Yarisworld Archive

tooter's next manifold adventure...

151 posts · 75,762 views · page 2 of 4

Replies continued

tooterThread starterLos Angeles · Feb 3, 2014#51
It's dyno day. 🙂

I'm waiting for the call...
cali yarisCanoga Park, CA · Feb 3, 2014#52
Can't wait to see.
GolddeenohColumbia, SC · Feb 3, 2014#53
how about now?

:D
tooterThread starterLos Angeles · Feb 3, 2014#54
Ok. Just got back from Harry's shop...

(ta da 🙂 )

Red: no spacer
Blue: with the tooter I.V spacer

Picture not included in this copy



Both runs were done with the same short ram intake, the same air filter, the same stock plastic intake manifold, the same stock throttle body, the same header, and the same axle back exhaust.

The tooter I.V intake manifold spacer was the only change.

This is similar to the results I got with my Tacoma. The I.V spacer lowered the torque peak from 4,100 rpm down to 3,650 rpm as well as fattening up the torque curve a little. Not too bad for just a simple bolt on part. 🙂

Just for context, the bone stock torque peak is 4,400 rpm, so the intake, the 4-2-1 header, and the Magnaflow exhaust had already lowered it by 300 rpm. The spacer lowered the peak by another 450 rpm for a total of 750 rpm.

Greg
WeeYariGeorgetown, Ontario, Canada · Feb 3, 2014#55
Got a selling price set yet? I couldn't spot mention of $$s in this thread.
GolddeenohColumbia, SC · Feb 3, 2014#56
nice .65HP and 3.2lbft torque. now if you can get the production price and kits together. 😉
tooterThread starterLos Angeles · Feb 3, 2014#57
Originally Posted by WeeYari ↑
Got a selling price set yet? I couldn't spot mention of $$s in this thread.
Not yet... I just ordered a dozen blocks for the first production run and the shop hasn't gotten back to me yet on the material cost.

From the original concept on November 29th to a dyno tested prototype took only a little over 3 months and that was with the holidays. So if all goes well, I should have finished products ready to ship in another month for a total elapsed time of 4 months from virtual concept to the reality of a finished product ready to sell.

This is the advantage of a microbusiness where just one person calls all the shots. 🙂


Greg
tooterThread starterLos Angeles · Feb 3, 2014#58
Originally Posted by Golddeenoh ↑
nice .65HP and 3.2lbft torque. now if you can get the production price and kits together. 😉
I'm working on it right now... 😛
The negligible horsepower increase is only incidental as this was not designed to be a top end high performance accessory. The purpose of this spacer is to make regular daily driving easier because the engine doesn't have to work as hard at low rpms.

And the increased torque peak really isn't all that much either. Most all of the advantage comes from shifting the whole torque curve down lower in the rpm range. So as the two torque curves are climbing, the spacer curve remains above of the baseline curve. This spreads the torque increase over a larger rpm operating range. 🙂

This mod is for just regular low rpm daily driving.

Greg
malibuguyWestminster, MD · Feb 3, 2014#59
Anyway to overlay this with a tooter dyno as well?

Btw madness on the midrange gains!
tooterThread starterLos Angeles · Feb 3, 2014#60
Originally Posted by malibuguy ↑
Anyway to overlay this with a tooter dyno as well?

Btw madness on the midrange gains!
That's a great idea. 🙂 I'll see if Harry can do it. I need to talk to him about the chart anyways as the peak numbers don't match up with the line on the chart, so one or the other isn't right.

The tooter manifold with the larger throttle body makes 111 horsepower, so it's graph will be a lot stronger at the top.

It would be run 16 with the plain tooter intake manifold and the 1ZZ throttle body...

Picture not included in this copy
...and run 23 with the stock manifold and the tooter I.V spacer.

Picture not included in this copy

Longer intake runners making more torque is a sound mechanical principle that worked out really well on my Tacoma, so I figured, heck, why not for the Yaris too? 😉

Greg
7:34pmBritish Columbia · Feb 4, 2014#61
If you have the resources, you should experiment with different spacer sizes to find the optimum length. I'd be curious to see the different outcomes.

And then run them all on the dyno, on the same day so there is no discrepancy between the variables.
Kaotic LazagnaCentral Valley, CA · Feb 4, 2014#62
I like the bump in torque and where the bumps are in the band.
Silver StreakMassachusetts · Feb 4, 2014#63
I'm very excited about this spacer. Most of my driving is done in this rpm range, and will make the 1.5's acceptable torque even better.
tooterThread starterLos Angeles · Feb 4, 2014#64
There's something that doesn't show up in the dyno runs, and that's partial throttle performance at extremely low rpms right down to idle and even below. This is because the dyno runs done by mashing the gas pedal to the floor at 1,300 rpm in third gear. This is an extreme condition that is not encountered in normal driving. Very low off idle torque is exceptionally good especially when taking off from a stop with a manual transmission. On level ground even if you let out the clutch and forget to use the throttle, the engine doesn't die. Instead the car slowly moves forward without any bucking.

Greg
WeeYariGeorgetown, Ontario, Canada · Feb 4, 2014#65
Originally Posted by tooter ↑
Not yet... I just ordered a dozen blocks for the first production run and the shop hasn't gotten back to me yet on the material cost.
In the meantime, can you source a shipping quote to L0P 1K0 Ontario, Canada? Preferably USPS.
marcustoronto, canada · Feb 4, 2014#66
sweeet!
tooterThread starterLos Angeles · Feb 4, 2014#67
Originally Posted by 7:34pm ↑
If you have the resources, you should experiment with different spacer sizes to find the optimum length. I'd be curious to see the different outcomes.

And then run them all on the dyno, on the same day so there is no discrepancy between the variables.
Sorry, I don't have the time or the resources. 😳

This is just a hobby I do on the side in my free time off of work. Dyno time gets really expensive when your car is on the machine and you're trying to swap out parts. Adding the cost for new CNC programming would make it unpractical to make a bunch of different sizes. Anyways you can simply extrapolate the difference as a one inch spacer would make half the torque as a two inch.

I picked 2 inches because that is the thickest spacer which will work without interfering with the engine peripherals like the oil dipstick tube. The two inch simply drops into place like it belongs there.

Picture not included in this copy

Other intake manifold spacers sold like this one for a Toyota Tacoma V6 are usually only a half inch thick...

Picture not included in this copy

...while the tooter I.V is like stacking up FOUR of them. 🙂

Picture not included in this copy



Greg
07stlYarisSTL · Feb 4, 2014#68
How about a 1/2" spacer for between the Blitz and the head? I haven't had a heat soak situation yet but this might be a pre-emptive strike. If possible, how much and how soon?
WeeYariGeorgetown, Ontario, Canada · Feb 4, 2014#69
^^

Originally Posted by tooter ↑
Sorry, I don't have the time or the resources. 😳
tooterThread starterLos Angeles · Feb 4, 2014#70
Originally Posted by 07stlYaris ↑
How about a 1/2" spacer for between the Blitz and the head? I haven't had a heat soak situation yet but this might be a pre-emptive strike. If possible, how much and how soon?
They're already available. You can get them from Garm at MicroImage.com. Two of them make about a half inch. 👍

Picture not included in this copy
tooterThread starterLos Angeles · Feb 4, 2014#71
Originally Posted by WeeYari ↑
Got a selling price set yet? I couldn't spot mention of $$s in this thread.
When they're available they'll be offered for sale at $265 including shipping. The shop still has tooter II.VII Tacoma spacers in the works so the I.V's will be machined once they're completed.

Picture not included in this copy

Greg
Silver StreakMassachusetts · Feb 4, 2014#72
Bummer great mod, but out of my price range right now. I'm curious Tooter, what do you think the spacer would yield on a bone stock Yaris?
ViperoniBrampton, ON · Feb 4, 2014#73
For just an intake manifold spacer, these are awesome gains!
tooterThread starterLos Angeles · Feb 4, 2014#74
Originally Posted by Silver Streak ↑
Bummer great mod, but out of my price range right now. I'm curious Tooter, what do you think the spacer would yield on a bone stock Yaris?
From the dyno tests I've seen, a stock Yaris makes about 91 horsepower and 91 foot pounds of torque at the wheels.

So extrapolating the results I got with my engine, the spacer would only make about 92 horsepower and 94 foot pounds of torque.

Note on the graph that the peak values for both hardly go up at all with the spacer. The biggest difference is in the profile of the torque curve, and that the torque peak is reached 450 rpm sooner.
tooterThread starterLos Angeles · Feb 4, 2014#75
Originally Posted by Viperoni ↑
For just an intake manifold spacer, these are awesome gains!
It's not so much the peak gains themselves as they're actually quite small, it's more how they're distributed in particular the torque. I was really happy with the results on my Tacoma, and the Yaris turned out even better than the truck. 🙂

Greg
tooterThread starterLos Angeles · Feb 5, 2014#76
Originally Posted by WeeYari ↑
In the meantime, can you source a shipping quote to L0P 1K0 Ontario, Canada? Preferably USPS.
Sure. The spacer and hardware will fit into a USPS international medium flat rate box which is $42.25. That same box ships domestically for $12.35, so the additional shipping cost to Canada would be $30.

Greg
marcustoronto, canada · Feb 5, 2014#77
tooter just curious if theres an issue with the stock airfilter box moving 2 inch forward?
WeeYariGeorgetown, Ontario, Canada · Feb 5, 2014#78
Sorry Greg, that came in higher than I thought it would. I do applaud the results of your insatiable curiosity.

Look forward to seeing what you dream up next.
tooterThread starterLos Angeles · Feb 5, 2014#79
Originally Posted by marcus ↑
tooter just curious if theres an issue with the stock airfilter box moving 2 inch forward?
I don't know because I run a short ram that just moves along with wherever stock throttle body is. The stock rubber hose is pretty flexible, but I don't know if it will offset 2 inches.

I do know the lines that circulate coolant through the base of the throttle body will be too short. So I simply connected them to each other using a short scrap of tubing as a coupling.

Greg
cali yarisCanoga Park, CA · Feb 5, 2014#80
The spacer and hardware will fit into a USPS international medium flat rate box which is $42.25. T
No need for the extra expense of a flat rate box. 2 pounds (guessing) to Canada is $28.
tooterThread starterLos Angeles · Feb 5, 2014#81
Thanks Garm. 🙂

Then it's $16 extra to ship to Canada.

I posted a thread in the For Sale section where anyone can add their name if they're interested.


Greg
marcustoronto, canada · Feb 5, 2014#82
i was hoping itll be under $200 shipped.. but it is definetely something to think about..
BEEFnorth carolina · Feb 5, 2014#83
My thing was that tooter usually makes short runs of products. I was thinking of doing this later on but the issue is they may not be available so I am going ahead and biting the bullet.

I guess that is the thing with specialized products. I joined after the Piggies short throw shifter was long gone so I had to wait for garm to come out with his. Waiting about killed me so I am a little more apt to jump on something if I know quantity is limited.
tooterThread starterLos Angeles · Feb 6, 2014#84
Originally Posted by BEEF ↑
My thing was that tooter usually makes short runs of products. I was thinking of doing this later on but the issue is they may not be available so I am going ahead and biting the bullet.

I guess that is the thing with specialized products. I joined after the Piggies short throw shifter was long gone so I had to wait for garm to come out with his. Waiting about killed me so I am a little more apt to jump on something if I know quantity is limited.
Demand for a product like this is slight because the market is paper thin and quickly saturated. So I only make short runs. I'm just happy to have the prototypes for my own use, and sell a few more to cover all of the design, prototype machining, dyno testing, raw materials, production, mounting hardware and gaskets, and shipping costs. So far I've been able to break even on both the tooter intake manifolds and the tooter II.VII spacers. So now I'm recycling the same startup money into the tooter I.V spacer project. 🙂


Greg
ezhacker1San Francisco · Feb 6, 2014#85
Originally Posted by tooter ↑

I do know the lines that circulate coolant through the base of the throttle body will be too short. So I simply connected them to each other using a short scrap of tubing as a coupling.

Greg
Bypassing the coolant flow through the throttle body, probably marginal lower intake air temp.

Guess i should get this spacer rather than a exhaust header, more practical to have the same torque at lower rpms (everyday driving RPM).

My guess is Id save a little gas by being able to be in 5th doing 25mph in Residential area. Also probably can stay in 5th and still have passing torque on freeway.

**So this spacer moves the same profile curve to the left. And the tooter manifold with 1ZZ TB just gives higher max numbers. Between those two, the spacer is better for a normal day to day use car?
tooterThread starterLos Angeles · Feb 6, 2014#86
Originally Posted by marcus ↑
i was hoping itll be under $200 shipped.. but it is definetely something to think about..

Sorry man... it's extremely expensive to design, test, and manufacture small amounts of highly specialized parts. So everyone gets to weigh the cost to benefit ratio and decides for themselves.


Greg
marcustoronto, canada · Feb 6, 2014#87
Originally Posted by tooter ↑
Sorry man... it's extremely expensive to design, test, and manufacture small amounts of highly specialized parts. So everyone gets to weigh the cost to benefit ratio and decides for themselves.


Greg
dont apologize ..no worries i kinna understand the whole process..
tooterThread starterLos Angeles · Feb 6, 2014#88
Originally Posted by ezhacker1 ↑
Bypassing the coolant flow through the throttle body, probably marginal lower intake air temp.

Guess i should get this spacer rather than a exhaust header, more practical to have the same torque at lower rpms (everyday driving RPM).
I don't know... that TRD header in the For Sale section is a really good deal . And from looking at it's design with the slightly longer runners, it would also add bottom end torque. I just don't know how much.

My guess is Id save a little gas by being able to be in 4th doing 25mph in Residential area. Also probably can stay in 5th and still have passing torque on freeway.
The spacer makes it easy to short shift at 2,000 rpm around town without lugging the engine. It's also really easy to take off from a standing start without a lot of clutch slipping or revs. It generally makes normal everyday driving more pleasant.

Now that the ECU has settled in and the car is all gassed up, I'm ready to log some mileage readings. I'll let you know the results, for better or for worse.


**So this spacer moves the same profile curve to the left. And the tooter manifold with 1ZZ TB just gives higher max numbers. Between those two, the spacer is better for a normal day to day use car?
For regular transportation driving... the tooter I.V spacer beats the hell out of the tooter manifold! 😆

I'm going to experiment with the tooter et manifold by taking off the top of the plenum, and see if I can lengthen the runners from the inside. 😉


Greg
RJayHolland · Feb 6, 2014#89
Those are quite spectacular g ains, very nice! :)
malibuguyWestminster, MD · Feb 6, 2014#90
I may just have to get this...trade for my tooter? My car is DD more then race car ;)
tooterThread starterLos Angeles · Feb 7, 2014#91
Originally Posted by malibuguy ↑
I may just have to get this...trade for my tooter? My car is DD more then race car ;)
Sure, man. 🙂

I'll swap you straight across for a spacer as long as the tooter kit is unused. I'll pay the shipping to you if you pay the shipping to me. I have a Corolla manifold sitting in my shop that I need to build, and it'll save the CNC engineer the time to make another set. 👍

Greg
teoek9richmond va · Mar 2, 2014#92
How can I get one of those tooter adapter.
JustDidItUnited States · Mar 7, 2014#94
Originally Posted by tooter ↑
Here's the prototype on the manifold...

Picture not included in this copy

Picture not included in this copy

Greg
Originally Posted by tooter ↑
The tooters are done... 🙂

Picture not included in this copy

Picture not included in this copy

$265 including shipping

Greg
I'm really thinking about pulling the trigger on this and trying it on my 1NZ-FXE.. Should bolt right up.
tooterThread starterLos Angeles · Mar 7, 2014#95
Originally Posted by JustDidIt ↑
I'm really thinking about pulling the trigger on this and trying it on my 1NZ-FXE.. Should bolt right up.
If your intake manifold looks like this...

Picture not included in this copy

I have no idea as to the spacer's effect on your engine... 😕

However, it would be an interesting experiment because you have an Atkinson cycle engine and not an Otto. You'd also need at least 3 inches of free space in front of the intake manifold for the spacer to fit. From the drastically shallow design of that manifold it looks like free space might be at a premium. But I don't know your under the hood situation. Can you post a pic of the space in front of your intake manifold? Then you can go from there. Don't get one without first finding out if it would even fit.

Greg
CrankyOldManWest Michigan · Mar 7, 2014#96
Originally Posted by JustDidIt ↑
I'm really thinking about pulling the trigger on this and trying it on my 1NZ-FXE.. Should bolt right up.
DOOOO EEEET! Dyno runs or it didn't happen!
tooterThread starterLos Angeles · Mar 8, 2014#97
The only issue I can see is that very strange 1-2-4 (opposite of a 4-2-1 tri y exhaust manifold) intake manifold is specifically designed for an Atkinson cycle engine and is tuned for a very specific optimal rpm range. So an intake manifold spacer lengthening those extremely short intake runners is likely to push the curve outside that range. While there's a chance it might make it better, there's a greater chance of making it worse.


Greg
jetblastNor Cal · Mar 8, 2014#98
First off, thanks to Greg and Garm for all the fun stuff for these engines. Wondering about matching a spacer up with my dated Weapon R manifold. Greg, even if Malibu Guy's Tooter is used I might be interested. I also have a spare Corolla manifold that I've been meaning to "Tooterfy" so either way.

Thanks, Ken
malibuguyWestminster, MD · Mar 9, 2014#99
Mine isnt used but it is...if that makes any sense
tooterThread starterLos Angeles · Mar 9, 2014#100
Originally Posted by malibuguy ↑
Mine isnt used but it is...if that makes any sense
The last tooter I sold on ebay was listed in the category of "remanufactured" because it was a combination of old and new parts that were made into different product.

Greg