Yarisworld Archive

tooter's next manifold adventure...

151 posts · 75,762 views · page 3 of 4

Replies continued

dragoonmcIllinois · Mar 9, 2014#101
If this spacer is a hit I think someone needs to make a replacement engine cover to go with it
JustDidItUnited States · Mar 11, 2014#102
Originally Posted by tooter ↑
If your intake manifold looks like this...

Picture not included in this copy

I have no idea as to the spacer's effect on your engine... 😕

However, it would be an interesting experiment because you have an Atkinson cycle engine and not an Otto. You'd also need at least 3 inches of free space in front of the intake manifold for the spacer to fit. From the drastically shallow design of that manifold it looks like free space might be at a premium. But I don't know your under the hood situation. Can you post a pic of the space in front of your intake manifold? Then you can go from there. Don't get one without first finding out if it would even fit.

Greg
My 1NZ-FXE
Picture not included in this copy
tooterThread starterLos Angeles · Mar 11, 2014#103
Originally Posted by JustDidIt ↑
My 1NZ-FXE
Picture not included in this copy
Hey wait a minute... that intake doesn't look stock. 😉 Did you make a custom CAI for it?

There's an experiment you can try...
Unbolt the 5 bolts holding the intake manifold, yank all the hoses and put them out of the way, and then measure how far away from the head you can pull the manifold before anything hits the plastic reservoir of anything else in front of the engine. That will let you know whether or not a spacer will work. To me it looks tight in there, but it's hard to tell from pics. You'd know better than anyone else because you're right there. 🙂

Greg
dumbo0San Francisco, CA · Mar 22, 2014#104
Any update on the mileage?
Kaotic LazagnaCentral Valley, CA · Mar 25, 2014#105
Originally Posted by dumbo0 ↑
Any update on the mileage?
I filled up once so far after installing the Tooter spacer. You can track my mileage here:

http://www.fuelly.com/driver/07vios/yaris

So far, a slight increase in mpg. A bit too early to tell though.
Kaotic LazagnaCentral Valley, CA · Mar 25, 2014#106
Just filled up this morning, however it's missing about 30 miles of city driving. So my last two fill up's are with the Tooter spacer.
tooterThread starterLos Angeles · Mar 26, 2014#107
Thanks, Laz, for posting your gas mileage results. They're more credible coming from you than from me. 😉
It took a while for me to find out that the spacer allows the engine to operate just fine at lower rpms (1,000rpm to 2,000rpm) without any strain or lugging...

...even though my wife still revs it up. 😉


Greg
Kaotic LazagnaCentral Valley, CA · Mar 31, 2014#108
Originally Posted by tooter ↑
Thanks, Laz, for posting your gas mileage results. They're more credible coming from you than from me. 😉
It took a while for me to find out that the spacer allows the engine to operate just fine at lower rpms (1,000rpm to 2,000rpm) without any strain or lugging...

...even though my wife still revs it up. 😉


Greg
No problem. So far, three tanks with the spacer on now. Something to keep in mind is I don't know if my local Chevron has switched back to summer blend or not. But if comparing to around the same time last year, it's a 2-3 mpg increase.

3/22/13, 318.8 miles, 7.92 gallons, 40.2 mpg, $4.060

vs

3/20/14, 340.9 miles, 8.06 gallons, 42.3 mpg, $3.940
3/25/14 313.0 miles, 7.17 gallons, 43.7 mpg, $3.940

http://www.fuelly.com/driver/07vios/yaris (same link)
malibuguyWestminster, MD · Apr 2, 2014#109
Im pulling together to get some funds set aside for this. Just dropped my trans off for the Malibu to get rebuilt, sent the cam and lifters to get WPC treated as well. Too many projects!
tooterThread starterLos Angeles · Apr 3, 2014#110
Originally Posted by Kaotic Lazagna ↑
No problem. So far, three tanks with the spacer on now. Something to keep in mind is I don't know if my local Chevron has switched back to summer blend or not. But if comparing to around the same time last year, it's a 2-3 mpg increase.

3/22/13, 318.8 miles, 7.92 gallons, 40.2 mpg, $4.060

vs

3/20/14, 340.9 miles, 8.06 gallons, 42.3 mpg, $3.940
3/25/14 313.0 miles, 7.17 gallons, 43.7 mpg, $3.940

http://www.fuelly.com/driver/07vios/yaris (same link)
See if you can find out exactly when they make the change to Summer blend, so that you'll know whether or not the increase is the blend or the spacer. That will insure producing accurate results.👍


Greg
tooterThread starterLos Angeles · Apr 3, 2014#111
Originally Posted by malibuguy ↑
Im pulling together to get some funds set aside for this. Just dropped my trans off for the Malibu to get rebuilt, sent the cam and lifters to get WPC treated as well. Too many projects!
It's ok, Malibu... 🙂
There are still two available from this production run. And if there is still any interest after this run sells out, I can always have another run machined. 👍


Greg
Kaotic LazagnaCentral Valley, CA · Apr 3, 2014#112
Originally Posted by tooter ↑
See if you can find out exactly when they make the change to Summer blend, so that you'll know whether or not the increase is the blend or the spacer. That will insure producing accurate results.👍


Greg
I'll try to remember to ask tomorrow when I fill up. 😆
Kaotic LazagnaCentral Valley, CA · Apr 8, 2014#113
My local Chevron said they switched to summer blend, but didn't say when they did.
tooterThread starterLos Angeles · Apr 8, 2014#114
Originally Posted by Kaotic Lazagna ↑
My local Chevron said they switched to summer blend, but didn't say when they did.
That makes sense. My mileage has been better lately but I don't date my fillups. Same with my motorcycle. It goes over 70 mpg on Summer blend, and the last couple of fillups have all been 70+.


Greg
tooterThread starterLos Angeles · Jun 11, 2014#115
I'm down to the last spacer now... 🙂
DJYojimboChicago · Jun 11, 2014#116
Originally Posted by tooter ↑
I'm down to the last spacer now... 🙂
Greg, is there anyway you can hold the last one for me? I'm just waiting to finish my clinicals and waiting for the hospital to hire me which is very soon! anyway i can put a down payment?
tooterThread starterLos Angeles · Jun 11, 2014#117
Originally Posted by DJYojimbo ↑
Greg, is there anyway you can hold the last one for me? I'm just waiting to finish my clinicals and waiting for the hospital to hire me which is very soon! anyway i can put a down payment?

Don't worry, man... 🙂
Even if the last one sells out before you're ready to buy, I should be able to have a few more made within a month or so. The worst that could happen is that you might need to wait for just a little while.


Greg
DJYojimboChicago · Jun 11, 2014#118
Greg you are the man!!!! Once my first big check from the hospital arrives, i'm using it to buy a tooter!!!
DJYojimboChicago · Jun 11, 2014#119
i think i'm going to buy this and the trd rear sway bar and hold off on the dc sports header haha!
DJYojimboChicago · Jun 11, 2014#120
is anybody using this tooter spacer with an automatic tranny?
tooterThread starterLos Angeles · Jun 12, 2014#121
Originally Posted by DJYojimbo ↑
is anybody using this tooter spacer with an automatic tranny?
The one that shipped today is going to a guy with an auto. So as far as I know, he'll be the first to experiment with it. My best guess is that an auto trans will shift at slightly lower rpms because the stronger intake manifold vacuum signal will indicate less engine load, but I have no idea exactly what will happen. With my manual it easily short shifts at 2,000 rpms, and pulls in the next higher gear from under 2,000 without lugging the engine. That helps the gas mileage not needing to rev the engine as much in normal driving. Now if I could just get my wife not to rev the engine so much! 😆


Greg
j-sanMN · Jun 12, 2014#122
That would be me. Unfortunately, my Yaris lacks a tach, but I do have a ScanGaugeII. I'll try to see if I can't keep track of when the tranny shifts and compare that to after the spacer install. I'm hoping the tranny will keep up with any torque gains lower in the RPM range and shift accordingly. I hope this mod would end up giving me a little more low end power and squeeze out another MPG or two. I'll post up my findings after driving around with it a little.
tooterThread starterLos Angeles · Jun 12, 2014#123
You might be able to tell any difference of when the transmission shifts by feel. You already kind of know when it's going to shift according to how much you press on the gas pedal, and how much engine load there is such as grades. Gas mileage is a good indicator as it's sensitive enough to respond to more subtle factors.

It'll be really interesting to see what happens as this is uncharted waters. So if after driving with the spacer you feel that the benefits aren't worth the cost, please feel free to return it undamaged and I'll be happy give you your money back. 🙂


Greg
j-sanMN · Jun 12, 2014#124
That is very generous of you, Greg! I guess we will see how it goes and I hope my experiment with it will be of some use to you. Wish I had a manual tranny, but the wife just doesn't want to learn how to drive one...
tooterThread starterLos Angeles · Jun 13, 2014#125
I'm still trying to get my wife to rev the engine less so we can get better gas mileage. It's a lost cause. 😆


Greg
j-sanMN · Jun 29, 2014#126
Finally got the Tooter spacer installed today. Took me a while to get the time needed to do the install and I had to do a couple runs to the hardware shop for some tools. All together, the install was fairly straightforward and simple. I had to lengthen a couple hoses, but the other hoses seemed to have enough slack to make the move. I used the stock airbox without any issues. Greg has an excellent kit put together and the spacer is very well made - a perfect fit.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy





I let the battery remain disconnected during the install, which took about an hour. I had to remove the bolts that hold the coolant fill cap section to the throttle body and offset it in order to make the move. I was able to reconnect the fill cap section to the original mount using just one screw and made sure nothing was rubbing the hoses.

Picture not included in this copy




With the decorative engine cover back on, it looks virtually stock - especially with the stock airbox. Despite being only held on with 2 screws instead of the usual 4, the cover didn't rattle and the front edge was actually supported by the flange of the intake manifold.

Picture not included in this copy




Driving the car after the install was pretty much the same as before. I have an auto tranny and there were a few instances where the shifts came late at lower rpms. The tranny hung in the gear a little longer than what seemed like usual, but it stopped doing that after I got out of the residential roads and started going 50mph. I did not notice any change in how the car drove. I did test out the acceleration on highway onramps at WOT and it almost seemed like the car got up to highways speeds a tad faster than before, but then again, it could be the placebo effect taking hold. No info on fuel mileage yet since this is the first drive with it, but I can update this thread with my MPG with auto tranny once I have a few fill-ups done.
tooterThread starterLos Angeles · Jun 30, 2014#127
It might take a few cold start cycles for the ECU to relearn the new operating properties. On the dyno, the spacer lowered the torque peak from 4,100 rpm to 3,700 rpm, which is a difference of a little under 10%.

Picture not included in this copy

Without a tachometer that might be more difficult to detect, especially with the transmission torque converter fluid coupling compensating for the engine load. Let me know your driving impressions and gas mileage after driving it around for a while. :)


Greg
j-sanMN · Jul 1, 2014#128
Greg, I believe you mentioned the Weapon-R header you have also helped lower the torque curve a few hundred RPMs as well. I also recall you have a Magnaflow custom exhaust as well?

I am thinking of a header being the next mod. Looking at either the DC Sports or Weapon-R. Whichever header will help lower the torque curve further would be preferred. I have the JDM TRD muffler, but I don't think that contributes much for low end torque. A mechanic friend told me the issue with small engines and exhaust pipe diameter isn't an issue of backpressure, but that of exhaust gas velocity. Smaller pipes allow for higher gas velocity, which then improves the scavenging ability of the passing pressure wave, and helps low end torque. Larger pipes reduce the gas velocity, but allow for greater flow volume, which can improve high-end HP. Makes sense to me.

I just wonder if the mods are somewhat of a wasted effort with the auto tranny. Like you said about the fluid coupling, I would bet the tranny is responsible for a reduction in effectiveness. Still, the mods are fun to do and I enjoy getting under the car or hood and learning more about the workings of the Yaris.

I put about 35 miles on the spacer since install. I did notice the tranny doesn't downshift as readily while trying to accelerate on the on-ramp to highway speeds. Surprisingly, I am able to get a up to speed even in 3rd gear and not have to either force the tranny into 2nd or mash the gas pedal. Hope it gets better with more miles.
tooterThread starterLos Angeles · Jul 1, 2014#129
Originally Posted by j-san ↑
Greg, I believe you mentioned the Weapon-R header you have also helped lower the torque curve a few hundred RPMs as well. I also recall you have a Magnaflow custom exhaust as well?
Wow... you just brought up an interesting point that I hadn't even considered. 😲

The stated peak torque of a factory stock Yaris engine is 4,200 rpms.

Both dyno runs on that chart were done with the Weapon R exhaust header and the Micro Image Magnaflow center exhaust.

The peak torque on the run without the spacer is 4,100 rpm. So that means the header lowered the torque 100 rpms while the spacer lowered the peak by 400rpms. The two together produced the 3,700 rpm torque peak, 500 rpms lower than the stock peak.

I believe the 100 rpms are because there is such a short space in which to fit a header and yet retain the original position of the rest of the exhaust. So the tubes simply aren't long enough to make much difference.

On my Tacoma, I put a long tube header that uses folded runners to fit into the same space as the factory stock short tube header...

Picture not included in this copy


...and it lowered the torque peak by 650 rpms because there was enough room to pack long runners into a short space.


I am thinking of a header being the next mod. Looking at either the DC Sports or Weapon-R. Whichever header will help lower the torque curve further would be preferred.
From the dyno results you can know that the Weapon R is good to lower the peak 100 rpms. There's no way of knowing about the other headers, because I don't believe that anyone has ever tested them.


I have the JDM TRD muffler, but I don't think that contributes much for low end torque. A mechanic friend told me the issue with small engines and exhaust pipe diameter isn't an issue of backpressure, but that of exhaust gas velocity. Smaller pipes allow for higher gas velocity, which then improves the scavenging ability of the passing pressure wave, and helps low end torque. Larger pipes reduce the gas velocity, but allow for greater flow volume, which can improve high-end HP. Makes sense to me.
You're spot on. Axle backs can help performance without reducing the low end torque because the factory cat, tuned resonators, and the small diameter midpipe all work together to retain exhaust velocity.

I just wonder if the mods are somewhat of a wasted effort with the auto tranny. Like you said about the fluid coupling, I would bet the tranny is responsible for a reduction in effectiveness. Still, the mods are fun to do and I enjoy getting under the car or hood and learning more about the workings of the Yaris.
Yeah, because the fluid coupling is constantly altering the drive ratio to compensate for engine load, it muffles your perception of the effects. However, they're still there.

I put about 35 miles on the spacer since install. I did notice the tranny doesn't downshift as readily while trying to accelerate on the on-ramp to highway speeds. Surprisingly, I am able to get a up to speed even in 3rd gear and not have to either force the tranny into 2nd or mash the gas pedal. Hope it gets better with more miles.
That is an effect you can perceive. With slightly more torque, the transmission automatically shifts in to a higher gear sooner because it senses the engine is able to pull in that higher gear.

One major sensing element of engine load is intake manifold vacuum, which is a function of how hard the gas pedal is being pressed. When an engine produces more torque at lower rpms, the gas pedal is pressed slightly less, and the intake manifold vacuum is slightly higher. When a certain threshold of intake manifold vacuum is reached sooner, the transmission is signaled to shift to a higher gear sooner. That's what you're feeling. 🙂


Greg
j-sanMN · Jul 2, 2014#130
There is a slight power increase in the mid-3000RPM range. I kept an eye on the Scangauge whenever I was accelerating on the on-ramp and the car maintained a 3rd gear constant acceleration that was decent. I drive a regular route to work and back and frequently have to force the tranny into 2nd just to get an appreciable increase in speed.

For this first this first tank, it seems to be right in the norm for mileage. I usually get about 95 miles before the first bar in the gauge disappears. With the spacer on, I got 98. I usually go till the pump auto-stops for a consistent fill-up. I'm not expecting massive gains here, especially for the first tank, but we will see.

I wonder if a dyno sheet for an auto tranny would look much different from yours, Greg? I think you said your dyno run was done by putting the car in 3rd and then mashing the gas pedal?
tooterThread starterLos Angeles · Jul 2, 2014#132
Originally Posted by j-san ↑
There is a slight power increase in the mid-3000RPM range. I kept an eye on the Scangauge whenever I was accelerating on the on-ramp and the car maintained a 3rd gear constant acceleration that was decent. I drive a regular route to work and back and frequently have to force the tranny into 2nd just to get an appreciable increase in speed.

For this first this first tank, it seems to be right in the norm for mileage. I usually get about 95 miles before the first bar in the gauge disappears. With the spacer on, I got 98. I usually go till the pump auto-stops for a consistent fill-up. I'm not expecting massive gains here, especially for the first tank, but we will see.

I wonder if a dyno sheet for an auto tranny would look much different from yours, Greg? I think you said your dyno run was done by putting the car in 3rd and then mashing the gas pedal?
Yes, an auto trans dyno run would be different because when you mash the pedal the transmission kicks down to a lower gear. So the run would always begin recording at way higher rpms.

It might just be a coincidence, but making the runners 10% longer yielded a 10% lower torque peak. Although it's highly likely that relationship would break down pretty rapidly if continued.

Our mileage gets shot to hell because my wife drives the car, but when I drive it's easy to short shift at 2,000rpms without straining or lugging the engine.


Greg
tooterThread starterLos Angeles · Jul 2, 2014#133
Originally Posted by Kaotic Lazagna ↑
http://www.fuelly.com/car/toyota/yar.../07Vios/183168

Before I traded Vios in. I installed the Tooter spacer on entry 46. As you can see, every tank after that saw an increase of 2-3 mpg.
That's pretty impressive... 🙂
I did get to drive with the spacer when we took a trip and my best mileage was 42.1 mpg at 65-75 mph on the interstate. But just driving around town with no freeway, my wife has only been averaging 37.5 mpg.


Greg
j-sanMN · Jul 7, 2014#134
Hey Greg,

I know you run a short ram intake with cone filter. Did you have to do any mods to get that to work with the Tooter manifold or the spacer? I'm considering an intake like the AFE or maybe the K&N Typhoon. I doubt it would make serious gains, but I'm more curious about it improving MPG and perhaps a little performance increase.

On the other hand, I've also read that the stock intakes are engineered to deliver more flow than the engine could ever use and they also maintain a standing volume of still air within the box, ready to be sucked into the engine. Perhaps I should just look into a higher flow filter that fits the stock air box and go with that?
tooterThread starterLos Angeles · Jul 9, 2014#135
Originally Posted by j-san ↑
Hey Greg,

I know you run a short ram intake with cone filter. Did you have to do any mods to get that to work with the Tooter manifold or the spacer?
Just cutting the tube short so that I could fit the oversized BLOX velocity stack filter under the hood. The nice thing about an SRI is that it can easily be moved right along with the throttle body when it's relocated by the spacer.

Picture not included in this copy




When the engine is running at low rpms, any intake is underutilized, even the stock air box. I put a mini velocity stack on mine when I ran it. 🙂

Picture not included in this copy





I'm considering an intake like the AFE or maybe the K&N Typhoon. I doubt it would make serious gains, but I'm more curious about it improving MPG and perhaps a little performance increase.[/quote]

They do make a nice sound... but that's about it. 😉

On the other hand, I've also read that the stock intakes are engineered to deliver more flow than the engine could ever use and they also maintain a standing volume of still air within the box, ready to be sucked into the engine. Perhaps I should just look into a higher flow filter that fits the stock air box and go with that?
I tried all sorts of intakes, and none of them really made much difference when compared to manifolds, spacers, throttle bodies, headers, and exhausts.

Greg
dragoonmcIllinois · Jul 18, 2014#136
Hey all,
So my install of this spacer was on an auto trans.
I found that it actually hurt my mileage even after it re learned its stuff.
I had about a 2 mpg drop from last summer so i took it off and the mpg came back up to match last year
tooterThread starterLos Angeles · Jul 19, 2014#137
Do you realize that the spacer can't alter your air/fuel ratio? 😉

It just makes the intake runners longer. So it's obvious that there is something else going on besides the spacer.

But if you're not satisfied and feel that it is to blame for your gas mileage, simply return it undamaged with its gasket and all of the hardware and I'll refund your money. 🙂

Greg Mamishian
21444 Entrada Road
Topanga, CA 90290
Kaotic LazagnaCentral Valley, CA · Jul 19, 2014#138
Originally Posted by dragoonmc ↑
Hey all,
So my install of this spacer was on an auto trans.
I found that it actually hurt my mileage even after it re learned its stuff.
I had about a 2 mpg drop from last summer so i took it off and the mpg came back up to match last year
Were there any gaps between the spacer and the manifold and/or head?
tooterThread starterLos Angeles · Jul 19, 2014#139
That would very likely cause the ECU to throw a code.

I know this by personal experience because at the time I installed the prototype, the new gaskets hadn't come in yet. I was really anxious to run it and used an old gasket that was laying around. It triggered a fuel trim code because it leaked.

There's something else going on that we don't know about. But I won't argue with the guy. If he's not happy with his gas mileage and feels the spacer is the cause, he gets his money back.


Greg
Slitwrist SmileYork, PA · Jul 21, 2014#140
Originally Posted by tooter ↑
Do you realize that the spacer can't alter your air/fuel ratio? 😉

It just makes the intake runners longer. So it's obvious that there is something else going on besides the spacer.

But if you're not satisfied and feel that it is to blame for your gas mileage, simply return it undamaged with its gasket and all of the hardware and I'll refund your money. 🙂
Toot - you may want to remove your address for privacy reasons. Just trying to look out for the well being of forum members. Everyone on here might be a good person, but outside of YW, you don't know what scammers might try to do. You might want to edit your post (i removed the address from the quote I am posting) and PM it to the user it was intended for.
j-sanMN · Jul 21, 2014#141
I've now put a few tanks through my Yaris with the Tooter spacer. I did not notice any significant change in MPG. One tank was worse by about 1.8MPG and two tanks were better, one by 0.4MPG and the second by 1.1MPG. I think it has more to do with the variations in traffic and how heavy my foot is than the spacer. Sometimes I am running late and need to get moving faster and other days I am early and take my time accelerating and do more coasting. I imagine the ECU has learned what it needs with the spacer in place. I cannot feel any difference in daily driving, but it just seems like the tranny is more hesitant to downshift than before. I would understand that to mean the engine is probably pulling with a little more torque and thus, feels it does not need to downshift unless I force it or mash the pedal. I guess I still need to run more tanks to see if there is a greater change in MPG beyond the standard deviation. So far, everything runs as it should.
tooterThread starterLos Angeles · Jul 24, 2014#142
Originally Posted by Slitwrist Smile ↑
Toot - you may want to remove your address for privacy reasons. Just trying to look out for the well being of forum members. Everyone on here might be a good person, but outside of YW, you don't know what scammers might try to do. You might want to edit your post (i removed the address from the quote I am posting) and PM it to the user it was intended for.
Thanks for your concern. 🙂

I've been posting my name and address for years and have never had any problems being a public business . No one can scam me anyways. 😉


Greg
ezhacker1San Francisco · Jul 30, 2014#143
I was able to install the spacer and keep the heat shield on the AFE intake.

Did an initial test 6 mile test run city/hwy after ECU reset just to make sure car runs fine.

1. Idle warmed up RPM is lowered ~25rpm from 620 to 595.
2. Blipping the throttle is sensitive, like having the throttle controller on.
3. Letting the engine lug the car forward is much stronger. Sure the car is shaking but works stronger on my slight inclined driveway.
4. Although idle RPM is lowered, fuel consumption/hour hasn't changed, still 0.125/HR

Manual Transmission
Related Mods: AFE Intake, DC Sports axle back
tooterThread starterLos Angeles · Jul 31, 2014#144
Originally Posted by ezhacker1 ↑
3. Letting the engine lug the car forward is much stronger. Sure the car is shaking but works stronger on my slight inclined driveway.
I call that the "tractor effect". If you've ever driven a tractor, the engine does exactly the same thing... the high torque low rpm engines vibrate harmonically as they pull because the time between each power stroke is so long. We have a steep driveway that I measured with an inclinometer at 10%. I have fun going up it in my truck at below idle 500rpm. It just vibrates right up the hill like a tractor without lugging or bucking.

This is one of the strange attributes of the intake manifold spacer that doesn't show up on the dyno runs because it's "below the radar".

Off idle partial throttle performance is superb. If you have a manual transmission there's less clutch slipping needed just to get the car moving.

Greg
ezhacker1San Francisco · Jul 31, 2014#145
Yup, agree to all. I re-edit my previous post to fix error. I meant to say RPM was lowered but fuel consumption hasnt changed still 0.125/hr.

Doing the install did give me a chance to see how clean the intake valves were, there's some light oil that a catch can would take care of.

Edit:
After driving today looks like ecu is learning. Idle fuel consumption warmed up is now 0.116 gal/hr and subsequent using a catch can lowers it do 0.106 gal/hr.

Edit 2:
So i was stuck in stop and go traffic, and was able to use 2nd gear to keep the car crawling forward using no throttle at all, as long as i was not completely stopped. / 5th gear hill climb on a particular hwy of mine is also doable now, I normally have to go down to 4th. These two things helped me get 49 mpg on a 14.4 mile run, where 41% was city and 3 miles were that stop/go traffic.
tooterThread starterLos Angeles · Aug 5, 2014#146
Yeah, the car creeps really good... 🙂
I also have fun in traffic doing standing starts in first just with the clutch and no gas. It even does it on a slight incline with no bucking or stalling.

That's really outstanding mileage results! 👍 I'm glad you're able to record yours. I'll never know what mine can get because my wife drives the car more than I do... 🙄


Greg
ezhacker1San Francisco · Aug 5, 2014#147
If my wheels didnt weigh 43lb, i would be able to creep better lol. I might switch back to my 28lb Team Dynamics 14s.

I havent had a chance to dyno the car, but another evidence of the torque curve moved is seen in how DFCO now cuts off at 750rpm vs stock, which i believe is 1000 or 1100, so there's quite a change.
malibuguyWestminster, MD · Aug 29, 2014#148
Woohoo!

Picture not included in this copy

Hoping to base line the car tomorrow then test the spacer tuesday night
RakinBangladesh · Aug 29, 2014#149
Slightly off topic, hey tooter, what kinds of gains did you see with that BLOX filter and stock intake manifold?
malibuguyWestminster, MD · Aug 30, 2014#150
Installed it...YES!

Wow...part throttle performance is vastly improved. Feels like a 2 liter motor down low