Yarisworld Archive

1zz Throttle body review/tips

155 posts · 147,750 views · page 2 of 4

Replies continued

mattymoGA · Dec 18, 2014#51
I've adjusted the epoxy screw to get good idle, but crazy georgia weather swings may be confusing the learn. I have an aem intake. My vacuum and af ratios look ok in torque. I do seem to get more trouble with atmospheric pressure changes too.

After you solved everything, did u scan the ecm? Sometimes this code wont actually trigger the check engine light. Thanks.

Sent from my GT-P5210 using Tapatalk
tooterLos Angeles · Dec 24, 2014#52
Yes... and the scanner showed no pending codes.


Greg
mattymoGA · Dec 24, 2014#53
Greg, what warm idle rpm did u settle to? Thanks again.

Sent from my GT-P5210 using Tapatalk
instantninjacold lake alberta, canada · Jan 12, 2015#54
I put a 1zz throttle body on my yaris this fall, after adjusting the idle and resetting the ecu its has worked great. it does idle higher than with the original tb and it doesn't like very cold weather. -30/-35 it throws a lean code and I had the throttle plate get stuck, but other than that it has been good and there was a noticeable increase above 3500rpm, although I don't know how much is the throttle body and how much is the tooter I put on at the same time.
axiomColorado · Jan 27, 2015#55
Does anyone know of a way to get rid of the "lag" when letting off the gas? Mine stays at it's rpms for a second before dropping down after letting off the gas with or without the clutch in. It's quite annoying.
mattymoGA · Feb 2, 2015#56
If you're referring to the quick jerk while letting off the gas, try backing idle screw out more. I'm still struggling with this nyself. Getting it set right for the ecu to be happy is a tricky bitch. Swings in weather make it worse. Anyway, if you're having a laaaaaag of mure than half a second or so we might be talking about two different things. Try scanning ecu. If you get idle control system code, ecu is not happy yet. It can even be a pending code that won't trigger CEL.

Sent from my GT-P5210 using Tapatalk
axiomColorado · Feb 3, 2015#57
For example, if I'm running at 4000 rmp, and I let off the gas, it'll stay there for a half second, then drop. My original tb would drop the second I let off the gas.

I'll have to look and see if the idle screw has ever been messed with. I may need to chip away at the epoxy. If I do, do I then need to replace it once I find a good setting?

As far as codes, I'll need to run over to an auto shop sometime to see.

PS-I'm tired of people thinking I want to race them at the first stop light by my house.......stupid high rpm before engine warm up.
zenN. Chas, SC · Apr 19, 2015#58
So I attempted to do the throttle body swap but realized I can't connect it to the stock intake due to the outlet of the throttle body being larger than the hose...is the best way for me to solve this to buy a 2005 Corolla / Matrix intake hose? I'm trying to keep it looking stock as much as possible due to my 2014 is still under warranty.
KTSTrinidad and Tobago · Apr 19, 2015#59
Turn the flex hose around and use a little bit of grease. It will be a tight fit.
zenN. Chas, SC · Apr 19, 2015#60
I'll have to try that again, was trying my hardest to get that method to work
phaznetYGK · Apr 23, 2015#61
I've been wanting to do this mod for some time, I just want to get the right part.
I have a 2007 yaris sedan. I see the part number we want is the 22030-0D030, but all I can find locally is the 0D031! In that case, would I simply need to do a chip swap?

phaznet
ezhacker1San Francisco · Apr 23, 2015#62
I haven't read through the entire thread, but a tip i have found I want to share with you all.

PORTMATCH THE TB!! I got my throttle body from a sedan friend, and he had meticulously port matched the intake manifold to the tb, I have experience no extended high rpm or pulsing at all. Just the normal 2700rpm at start which drops to normal operating rpm within like 20 seconds or so, and this is which the car not moving.

But like others, i do have the "rpm holding lag" not always maybe once in a while, but i havent had an issue like, trying to get into a gear and grinding..
zenN. Chas, SC · Apr 24, 2015#63
I successfully installed it except I'm getting the pulsing revs and makes it seem like I want to race everyone lol..I dont quite have a hex small enough to adjust the idle screw
phaznetYGK · Apr 24, 2015#64
What was the part # on the throttle bodies you installed?
zenN. Chas, SC · Apr 24, 2015#65
0D030 off a 2005 Toyota Corolla
phaznetYGK · Apr 24, 2015#66
Can I use a 0D031?
MedMantleSouth Africa · Apr 28, 2015#67
Hey guys, I found a (Part Number) 22030-0C010 throttle body, it looks similar to the one you guys use, only visual difference is the coolant pipes are angled differently.. The Bore diameter is also 55mm.. I can't find a 2nd hand 1ZZ TB in my country and the guy that wants to sell me this one is giving it to me at a good price. I plugged the connector into it and it opens when I depress the accelerator, it should work the same as the 1ZZ once fitted?
MedMantleSouth Africa · May 8, 2015#68
Okay, so I have installed my PN:22030-0C010 TB with great difficulty, had occilation on the first startup! Second time I started up I idled in the 3000 RPM range but it gradually came down to about 800 RPM's (idle) more or less and it has been driving fine for 2 days so far!

No chip-swap, I chipped away the idle screw's epoxy to test fit a hex wrench at the shops but I haven't adjusted it yet! No CEL and it's been totally normal so far apart from the 2000RPM idle for 20 seconds when I start up in the morning!

I can feel the 5th gear bite harder even at a lowly 60kph, not much but noticeable! And a slight wheelspin on my hill of a driveway today proved that the response is more than I'm used to! I put my stock airbox back and can swear that it's got a slightly stronger growl! I hope my luck holds!! :D
LTHatchNewark NJ · May 10, 2015#69
MedMantle:Your Yaris is a 2nzfe 1.3? Have a look at this thread: My Dyno Run
Japle did a bunch of dyno runs with his 1nzfe yaris, for some reason his 1nzfe came with the 2nzfe intake manifold. After installing the 1nzfe intake manifold he gained 14whp, just a guess here but i think the 1nzfe intake manifold may be an upgrade to the 2nzfe guys. You definitely won't gain the power Japle did but there might be a few horsepower in there to gain.
MedMantleSouth Africa · May 11, 2015#70
Wow, that is amazing!! I'm actually still contemplating doing the engine swap to a 1NZ-FE! I just wanna make double sure that it's plug and play. It is my first car and the only car I drive and wouldn't want to sit with problems! I'm stupid when it comes to understanding HP figures.. how much of a difference would I feel going from 1.3l to 1.5l? is it worth the $1500 I roughly worked out for the engine and labour?

And just a side note, it has been a week driving with my TB, no problems apart from the high rev on startup! Can definitely feel the difference, especially when I accelerate after a gear change! :D
LTHatchNewark NJ · May 12, 2015#71
The difference would be noticeable, but worth 1500 that's completely up to your judgement. Being a plug n play swap i have no clue, but give it a few days i'm sure someone who has done it can give you the run down on all it takes to swap it.

Did the TB swap make your intake louder? How is your low end torque and mid range torque also?
MedMantleSouth Africa · May 13, 2015#72
It might cost a lot less and will work out a lot cheaper than doing anything else to my 1.3 :P will wait and see! :)

I originally had my OEM intake flipped with the filter exposed but the day I put the TB in I replaced my filter and mounted everything up stock, so unfortunately my intake got softer anyways. It does seem throatier, but it's hard to tell with my cat-back exhaust noise :/

I seriously feel a difference in all area's! Launching feels a lot more responsive and "grippier" and hill climbs feel a tad better! The biggest difference is in changing gears for me, it feels nearly seamless compared to the jerky nature it originally had... maybe it's all in my head? lol, but I'm happy and it only cost me $104 in total :) oh and I can hear and feel the extra air coming in when I depress the accelerator completely and my exhaust tone seems "higher" at that point than it normally was, so it MUST mean something! :D
LTHatchNewark NJ · May 14, 2015#73
Very nice MedMantle, are you planing any other mods in the near future for your Yaris?
MedMantleSouth Africa · May 15, 2015#74
I was planning a lot of things, but money is tight so I'm thinking more realistically.. gonna focus more on cosmetics and luxury! My sister traded in her T-sport for the 1.3 and moved to America, damn :'( , it's a tough downgrade but I'm making the best of it :P

Just recently fitted OEM Electric Windows that I bought second hand, I had to make the main harness though but so far so good!

I'm saving hard now to get the money to buy some lowering springs. I was gonna wait a bit longer and get coil-overs but I'm not dedicated enough to get the whole stance look so a decent drop is all I'm interested in!

I'm trying to keep the car as stock looking and sounding as possible, that is why I just went for a 8" sub and it's the reason I'm gonna get my cat-back "softened". I removed all my stickers and allready sold my angel-eyes..
I just kinda had a mindset change and its cost me a lot but I don't regret any of my purchases that I'm undoing! :P
tooterLos Angeles · May 16, 2015#75
Originally Posted by zen ↑
I successfully installed it except I'm getting the pulsing revs and makes it seem like I want to race everyone lol..I dont quite have a hex small enough to adjust the idle screw
Do not drive it like that with the engine fishing around trying to find the idle speed. It's unsafe. Don't ask me how I know. 😆

I found the closest hex that's just slightly larger and tapped it in with a small mallet for a really tight fit. You do NOT want to strip out that tiny screw.

Picture not included in this copy

Make sure the epoxy is cleared and use a little bit of liquid wrench to help it break free. It will make a cracking noise when it moves, and that's good. When it moves take it one full turn out (counterclockwise) to allow the butterfly to close enough for the ECU to find a stable idle.


Greg
KTSTrinidad and Tobago · May 17, 2015#76
I agree that the 1zz throttle body is a great mod. I loved driving my 2007 Vitz RS with it. The car had much better throttle response its quite noticeable

Is it worth doing this mod with the Blitz Supercharger Kit?? What you guys suggest?

I have the S/C installed about a month now and the car drives great. Can it really drive that much better if I install the 1zz tb. Of course I will have to port match the intake pipe.
Also if I do port match the intake will I be able to reinstall the 1nz tb with out any issues?
invader166Langley, BC · May 17, 2015#77
Is it worth doing this mod with the Blitz Supercharger Kit?? What you guys suggest?
Absolutely! By increasing the diameter of your throttle-body, you're further improving the air-flow by providing less restriction for the air to reach the intake manifold. More air means you can increase your air-fuel ratios. 😉

Just be careful, there is a limit on how much the engine can sustain.
KTSTrinidad and Tobago · May 17, 2015#78
thanks invader166.
HANZO_187Wintergarden, FL · May 28, 2015#79
Ok so I'm back from the dead...!!!

Hanzo is BACK!!

What are the parts for the throttle bodies that fit the 1NZ-FE?

I have the sedan, and I'm looking to make some good gains.
I read a few different tb's people have used and some have twisted the hex bolt and some haven't.

I haven't read through these threads lately, if some one could appoint me to the Throttle Body thread and can someone tell me if TOOTER still does custom work??

Miss this Forum, glad to be back!!
phaznetYGK · Jun 10, 2015#80
Finally installed the 1zz from a corolla, got the part from the local wrecking yard.
The only part # I could find was the ODO31. At first I got a check engine light, diagnosed it and 5 things came up. The next day the check engine light was gone :) I'm glad I wont have to do the chip swap!!!

The engine starts with a high idle, close to 3000 rpm. Only thing now is that epoxied screw. Going to tackle that now and post back.

Also, for anyone not sure about whether they want to do this mod - DO IT!!! You will feel a difference, especially if you've done other performance mods to your Yaris.
MedMantleSouth Africa · Jun 10, 2015#81
After riding tonight I must say that after 100KmPH in 5th gear I can definitely feel the car pulling much harder and climbing in speed way faster! So definitely a improvement on the top end as well! One day I'll get the courage to port match my Intake Manifold to the TB and see what it does :P
phaznetYGK · Jun 10, 2015#82
I'm stuck!

This damn epoxied bolt/screw. I can't turn the damn thing. I've chipped away all the epoxy, plus used a tiny bit of paint thinner to eat away at the epoxy. I tried something a member did, which was to tap a slightly larger diameter hex key, but I couldn't torque it enough to get it to turn, it just stripped it.

I need help!
CrankyOldManWest Michigan · Jun 10, 2015#83
I did the same thing with mine. I ended up drilling it out and replacing it with a 1/4-20 bolt

Sent from my XT1031 using Tapatalk
phaznetYGK · Jun 10, 2015#84
That seems a bit risky, but I might use it as a last resort. How long is the screw? What is it holding/pushing?
CrankyOldManWest Michigan · Jun 10, 2015#85
Yeah, you need to remove it from the intake completely. I don't recall the length, probably 1 1/4" socket head cap screw. It's for adjusting the idle position of the butterfly valve.

Sent from my XT1031 using Tapatalk
phaznetYGK · Jun 23, 2015#86
Finally got that screw to turn, was the hardest part of install for me.

I've turned it 1 full rotation counter clockwise, but I haven't really noticed a difference!

How much did you guys turn it?

Thanks
scod4025Sacramento · Jun 23, 2015#87
With mine needed to get a tach on it to get it to idle right ended up buying a scan gauge II and then got it dialed in right and was closer to about two and half turns in to get it to 700 rpm at idle
RigaudRigaud, Quebec, Can. · Jun 23, 2015#88
790rpm and up you'll get a code for high idle. I got mine at about 600rpm on idle, been over a year and zero issues. I'll finally have time to mod a 1zz aluminum intake and have everything match properly. Just the 1ZZ TB alone you still don't get the full benefit.
invader166Langley, BC · Jun 24, 2015#89
Originally Posted by Rigaud ↑
I'll finally have time to mod a 1zz aluminum intake and have everything match properly. Just the 1ZZ TB alone you still don't get the full benefit.
Are you moding a 1zz aluminum intake manifold from an '98-'02 corolla? Is it a big project. Please let us know how it turns out!
I wonder if I could do the same for a plastic intake manifold from an '03+ corolla...
RigaudRigaud, Quebec, Can. · Jun 24, 2015#90
Originally Posted by invader166 ↑
Are you moding a 1zz aluminum intake manifold from an '98-'02 corolla? Is it a big project. Please let us know how it turns out!
I wonder if I could do the same for a plastic intake manifold from an '03+ corolla...
Bolt holes to the head don't match but the ports do 100%. I'm cutting off the existing mounting plate, machining a new one to fit, tig weld the port it. The other end is a 3 stud mount for the TB, cutting that off too, machine, weld, port and voila. I don't know the exact year but looks like a celica intake.
invader166Langley, BC · Jun 25, 2015#91
^^^ +1 for custom manifold!🎉
bebeeloStockton, CA · Jun 29, 2015#92
so all I have to do is install the new throttle body, then either loosen up or tighten the idle screw?
MedMantleSouth Africa · Jun 30, 2015#93
Originally Posted by bebeelo ↑
so all I have to do is install the new throttle body, then either loosen up or tighten the idle screw?
Yes. Install it, make sure the gasket is sealing properly and just loosen the idle screw to reduce the idle RPM's and tighten to increase. Make sure to chip away the resin on that screw before installation :)
bebeeloStockton, CA · Jun 30, 2015#94
Originally Posted by MedMantle ↑
Make sure to chip away the resin on that screw before installation :)
do I use A toothpick or a screwdriver to take it out?
MedMantleSouth Africa · Jul 1, 2015#95
Originally Posted by bebeelo ↑
do I use A toothpick or a screwdriver to take it out?
It's quite hard. I used a small flat-headed screwdriver and a hammer to tap at the resin "carefully" and to dig in it. Make sure to get it all off so the screw doesn't strip when you try to adjust it.

Maybe someone else knows a safer or easier way?? :P

And remember it is a Allen Key screw. It was quite difficult to source the correct one here where I live but everything is difficult to find over here :P
bebeeloStockton, CA · Jul 1, 2015#96
Thanks for the specific info medmantle👌 btw im using a CAI so do i need a specific intake hose adapter thingy like this one or could i uss the one that originally came with CAI?

1 attachment not included in this copy

scod4025Sacramento · Jul 1, 2015#97
I was able to use the one that came with my CAI just took a little bit of finesse. Just rounded the inside edge a bit then little bit of oil and it slide on


Sent from my SM-G386T using Tapatalk
MedMantleSouth Africa · Jul 2, 2015#98
I still have the stock intake. Like 'scod' said, just give it all you've got! :P I had to turn my stock intake pipe around to get it to fit and it was still quite tight and difficult to get over, but I eventually got it. I would have loved to be able to use a adapter like that but we have almost no aftermarket car stuff where I live. :)
RigaudRigaud, Quebec, Can. · Jul 2, 2015#99
Originally Posted by MedMantle ↑
I still have the stock intake. Like 'scod' said, just give it all you've got! :P I had to turn my stock intake pipe around to get it to fit and it was still quite tight and difficult to get over, but I eventually got it. I would have loved to be able to use a adapter like that but we have almost no aftermarket car stuff where I live. :)
You don't get the full benefit of the 1ZZ TB with a stock air intake pipe/filter and stock intake manifold. Everything is 46mm while the 1ZZ is about 55mm. I did the same as you at first but ended up installing a proper tube and filter. Next is the intake manifold and port polish the head. Only way to benefit 100%
MedMantleSouth Africa · Jul 3, 2015#100
Originally Posted by Rigaud ↑
You don't get the full benefit of the 1ZZ TB with a stock air intake pipe/filter and stock intake manifold. Everything is 46mm while the 1ZZ is about 55mm. I did the same as you at first but ended up installing a proper tube and filter. Next is the intake manifold and port polish the head. Only way to benefit 100%
Rigaud, what air intake did you use for your setup? Do you maybe have a picture? I'd imagine the ribbed stock intake pipe causes some disturbance with flow. I wanted to get an aftermarket intake (specifically the Injen CAI) mainly for eye candy.

In the future I'm gonna look at doing an engine swap to the 1.5 (yes, I am driving the 2NZ-FE 🆘 ) and once I have the engine I'm gonna do a bit of work on it like porting and stuff regardless of the gains, mainly for fun though 'cause I'm still learning. I'm happy to hear there are still potencial gains to come :D

This forum was my first introduction to how cars work so my Yaris is kinda my guinea-pig :P