Yarisworld Archive

Limits of stock 1nzfe found once and for all.

167 posts · 63,684 views · page 1 of 4

pimp my yarisOriginal postchicago · Apr 29, 2012#1
This is my motor with bent rod and cracked block and piston sleeve. This was at 12psi and 197whp dynoed only 2 days before major engine noise on a mustang dyno. Now on to the build of my junk jard motor. 🤷

2 attachments not included in this copy

Replies 166

JumpmanYarisSO. INDIANA · Apr 29, 2012#2
Ouch
YodaFL · Apr 29, 2012#3
Told ya the rods where the first to go lol. Thanks to for getting that Dyno. Be sure to add your info to my durability thread when u get a chance. You pushed it further than i did by 2 psi. At 10psi after awhile I burnt up my valves. How are yours?
Focus_Sh1ftNew Jersey · Apr 30, 2012#4
Wow. I'll keep the innuendos to myself.

Looking forward to watching your rebuild. Thanks again - this is a vital piece of information for those of us with boost.
eTiMaGoBangkok, Thailand · Apr 30, 2012#5
hmmm Gonzo rods :D Sorry to hear that dude, but now we have a better idea of the limitations of the stock hardware :)
fnkngrvIn The Hotbox · Apr 30, 2012#6
It has become obvious that 8psi is the max safe boost level with considerations of even staying at 6 for those folks that are looking for longevity and reliability. Personally in hindsight with my build I wouldn't tell anyone to use an internal wastegate unless they installed a premium turbo. I would also sttrongly recommend performing a compression test before and then again after installation.
fnkngrvIn The Hotbox · Apr 30, 2012#7
I wish that I could reinforce your results, but since I had spiked to over 25psi the couple times my situation isn't a good marker. I will enjoy tearing my motor down especially since my rods shattered.
CTScottUSA, CT · Apr 30, 2012#8
Originally Posted by pimp my yaris ↑
This is my motor with bent rod and cracked block and piston sleeve. This was at 12psi and 197whp dynoed only 2 days before major engine noise on a mustang dyno. Now on to the build of my junk jard motor. 🤷
Did you post the dyno chart from your mustang run?
johnny_vitzHamilton, Canada · Apr 30, 2012#9
I'm still wondering if there is a difference in the bottom end of the echo/xb compared to the yaris. Blownxa said he went through a few engines just above 150whp in his xa (with a good/safe tune) as well as a couple other xb guys on clubxb.com

Sorry to hear about your engine pimp. How much boost will you be running once it is built?
cali yarisCanoga Park, CA · Apr 30, 2012#10
^ They seem identical to me. I've reviewed them side by side. Don't know about part numbers.
1.5Tampa · Apr 30, 2012#11
thats some high boost for these little guys. Now to the build. Good Luck!
CTScottUSA, CT · Apr 30, 2012#12
Originally Posted by cali yaris ↑
^ They seem identical to me. I've reviewed them side by side. Don't know about part numbers.
Looking at the EPC, the Echo, xA, xB, and Yaris all share the same part numbers for pistons, rods, and crankshaft. The Prius uses the same rods, but different pistons and crankshaft.
fnkngrvIn The Hotbox · Apr 30, 2012#13
The rods are useless unfortunately. I totally underatand why they are what they are, but it still is a fact.
CTScottUSA, CT · Apr 30, 2012#14
Originally Posted by fnkngrv ↑
The rods are useless unfortunately. I totally underatand why they are what they are, but it still is a fact.
It would be very interesting to have one of the stock rods analyzed for its real rating. From what I have been reading in some automotive engineering journals, stock rods are typically designed to handle between 25% and 40% more force than stock, which in our case would mean about 150 HP max (if ours are really 40% over engineered).

If we could find out the compression PSI limit of the stock rods, it would be easy enough to run the math to determine the theoretical boost limit.
eTiMaGoBangkok, Thailand · Apr 30, 2012#15
Crashy would cowering in fear if she could read that post :D
Blown_xaVirginia · Apr 30, 2012#16
I wouldn't tag a certain amount of boost to the limitation of stock rods.... It is power. Most likely the onset of power (torque) is the best measurement of limitation.
CTScottUSA, CT · Apr 30, 2012#17
Originally Posted by Blown_xa ↑
I wouldn't tag a certain amount of boost to the limitation of stock rods.... It is power. Most likely the onset of power (torque) is the best measurement of limitation.
True, although it is the instantaneous force of the combustion explosion pushing against the crank before the rotation occurs that does the damage, as that peak force can be in excess of 6000 lbs. That force is the pressure within the cylinder at combustion multiplied by the area of the piston and by the sine of the angle of the rod at TDC (which is about 10 degrees). So, if that force peaks high enough either the bearing or rod will fail.
YodaFL · Apr 30, 2012#18
Originally Posted by Blown_xa ↑
I wouldn't tag a certain amount of boost to the limitation of stock rods.... It is power. Most likely the onset of power (torque) is the best measurement of limitation.
^^this
pimp my yarisThread starterchicago · Apr 30, 2012#19
Originally Posted by Yoda ↑
Told ya the rods where the first to go lol. Thanks to for getting that Dyno. Be sure to add your info to my durability thread when u get a chance. You pushed it further than i did by 2 psi. At 10psi after awhile I burnt up my valves. How are yours?
Valves and rings were in good condition. I kept it running rich and cool. About 13:1 for cruzing and 11.5:1 for wide open throttle. If it runs to lean U burn valves and rings. My compression was 155 to 160psi on all except the one with the bent rod.
pimp my yarisThread starterchicago · Apr 30, 2012#20
CP 9.5:1 pistons, Pauter rods and a new clutchmasters fx300 clutch ordered today from Micro Image. And now Im broke.
pimp my yarisThread starterchicago · Apr 30, 2012#21
Originally Posted by CTScott ↑
Did you post the dyno chart from your mustang run?
I did not post the Dyno chart from that run. They forgot to print it. My second run after the car warmed up was 193whp. And thats the one they printed. I can assure U it did 197whp. I did 183whp at 10psi and the print out is posted on my other thread on page 25.
fnkngrvIn The Hotbox · Apr 30, 2012#22
Originally Posted by pimp my yaris ↑
And now Im broke.
Broke, but that first time that you drive it with the upgraded internals you know that you will have a shit eating grin on your face 👍
cali yarisCanoga Park, CA · Apr 30, 2012#23
ooh you went 9.5:1 -- NICE...

sorry about the broke part... 🙂
cali yarisCanoga Park, CA · Apr 30, 2012#24
I don't think CTScott was doubting you, I think he wanted to see the chart.
SchizopreniaSurabaya, Indonesia · May 1, 2012#25
Originally Posted by pimp my yaris ↑
CP 9.5:1 pistons, Pauter rods and a new clutchmasters fx300 clutch ordered today from Micro Image. And now Im broke.
wow your build progress just never ends does it,
i myself just pulled a stock zage kit and going just low boost but now you upgraded internals. your internal upgrading thread would be a very very educative as your kit installation build had been.

2 thumbs up for you...
Focus_Sh1ftNew Jersey · May 1, 2012#26
I've always wondered this and could probably use to read about a bit but... How is the engine going to perform with lower compression on stock management?
thefallsSunny place · May 1, 2012#27
Well lower compression will make a lazy engine off boost. I drive a very low compression engine 4efte with 7.8:1 compression[stock management and not tuned yet, at 0.5bar td05].A bit lazy offboost but when on boost it does fly :).

I would assume that 9.5:1 would be much better a drive.
pimp my yarisThread starterchicago · May 1, 2012#28
I was going to stick with stock compression ratio on the advise from my friend who is helping me with the engine bulid. He has a 1000hp supra that runs on E85 alcohol. He is building a 2jz supra motor with stock compression and ridiculous boost levels "30psi+". Because E85 has less problems with detonation. He was trying to get me to run E85 in my car.

I decided to go lower compression and stick with gas as my engine wont be sleeved for crazy horsepower and I drive long distances where E85 may not be available.
cali yarisCanoga Park, CA · May 1, 2012#29
^ Plus the work of changing out fuel lines and such, it's a pain. I opted not to go that way also. The compression you've chosen isn't a lot lower, it won't be very noticeable off boost, and you'll be able to run more boost. It will make tuning easier.
pimp my yarisThread starterchicago · May 1, 2012#30
Life at the center of the Yariverse

1 attachment not included in this copy

pimp my yarisThread starterchicago · May 1, 2012#31
Oil change. THE HARD WAY.

1 attachment not included in this copy

pimp my yarisThread starterchicago · May 1, 2012#32
Old motor boxed up. Head good, Bearing journals and crank good. I will save her for a rainy day and then mabe send her out to get sleeved at Golden Eagle. They can remove the part of cyl. 3 that cracked off and make her stronger then ever.

Oh, if I only had more money. Someday 🤤

1 attachment not included in this copy

Blown_xaVirginia · May 1, 2012#33
Originally Posted by CTScott ↑
True, although it is the instantaneous force of the combustion explosion pushing against the crank before the rotation occurs that does the damage, as that peak force can be in excess of 6000 lbs. That force is the pressure within the cylinder at combustion multiplied by the area of the piston and by the sine of the angle of the rod at TDC (which is about 10 degrees). So, if that force peaks high enough either the bearing or rod will fail.
yea, detonation will kill rods at any power... I meant considering a bad tune not being the culprit .
Blown_xaVirginia · May 1, 2012#34
Originally Posted by pimp my yaris ↑
Old motor boxed up. Head good, Bearing journals and crank good. I will save her for a rainy day and then mabe send her out to get sleeved at Golden Eagle. They can remove the part of cyl. 3 that cracked off and make her stronger then ever.

Oh, if I only had more money. Someday 🤤
Those storage tubs are great, I use those a lot for motor teardowns!
DentGuyAlgonquin · May 1, 2012#35
We will have it up and running again soon!!!
SchizopreniaSurabaya, Indonesia · May 4, 2012#36
Originally Posted by pimp my yaris ↑
Life at the center of the Yariverse
is that the picture of a used engine you got to replace the original broken one?

how much does it cost for a block like that, over there? 🙂
ROCKLAND TOYOTAROCKLAND COUNTY NY · May 4, 2012#37
Originally Posted by Schizoprenia ↑
is that the picture of a used engine you got to replace the original broken one?

how much does it cost for a block like that, over there? 🙂
i got a 2008 motor out of a sedan for $800 with 38K. it was complete from head to pan.....
cali yarisCanoga Park, CA · May 4, 2012#38
I have a short block I'm selling for $200, and full motors go for $500-$1000, depending on mileage and completeness, etc.
pimp my yarisThread starterchicago · May 4, 2012#39
I bought that 2001 Complete Echo motor with 80K miles for 350$. The only thing they took off were the starter and alternator. Now I have a extra intake, cable throttle body and fuel rail that I will modify with a return line soon.
fnkngrvIn The Hotbox · May 4, 2012#40
Originally Posted by pimp my yaris ↑
I bought that 2001 Complete Echo motor with 80K miles for 350$. The only thing they took off were the starter and alternator. Now I have a extra intake, cable throttle body and fuel rail that I will modify with a return line soon.
I bought my motor with 23k on it for 550 last week from an 09. It came with just about the same minus the TB and intake which I would find useless for me anyway. The only real disappointment with it was that the water pump pulley assembly was warped so it is good that mine is fine. I did get lucky though even to having a drop off point with a fork lift to save on the debarkment from the big rig.
1.5Tampa · May 5, 2012#41
I see there are more 1nz engines on ebay for around 500 too.
Focus_Sh1ftNew Jersey · May 5, 2012#42
It's great to know they're so abundantly available at beyond great prices. I've always wanted to pull a motor (but I'm in no hurry 😛).
pimp my yarisThread starterchicago · May 6, 2012#43
Junk yard motor breakdown. New rods and pistons to arrive on 5-9 👏

1 attachment not included in this copy

pimp my yarisThread starterchicago · May 6, 2012#44
These stampings on the crank are needed by the dealer to get the exact size replacement main journal bearings for a rebuild.

1 attachment not included in this copy

pimp my yarisThread starterchicago · May 6, 2012#45
Same goes for rod bearings.

1 attachment not included in this copy

Focus_Sh1ftNew Jersey · May 6, 2012#46
Loving how well documented this is 👍
cali yarisCanoga Park, CA · May 6, 2012#47
me too.
pimp my yarisThread starterchicago · May 7, 2012#48
One thing I have learned with all this engine work is that every bolt and fastener on this car is very small. These bolts do not hold up well in a northern climate where salt is used to melt snow on roads in the winter. I was a little disapointed in toyota quality in this regard. I had a lot of frozen bolts on the motor and some came out with the aluminum threads on the bolt. Some bolt heads just looked like a ball of rust. My car is a 2009 with 60K miles. Should not be this bad. Dumping this much money is this car I may need a second beater so my ride does not rust away. Chicago sucks.
fnkngrvIn The Hotbox · May 7, 2012#49
Not really sure that you can blame the automotive manufacturers when it comes to the environments that the autos reside in. Different regions offer different chemical and environmental hurdles. Now if I had purchased an LS or ES Lexus then I would tend to become more irritated with them since you are taking 36-76k for the car, but on a 12-15k car they are not going to have the most resilent alloys for parts unfortunately. I am feeling your pain as well right now. That is why I am upgrading to ARP bolts/studs. They may add up to a lot, but worth it in the end.

As for the documentation, this is great to know for sure!
ViperoniBrampton, ON · May 8, 2012#50
Originally Posted by fnkngrv ↑
Not really sure that you can blame the automotive manufacturers when it comes to the environments that the autos reside in. Different regions offer different chemical and environmental hurdles. Now if I had purchased an LS or ES Lexus then I would tend to become more irritated with them since you are taking 36-76k for the car, but on a 12-15k car they are not going to have the most resilent alloys for parts unfortunately. I am feeling your pain as well right now. That is why I am upgrading to ARP bolts/studs. They may add up to a lot, but worth it in the end.
I've had bolts snap that shouldn't, the metal just seems weak.
Case in point, my alternator adjustment bolt (the top bolt), snapped in the case of the alternator. I've never had that happen, and I wasn't even putting a ton of force on it when it happened. Same for the other bolts I've snapped.

If you remove any bolts, definitely grease them before putting them back in LOL


Good pics of the disassembly!