Black_griffin6Original postAtlanta Georgia · Apr 26, 2013#1Hey everyone!
A few days ago I installed the 1zz throttle body onto my 2009 yaris liftback MT.
I wanted to write up a little review and give some tips as to how it works and how to do it right.
First off I ordered the one with the part number 030 at the end, after I had both throttle bodies off the car, I compared the 2 part numbers on them and they both end in the 030. I think this is why the one with the 030 part number is more compatible with the yaris.
Tips on install: I had to get a deep socket 10 mm socket, it helped a lot with taking the 10mm bolts off the throttle body. There are 2 sets of 10mm bolts on the top, the second set is harder to get to and is where you need the deep socket.
You also need some gasket maker. I used
Permatex Ultra copper to seal the space behind the throttle body to the stock intake manifold.
You don't NEED the high temp stuff like what I used, but it's what I had left over from when I installed my header so I just used it.
It's there to make sure your fitment is air tight.
Make sure you disconnect your battery BEFORE you start your work.
The whole job may take 1-2 hours, it took me about 2 with basic hand tools.
But during that time your ECU will reset. After you're done and have everything hooked back up, then reconnect the battery and just let the car idle, wait 10 minutes at the least, I know 10 minutes seems like a long time but it's worth it.
All those things helped me I believe. I haven't had any problem since the install.
The only cons so far are:
Very high idle when it starts cold. Not sure how high as I don't have a tach, but you can just get in and drive it and it will go away in about 30 seconds depending on how warm it is outside.
And the throttle sometimes stays open when I don't have the car in gear and I tap the gas, but it's only for about a second, like it has a delay.
This is also very rare and don't happen often.
The review:
Overall I think it did add a few ponies. I can hear my Weapon R intake a LOT more now and it seems to get up and go a lot better.
My other engine mods are:
DC sports header,
complete lightweight pulley kit,
Weapon R secret weapon intake with Ram air tube,
and custom mandrell bent 2.5" exhaust.
Definitely worth the money and time.
I did NOT do the chip swap though, and it has been fine.
I recommend it. 👍
Replies 154
cali yarisCanoga Park, CA · Apr 26, 2013#2I'm glad this worked out well -- I know you were a little concerned, but you were patient, did it right and got a good result.
why?harnett county NC · Apr 26, 2013#3So it did fit on the intake? That is cool. Good to see it can be done with minimal fuss.
tooterLos Angeles · Apr 27, 2013#4The 55mm butterfly clears the smaller 46mm bore because it's round and high enough so that the edges don't touch. Did you need to remove the stock o ring gasket? The 1ZZ will definitely give you a quicker throttle.🙂
AstromanWenatchee, WA · Apr 27, 2013#5I have the 1zz tb as well on my 2007. High idle at startup when cold is common, verified with the scan gauge. Congrats on the successful install. My mechanic did mine in under 30 minutes. A worthwhile mod!
mazillaSan Jacinto California · Apr 27, 2013#6Having spent the amount of time(over a year) running the 1zz I think the solid recommendation is a little strong. Proceed with caution is more accurate IMO...
I'm going to try it out when I go boosted or feel particularly bored, having just gone back from the 1zz I can say I don't feel like I'm missing anything except a little top end.
tooterLos Angeles · Apr 27, 2013#7 Originally Posted by
mazilla ↑ Having spent the amount of time(over a year) running the 1zz I think the solid recommendation is a little strong. Proceed with caution is more accurate IMO...
I'm sure that's true with a stock manifold because it's only designed to handle the flow of a 46mm throttle body. But it's a whole different story when the 1ZZ is mated up to a manifold that's large enough to handle its flow capabilities.
mazillaSan Jacinto California · Apr 27, 2013#8 Originally Posted by
tooter ↑ I'm sure that's true with a stock manifold because it's only designed to handle the flow of a 46mm throttle body. But it's a whole different story when the 1ZZ is mated up to a manifold that's large enough to handle its flow capabilities.
I've had it on both, although admittedly I didn't run it more than 24 hrs in the new manifold...
tooterLos Angeles · Apr 28, 2013#9 Originally Posted by
mazilla ↑ I've had it on both, although admittedly I didn't run it more than 24 hrs in the new manifold...
Why did you go back to the 1nz? I'd never want to give up the improved throttle response.
thefallsSunny place · Apr 28, 2013#10Hi,can you share the full part number.
Thanks.
Edit* Found it.
22030-0D030
Black_griffin6Thread starterAtlanta Georgia · Apr 28, 2013#11 Originally Posted by
cali yaris ↑ I'm glad this worked out well -- I know you were a little concerned, but you were patient, did it right and got a good result.
I was very concerned. All the mods i've done so far have never given me any bad results. I do weeks, sometimes months of research about a mod before I do it, but in the end you don't really know what will happen until you do it. 😁
Originally Posted by
why? ↑ So it did fit on the intake? That is cool. Good to see it can be done with minimal fuss.
Yeah it fits the intake.
The intake I have came with a rubber adapter that shrinks down the size of the rubber connector, I simply removed it and used the same rubber connecter it came with.
Originally Posted by
tooter ↑ The 55mm butterfly clears the smaller 46mm bore because it's round and high enough so that the edges don't touch. Did you need to remove the stock o ring gasket? The 1ZZ will definitely give you a quicker throttle.🙂
Not sure where the o-ring gasket it. It is behind the throttle body where the TB connects to the manifold?
If so, I did not remove that.
Originally Posted by
mazilla ↑ Having spent the amount of time(over a year) running the 1zz I think the solid recommendation is a little strong. Proceed with caution is more accurate IMO...
I know it hasn't worked with everyone. But I think it's a worthwhile thing to at least try.
I'm not sure how it will work out boosted, I don't know of anyone that has tried it yet.
HANZO_187Wintergarden, FL · Feb 7, 2014#12I'm gonna give it a shot. Where'd you get the resources on how to install it properly? You have some mechanic skill or you just winged it?
ilikericesavannah, ga · Feb 7, 2014#13It's super easy. I will say, the thing that the OP missed was the coolant lines. I had to swap them because of the location of the inlet and outlet of the 1zz throttle body compared to the 1nz. It worked out fine though.
If its your first time, I recommend taking pictures with your phone before and thru the process of it. Just so you will have a reference to look back on if you happen to forget what went where.
tooterLos Angeles · Feb 7, 2014#14It's a pretty straightforward swap. The stud holes are exactly the same. While you will need longer liquid heating hoses to reach the fittings...
Picture not included in this copy
I recommend gently chipping away the epoxy from around the tiny allen head screw that controls the butterfly idle stop. Then you can turn it town about a turn until you get a nice slow hot idle.
Picture not included in this copy
The high cold start idle will remain the same at about 2,000 rpm because that's determined by the ECU. But it drops down to normal really fast especially if you reset the hot idle down low.
Remember that the opening in your manifold is still the same diameter so maximum flow is restricted. However, you will definitely have better throttle response, as the larger butterfly opens wider quicker. Make sure you use an allen wrench that fits very tightly. You do not want to strip the head of that tiny screw.
The properly sized silicone adaptor will allow the 1ZZ throttle body to accept just about any aftermarket intake. You can also see the location of the tiny idle adjustment screw at the center top of the photo.
Picture not included in this copy
Greg
HANZO_187Wintergarden, FL · Feb 7, 2014#15I'm really wanting to take this on. Ok, so the hoses where can you get longer ones at? I also have a Cosmic Racing CAI and working on getting after-market headers (Megan, DC) wondering if it will still fit to everything proper but this is down the line.
I wanna squeeze as much info I can before going into this but it seems pretty straight forward. Gonna get a BLOX adapter just in case...better to have it and not need it then need it and not have it. appreciate the 101 guys.
I got my first Auto X coming up in march and I'd like to squeeze what ever I can out before hand.
tk-421Dagobah · Feb 8, 2014#16I also did this mod and recommend it for sure. I had to modify the OEM hose slightly by removing a very thin layer of rubber with a dremel. No biggie and worked like a charm and did a coolant bypass with a copper joint.
I also have a high idle for around 60 sec or so. I've had it that way for many years and I've had zero problems, FWIW.
@HANZO_187: There's a couple of very good threads about this info. Just keep in mind that some 1zz tb's work without having to swap chips (located at the base), while others apparently require it. I did it in about 10 min (maybe less) by using a drill with a very narrow bit (so that it only destroys the rivets and nothing else). HTH
ilikericesavannah, ga · Feb 8, 2014#17 Originally Posted by
tk-421 ↑ I also did this mod and recommend it for sure. I had to modify the OEM hose slightly by removing a very thin layer of rubber with a dremel. No biggie and worked like a charm and did a coolant bypass with a copper joint.
I also have a high idle for around 60 min or so. I've had it that way for many years and I've had zero problems, FWIW.
@HANZO_187: There's a couple of very good threads about this info. Just keep in mind that some 1zz tb's work without having to swap chips (located at the base), while others apparently require it. I did it in about 10 min (maybe less) by using a drill with a very narrow bit (so that it only destroys the rivets and nothing else). HTH
you mean 60 seconds right?
As far as the hose go, you can use the hoses that are on the car, just swap them around. Make sure you have a pan under the car to catch the coolant when you pull the hoses off. you can use a used spark plug to plug the hose when you disconnect them from the throttle body and try to be fast. If your not fast enough, its going to get messy.. lol, but its not a big deal at all. I just zip tied them together to keep them away from the shifter cables
Now, on the stock manifold, I measured the rubber "O" ring on the mani-throttle body. I did not have to make a gasket. The 1zz throttle body fit just right where it sealed up with the throttle body. It was close, but I did not have an issue with any leaks. I used the existing O ring on the manifold. 🤷
HANZO_187Wintergarden, FL · Feb 8, 2014#18Ok cool, I'm getting the ideal process for this now. My other question now is do we know if what main years the 1zz TB come off of? I know a Toyota Matrix has it but not sure if any other cars and years.
1.5Tampa · Feb 8, 2014#19Han I still have mine sitting in my trunk waiting to install. We can do them together when you get one
tk-421Dagobah · Feb 8, 2014#20 Originally Posted by
ilikerice ↑ you mean 60 seconds right?
Yes, yes I do. 🙄
tooterLos Angeles · Feb 8, 2014#21 Originally Posted by
HANZO_187 ↑ I'm really wanting to take this on. Ok, so the hoses where can you get longer ones at? I also have a Cosmic Racing CAI and working on getting after-market headers (Megan, DC) wondering if it will still fit to everything proper but this is down the line.
I wanna squeeze as much info I can before going into this but it seems pretty straight forward. Gonna get a BLOX adapter just in case...better to have it and not need it then need it and not have it. appreciate the 101 guys.
That BLOX coupling just came with the BLOX velocity stack air filter...
Picture not included in this copy Picture not included in this copy ...and isn't special. Any properly sized silicone coupling will do.
I got my first Auto X coming up in march and I'd like to squeeze what ever I can out before hand.
Check to see if they allow running a larger throttle body without having to change the class you're running in. Or... maybe they won't notice.
Greg
1.5Tampa · Feb 8, 2014#22Han your local autozone/discount/whatever will carry an assortment of those couplings
cali yarisCanoga Park, CA · Feb 8, 2014#23^ Just go by the part number. Car model years are not a predictable way.
ilikericesavannah, ga · Feb 8, 2014#24 I got my first Auto X coming up in march and I'd like to squeeze what ever I can out before hand.
If you are doing an SCCA event, larger throttle body will throw you in FSP "F Street Prepared" I don't know all the modifications you have done, but if you list them, we can help you class your car.
1.5Tampa · Feb 8, 2014#25with lowering springs i think youll be in STF but like Derrick says the TB will put you into SMF (iirc)
HANZO_187Wintergarden, FL · Feb 8, 2014#26Heres what got listed in the car so far.
Sprint progressive lowering springs
Cosmic Racing CAI
NST 10% Crankpulley
Rear Seats removed
Thats what I got as of now, I also got Megan Headers that I might be buying from "BUZZ" and I don't know if
Wheels play a part in this but was going to buy KONIG Flatout wheels 15x8 at 12 lbs each. Just putting it out there in case it counts and @1.5 yeah bro count me in, give me a reason to come hang and check out your car. Lol
yariseggvvtiCali · Feb 8, 2014#27How's the sounds like when you run 2.5" exhaust? Did you delete resonator and second CAT? Do you lose any lower end and getting more high end. VVTI kicks harder?
Thanks!
CrankyOldManWest Michigan · Feb 8, 2014#28Throttle body:
STF: 14.10.C The air intake system up to, but not including, the engine inlet may be
modified or replaced. The engine inlet is the throttle body, carburetor,
compressor inlet, or intake manifold, whichever comes first.
FSP: 15.10.C. Induction allowances are as follows:
1. Carburetors, fuel injection, and intake manifolds are unrestricted...
SMF: 61.1.D. Drivetrain and related components (induction, ignition, fuel systems,
etc.) are unrestricted...
Crank pulley:
STF: 14.10.H. Any accessory pulleys and belts of the same type (e.g., V-belt, serpentine)
as standard may be used. This allowance applies to accessory
pulleys only (e.g., alternator, water pump, power steering
pump, and crankshaft drive pulleys). It does not allow replacement,
modification, or substitution of pulleys, cogs, gears, or belts which
are part of cam, layshaft, or ignition drive or timing systems, etc.
Any crankshaft damper or pulley may be used. SFI-rated dampers
are recommended.
Rear seats removed:
FSP: 15.2.F. Cars may have no fewer than the standard number of seats.
SMF: 16.3.K. Rear passenger seat(s), including restraints and associated hardware
may be removed.
Looks like you're running SMF this year. =)
cali yarisCanoga Park, CA · Feb 8, 2014#29^ I ran SMF. It's not possible to be competitive in the Yaris in that class.
HANZO_187Wintergarden, FL · Feb 8, 2014#30Ok so with me having my rear seats out a I'm running SMF then?
If get headers added to the list its gonna keep me there am ai right?
I'm not gonna get the TB for now since its gonna be putting me in a class I can't even compete against.
BUT I am gonna get it just in case...lol Just having it on hand is good.
CrankyOldManWest Michigan · Feb 8, 2014#31I'm only competitive against the one other regular SMF car in my region--a Cobalt SS with a pulley change. Neither of us built our cars around the SMF rules, that's just where we ended up. When a national competitive SMF car shows up, it's game over. That doesn't mean I don't have an incredible amount of fun in the mean time.
cali yarisCanoga Park, CA · Feb 8, 2014#32^ understood -- I had a blast too, but when 30 serious SMF cars show up, it's pretty humbling.
HANZO_187Wintergarden, FL · Feb 8, 2014#33I'm pretty happy about going into this...I like how this throttle body thread went into an Auto Cross thread. lol
Naw but I seriously respect you guys for the info and for what you guys do.
I'm really looking forward to this and I hope some where along the silver lining I get a drivers edge out of it. I always loved racing as a youngster and with being the second Yaris I think besides Buzz that will be doing Auto X I'm just hopeful to get some good times in and show people that a few of us Yaris drivers mean buisness.
March 9th man...I can't get my mind off of it.
ilikericesavannah, ga · Feb 9, 2014#34They guys in our region are anal about modification. Gino who is running Garm's Yaris is actually running XP class. With the interior gutted out he is technically in a Prepared class.
Can't run in EP because of the turbo. lol
Also, body kits and fiberglass hood will throw you in SMF. Unless its from the Yaris S. I have those rubber quick disconnects and would swap out my front and rear bumper and take off my side skirts at each event to stay in STF. That was before the 1zz throttle body and catless exhaust.
So, keep the interior in, if you are just removing the rear seats. SMF is fun. I am running SMF also this year, mod list are:
Megan coilovers
Megan Headers
Nitto catless mid pipe*
Tenabe axle back
1zz throttle body
CAI
Body kit*
15x7 rota gt3
225/45 Hankook RS3
* is the mods that put me in SMF
I now take my rear seat out before an event also to help with weight. Damn things are heavy as shit too..
RednazCape Town, RSA · Feb 9, 2014#35Will the 1zz throttles work on the 2NZ 1300 engines as well?
HANZO_187Wintergarden, FL · Feb 9, 2014#36@ilikerice I gotta check out what there rules are, I'm getting a lot of good mods for some LOW prices so modding is not so bad when I have spent less then 400$ for all the mods I have so far (Counting my HID's and Aftermarket alarm system) along with Megan headers coming into play before my first run.
I'm gonna be looking into wheels and stickier tires soon along with some bracing soon after but I am ALWAYS trying to get used parts and cheap prices on parts.
Kinda the reason why I call my Toyota the "V1" Standing for Vulture1. Hope you get the idea.
tooterLos Angeles · Feb 9, 2014#37 Originally Posted by
Rednaz ↑ Will the 1zz throttles work on the 2NZ 1300 engines as well?
I don't think that 1ZZ would offer any other benefit except that your accelerator would more sensitive to input. Remember it is just a valve that lets air into the engine. When I dyno tested mine on a 1.5, while it did make some gains at the top end and some slight improvement on the way up, at low rpms there was no difference except that because it was larger it let more air in quicker. So the throttle is more responsive. That's the main improvement.
Can you post a pic of your intake? Also is your throttle body electronically actuated, or is it cable operated? We might be able to determine if it would work.
Greg
cali yarisCanoga Park, CA · Feb 9, 2014#38 So the throttle is more responsive. That's the main improvement.
Just as easily replicated with a throttle controller then!
ilikericesavannah, ga · Feb 9, 2014#39 I gotta check out what there rules are
Yea man. Since you are modding just for fun and not for a specific class, just have fun with your car. Stick to SMF. Its fun when you are kicking the B swapped civics and turbo Integra's. If you got any questions on mods you are about to buy and curious about class, feel free to PM me. I am taking the chairman spot this year at our region so I gotta be on top of these kinda things
Black_griffin6Thread starterAtlanta Georgia · Feb 9, 2014#40 Originally Posted by
yariseggvvti ↑ How's the sounds like when you run 2.5" exhaust? Did you delete resonator and second CAT? Do you lose any lower end and getting more high end. VVTI kicks harder?
Thanks!
It sounds pretty awesome man, I'll post a couple of videos when I get the chance.
Yes, resonator and secondary cat are gone.
Below 3 grand, you would think it was a much bigger engine, above that it kinda sounds like a 240sx, really mean sounding.
I think a turbo or supercharger would really help, this is a FI exhaust on a NA car. Right now it doesn't pull as hard as I think it's capable of, it's only making about 100 whp.
yariseggvvtiCali · Feb 10, 2014#41dose it sounds really deep or ricy? If you have time, post a video please. thank you!
JimKellyfanthe good Carolina · Feb 12, 2014#42Yeah, that is why I am focusing on the handling. Years ago, the old roundish jaguar XKE back in the early 60's got beat bad due to lack of power. The next year, they came out with better braking and beat em all in the turns. The handling and braking would have to be our edge. I put a bunch of bars on for stability, and it is rail like, even with the T rated tires, which I will swap them when worn to V rated Michelins (195/60/15). But, I am thinking of going to add even more bars from Ultra racing, the ones I don't have yet, 3 point fender brace, rear torsion bar, side lower and room bars. Good luck racing this year.
ilikericesavannah, ga · Feb 12, 2014#43Tires, get some better tires.. You wanna ride on rails with a yaris, go wider, 195 are a bit skinny and the Michelins last longer but they just dont grip like the Falken 615k, Toyo R1R, Hankook RS3's..
CrankyOldManWest Michigan · Feb 12, 2014#44I thought the magic number for R1R's was 195/50R15, no? Aside from that, go as wide as your fenders allow.
ilikericesavannah, ga · Feb 12, 2014#45If you wanna ride on rails, get thw Hoosier A6 in 275.
Everything you said is correct cranky
HANZO_187Wintergarden, FL · Feb 12, 2014#46I was looking at those wheels just now, not bad on the prices (IMO atleast)
I'm hoping to get some nice and sticky tires down the line but for now I need to get some new and lighter wheels and some decent tires to put em on. One pair for street use and the other for track buisness.
Btw guys thank you for helping us guys out with all the knowledge, glad to be part of this.
salmanghiyasPakistan · Jul 19, 2014#47sorry for reviving this old thread 😛
and thousand sorries in advance ... as i will be prompting and asking anything which i cud not understand you all guys at YW 😁 im new to YW and just bought a 2008 yaris 1.5L manual tranny ... and now a days just spending my spare time on YW forums and google ... reading and understanding NA mods ... i am trying my level best to get as much as i can .. but still .. im a newbie 😳 ... so had to ask questions ..sorry if i sound stupid 😢
my question is ... here the swap is in between electronic TB's ? the ones which are DBW ?
japleKuala Lumpur, Malaysia · Nov 11, 2014#48Its for the electronic tbs.... for the cables, if not mistaken, it also a direct swap...
mattymoGA · Dec 17, 2014#49All, tb swap is kicking my butt. I've tried everything...chip swap, dial in good idle while warm after battery cycle, but i still get P0505 idle control system code. It also jerks sometimes letting on and off the throttle. Does anyone think i should adjust other stop screw inside the tb? This looks like it sets how far back the valve can close. It looks like the ecu can actually fully shut the valve the way it's set now. Does the ecu actually do this? Any suggestions? Preeshiate it. Car runs great under this mod when it's cooperating, but flakes into this code.
Sent from my GT-P5210 using Tapatalk
tooterLos Angeles · Dec 18, 2014#50 Originally Posted by
mattymo ↑ All, tb swap is kicking my butt. I've tried everything...chip swap, dial in good idle while warm after battery cycle, but i still get P0505 idle control system code. It also jerks sometimes letting on and off the throttle. Does anyone think i should adjust other stop screw inside the tb? This looks like it sets how far back the valve can close. It looks like the ecu can actually fully shut the valve the way it's set now. Does the ecu actually do this? Any suggestions? Preeshiate it. Car runs great under this mod when it's cooperating, but flakes into this code.
Sent from my GT-P5210 using Tapatalk
The symptoms you're describing are exactly what I experienced before turning out the tiny factory epoxied external hex head screw to allow the butterfly to come to rest at a more closed position. That one adjustment solved everything.
Check that the butterfly isn't hanging up on anything
under the throttle body. That could also prevent the butterfly from closing.
Check and recheck everything for any air leaks. They can play havoc with the idle. And make certain that all of the vacuum hoses to your intake manifold are going to the original factory locations.
What kind of intake and filter are you running? Check for any air leakage around the MAF, as well as the electrical connection at the plug, as it determines your A/F at idle.
Greg