Yarisworld Archive

My 2011 Vitz

655 posts · 261,587 views · page 10 of 14

Replies continued

TerenceCruzThread starterCali · Aug 25, 2015#451
Originally Posted by coheed ↑
Don't get me wrong, I like the control I have over my height. I just wish I could pin down my leaking lol. Also I wish it aired out a little bit quicker. The exhaust port on the manual valves are 1/8" and it takes so long for the front to go down. And I run twice the air in the front as the rear, so the back of the car is down 5 sec before the front.

I'm liking the 16's on your car more and more man. You're convincing me that static Yarii need 16's.
Ahhh very true, my friend said the same, we parked in the garage and I was like what're you doing, and he said "Still airing out" hahaha it was hella funny. The port can't go any bigger? And thanks a lot man, I feel the same way. I'm just looking towards a different type of wheel now. Still 16s, maybe 16x9 but I'm just over the mesh look haha.
yarisugiハワイ · Aug 26, 2015#452
@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising.

@TC- New wheels already? Curious what you have in mind...
coheedMaiden, NC · Aug 26, 2015#453
Originally Posted by TerenceCruz ↑
Ahhh very true, my friend said the same, we parked in the garage and I was like what're you doing, and he said "Still airing out" hahaha it was hella funny. The port can't go any bigger? And thanks a lot man, I feel the same way. I'm just looking towards a different type of wheel now. Still 16s, maybe 16x9 but I'm just over the mesh look haha.
I don't know if it could go any bigger. I would try drilling it out a bit, but at $15 and not being able to buy one locally, I think I'll leave it and deal with airing out slowly lol
Originally Posted by yarisugi ↑
@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising.

@TC- New wheels already? Curious what you have in mind...
No my lines are 1/4", but the air exhaust port on the back of the manual paddle valves are 1/8". My raise time is great, its the lowering that takes forever.
TerenceCruzThread starterCali · Aug 26, 2015#454
Originally Posted by yarisugi ↑
@coheed - 1/8" lines are tiny! After you find your leak, try 1/4" at least. Not more than 3/8" though. Should help speed up your lowering/raising.

@TC- New wheels already? Curious what you have in mind...
I was trying to avoid the mesh look, but I got a good offer for a trade for some brand new 16x9s so i'll post on here with pics if it goes through! Polished lips with white faces :) Still reps unfortunately, but ill fake the funk til i graduate school and get something nicer :)
TerenceCruzThread starterCali · Sep 6, 2015#455
Trade didn't go through, but I ended up finding some other JNCs in 16x9 that I loved. They will be arriving in a few days, and I'll mount the same tires I had on the BBS RS reps. Since they will be 16x9 I think the 195/45s will be the perfect stretch. Pics will be up when I get them on! :)
TerenceCruzThread starterCali · Sep 11, 2015#456
As promised. New wheels are on! 16x9 +25 JNC014 (Sorry they're still reps lol but I love them) on 195/45s. I have 10mm spacers in the rear. So +15 in the rear :) Hate how it looks high from the rear. Lol. There are some rubbing issues, so I will have to pull/flare the fenders out even more.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
coheedMaiden, NC · Sep 12, 2015#457
Seriously it looks awesome man. Props.

And you'll never get over thinking the Yaris looks high in the rear. I think mine looks high in the rear aired out lol
TerenceCruzThread starterCali · Sep 12, 2015#458
Originally Posted by coheed ↑
Seriously it looks awesome man. Props.

And you'll never get over thinking the Yaris looks high in the rear. I think mine looks high in the rear aired out lol
Much love bro, thank you! And lol that's so irritating. Can they make a rear lip or something easier to get.. Smh haha.
TerenceCruzThread starterCali · Sep 12, 2015#459
More pictures with the homies recently acquired EG8 while he works on his GSR 4 door.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

Still scraping pretty tough, probably gona add a tad bit more camber in the front. I love how she sits though!
ern-dizCA all day · Sep 14, 2015#460
Super clean
TerenceCruzThread starterCali · Sep 14, 2015#461
Originally Posted by ern-diz ↑
Super clean
Thanks man!
Supra_YarisDenton, TX · Oct 27, 2015#462
How many washers did you you to achieve that much rear camber? And about how many degrees of camber do you have in the rear?
TerenceCruzThread starterCali · Oct 27, 2015#463
Originally Posted by Supra_Yaris ↑
How many washers did you you to achieve that much rear camber? And about how many degrees of camber do you have in the rear?
Used 3 grade 8 washers per lower bolt on each side. So i have a total of 12 washers. I'm running about -3 camber. Each washer used is supposed to be -1 degree of camber.
Supra_YarisDenton, TX · Oct 27, 2015#464
Originally Posted by TerenceCruz ↑
Used 3 grade 8 washers per lower bolt on each side. So i have a total of 12 washers. I'm running about -3 camber. Each washer used is supposed to be -1 degree of camber.
Great! Just what I was looking for. Thanks!
asproToronto, Canada · Oct 27, 2015#465
This car is stupid, retarded shlammed.... I love it haha
asproToronto, Canada · Oct 27, 2015#466
Also, if youre looking to get the rear end lower to the ground, why dont you source a rear toyota RS lip for the 09-11 yaris'... That mkght get you a few more inches to the ground without have to go lower. Heres what the lip looks like...

Picture not included in this copy
TerenceCruzThread starterCali · Oct 28, 2015#467
Originally Posted by Supra_Yaris ↑
Great! Just what I was looking for. Thanks!
No worries man!

Originally Posted by aspro ↑
This car is stupid, retarded shlammed.... I love it haha
Hahaha thanks man! Im also looking for the whole kit actually. I want to source a front, rear, and side skirts. I'd love to find it.
TerenceCruzThread starterCali · Nov 2, 2015#468
Aspro, I also want your exhaust so bad haha. I would trade cars with you instantly hahaha.
asproToronto, Canada · Nov 3, 2015#469
Haha, thanks man! Its the trd exhaust, im sure you can still get your hands on one! If i ever decide to sell, i will let you know first :p
TerenceCruzThread starterCali · Nov 3, 2015#470
Originally Posted by aspro ↑
Haha, thanks man! Its the trd exhaust, im sure you can still get your hands on one! If i ever decide to sell, i will let you know first :p
Just an axle back right? I've been looking :( And yes PLEASE hahaha.
TerenceCruzThread starterCali · Jan 12, 2016#471
Hey guys, haven't posted on here in a while. I started my medical program so I've been really busy. I actually raised the car a tad bit, and removed the front HD lip since it was torn up haha. The washers I used to achieve my negative camber in the rear caused excessive toe problems and I burned through my rear tires as soon as I started to commute to school. So, I decided to pull the trigger on some -3 camber shims from realcamber.com :) Since I just recently found out they almost 0 out toe! Here are some pictures of her current ride height.

Picture not included in this copy12498490_889578174484331_1809454124_n by Tj Cruz, on Flickr
Picture not included in this copy12511788_889578157817666_1573389995_n by Tj Cruz, on Flickr
Picture not included in this copy12528079_889587997816682_919627008_n by Tj Cruz, on Flickr

I guess most people still consider this low, but compared to before she feels like a tonka truck now hahaha. Greatest thing ever is I BARELY rub at all now, even with 3 people in the car with me. But yes, next on the list is some new rear tires, and an axle back exhaust! As soon as I get the rear camber shims installed I will drop her back down.
ern-dizCA all day · Jan 12, 2016#472
Looking sharp, as always!
TerenceCruzThread starterCali · Jan 12, 2016#473
Originally Posted by ern-diz ↑
Looking sharp, as always!
Thanks man I appreciate it! It needs some nice sound though, it's too quiet :( Haha.
bgkz25Auckland · Jan 13, 2016#474
Good looking car!
(I can't help but noticed that you park the same way as I am. End spot and close to the curb as possible so that I'll just have to worry about one side of the car being dented by an oblivious driver when they carelessly open their doors.)😃
ern-dizCA all day · Jan 13, 2016#475
Originally Posted by bgkz25 ↑
Good looking car!
(I can't help but noticed that you park the same way as I am. End spot and close to the curb as possible so that I'll just have to worry about one side of the car being dented by an oblivious driver when they carelessly open their doors.)😃
So true lol
TerenceCruzThread starterCali · Jan 13, 2016#476
Originally Posted by bgkz25 ↑
Good looking car!
(I can't help but noticed that you park the same way as I am. End spot and close to the curb as possible so that I'll just have to worry about one side of the car being dented by an oblivious driver when they carelessly open their doors.)😃
Originally Posted by ern-diz ↑
So true lol
You guys are very correct! Haha. No matter how small our cars are someone will find a way to hit it.. I have a nasty dent in my rear driver side quarter panel because someone dinged it at the mall.. Horrible people. It's not going to be cheap to fix either.
TerenceCruzThread starterCali · Jan 14, 2016#477
-3 camber shims and extended hub bolts should both arrive by Saturday :) Can't wait to install them so I can drop the rear back down to even it out the rake, as well as not have to worry about burning through rear tires! I actually love how the front sits, if anything I'll drop it back down another half inch or so. So excited. Also talking to a member on here for a TRD axle back that I've been searching for so I hope things work out. If it does, 2016 is off to a good start! :D
TerenceCruzThread starterCali · Jan 14, 2016#478
Also, just wanted to reminisce a little bit. I kind of miss this set up:

Picture not included in this copy0ctuHdf by Tj Cruz, on Flickr
Picture not included in this copy20150716_202702 by Tj Cruz, on Flickr
Picture not included in this copy20150621_172552 by Tj Cruz, on Flickr

And riding this low :( Although in order to get that low in the front I had to drop preload a little bit which caused it to not ride as well.. I hate how I can't turn the shock body more to lower the front end the right way, as it is close to my axle already.. -__-

Picture not included in this copy20150910_170926 by Tj Cruz, on Flickr

I also plan on getting the body damaged fixed this year so I hope it all goes according to plan :) ABS and VSC is still disabled for some reason.. I know I have a bad speed sensor somewhere but my speedometer is still accurate. Weird.
FreestylinCalgary, Alberta · Jan 14, 2016#479
Looking good! Hope everything works out for you with the body damage. There is a reason why I park miles away from the rest of the general public.. haha. People will still find a way to ding ya regardless of where you park.. :(
TerenceCruzThread starterCali · Jan 14, 2016#480
Originally Posted by Freestylin ↑
Looking good! Hope everything works out for you with the body damage. There is a reason why I park miles away from the rest of the general public.. haha. People will still find a way to ding ya regardless of where you park.. :(
Thanks a lot Freestylin! Yeah I haven't really had it happen to me. I trusted people (for the most part) to maybe even leave a note if anything were to happen, but no.. So I have now learned my lesson. Once I get the damage fixed I will be the guy who parks all the way at the end of the lot hahaha.
TerenceCruzThread starterCali · Jan 16, 2016#481
-3 realcamber shims are on! I can definitely see how much toe was corrected! Will still have to see for sure after I get new rear tires and take her to get an alignment. High quality product, and I'm so glad I don't have washers under my hubs anymore haha! I also lowered the rear a bit more too.. No more rake ;)

Picture not included in this copy12584096_891803527595129_702379605_n by Tj Cruz, on Flickr
Picture not included in this copy12575886_891757944266354_1707719214_n by Tj Cruz, on Flickr
TerenceCruzThread starterCali · Jan 18, 2016#482
Picture not included in this copy
Picture not included in this copy

Ahh Yarisworld, today is a sad day because I finally decided that I will be parting out my car.. Not selling the car, but she will be close to stock. I really need to just have a solid commuter for school. So, I decided to use the Yaris for what I originally bought it for, to be a great commuter with no headaches. Get me to point A to B with not having to worry about camber wear or being limited to where to go. So, I have a few people interested in some parts already, but here's everything that I have for sale just in case people back out. Will not be shipping anything out so this will be for anyone local in Northern Cali. I will start putting the car to stock ASAP.

Megan Racing coilovers (no dampening adjustment knobs, but they can be adjusted with the right size allen key) - $600 (Would gladly offer a discount in exchange for stock struts with lowering springs) (These are already pending for stock struts + Tein springs + $500 cash)

6" 10k and 5" 8k Swift springs (Less than 1k miles on them) - $250 for both.

22mm Whiteline adjustable rear sway bar - $150

10mm PG hubcentric spacers + extended hub bolts - $50

Scion FRS Pioneer headunit (PT546-00130 Bluetooth/HD radio compatible) - $100

-3 RealCamber shims + extended hub bolts. (I JUST BOUGHT THESE lol had to buy them separately too so I'm definitely not making any profit lol) These are great though, at the height I'm at I definitely saw right away how much it corrected my toe - $160

16x9 JNC 014 +25 wrapped in 195/45R16 Achilles ATR Sport Tires (Would be willing to trade for some wheels plus cash on your end) - $500

If you are in Northern Cali please shoot me a text if you're interested in anything. Thanks guys!

Terence
(925)301-5873
WeeYariGeorgetown, Ontario, Canada · Jan 18, 2016#483
An epic thread coming to an end.
ern-dizCA all day · Jan 18, 2016#484
👍
TerenceCruzThread starterCali · Jan 18, 2016#485
Originally Posted by WeeYari ↑
An epic thread coming to an end.
Sad to say it, but yes man ;(

Originally Posted by ern-diz ↑
👍
I'll be back in the car game soon enough 👍
TerenceCruzThread starterCali · Jan 18, 2016#486
A bunch of friends texted me not to part the Yaris out.. Pretty cool considering they drive bagged Si's, bagged Subarus, but they still love my little Yaris :D hahaha. So, I'll take a bit more time to decide whether she is parted out or not.. Thanks fellas!
coheedMaiden, NC · Jan 20, 2016#487
Seriously consider keeping it the way it is man. I regret taking mine back to stock. Don't get me wrong, it's a wonderful commuter, but man do I miss being bagged. Yours is one of the nicest on here in my opinion. Will be sad to another one go.
tadakunOregon · Jan 21, 2016#488
I'm glad you are considering keeping it...honestly. we need more like this around.
TerenceCruzThread starterCali · Jan 21, 2016#489
Originally Posted by coheed ↑
Seriously consider keeping it the way it is man. I regret taking mine back to stock. Don't get me wrong, it's a wonderful commuter, but man do I miss being bagged. Yours is one of the nicest on here in my opinion. Will be sad to another one go.
Originally Posted by tadakun ↑
I'm glad you are considering keeping it...honestly. we need more like this around.
Thanks so much for the positive words guys, I was losing motivation for her at first, but no sir, definitely not anymore. I'm happy to say that this build will continue, and it is far from over! 👍
WeeYariGeorgetown, Ontario, Canada · Jan 21, 2016#490
I retract post #488
ern-dizCA all day · Jan 21, 2016#491
🤘👏
bgkz25Auckland · Jan 21, 2016#492
👍cool move. All the hard work done, you've already come this far might as well just carry-on.
tadakunOregon · Jan 21, 2016#493
👍👍

You know, if you were getting burned out because the struggle of the low life ,then the obvious solution is baaaaaaaaggggggggssssssssssssssssssssss.😈
tmontagueCaledonia Ont. · Jan 21, 2016#494
Glad you're keeping your ride as is, it's a nice looking car
TerenceCruzThread starterCali · Jan 22, 2016#495
Originally Posted by WeeYari ↑
I retract post #488
Hahaha sorry WeeYari 😁

Originally Posted by ern-diz ↑
🤘👏
🤣🤣

Originally Posted by bgkz25 ↑
👍cool move. All the hard work done, you've already come this far might as well just carry-on.
Thanks a lot man I appreciate it. Yes this car will never be done, but really what car ever is? That's the fun of a project car. Can't wait to get more parts for her.

Originally Posted by tadakun ↑
👍👍

You know, if you were getting burned out because the struggle of the low life ,then the obvious solution is baaaaaaaaggggggggssssssssssssssssssssss.😈
Hahaha although I'm not opposed to bags at all, strictly static for this car 🤘

Originally Posted by tmontague ↑
Glad you're keeping your ride as is, it's a nice looking car
Thank you man I appreciate it! Much more to come in the future!
tadakunOregon · Jan 22, 2016#496
Originally Posted by TerenceCruz ↑

Hahaha although I'm not opposed to bags at all, strictly static for this car 🤘
haha fair enough.

hey I know these cars have the back wheels that are offset slightly from side to side. Do you know what the difference is from side to side? like if i wanted to get the poke equal on both side?
yarisugiハワイ · Jan 22, 2016#497
@tadakun - here you go (link). Around 3-4mm

@TerenceCruz - Glad you're keeping it after putting all that effort. Watch those speedbumps and potholes. :)
tadakunOregon · Jan 22, 2016#498
Originally Posted by yarisugi ↑
@tadakun - here you go (link). Around 3-4mm
great thanks man!
TerenceCruzThread starterCali · Jan 22, 2016#499
Originally Posted by tadakun ↑
haha fair enough.

hey I know these cars have the back wheels that are offset slightly from side to side. Do you know what the difference is from side to side? like if i wanted to get the poke equal on both side?
That's right, due to the crooked torsion beam in the rear, I was told 3mm-5mm spacer on the rear drivers side should do the trick. In my experience the 5mm poked out slightly more than I needed it to, so I purchased a 3mm spacer and that should be arriving within a couple of days. I think it'll be more even so we'll see. As soon as I install the spacer I will post a pic!
tadakunOregon · Jan 24, 2016#500
Originally Posted by TerenceCruz ↑
That's right, due to the crooked torsion beam in the rear, I was told 3mm-5mm spacer on the rear drivers side should do the trick. In my experience the 5mm poked out slightly more than I needed it to, so I purchased a 3mm spacer and that should be arriving within a couple of days. I think it'll be more even so we'll see. As soon as I install the spacer I will post a pic!
Ah ok ok keep me updated. My buddy hooked me up with a guy in SoCal I think that supplied his custom spacers for he AVante Gardes. I'll def get some custom hub centric spacers shortly.