tooterOriginal postLos Angeles · Nov 29, 2013#1Ok, tooter's back at it again with another adventure... 🙂
This time it's a bolt on intake manifold spacer that will make the manifold runners longer to lower the torque curve.
I installed a stock intake manifold so that I can check out all of the clearances, and it looks great with a generous 3.5 inches of empty space between the front of the manifold and the radiator reservoir.
Picture not included in this copy
A 2 inch thick spacer should be perfect with plenty of room to slip the manifold over the longer threaded studs. Plus we already have the tooling to do two inch deep machining. So far it looks like all green lights! 👍
I'll have a prototype spacer made (it'll look similar to this one I produced for Tacoma trucks.)...
Picture not included in this copy
Picture not included in this copy
It'll be dyno tested just like the manifolds. Then we'll see what the before and after torque curves look like, and go from there. 🙂
Greg
Replies 150
Mongoose7Liberty NY · Nov 29, 2013#2Nice work !!!!!!!!!!!! Waiting for the dyno results.
tooterThread starterLos Angeles · Nov 29, 2013#3 Originally Posted by
Mongoose7 ↑ Nice work !!!!!!!!!!!! Waiting for the dyno results.
So am I. 🙂
They'll be engraved similar to this except it'll be I.V instead of II.VII.
Picture not included in this copy CTScottUSA, CT · Nov 29, 2013#4Very cool!
After towing another Yaris 8 hours from Ohio to CT, I think my 6 cylinder Tacoma could use one as well to shift the torque curve down.
CrankyOldManWest Michigan · Nov 29, 2013#5 Originally Posted by
CTScott ↑ After towing another Yaris 8 hours from Ohio to CT...
Have you considered talking to a professional about this Yaris "hobby" of yours? =)
Tooter: this seems like it could be a solid mod for the non-boosted SMF AutoX crowd, since low-end torque is lacking so badly from our NA motor.
tooterThread starterLos Angeles · Nov 30, 2013#6 Originally Posted by
CTScott ↑ Very cool!
After towing another Yaris 8 hours from Ohio to CT, I think my 6 cylinder Tacoma could use one as well to shift the torque curve down.
Hey Scott, 🙂
Someone else makes one to fit your 1GR FE 4.0 engine... 👍
http://extremetruckperformance.com/?page_id=300 It's one half inch thick because of intake to hood clearance issues. The little 4 banger has an advantage of plenty of room on the side, so I made my spacer four times thicker. This is the prototype I'm currently running on my truck...
Picture not included in this copy Picture not included in this copy Picture not included in this copy Greg
tooterThread starterLos Angeles · Nov 30, 2013#7 Originally Posted by
CrankyOldMan ↑ Have you considered talking to a professional about this Yaris "hobby" of yours? =)
Hey Cranky, 🙂
Talk about what? I already know an extremely competent professional engineer who produces my concepts, and I already do all of my own testing, marketing, sales, and shipping. I really enjoy the personal autonomy of undiluted control over the complete process from concept to finished product sales and customer service. 👍 And I'm dealing with very small easily manageable product quantities because the market is paper thin.
Tooter: this seems like it could be a solid mod for the non-boosted SMF AutoX crowd, since low-end torque is lacking so badly from our NA motor.
Well, I don't know that yet. A dyno tested prototype will render the final verdict as to how solid a mod it might turn out to be.
By the way, what's SMF AutoX?
Regards,
Greg
tooterThread starterLos Angeles · Nov 30, 2013#8BEEFnorth carolina · Nov 30, 2013#9I think he more meant a professional to help market your products and get your name out there. i feel like there are a lot of guys out there like me. i love power but price point is an issue. i'd love to have the manifold garm sells but have better places for $700 to go. if i could get the results (or close) without the looks (his mani is nice), i would be willing to go that route.
I am eagarly watching this project.
CrankyOldManWest Michigan · Nov 30, 2013#10 Originally Posted by
BEEF ↑ I think he more meant ...
Nope, that was to CTScott. I think he has an addiction to Yarii. =) Tooter has been doing an excellent job of bringing these products to the market, however thin it may be.
SMF = Street Modified FWD in Autocross. I'm not sure how someone would get to SMF with a Yaris without going forced induction (suspension/wheel width/cams?) or dropping in another Toyota engine, but any modifications between the TB and the engine puts you in SMF. At the local level I can almost keep up with the other SMF cars, but any time someone from the National level shows up (in a Civic, normally) it's game over.
tooterThread starterLos Angeles · Nov 30, 2013#11 Originally Posted by
BEEF ↑ I think he more meant a professional to help market your products and get your name out there.
Yikes, beef! 😲
That's the
LAST thing I want to do! That would set into motion a set of circumstances I shudder to contemplate, and I don't ever want to go there.
I'm totally satisfied with the present scale of operations just as it is because I'm completely
free to express my own vision and to implement my own ideas. I can go from a virtual concept to a finished saleable product in just a couple of months instead of giving up my autonomy and control by diddling away years of haggling around with third parties.
The engineer who does my design and machining does small manageable batches in his spare time, which are in total sync with market demand.
So far, with both the tooter intake manifold, tooter kits, and tooter II.VII spacer I've been able to meet my goal of recovering all of my R&D production and sales costs, and ending up with free products for my own personal use. And I'm totally happy with that. It's an elegantly simple setup that works like a charm. I get
all the fun and adventure of creative innovation... but with
none of the business and financial headaches. 👍
1. Autonomy The freedom to act independently.
2. Mastery Refining ways to do things better.
3. Purpose The ability to implement my vision.
I'm just not willing to give up any of those. 😉
Greg
cali yarisCanoga Park, CA · Nov 30, 2013#12 if i could get the results (or close) without the looks (his mani is nice), i would be willing to go that route.
Unfortunately, quality doesn't work that way, or I'd be offering a different product. The looks are a result of good workmanship. 🙂
BEEFnorth carolina · Nov 30, 2013#13Cali, i wasn't knockin your stuff. almost everything on my car came from MI.
1.5Tampa · Nov 30, 2013#14Ive seen the TB spacer and those usually produce gains so id be excited to see how this does too. Have you thought of doing a tb as well tooter?
tooterThread starterLos Angeles · Nov 30, 2013#15 Originally Posted by
1.5 ↑ Ive seen the TB spacer and those usually produce gains so id be excited to see how this does too. Have you thought of doing a tb as well tooter?
No.
Throttle body spacers don't actually do anything except slightly enlarge the air volume of the plenum. The CNC engineer at the design shop told me that once the intake runners are reading infinite (open space) at the entrances where they connect to the plenum, enlarging the plenum makes no difference.
In contrast, lengthening the intake runners themselves does alter the operating properties of the intake manifold by shifting the torque curve lower in the rpm range.
Picture not included in this copy I'm pretty sure that a 2 inch thick Yaris spacer will yield results similar to the 2 inch thick Tacoma spacer as the two intake manifolds are of a similar design. I wanted to do a spacer for the tooter, but it already takes up almost all of the space in front of the engine.
Picture not included in this copy Greg
CrankyOldManWest Michigan · Nov 30, 2013#16 Originally Posted by
tooter ↑ No.
Throttle body spacers don't actually do anything except slightly enlarge the air volume of the plenum. The CNC engineer at the design shop told me that once the intake runners are reading infinite (open space) at the entrances where they connect to the plenum, enlarging the plenum makes no difference.
In contrast, lengthening the intake runners themselves does alter the operating properties of the intake manifold by shifting the torque curve lower in the rpm range.
Aah yes, the old Helmholtz resonator. I've always wondered what the plenum side of that equation is, since the only readily available information is about the neck/runner length and volume of the resonating body.
tooterThread starterLos Angeles · Jan 10, 2014#17Ok... enough goofing around over the holidays. I'm back in the saddle again. 🙂
A couple of nylon blocks for two prototype tooter I.V spacers have been ordered along with the blocks to make more tooter II.VII spacers. They should be in next week. 🙂
Greg
tk-421Dagobah · Jan 10, 2014#18 Originally Posted by
CrankyOldMan ↑ Have you considered talking to a professional about this Yaris "hobby" of yours? =)
I think he was talking about CTScott and his (un?)healthy amounts of geekiness surrounding the Yaris. 😉
tooterThread starterLos Angeles · Jan 10, 2014#19 Originally Posted by
tk-421 ↑ I think he was talking about CTScott and his (un?)healthy amounts of geekiness surrounding the Yaris. 😉
My Yaris obsession has also spread to the Tacoma... 😉
https://www.youtube.com/watch?v=hvIBURPwtXw Klink10910 · Jan 10, 2014#20Suscribed
tooterThread starterLos Angeles · Jan 17, 2014#21The shipment of nylon blocks came in yesterday. 🙂
Picture not included in this copy
The two shorter blocks on top are for a couple of Yaris prototypes for dyno testing. The rest are for another production run of tooter Tacoma spacers. There's a set of aluminum parts in the works right now, as I'm also building another tooter intake manifold.
So there's three projects all going on at the same time. 😉
Greg
tooterThread starterLos Angeles · Jan 24, 2014#22The prototype spacer should be ready any day now.
(ooh goody 🙂 )
malibuguyWestminster, MD · Jan 24, 2014#23Sweet. I finally welded my tooter together last week. I'm going to dyno before and after as well. Wont be for another couple weeks once I make the intake and hopefully get a 'rolla tb
tk-421Dagobah · Jan 24, 2014#24 Originally Posted by
malibuguy ↑ I finally welded my tooter together last week.
That sounds painful. 😁
malibuguyWestminster, MD · Jan 24, 2014#25Rofl
tooterThread starterLos Angeles · Jan 25, 2014#26The very first tooter I.V intake manifold spacer prototype is done... 🙂
Picture not included in this copy
Klink10910 · Jan 25, 2014#27Excellent. Looking forward to testing.
lambrosKALAMATA MESSINIA GREECE · Jan 25, 2014#28What is the benefits of this spacer?
CrankyOldManWest Michigan · Jan 25, 2014#29 Originally Posted by
tooter ↑ ...lengthening the intake runners themselves does alter the operating properties of the intake manifold by shifting the torque curve lower in the rpm range.
Originally Posted by
lambros ↑ What is the benefits of this spacer?
Please read the thread before asking questions that have been answered.
lambrosKALAMATA MESSINIA GREECE · Jan 25, 2014#30Thank you
RJayHolland · Jan 25, 2014#31I suppose a flatter torque curve :) Longer runners give you that whilst shorter runners give you a bit extra horsies.
That's the theory at least. I know there are some cars with variable intake runners.
tooterThread starterLos Angeles · Jan 25, 2014#32 Originally Posted by
RJay ↑ I suppose a flatter torque curve :) Longer runners give you that whilst shorter runners give you a bit extra horsies.
That's the theory at least. I know there are some cars with variable intake runners.
You can see on this dyno chart exactly what 2 inch longer runners do. This is with the tooter II.VII spacer on my Toyota Tacoma.
Picture not included in this copy Blue line is without the spacer, and the torque peak is 3,150rpm.
Red line is with the spacer, and the torque peak is 2,900 rpm.
Basically it moves the whole curve downward towards lower rpms as well as fattening up the curve a bit.
Picture not included in this copy Tacoma manifold with spacer...
Picture not included in this copy I'm expecting a similar effect on the Yaris when I dyno test it. How much, who knows? And that's what we'll find out. 😉
Greg
tooterThread starterLos Angeles · Jan 25, 2014#33 Originally Posted by
lambros ↑ What is the benefits of this spacer?
I don't mind you asking because the threads get large and I wouldn't expect everyone to read everything. I just answered your question in the last post. 🙂
Latest news... the prototype is being engraved with the tooter logo today, and I pick it up tomorrow morning!🙂
So I'll try to get it installed and running on Sunday and I'll give you guys my driving impression. If I can find time off work, I'll get it dynoed this week. 👍
Greg
tooterThread starterLos Angeles · Jan 25, 2014#34Ta Da... 🙂
Picture not included in this copy
Now there's two tooters... 😉
Picture not included in this copy
malibuguyWestminster, MD · Jan 25, 2014#35Looks "toots" ;)
RJayHolland · Jan 26, 2014#36Looks nice, and I estimate the tacoma runs a bit smoother and lazyer with the 2 inch?
Still that is a pretty flat torque curve to start with.
tooterThread starterLos Angeles · Jan 26, 2014#37 Originally Posted by
RJay ↑ Looks nice, and I estimate the tacoma runs a bit smoother and lazyer with the 2 inch?
Still that is a pretty flat torque curve to start with.
Yes it's very flat. The Tacoma is a slow turning low end torque industrial engine. The redline is only 5,600 rpm and there isn't much over 4,000 rpm.
The dyno charts don't show it but the truck pulls like a tractor right from idle and even below. I measured the slope of my driveway with an inclinometer and it's 12 degrees. My fully loaded truck climbs right up it even down to only 500 rpm without stalling. It vibrates just like a tractor engine. If you've ever driven a tractor, you'll know exactly what I'm talking about. I live and work in a steep canyon and am always crawling up and down the hills in first gear, so this spacer
exactly suits my own needs. 👍
Here's the dyno run with the tooter spacer. All the sound is the intake because the exhaust was stock when I ran it.
http://www.youtube.com/watch?v=H6ofUy8_-6Q And an acceleration run, same spacer, stock exhaust.
http://www.youtube.com/watch?v=hvIBURPwtXw Greg
tooterThread starterLos Angeles · Jan 26, 2014#38Here's the prototype on the manifold...
Picture not included in this copy
It doubles the length of straight runner section before entering the head as well as adding a little more volume to the manifold.
Picture not included in this copy
This with the spacer on the engine. Installation is stupid easy. 🙂 There's tons of clearance everywhere, and even the oil dipstick tube fit perfectly. You can hardly tell it's there because it's covered up by the fuel rail and the wiring loom.
Picture not included in this copy
With the cover on, it's literally invisible. I bet it wouldn't even be noticed on a smog test.
Picture not included in this copy
I drove it around today, but couldn't really tell any difference, because I'm so used to driving the tooter ET manifold and the larger Corolla throttle body. So that was giving up a lot of advantages. Still it ran good with no issues. I had disconnected the battery so that the ECU could adjust back to the different stock manifold, the different throttle body, and to the spacer as well. All three being changed at exactly the same time caused the ECU hunt around for quite a while trying to figure out the right idle. But it eventually stabilized and the engine runs just fine. 🙂
I'll see about dyno runs this week, if I can find the time.
Greg
Ryze268Antigua & Barbuda · Jan 28, 2014#39Can't wait to see some Dyno results :)
CrankyOldManWest Michigan · Jan 28, 2014#40So stealth!
ViperoniBrampton, ON · Jan 28, 2014#41Awesome!
Hope the dyno shows something the butt dyno doesn't :)
tooterThread starterLos Angeles · Jan 29, 2014#42 Originally Posted by
Viperoni ↑ Awesome!
Hope the dyno shows something the butt dyno doesn't :)
Yeah, the dyno is the only way to know for sure. I'll do some runs as soon as I can, but I don't think it'll be this week as I'm on starting a big job tomorrow. The car also needs to be driven for a while to settle in to all of the new operating parameters. So far it only has 5 miles on the new setup. And I can't tell because I'm already so used to driving it with the larger more responsive 1ZZ throttle body and the tooter I was running already has longer intake runners than the stock manifold.
Greg
exileddeusAustell, GA · Jan 29, 2014#43Good stuff!! Keeping an eye on this.
tooterThread starterLos Angeles · Feb 1, 2014#44My wife has been driving the car all week so the ECU is all dialed in now. Today, I finally got a chance to drive the car a decent distance, and it definitely has more low rpm torque right from off idle to 2,000 rpm. 🙂 I did my "clutch test", and can let out the clutch pretty quick with no gas and the engine won't stall. I used 2,000 rpms as the shift point to get a good feel for how it accelerates at low rpms and drove it at 35 mph in 5th gear to see how it handles the low rpm load. Feels like driving a little truck.😉
My wife had said that the exhaust sounds "funny", and after driving it today, wow... it sure does! 😲 Up to now I had driven it only about 5 miles after first installing the spacer, and had babied it not knowing how it was going to work. So I didn't hear what it sounded like at higher rpms. When you get on the throttle, the engine makes this really strange rrrrrrrrrrrrrrrrrrrrr sound like a 4 cylinder motorcycle engine. So the spacer actually did change the operating parameters of the engine quite a bit.
Dyno testing will be this coming Monday the 3rd if Harry can fit me into his schedule, so we should get to see the results soon.
Man, I can hardly wait... 🙂
Greg
tooterThread starterLos Angeles · Feb 1, 2014#45Took the car out again and on the freeway for the first time. Flat out acceleration there's nothing at the top end, but then I'm used to the 1ZZ throttle body with the tooter. It cruises with very little throttle At 2,500 to 3,500, and feels great, so I'll begin taking gas mileage readings when I fill it up after the dyno test on Monday.
On the bottom it undeniably feels stronger. I did my "driveway test". It's a 12% grade and from a standing start, the car goes right up at only 400 rpm with no bucking or stalling. The road that goes to my house has a really steep grade, so I also use that one as a test because I'm constantly going up and down and know exactly how it feels. When purposefully short shifting out of first down to only 1,000 rpm in second, it accelerates right up the hill with absolutely no bogging or bucking or straining and without needing a lot of throttle. Now I'm starting to get excited about this as it's passing all of my torque tests with flying colors. :)
But my impressions are highly subjective. That's why we need the dyno so that we can see some real numbers. 👍
Greg
Ryze268Antigua & Barbuda · Feb 1, 2014#46Well done Greg, keep the updates coming :)
malibuguyWestminster, MD · Feb 2, 2014#47Badass
GolddeenohColumbia, SC · Feb 2, 2014#48very important to have low end torque, for um... red light acceleration. you know, when leaving red light and trying to get up to proper speed limits and economy speeds.
tooterThread starterLos Angeles · Feb 2, 2014#49 Originally Posted by
Golddeenoh ↑ very important to have low end torque, for um... red light acceleration. you know, when leaving red light and trying to get up to proper speed limits and economy speeds.
On the test drive I accidently
spun the wheels taking off. And I
never do that. It was quite a surprise! 😲
Greg
cali yarisCanoga Park, CA · Feb 2, 2014#50 for um... red light acceleration. you know, when leaving red light and trying to get up to proper speed limits and economy speeds.
heh, that made me chuckle.