Yarisworld Archive

My Dyno Run

12 posts · 9,283 views

japleOriginal postKuala Lumpur, Malaysia · Nov 12, 2014#1
guys, this is my cars dyno run... the car came as an 1.5s 1nz-fe, auto, full stock, for some reason it was equipped with a 2nz-fe intake manifold, dont ask why, i got this car used from a car dealer.

my 1st original run, 1zz-fe throttle body, 4-2-1 header, stock mid and blitz nur-spec S-Flow Exhaust, nothing else.

Picture not included in this copy

2nd run, after a lot of 4-2-1 and 4-1 debates, switched back to the 1nz-fe throttle body, after that i bought a 4-1 header, 0.2mm thick, mandrel-bent full stainless steel piping with a huge S-Flow midbox, wouldn't say its fully S-Flow, it just enters from the top in the inlet, appears middle in the outlet, both 2 inches wide, full stainless again to the rear, then the blitz nur-spec S-Flow Exhaust

Picture not included in this copy

3rd run, after that was done, i did a lot of research regarding the differences of 1nz-fe intake manifold and the 2nz-fe intake manifold, got the same responses, they are the same, not satisfied,i got myself the 1nz-fe intake manifold, plugged it in with the 1nz-fe throttle body, got myself this, a headspinner.

Picture not included in this copy

CRAZY, 14whp!

4th run, this time i did the 1nz-fe to the 1zz-fe throttlebody transplant, but noticing the difference between 46mm and 55mm, i decided to create a spacer that would downsize the hole, to create a better airflow, and i got this

Picture not included in this copy


bear in mind that all these are done without the engine management control..


more to come......

Replies 11

japleThread starterKuala Lumpur, Malaysia · Nov 12, 2014#2
sorry guys, i did not resize it for better viewing, haha..
RagnaCaTVillalba, Puerto Rico · Nov 12, 2014#3
I'm amazed great numbers... The difference has to be really noticeable when you floor it
malibuguyWestminster, MD · Nov 12, 2014#4
At first i was like...wtf...but then i read.

Nice work...still a little low...i dunno if thats gas or automatic or what but your close to where it should be

For reference mine was 107/104 with just a full exhaust...now its 105/104 (with more midrange torque) with a Tooter spacer and a short ram (power was even less with the stock airbox and the Tooter...like 103/103). My part throttle torque still amazes me
japleThread starterKuala Lumpur, Malaysia · Nov 13, 2014#5
Ragnacat: its quite noticeable...

malibuguy: yes, its quite low, its gas, automatic and i am still not impressed yet. i do get that my car is a bit shy when it comes to full throttle, it sort of going up the steps, lots of torque, then it slows, then repeats, not so much of noticeable, but its there, i can feel it, anyone experienced this kind of symptoms before?
Ryze268Antigua & Barbuda · Nov 13, 2014#6
so the 2nz intake manifold realy is crap huh?

Thanks for the post
japleThread starterKuala Lumpur, Malaysia · Nov 13, 2014#7
Its not crap, but 1nz-fe intake manifold is a recommended upgrade, based on the dyno charts..
BoostedTRDVA · Nov 13, 2014#8
if you don't mind me asking, How much did it cost to dyno your car? I would like to get my car dynoed before going turbo.
malibuguyWestminster, MD · Nov 13, 2014#9
I meant more about the quality of the gas
japleThread starterKuala Lumpur, Malaysia · Nov 14, 2014#10
its RM60 in malaysia, so roughly, 18 bucks in america
japleThread starterKuala Lumpur, Malaysia · Nov 14, 2014#11
quality of the gas is ron 95 here in malaysia
TRD SPECMalaysia · Apr 10, 2016#12
Woah another brother from malaysia!