a waterjet to cut my pieces. Now if I could only weld lime a pro, they'd look perfect when I'm done lol
MaritimeThread starterWoodstock nb · Feb 5, 2019#83
Originally Posted by myfirstyota ↑
That's what I had done for my spacer build. Took my sketches to a metal place that does custom cutting. They used a waterjet to cut my pieces. Now if I could only weld lime a pro, they'd look perfect when I'm done lol
Cool.
MaritimeThread starterWoodstock nb · Feb 5, 2019#84
ok so get an axle from a wrecked car, then do this:

cut off both:
Picture not included in this copy

flip from one side other, reweld on bottom:

Picture not included in this copy

Or make a bolt on plate:

Picture not included in this copy

3 attachments not included in this copy

MaritimeThread starterWoodstock nb · Feb 5, 2019#85
but then what to do to match on front is the harder one.
thebarberGrand Rapids, MI · Feb 5, 2019#86
scion xb gen1 springs: LIFT IT. LIFT IT GOOD!

Picture not included in this copy
MaritimeThread starterWoodstock nb · Feb 5, 2019#87
Ha, ok. I really want to put the lift I have made in tonight because its +7C today here. I wonder if the wife will let me out of bathroom duty to do it?
myfirstyotaToronto Canada · Feb 5, 2019#88
Maritime, I don't think that rear cut and weld axle idea will work. Not sure how your axle is built but mine doesn't look like that at all. The bearing mount on the ends of the axle are welded around the circumference of the mount. The axle is like an oval pipe on the ends. On my car, the bearing mount is fully welded around the outside to the pipe that makes up the axle. It's not like pictured in post 84.

Side note:
Picture not included in this copy
See where this is going?

Maritime, I'll stop polluting your thread now lol
MaritimeThread starterWoodstock nb · Feb 5, 2019#89
I see ;D

Sent from my moto e5 play using Tapatalk
MaritimeThread starterWoodstock nb · Feb 6, 2019#90
Pulled the thule out of storage. Going to need a trim width wise and need to sort bolts but it will.work great and at 0$ budget friendly.
hotracer_05Rowlett, TX · Feb 6, 2019#91
subd, thought about lifting mine as well...but ive gotten used to cornering pretty hard in it lol.
myfirstyotaToronto Canada · Feb 6, 2019#92
Originally Posted by hotracer_05 ↑
subd, thought about lifting mine as well...but ive gotten used to cornering pretty hard in it lol.
Use xd springs. Still corners ok with the trd rear sway bar and 70 series tires
MaritimeThread starterWoodstock nb · Feb 7, 2019#93
dug my rack out of storage, going to need to be cut down a bit and I need to finalize how I will bolt it on. Can't find just the bolts online from Thule, have to buy the whole towers so I need to check Mcmaster or fastenal etc. to find something that will work. Also got the second front lift closer to finished, I may actually get it installed this weekend if the bathroom works goes fast enough. Ordered a set of threaded inserts to mount this and they will arrive by Monday next week. I'll get it set and ready to go on the weekend then drill and mount next week.

1 attachment not included in this copy

MaritimeThread starterWoodstock nb · Feb 14, 2019#94
Project isn't dead, just slowed. I got 20 min to finish the second front lift. So they are ready to install and after yesterdays 2' of snow and the floor dragging I'd like it in there now. I also got the riv-nuts in from amazon so I can mount the rack. Hopefully this weekend, the bathroom is about half done, so when I get to laying tile, I'll have wait time between laying and grouting that I hope to get the lifts in front and back and report on how they work. As long as the honey do list doesn't get added too that is.
06YarisRSFredericton, New Brunswick, Canada · Feb 15, 2019#95
Originally Posted by Maritime ↑
Project isn't dead, just slowed. I got 20 min to finish the second front lift. So they are ready to install and after yesterdays 2' of snow and the floor dragging I'd like it in there now. I also got the riv-nuts in from amazon so I can mount the rack. Hopefully this weekend, the bathroom is about half done, so when I get to laying tile, I'll have wait time between laying and grouting that I hope to get the lifts in front and back and report on how they work. As long as the honey do list doesn't get added too that is.
🎉 Looking forward to the progress.
hotracer_05Rowlett, TX · Feb 15, 2019#96
Originally Posted by myfirstyota ↑
Use xd springs. Still corners ok with the trd rear sway bar and 70 series tires
What year range XD should I keep an eye out for? I have a 3rd gen 2012 3 door
myfirstyotaToronto Canada · Feb 15, 2019#97
Any. I don't think the was much difference between the years suspension wise.
MaritimeThread starterWoodstock nb · Feb 26, 2019#98
Well. Still no time to install the lift, this is the reason but getting closer to finished. I am not a fast as I was prior to a bad Motorcycle crash involving a deer slamming into me from the side and ruining my left leg and hip. Doing tile at 44 and being a gimp this is taking 2-3 X longer than it would have. But once done I get garage time again!

1 attachment not included in this copy

LeegamerAshland, VA · Feb 26, 2019#99
Tile looks good! I spent the weekend doing tile in my kitchen.
6x36 pieces on a 55 year old floor are a pain in the rear.
MaritimeThread starterWoodstock nb · Feb 26, 2019#100
Originally Posted by Leegamer ↑
Tile looks good! I spent the weekend doing tile in my kitchen.
6x36 pieces on a 55 year old floor are a pain in the rear.
I bet, that's 18x18 travertine stone. floor was nice and level for me, 1" boards with 1/2" ply on top, but the tiles were different thickness sometimes being natural stone. having to lift one up to re-level by either adding or removing thinset sucks LOL. Took me from Friday evening till end of day Sunday to lay the 110 square feet. I was beat out.