Yarisworld Archive

Limits of stock 1nzfe found once and for all.

167 posts · 63,684 views · page 2 of 4

Replies continued

Focus_Sh1ftNew Jersey · May 8, 2012#51
Originally Posted by pimp my yaris ↑
One thing I have learned with all this engine work is that every bolt and fastener on this car is very small. These bolts do not hold up well in a northern climate where salt is used to melt snow on roads in the winter. I was a little disapointed in toyota quality in this regard. I had a lot of frozen bolts on the motor and some came out with the aluminum threads on the bolt. Some bolt heads just looked like a ball of rust. My car is a 2009 with 60K miles. Should not be this bad. Dumping this much money is this car I may need a second beater so my ride does not rust away. Chicago sucks.
I don't know about Chicago, but I swear since I started driving about 5 years ago that the amount of road salt used has increased drastically...
fnkngrvIn The Hotbox · May 8, 2012#52
Originally Posted by Focus_Sh1ft ↑
I don't know about Chicago, but I swear since I started driving about 5 years ago that the amount of road salt used has increased drastically...

My motor blowing up is a direct result of the chemicals they put down on the roadways in my county. Believe it or not I actually took great pics over to my city office to show them that they need to reconsider their choice in winter roadway safety techniques. Heaven forbid ot causes failure or steering or suspension components causing and accident with the end reault being death or dismemberment. It is also because of that solution thy use that my lower alternator bolt head was fubar along with other bolts I have removed.
pimp my yarisThread starterchicago · May 8, 2012#53
My alternator is still in the engine compartment. It could not be seperated from the positive battery cable. It started to twist the stud even after letting it soak overnight in penatrating oil. I let it be, and its still attached to the harness. I also had problems with alternator and A/C compressor mounting bolts and T-stat studs, bypass tube studs and dip stick hold down. My previous car was a 93 lexus sc300 with 178,000 mi. I never had problems like this. This car seems disposable by comparison.
ROCKLAND TOYOTAROCKLAND COUNTY NY · May 9, 2012#54
Originally Posted by fnkngrv ↑
Not really sure that you can blame the automotive manufacturers when it comes to the environments that the autos reside in. Different regions offer different chemical and environmental hurdles. Now if I had purchased an LS or ES Lexus then I would tend to become more irritated with them since you are taking 36-76k for the car, but on a 12-15k car they are not going to have the most resilent alloys for parts unfortunately. I am feeling your pain as well right now. That is why I am upgrading to ARP bolts/studs. They may add up to a lot, but worth it in the end.

As for the documentation, this is great to know for sure!
SO your saying that lexus(TOYOTA) uses better grade materials on its vehicles??? you do know its all the same stuff right....
GolddeenohColumbia, SC · May 9, 2012#55
Lexus = expensive Toyota. basically anything fancier than an Avalon is a Lexus.
pimp my yarisThread starterchicago · May 12, 2012#56
Its time to get serious. Unfortunatly I am still waiting on one crank main bearing that is coming on a slow boat from Japan. These rods look incredibly strong. 😁

1 attachment not included in this copy

cali yarisCanoga Park, CA · May 12, 2012#57
^ I haven't been able to break one yet. 😁
Focus_Sh1ftNew Jersey · May 12, 2012#58
Those are easily twice the size of the normal rods 🤤
changchewsoonMalaysia · May 12, 2012#59
Pauter rods are definitely one of the best! I was trying to lay my hands on them when I first started my build but then somehow settled for Crower.
fnkngrvIn The Hotbox · May 12, 2012#60
Originally Posted by ROCKLAND TOYOTA ↑
SO your saying that lexus(TOYOTA) uses better grade materials on its vehicles??? you do know its all the same stuff right....
So in other words you are saying that the Lexus that comes stock handling over 2 times the horsepower is merely handling that because it has "bigger" parts due to larger displacement? If that is the case then I digress however I would be surprised and saddened.
AltitudeColorado · May 12, 2012#61
Originally Posted by pimp my yaris ↑
Its time to get serious. Unfortunatly I am still waiting on one crank main bearing that is coming on a slow boat from Japan. These rods look incredibly strong. 😁
I LOVE shiny auto parts.
pimp my yarisThread starterchicago · May 15, 2012#62
It looks like I should get my parts in by the end of the week. Time to start check list. Cylinder hone, check assembly lube, check, plsti-guage check. I am already looking at new turbo's and planing a 3" downpipe from hell. Not yet sure I can make it fit yet.
why?harnett county NC · May 15, 2012#63
Originally Posted by fnkngrv ↑
So in other words you are saying that the Lexus that comes stock handling over 2 times the horsepower is merely handling that because it has "bigger" parts due to larger displacement? If that is the case then I digress however I would be surprised and saddened.
the engineering and the math is different. But I'd be shocked if the alloys are different. Most of Toyota's v8's are even all aluminum now. Only the IS F and the LFA mention anything other than aluminum.

There is a reason people can push 30 or 40 more horsepower through the car easily, and only really experience problems at over double the stock horsepower.

There is also a reason the 2JZ can push out all sorts of insane power levels.
Blown_xaVirginia · May 15, 2012#64
Originally Posted by pimp my yaris ↑
It looks like I should get my parts in by the end of the week. Time to start check list. Cylinder hone, check assembly lube, check, plsti-guage check. I am already looking at new turbo's and planing a 3" downpipe from hell. Not yet sure I can make it fit yet.
Do it, 3" dp will fit, depends on turbo outlet location. Motor mount inserts help ease clearance worries.
TURBO YARISUSA · May 15, 2012#65
What did you mean by this " Most of Toyota's v8's are even all aluminum now. Only the IS F and the LFA mention anything other than aluminum."?
pimp my yarisThread starterchicago · May 15, 2012#66
Originally Posted by Blown_xa ↑
Do it, 3" dp will fit, depends on turbo outlet location. Motor mount inserts help ease clearance worries.
What are these motor mount inserts you speak of? I could use something to stop the twisting. Im sure it will only get worse now on.
Blown_xaVirginia · May 17, 2012#67
Originally Posted by pimp my yaris ↑
What are these motor mount inserts you speak of? I could use something to stop the twisting. Im sure it will only get worse now on.
Check with energy suspension to see if they make them for the Yaris. That is what I use.
DentGuyAlgonquin · May 19, 2012#68
3/4 of the shortblock is back together.
pimp my yarisThread starterchicago · May 20, 2012#69
Progress and set backs this weekend. I finally recieved all my engine bearings from Toyota on thursday. This weekend I set out to build this short block with a friend "Dent Guy" who built his own 1000hp 2jz supra motor. The instructions for the rods say U may need notch the block for the rod clearance on small bore engines. It took three attemps to remove enough material to clear the rods during crank rotation and still have the indicated 1/16 clearance remaining. And this also means cleaning the block and oil passages three times and R&R the crank three times. This took a long time. On final assembly the very last piston compression ring on the last piston broke while my friend was very gently sliding it over the top of the piston. THAT SuCKED. I was hoping to get this thing running by today or tomarrow. So now I will be ordering a ring set for one piston from CP on monday and hopfully having it shipped overnight to finish assembly on the short block.👎

2 attachments not included in this copy

pimp my yarisThread starterchicago · May 20, 2012#70
more pics

2 attachments not included in this copy

pimp my yarisThread starterchicago · May 20, 2012#71
more

1 attachment not included in this copy

pimp my yarisThread starterchicago · May 20, 2012#72
This was my first attempt at notching the block. It was not nearly enough as seen by the assembled pic.

1 attachment not included in this copy

Focus_Sh1ftNew Jersey · May 21, 2012#73
Great pics - can't wait to see it come together!
ilikericesavannah, ga · May 21, 2012#74
wow.. this looks like so much fun.. I need to get me a short block and build it up just for fun.. awesome pics

also thinking a 1nz would make a great water sprinkler, don't you think?
DentGuyAlgonquin · May 21, 2012#75
Talk about frustrating! Im still pissed at myself for that ring 🙄
CTScottUSA, CT · May 21, 2012#76
That's a little scary with the ring snapping that easily. Are those OEM rings, or did they come with the new pistons?
DentGuyAlgonquin · May 21, 2012#77
Originally Posted by CTScott ↑
That's a little scary with the ring snapping that easily. Are those OEM rings, or did they come with the new pistons?
They were the rings that came with the CP pistons. They are delicate
cali yarisCanoga Park, CA · May 21, 2012#78
I knew about the notching, sorry I didn't post anything about that beforehand. I think you have a ring on the way, those are cast iron, so yeah they take a soft touch.
Blown_xaVirginia · May 21, 2012#79
The 2nd ring is like that, it is a cast material (not just on our motors, and not just CP). What ring gaps did you decide?
pimp my yarisThread starterchicago · May 22, 2012#80
Originally Posted by Blown_xa ↑
The 2nd ring is like that, it is a cast material (not just on our motors, and not just CP). What ring gaps did you decide?
Not sure exactly what the ring gap was. I had a friend helping with the rebuild he brought a ring grinder but he said the sizing was perfect. I think they were all just a few thousandths larger then the minimum recomended gap.

These are some pics of my progression today after getting my second compression ring overnighted from CP. I am hoping tomarrow to bolt on clutch, flywheel and trans. Also get her hung in the engine compartment.😁

I miss my car 😢
pimp my yarisThread starterchicago · May 22, 2012#81
pics

2 attachments not included in this copy

pimp my yarisThread starterchicago · May 22, 2012#82
more pics

2 attachments not included in this copy

pimp my yarisThread starterchicago · May 22, 2012#83
one more

1 attachment not included in this copy

cali yarisCanoga Park, CA · May 22, 2012#84
That's coming along great. I think I'd be too tempted by "as long as I'm in here" mods.... good on you!
pimp my yarisThread starterchicago · May 23, 2012#85
Just a little tip for do it yourselfers. When tightening head bolts lay the engine on its side or it will spin like a top.
GolddeenohColumbia, SC · May 23, 2012#86
or have it in a mount so that it doesn't move either. :P I Envy your garage.
DentGuyAlgonquin · May 23, 2012#87
Surprisingly enough the ring gaps were perfect right out of the box. Ive never had that happen before with file fit rings. They were all .017"-.018" on the first compression ring and .025"-.026" on the second.

Nice work getting the thing slapped back together so quickly!!!
Blown_xaVirginia · May 23, 2012#88
Originally Posted by DentGuy ↑
Surprisingly enough the ring gaps were perfect right out of the box. Ive never had that happen before with file fit rings. They were all .017"-.018" on the first compression ring and .025"-.026" on the second.

Nice work getting the thing slapped back together so quickly!!!
I've run into that, it is rare though. Ring grinding is time consuming !
fnkngrvIn The Hotbox · May 24, 2012#89
Originally Posted by cali yaris ↑
I think I'd be too tempted by "as long as I'm in here" mods.... good on you!

Been there...doing that now! 😆

Brian, are you planning on pushing the new motor to see where you can go with it without being sleeved?
djgab101australia · May 24, 2012#90
Haven't posted of here in ages! Today driving in the morning my car make a crack sound and something in the engine is making a ticking noise when I drive drove it home and left it there! Once I get home I can check and see if i can find the problem! It was freezing this morning I let the car warm up coolant temp was roughly 70*c and intake tempt was 17*c I hope my internals aren't damaged
DentGuyAlgonquin · May 24, 2012#91
Do a compression check to see if you may have bent a rod.
djgab101australia · May 25, 2012#92
Hopefully some time soon I can start dismantling and see wat I find!
pimp my yarisThread starterchicago · May 25, 2012#93
made more progress yesterday, but I ran out of daylight before I could get her wired up.

2 attachments not included in this copy

pimp my yarisThread starterchicago · May 25, 2012#94
Originally Posted by djgab101 ↑
Hopefully some time soon I can start dismantling and see wat I find!
Yes if your running a turbo the rods are the weak spot. My rod bent on a cooler day when my car was making great power.
YodaFL · May 25, 2012#95
It's looking good. What turbo do u have you eyes on?
pimp my yarisThread starterchicago · May 25, 2012#96
Originally Posted by Yoda ↑
It's looking good. What turbo do u have you eyes on?
For now Im going to stay with the same turbo. I am going to by some larger injectors and add a return line. Then I am going to buy the Ptuning turbo manafold that locates the turbo above the valve cover and a T3 style turbo with a external wastegate and a dump tube. I will also make a three inch exhaust.
cali yarisCanoga Park, CA · May 25, 2012#97
beast!
GolddeenohColumbia, SC · May 25, 2012#98
Originally Posted by pimp my yaris ↑
For now Im going to stay with the same turbo. I am going to by some larger injectors and add a return line. Then I am going to buy the Ptuning turbo manafold that locates the turbo above the valve cover and a T3 style turbo with a external wastegate and a dump tube. I will also make a three inch exhaust.
once you get all the specs worked out send them to Garm so we can persuade him into setting up and creating a kit 😉
pimp my yarisThread starterchicago · May 26, 2012#99
something like this

1 attachment not included in this copy

GolddeenohColumbia, SC · May 26, 2012#100
what are you going to do about the cowl on the car to allow the turbo to fit with out melting the plastic?