Yarisworld Archive

First US 2ZR-FE Yaris swap gains exposure

193 posts · 77,985 views · page 3 of 4

Replies continued

CrankyOldManWest Michigan · Dec 14, 2015#101
Originally Posted by Jason@SportsCar ↑
The speedo hole was there on the 2012, just capped off, but I don't recall the plastic speedo driven gear being on the diff carrier.
Hmm. I guess it wouldn't serve any purpose, since the bearing seats against the diff carrier itself, but it's still shown in the xD parts diagrams.
ArmstrongRacingThread starterSan Diego · Dec 15, 2015#102
Originally Posted by Jason@SportsCar ↑
2012+ Yaris does not have a speed sensor on the trans either, pulls it from the ABS tone ring.
This would make the 2zr swap so much easier...are the 2012+ 1nz's using a micro MAF sensor too?....that would be a direct swap with no wiring changes!
LTHatchNewark NJ · Dec 15, 2015#103
How do you go about checking if its a micro maf? I'll take a look at mine.
Jason@SportsCarDebary, FL · Dec 15, 2015#104
Originally Posted by ArmstrongRacing ↑
This would make the 2zr swap so much easier...are the 2012+ 1nz's using a micro MAF sensor too?....that would be a direct swap with no wiring changes!
MAF sensor is the same from 2007-2015. The thing that could hurt your swap on a 2012+ is the ECU and harness plugs, they are different. When we built the 2015 it was easier to swap the entire harness from the 2007 versus rewiring. If you can use the Yaris ECU and engine harness on the 2ZR you should be able to put it in any year car.
ArmstrongRacingThread starterSan Diego · Dec 15, 2015#105
Interesting. I dont know that a pre-12' chassis harness would work on a 12+ though...its .not likely due to all of the interior changes. If someone becomes interested, Ill need to get a copy of the 12'+ wiring diagrams to come up with a solution.
maralieuscool california · Dec 20, 2015#106
Originally Posted by ArmstrongRacing ↑
Thanks for the support!

Because this project was a auto > manual trans conversion also, we used the Xd manual trans and axles. Ive heard from many sources that the 1nz and 2zr bell housings are compatible, but I wont have a final answer untill I source another 2zr for my personal car.

The ECU came from the Xd also.
Wow this is great news considering my 07 will be ready for a rebuild and new tranny on the next couple years, I can plan towards this instead! Great work and thanks for finding such an easy swap!
ArmstrongRacingThread starterSan Diego · Dec 20, 2015#107
Originally Posted by CrankyOldMan ↑
Yes, if you get the xD gearbox, you need the xD axles. RagNaCat discovered that the differential is the larger one that's similar to the other 1.8L family. Not sure if they're direct swap from a Corolla or Matrix on the axle side, but the Celica and Matrix final drive ring gears go on the xD diff (and not the Yaris/xA/xB).
I just did a bit of reading and I "think" what I've found is that the Yaris transmission(C54?) AND the XD transmission(C50?) have the same gear ratios, the only difference is the final drive. The XD has a 3.94 while the Yaris has a 3.72. So in theory the XD gearbox will give you a bit more acceleration.

I'm still unsure if the Yaris Tsport has a 5 or 6 speed though, the Internet has conflicting information...
CrankyOldManWest Michigan · Dec 20, 2015#108
Originally Posted by ArmstrongRacing ↑
I just did a bit of reading and I "think" what I've found is that the Yaris transmission(C54?) AND the XD transmission(C50?) have the same gear ratios, the only difference is the final drive. The XD has a 3.94 while the Yaris has a 3.72. So in theory the XD gearbox will give you a bit more acceleration.

I'm still unsure if the Yaris Tsport has a 5 or 6 speed though, the Internet has conflicting information...
The US Yaris has the C50 as well, but uses a different differential carrier. Other than that, the gears themselves should be the same (part numbers and everything). There are some global variants of the Yaris that use a C53 or C54 gearbox, but they should have the same bell housing bolt pattern and mount bosses.🙂

There's a few variants that use the EC67 gearbox, but it's very different from the C50. The slave cylinder is directly on the throwout bearing, and the hydraulic hard lines are different. The case is also 2-piece instead of 3. Here's an eBay UK listing of a similar gearbox.
ArmstrongRacingThread starterSan Diego · Dec 21, 2015#109
So what would be the ideal transmission for those interested in a 2zr swap AND a auto>manual trans swap? Can we do a pros VS cons on the available transmission choices?
CrankyOldManWest Michigan · Dec 21, 2015#110
Originally Posted by ArmstrongRacing ↑
So what would be the ideal transmission for those interested in a 2zr swap AND a auto>manual trans swap? Can we do a pros VS cons on the available transmission choices?
Sounds good to me! Perhaps include a "bravery" rating as well, since some options would include non-trivial modifications to the drivetrain?

Stock Yaris C50 - Bravery: Sir Robin
Pro
  • Keep stock axles and mounts
  • Direct fit
  • Final drive is taller: higher top end speed in each gear
Con
  • May be limited in power handling above 150 whp (axles)
  • Final drive is taller: less torque/acceleration in each gear

Stock xD C50 - Bravery: Sir Galahad
Pro
  • Keep stock axles and mounts from xD
  • Direct fit
  • Final drive is shorter: better acceleration in each gear
Con
  • Must use axles from xD
  • Final drive is shorter: lower top end speed in each gear

Custom gearbox internals - Bravery: Black Knight
Pro
  • Get the ratios you want for almost every gear
  • Get the final drive ratio that works for your application
  • Excellent opportunity to add limited slip
Con
  • Requires mechanical knowhow and proper tools (the service manual is one of them!)
  • Can be VERY expensive to source new OEM parts
  • Can be LUDICROUSLY expensive to source aftermarket parts
  • Will require extended downtime to build the gearbox, can be worked around by getting a donor gearbox and building it before the swap
ArmstrongRacingThread starterSan Diego · Dec 21, 2015#111
^that is awesome! Thank you!

Im also starting to contact the Lotus guys to see how the 2zr handles track abuse and if it needs cooling upgrades
3cyltrboOttawa · Dec 29, 2015#112
Originally Posted by ArmstrongRacing ↑
^that is awesome! Thank you!

Im also starting to contact the Lotus guys to see how the 2zr handles track abuse and if it needs cooling upgrades
Like so many other people that have posted, I'd be up for getting information on the order of a DIY.......

I'm in the frozen north, land of Igloos and Universal Health Care............so having a paid swap done in the USA is out of the question.

This seems a little bit easier than a K20 swap

Will
ArmstrongRacingThread starterSan Diego · Dec 30, 2015#113
Originally Posted by 3cyltrbo ↑
Like so many other people that have posted, I'd be up for getting information on the order of a DIY
UPDATE: Ive completed my move to San Diego and have started searching for 2zrfe's. Ive found a few at dismantlers out of Corollas for $850-1000....but not complete engines. I will be purchasing one of the longblocks to test fit with a Yaris clutch and transmissions asap.
CoryMWhite Rock BC · Jan 2, 2016#114
I've been watching this post from the start and have been wondering if there is a more common (AKA cheaper) LSD option for the XD? Or another trans that bolts in?

Also, good job on the swap!
CrankyOldManWest Michigan · Jan 2, 2016#115
Originally Posted by CoryM ↑
I've been watching this post from the start and have been wondering if there is a more common (AKA cheaper) LSD option for the XD? Or another trans that bolts in?
Generally, no. The "cheapest" option is a Phantom Grip, which still runs a few hundred dollars and requires complete disassembly of the stock differential to install. There was an OBX-made torsen style that was hit or miss for being a grenade for around US$700 iirc, but I haven't looked for them recently. You might be able to find an OEM LSD in a junkyard if the stars all align for you, but I use US$1000 as the benchmark for adding limited slip of any kind that isn't going to be a gamble down the road.
ArmstrongRacingThread starterSan Diego · Jan 2, 2016#116
^What oem lsd are you referring to?
CoryMWhite Rock BC · Jan 2, 2016#117
Originally Posted by CrankyOldMan ↑
Generally, no. The "cheapest" option is a Phantom Grip, which still runs a few hundred dollars and requires complete disassembly of the stock differential to install. There was an OBX-made torsen style that was hit or miss for being a grenade for around US$700 iirc, but I haven't looked for them recently. You might be able to find an OEM LSD in a junkyard if the stars all align for you, but I use US$1000 as the benchmark for adding limited slip of any kind that isn't going to be a gamble down the road.
Thanks for the reply. Yeah, that's the price range I was finding as well. I just can't justify spending that on my Yaris even though it would make a world of difference. If I could do an easy motor swap, get more power/torque and LSD I'd be all over that though. As is, I give you guys credit for the work you've been doing; trying new things is what hot-rodding is all about.

Cheers
ArmstrongRacingThread starterSan Diego · Jan 3, 2016#118
Originally Posted by CoryM ↑
... If I could do an easy motor swap, get more power/torque and LSD I'd be all over that though.
This is exactly my plan with my personal 2zr swap. I have a spare Yaris trans I will upgrade with the Xb final drive and a LSD....given That the yaris trans works with the 2zr.
beakerconyers ga · Jan 3, 2016#119
For what it's worth:

On toyodiy.com

2008 Toyota Yaris NCP91 with a 1NZFE 1.5 Liter engine, uses a C50 manual trans part # 30300-52360.

2008 Scion XD ZSP110 with a 2ZRFE 1.8 Liter engine, uses a C50 manual trans part # 30300-52360.

Same trans, so my guess would be that a Yaris trans will bolt to the 2ZRFE engine, or at least in this case.

I've got a 2007 Yaris with an auto, and if I did this swap, would go consider going manual, but the manual trans part number for my year is a 30300-52510. I bet the difference has to do with VSS sensor vs. getting speed off of ABS, as my car doesn't have ABS.

Checked the auto trans part #s, they are different from a Yaris and a XD.

I'm just wondering if you can run the Yaris computer with the 2ZRFE, or if you have to swap out with an XD computer?
ArmstrongRacingThread starterSan Diego · Jan 3, 2016#120
Wow...thats more evidence suggesting compatibility. Thank you.

Anytime you swap Toyota engines you are required to swap in that corresponding ecm. And yes the 2zrfe uses a different auto trans, I haven't looked into why though
fnkngrvIn The Hotbox · Jan 3, 2016#121
If someone was in the market for a used Yaris and they did it smartly depending on how much equity they could have in the purchase it would be smart to roll the swap right into the note ;-)

Sent from my XT1575 using Tapatalk
3cyltrboOttawa · Jan 4, 2016#122
sooooo........................................why aren't we also talking about the 2Litre- 3ZR-FE ?

Is it because its not as readily available in North America?

Does anyone (CTScott???) know if it is dimensionally the same as the 2ZR ? (ie:, is it just a bored and stroked 2ZR?)

Either way, I'm still anxious for more information because I was thinking about some other "next level" mods for my 1nz-fe, and it seems more cost effective to put that investment into a swap.

Will
ArmstrongRacingThread starterSan Diego · Jan 4, 2016#123
Originally Posted by 3cyltrbo ↑
sooooo........................................why aren't we also talking about the 2Litre- 3ZR-FE ?

Is it because its not as readily available in North America?
We briefly discussed the 3zr, and yes it will probably work but like you said...its not available in the US. The 2zrfae just now showed up here and it was developed in 2010!
3cyltrboOttawa · Jan 4, 2016#124
Originally Posted by ArmstrongRacing ↑
We briefly discussed the 3zr, and yes it will probably work but like you said...its not available in the US. The 2zrfae just now showed up here and it was developed in 2010!
If I had some assurance that the 2 litre was the same (externally) as the 1.8, and if I knew that it would bolt up to the 1nzfe tranny (like its looking the 1.8 will) than I would almost go through the effort of importing the 2litre (I know a guy 😉 ) ......................................

Will
Bluevitz-rsOshawa, Ontario, Canada · Jan 4, 2016#125
Originally Posted by 3cyltrbo ↑
If I had some assurance that the 2 litre was the same (externally) as the 1.8, and if I knew that it would bolt up to the 1nzfe tranny (like its looking the 1.8 will) than I would almost go through the effort of importing the 2litre (I know a guy 😉 ) ......................................

Will
1ZR, 2ZR and 3ZR are more than likely the same as 1NZ and 2NZ. They're all different displacement but otherwise use the same parts. Unlike the 1ZZ and 2ZZ in which are totally different engines.
ArmstrongRacingThread starterSan Diego · Jan 4, 2016#126
I don't believe the 3zr at 150hp is worth the additional effort, and it would not be a legal option. The 2zr has n/a bolt-on potential to 150hp, or you can boost it like Lotus does
3cyltrboOttawa · Jan 4, 2016#127
Originally Posted by ArmstrongRacing ↑
I don't believe the 3zr at 150hp is worth the additional effort, and it would not be a legal option.
Up here in the land of Igloos / clean water and Universal Health care, "Legal" engine swap is not really on our Radar.

All we have to do for "Emissions Testing" is to plug a scan tool into the OBD port and check for CEL codes. Thats it.

They don't even run sniff tests anymore (for tail-pipe emissions).

I literally have one friend of mine that has a Stand-Alone ECU that runs his car, but just for shits and giggles he keeps a bogus ecu powered up and "properly" setup in the car (Connected to the OBD port) just so that when he has to get a "DriveClean test" (only once every two years), he just takes it to the testing facility , they connect their scan tool - they see that there is an ECU present.. that isn't throwing codes and thats it.

I could frankly install just about any motor I wanted as long as it gave a reading through the OBD port and it didn't show a code DURING the test.


Now back to our regularly scheduled engine swap discussion.
3cyltrboOttawa · Jan 4, 2016#128
Originally Posted by ArmstrongRacing ↑
The 2zr has n/a bolt-on potential to 150hp, or you can boost it like Lotus does
My thinking with the 2 litre, is the extra torque and the effect that mods would have.

I agree that the 1.8 can be modded (NA), but I'm just thinking that there is no replacement for displacement and the 2 litre would have some nice torque.

?
3cyltrboOttawa · Jan 4, 2016#129
Originally Posted by Bluevitz-rs ↑
1ZR, 2ZR and 3ZR are more than likely the same as 1NZ and 2NZ. They're all different displacement but otherwise use the same parts. Unlike the 1ZZ and 2ZZ in which are totally different engines.
thank you, this is reassuring (and I know that you know your stuff)

Will
fnkngrvIn The Hotbox · Jan 4, 2016#130
Let's stay on track with the OP. His whole goal is to have a legal way in his state to be able to perform a 2zr swap. The 3zr is our of scope and most likely will never be addressed by folks here as isn't worth the time, money, or efforts for the minor bump in hp/tq over the 2zr.

Sent from m-o-b-i-l-e
ArmstrongRacingThread starterSan Diego · Jan 5, 2016#132
I understand that a 2.0L has that extra displacement, and I would welcome anyone to try the 3zr swap just to be the first. Its a good idea, just not practical like the 2zr is.

...on another note, all of you should pay close attention to this thread. This swap just got kicked into high gear....El Nino floods resulted in the premature death of my 1NZ today...
ilikericesavannah, ga · Jan 6, 2016#133
Originally Posted by ArmstrongRacing ↑
I understand that a 2.0L has that extra displacement, and I would welcome anyone to try the 3zr swap just to be the first. Its a good idea, just not practical like the 2zr is.

...on another note, all of you should pay close attention to this thread. This swap just got kicked into high gear....El Nino floods resulted in the premature death of my 1NZ today...
Noooo.... Yaaaaaay... Noooo... Yaaaaay....

I have mixed feelings about that
ArmstrongRacingThread starterSan Diego · Jan 6, 2016#134
Me too.....I guess I had a good run though. 184,000 miles with track days, mountain runs, roadtrips, and autocross. Im going to call my insurance company today and see if flood related damage is covered.
3cyltrboOttawa · Jan 6, 2016#135
Originally Posted by ArmstrongRacing ↑
Me too.....I guess I had a good run though. 184,000 miles with track days, mountain runs, roadtrips, and autocross. Im going to call my insurance company today and see if flood related damage is covered.
Dude

Sorry to hear about your 1nzfe (and potentially your car)

Will
ern-dizCA all day · Jan 6, 2016#136
Originally Posted by ArmstrongRacing ↑
I understand that a 2.0L has that extra displacement, and I would welcome anyone to try the 3zr swap just to be the first. Its a good idea, just not practical like the 2zr is.

...on another note, all of you should pay close attention to this thread. This swap just got kicked into high gear....El Nino floods resulted in the premature death of my 1NZ today...
Ugh, what a bummer. Hope things work out for the best.

Stay safe out there everyone.
ArmstrongRacingThread starterSan Diego · Jan 6, 2016#137
I have found a 2zr out of a 2013 Corolla with 34k. Once the insurance company does their thing and I get a check....the swap begins....hopefully in the next few days.
fredovvtiSabana Grande, PR · Jan 7, 2016#138
Pleaseeeeee!!! A DIY!!!

Sorry for the lost
Focus_Sh1ftNew Jersey · Jan 7, 2016#139
Sorry to hear about the flood damage. 🤷

Am I right to assume you're not going to be using the 1NZ transmission now?
ArmstrongRacingThread starterSan Diego · Jan 7, 2016#140
I have a spare transmission, and I dont think the trans is damaged. Ill just do a fluid change.
3cyltrboOttawa · Jan 7, 2016#141
have we talked about the Scion IM 6spd and if it would fit the 2ZR?
Bluevitz-rsOshawa, Ontario, Canada · Jan 7, 2016#142
Originally Posted by 3cyltrbo ↑
have we talked about the Scion IM 6spd and if it would fit the 2ZR?
the question should be would the 6spd fit the Yaris. The iM uses a 2ZR to begin with.
ArmstrongRacingThread starterSan Diego · Jan 7, 2016#143
Originally Posted by 3cyltrbo ↑
have we talked about the Scion IM 6spd and if it would fit the 2ZR?
We have not, but I believe its the same 6spd in the newer corolla....witch has a 2zr also. Im pretty sure its compatible
3cyltrboOttawa · Jan 7, 2016#144
sorry I got lost in the details, I thought the 2zr-fae was different than the 2zr-fe?
ArmstrongRacingThread starterSan Diego · Jan 8, 2016#145
The only significant difference is they increased compression from 10:1 to 10.5:1(Edit: and Valvematic). Otherwise they are almost identical
Bluevitz-rsOshawa, Ontario, Canada · Jan 8, 2016#146
Originally Posted by ArmstrongRacing ↑
The only significant difference is they increased compression from 10:1 to 10.5:1. Otherwise they are almost identical
And the MAJOR fact that it uses a different head and valve system to control RPM not a throttle body.
Bluevitz-rsOshawa, Ontario, Canada · Jan 8, 2016#147
Originally Posted by 3cyltrbo ↑
sorry I got lost in the details, I thought the 2zr-fae was different than the 2zr-fe?
The blocks should be nearly identical, it's the head and valve train that differ.
ArmstrongRacingThread starterSan Diego · Jan 8, 2016#148
Originally Posted by Bluevitz-rs ↑
And the MAJOR fact that it uses a different head and valve system to control RPM not a throttle body.
.... the question was about transmission compatibility haha....but thanks for the info!
ArmstrongRacingThread starterSan Diego · Jan 8, 2016#149
Started disassembly today

1 attachment not included in this copy

Bluevitz-rsOshawa, Ontario, Canada · Jan 8, 2016#150
Is the car stuck in a lot right now, or is this where you work...??