Yarisworld Archive

Limits of stock 1nzfe found once and for all.

167 posts · 63,684 views · page 3 of 4

Replies continued

cali yarisCanoga Park, CA · May 26, 2012#101
^ Dremel. 😁
YodaFL · May 26, 2012#102
Wat about rain?
GolddeenohColumbia, SC · May 26, 2012#103
if it isn't a daily driver and is kept inside a garage it could just be removed and allow better ventilation of the engine bay add an under panel kit and then air would theoretically go in through the grill over the intake, and over the intake side turbo piping and then exit over the windshield. but leaving that opening will allow a lot of stuff to possibly fall into the engine bay and not having windshield wipers in the rain might be a problem but otherwise it could be an increased functionality of the system :D
ilikericesavannah, ga · May 26, 2012#104
I like this setup alot
cali yarisCanoga Park, CA · May 27, 2012#105
Is this how blown_xA's turbo is set up?
pimp my yarisThread starterchicago · May 27, 2012#106
Originally Posted by cali yaris ↑
Is this how blown_xA's turbo is set up?
Yes this is the same set up as blown XA
pimp my yarisThread starterchicago · May 27, 2012#107
I am not able to start my car after reassembly. I am getting spark and fuel but I think the timing may be off I have tried swaping cam and crank sensors already. I have also double checked timing chain. I can see rpm on my scanner when cranking engine. Compression dry is 85-90 psi and 120 with a little oil. I know the rings have not seated yet. I am wondering if the crankshaft tone ring on a older 1nz may be differn't from my newer engine I took out. The part number for the sensor is the same.

If anyone has had similar problem after engine swap let me know? I bought a timing light and will try to check soon while cranking. It will sputter a little but will not start.

Any ideas welcome?
CTScottUSA, CT · May 27, 2012#108
Originally Posted by pimp my yaris ↑
I am not able to start my car after reassembly. I am getting spark and fuel but I think the timing may be off I have tried swaping cam and crank sensors already. I have also double checked timing chain. I can see rpm on my scanner when cranking engine. Compression dry is 85-90 psi and 120 with a little oil. I know the rings have not seated yet. I am wondering if the crankshaft tone ring on a older 1nz may be differn't from my newer engine I took out. The part number for the sensor is the same.

If anyone has had similar problem after engine swap let me know? I bought a timing light and will try to check soon while cranking. It will sputter a little but will not start.

Any ideas welcome?
Is the harness hooked back up completely, including the ground terminals that bolt to the block as some of those are the only ground for some of the sensors?
pimp my yarisThread starterchicago · May 27, 2012#109
I connected two grounds to the cylinder head and the neg. batt cable to the trans. I will double check them tomarrow and clean them. Thanks for good idea.
fnkngrvIn The Hotbox · May 27, 2012#110
Originally Posted by CTScott ↑
Is the harness hooked back up completely, including the ground terminals that bolt to the block as some of those are the only ground for some of the sensors?

Those two grounds on the driver's side create quite the symptoms if not attached properly...I can attest to that!
ilikericesavannah, ga · May 28, 2012#111
Originally Posted by pimp my yaris ↑
I am not able to start my car after reassembly. I am getting spark and fuel but I think the timing may be off I have tried swaping cam and crank sensors already. I have also double checked timing chain. I can see rpm on my scanner when cranking engine. Compression dry is 85-90 psi and 120 with a little oil. I know the rings have not seated yet. I am wondering if the crankshaft tone ring on a older 1nz may be differn't from my newer engine I took out. The part number for the sensor is the same.

If anyone has had similar problem after engine swap let me know? I bought a timing light and will try to check soon while cranking. It will sputter a little but will not start.

Any ideas welcome?
I had a problem very similar to yours when I did the desludge in a 2003 camry 4 cyl. I actually had the exhaust cam 90degrees off. Because of the timing marks are all 4 points of the cam gear and only one of those marks has a very small extra mark below it that was covered up just a little bit that I missed with the wire brush.

Double/triple check your marks on your cam gears and make sure you have the correct marks and all your lobes are pointing in the correct position in TDC.

There was no damage to the 2az motor because of this. Just something to check also. You never know. good luck
pimp my yarisThread starterchicago · May 28, 2012#112
I will check the cam timing again. The grounds are all good. I even attached a jumper cable from neg. battery to engine block. No luck yet. I feel im getting closer though. Thanks for tips everyone.
pimp my yarisThread starterchicago · May 28, 2012#113
Holly shit U were right. Thanks so much "I like rice" U have no idea how much I have been stressing over this rebuild that wont start. I will correct this and see if she fires up. 👍
ilikericesavannah, ga · May 28, 2012#114
Originally Posted by pimp my yaris ↑
Holly shit U were right. Thanks so much "I like rice" U have no idea how much I have been stressing over this rebuild that wont start. I will correct this and see if she fires up. 👍
🙇

your welcome pimp! So glad this worked for you and I am not the only one who has made that mistake.. hahaha.. I felt like an ass when I did it.
pimp my yarisThread starterchicago · May 29, 2012#115
Well I got it started after correcting exhaust cam timing that was off 90 degrees. Took it for a drive after burping coolant bubbles. It sounded like I have marbles in my engine at idle and I had a knocking noise under load. I did this test drive without the turbo and mass air and air filter attached directly to the T-body. I thought for sure I had some major piston slap going on under load causing the knocking.

I just about threw in the towl on this motor. I was still fucking around at 9:30 last night and decided to hook up the turbo just for kicks. Mabe take it out with a bang! I was blown away when the knocking noise went away. I am certain now it was internal engine noise coming through the air filter.

I still have the marbles noise at idle but I believe it may be a valve clearance problem. I hope. I will check it out and let you all know. This has been a very stressfull weekend.
thefallsSunny place · May 29, 2012#116
This is a very nice thread. Hope your car is running well.
Are you planning to run beyond the normal rev limit? Any plans to change to the yaris cup valve springs,since you may have to check the valve clearance anyways?

Also what break in procedure are you following?
Blown_xaVirginia · May 29, 2012#117
Originally Posted by pimp my yaris ↑
Well I got it started after correcting exhaust cam timing that was off 90 degrees. Took it for a drive after burping coolant bubbles. It sounded like I have marbles in my engine at idle and I had a knocking noise under load. I did this test drive without the turbo and mass air and air filter attached directly to the T-body. I thought for sure I had some major piston slap going on under load causing the knocking.

I just about threw in the towl on this motor. I was still fucking around at 9:30 last night and decided to hook up the turbo just for kicks. Mabe take it out with a bang! I was blown away when the knocking noise went away. I am certain now it was internal engine noise coming through the air filter.

I still have the marbles noise at idle but I believe it may be a valve clearance problem. I hope. I will check it out and let you all know. This has been a very stressfull weekend.
The valve spring buckets vary in thickness , were they put back in the original positions? That may be the noise. Most built motors do make some noise because of the extra piston to wall clearance forged pistons call for.
pimp my yarisThread starterchicago · May 29, 2012#118
Originally Posted by thefalls ↑
This is a very nice thread. Hope your car is running well.
Are you planning to run beyond the normal rev limit? Any plans to change to the yaris cup valve springs,since you may have to check the valve clearance anyways?

Also what break in procedure are you following?
No plans to change rev limit at this time. I have no more money at this time to change valve springs. If I get the engine sorted out, I will change turbo and exhaust manafold and turbo back exhaust system.

I am taking it easy on the engine "below 4K rpm" for about 750-1000 miles
pimp my yarisThread starterchicago · May 30, 2012#119
Originally Posted by Blown_xa ↑
The valve spring buckets vary in thickness , were they put back in the original positions? That may be the noise. Most built motors do make some noise because of the extra piston to wall clearance forged pistons call for.
Yes, I am wondering about valve spring bucket placement. I will check this out in the next day or two. I needed a day to break and destress. Just out of curiosity does your engine have some piston rattle at idle? I know its sleeved but I am sure U are still running forged pistons.
Blown_xaVirginia · May 30, 2012#120
Originally Posted by pimp my yaris ↑
Yes, I am wondering about valve spring bucket placement. I will check this out in the next day or two. I needed a day to break and destress. Just out of curiosity does your engine have some piston rattle at idle? I know its sleeved but I am sure U are still running forged pistons.
It isn't sleeved actually, and yes... it sounds like a vw tdi.
DentGuyAlgonquin · May 30, 2012#121
Don't go easy on the engine Brian. Higher cylinder pressures will push the rings out against against the cylinder wall which will make them seat better.
cali yarisCanoga Park, CA · May 30, 2012#122
Mine is sleeved and I have some noise.

Our break-in included 5 or 10 minutes at 2000 rpm, change the oil, I think two rounds of that at different rpm's, before driving.
pimp my yarisThread starterchicago · May 30, 2012#123
Ok, I checked all valves and they are all within toyota spec. And VW TDI is the pefect way to describe the noise at idle. A older VW from the 90's, not one of those new ones that are so quite.

They should tell you this in the instructions for the pistons so you don't loose your mind when you start it.

Took it for a drive again and got on her a little. No problems so far. I can feel I lost a little torque with the lower compression pistons. I will make it up later once some fuel upgrades are done and I can crank up the boost a little.🤣

I am so happy to have a car again. And the clutchmasters clutch is much more streetable then my 6 puck ceramic clutch I was using. Although pedal pressure is much higher with this new clutch.
why?harnett county NC · May 31, 2012#125
Originally Posted by Blown_xa ↑
http://www.scionlife.com/forums/showthread.php?t=215013 some more photos of a clean setup I just did on a friends xB (for future ideas). Made 156whp at 4psi on our dyno, pretty darn awesome ( about 171 dynojet). It still has factory cat!

That sounds pretty amazing. Is there a lot of turbo lag? What other mods are on it? 4psi for 156 just sounds high for what we see here, is the xB plumbing bigger stock?
pimp my yarisThread starterchicago · May 31, 2012#126
Did some retuning today. Engine is running great. It is running a little rich with the lower compression pistons.
DentGuyAlgonquin · May 31, 2012#127
Let's invent you a fuel system now
Blown_xaVirginia · Jun 1, 2012#128
Originally Posted by why? ↑
That sounds pretty amazing. Is there a lot of turbo lag? What other mods are on it? 4psi for 156 just sounds high for what we see here, is the xB plumbing bigger stock?
Magnaflow cat back exhaust was the only mod in conjunction with the kit. Lag is not noticed at all, powerband is convex. The manifold was the key component to achieve good results. That turbo on my car has some lag, but I have low compression. Car was tuned off wastgate spring pressure (3psi) but it was 4psi due to perhaps the new spring . t3 60trim turbo is great for the 1nzfe.
YodaFL · Jun 4, 2012#129
are you going to be upgrading your motor mounts also?
pimp my yarisThread starterchicago · Jun 4, 2012#130
Mabe in time. Haven't had any problems with them so far. I need to make a return line for my stock fuel rail first. Also add a external regulator that will increase fuel pressure with boost. My Tc injectors are maxed at 12psi and stock fuel pressure.
fnkngrvIn The Hotbox · Jun 4, 2012#131
Originally Posted by pimp my yaris ↑
Mabe in time. Haven't had any problems with them so far. I need to make a return line for my stock fuel rail first. Also add a external regulator that will increase fuel pressure with boost. My Tc injectors are maxed at 12psi and stock fuel pressure.
CTScott and I were talking about this earlier this evening in reference to my car as well. I have my replacement motor in and running, but I need to replace the oil pan sub assembly this weekend before I consider it really "back on the road". I do however have my Autometer Fuel Pressure Gauge installed and today doing a test drive of about 10 miles the FP is staying at roughly 48psi regardless of being at 0, 5, or 9psi of boost. We need to be at a 1:1 so technically at 9psi of boost then the FP should be at roughly 53psi as per our hunches. You said that you are already running a 255lph pump right and that you don't think that it is a true Walboro? IMHO if you are going to be getting into the tank anyway to upgrade your system then I would change to a Walboro 190lhp since you aren't going to be hitting over 300-320hp so that you aren't returning a heap ton of heated fuel. If all goes well and I have the car back on the road by the beginning of next week then I will go ahead and try to make a video showing my FP at the different levels of boost up to 6-8psi so that people can see.
cali yarisCanoga Park, CA · Jun 5, 2012#132
^ I run my car all day long at 14psi (~270 whp) on a Walbro 255, never had any issues at all, including track days.

Do you really think the fuel is still hot after it passed right by the injectors and was returned to the tank? When does it have time to get hot?

And that's a long return run to cool off on the way back even if it DID get hot. This detail is a non-issue IMO.
fnkngrvIn The Hotbox · Jun 5, 2012#133
^ I am going off of the guidance of the engineer that I spoke with at length about which pump to install in my car as long as I planned on staying under 400hp. He was one of the designers of the fuel pump itself for the 190/255. Who knows, perhaps he is mistaken, but then again maybe he isn't and according to him Walboro has done extensive studies in regards to what serviceability is provided at each level or their products. Some folks chose to completely over engineer what they have and others chose to balance things out. I have seen plenty of cases where over engineering in the long run caused more harm then good. Your case very well could be one of those exceptions. I hope that it is for you, but for me I will always perform due diligence and do what is best for me. If I happen upon information from what I consider a solid source then I will always pass it along and leave those that I give it the chance to use it for their projects or not. It is of course ultimately their own choice.
cali yarisCanoga Park, CA · Jun 5, 2012#134
Agreed on all counts. I'll take my real world experience (3 builds so far all with the same results with respect to fuel pumps) over that engineer, and agree to disagree.

Explain again (I can't find it in this thread) why a stronger pump isn't a good idea, when you can regulate the pressure to whatever you want.

I used an Aeromotive A1000 in my tC, that is good up to I think over 1000 hp, and I was pushing 440 whp. Just a further example....
pimp my yarisThread starterchicago · Jun 5, 2012#135
I know that warming fuel in the tank has a negative affect on fuel mileage. This is the whole reason of new cars going with the returnless system.
Most Tuners go overkill as a method of extra piece of mind and give room for futher performance gains later.

I will be replacing my pump because the shrader valve at the outlet of the pump that maintains fuel pressure when the car turns off is intermittantly not working giving me a long crank time. I think I may stay with the 255lph as I will be trying for that 300whp goal. Blown XA is pulling it off without a sleeved motor and has been reliable so far. I will try the same.
pimp my yarisThread starterchicago · Jun 6, 2012#136
I see a lot of tuning shops are charging big money for balancing motors. I spoke with some people about this while doing my rebuild. Then I called a very reputable shop locally that builds some monster motors 1000hp +. and I asked him if they could balance my rotating assembly. He first asked what motor it is. I explaned it was a inline four cyl. He told me balancing is not nearly as important on a inline motor as a V motor. I told him the brands of parts I am using for pistons and rods. He said that Pauter and CP are excellent brands that will balance there parts before shipping them out. He said its really not needed and didn't want to waste my money. My friend "dent guy" who helped me with my engine build is runing a inline 2jz with over 900whp and off the shelf rods and pistons is not having any problems. Just thought this is good info for those thinking of a rebuild.
TURBO YARISUSA · Jun 6, 2012#137
Was the shop you spoke to a machine shop? Or a performance shop?

There are numerous advantages to balancing a motor. Balancing goes hand-in-hand with performance engine building. Balancing reduces internal loads and vibrations that stress metal and may eventually lead to component failure. But is it worth the time and effort for mild performance applications, everyday passenger car engines or low-buck rebuilds?

From a technical point of view, every engine regardless of the application or its selling price can benefit from balancing. A smoother-running engine is also a more powerful engine. Less energy is wasted by the crank as it thrashes about in its bearings, which translates into a little more usable power at the flywheel. Reducing engine vibration also reduces stress on motor mounts and external accessories.

Though all engines are balanced from the factory (some to a better degree than others), the original balance is lost when the pistons, connecting rods or crankshaft are replaced or interchanged with those from other engines. The factory balance job is based on the reciprocating weight of the OE pistons and rods. If any replacements or substitutions are made, there’s no guarantee the new parts will match the weights of the original parts closely enough to retain the original balance. Most aftermarket replacement parts are "balanced" to the average weight of the OEM parts, which may or may not be close enough to maintain a reasonable degree of balance inside the engine.
cali yarisCanoga Park, CA · Jun 6, 2012#138
I didn't balance my lower end -- doin' just fine over here.

Unless you go the "blank check" route, you have to make choices on which motor work to do that will get you "just a little bit more".
I chose to do what would make the most power for the money I could spend on my build.

Hasn't been a reliability issue - at all.
DentGuyAlgonquin · Jun 6, 2012#139
When you start doing things like "knife edging" the crank or offset grinding the journals then it can really mess with the balance or a rotating assembly. The machine shop all of us local guys use (including Sound Performance and AMS) has never seen a 2J crank out of balance. During my first engine build I went over kill with the machine shop and had them do a dynamic balance of the entire rotating assy. (Wiseco pistons, Carillo rods, ATI damper, RPS carbon clutch) Guess what... it need no adjustments.
Now im no Yaris expert but it seems to me that a clean and centered install of the Main caps will free up more power than having that .0001 grams balanced out of the crank. Certain motors will benifit from the additional balancing (V formats mainly) but Inline engines dont inflict the type of counteracting forces on the crank that the V styles engines do.
pimp my yarisThread starterchicago · Jun 6, 2012#140
Originally Posted by TURBO YARIS ↑
Was the shop you spoke to a machine shop? Or a performance shop?

There are numerous advantages to balancing a motor. Balancing goes hand-in-hand with performance engine building. Balancing reduces internal loads and vibrations that stress metal and may eventually lead to component failure. But is it worth the time and effort for mild performance applications, everyday passenger car engines or low-buck rebuilds?

From a technical point of view, every engine regardless of the application or its selling price can benefit from balancing. A smoother-running engine is also a more powerful engine. Less energy is wasted by the crank as it thrashes about in its bearings, which translates into a little more usable power at the flywheel. Reducing engine vibration also reduces stress on motor mounts and

Though all engines are balanced from the factory (some to a better degree than others), the original balance is lost when the pistons, connecting rods or crankshaft are replaced or interchanged with those from other engines. The factory balance job is based on the reciprocating weight of the OE pistons and rods. If any replacements or substitutions are made, there’s no guarantee the new parts will match the weights of the original parts closely enough to retain the original balance. Most aftermarket replacement parts are "balanced" to the average weight of the OEM parts, which may or may not be close enough to maintain a reasonable degree of balance inside the engine.
This was a very reputable machine shop in the Chicago burbs. He told me that quality after market rods and pistons will be balanced to within a tenth of a gram. I assembled my engine and it runs perfect. No vibration.
TURBO YARISUSA · Jun 7, 2012#141
Originally Posted by cali yaris ↑
I didn't balance my lower end -- doin' just fine over here.

Unless you go the "blank check" route, you have to make choices on which motor work to do that will get you "just a little bit more".
I chose to do what would make the most power for the money I could spend on my build.

Hasn't been a reliability issue - at all.
How much does it cost to balance a motor in CA? Its only $200-$250 here.
TURBO YARISUSA · Jun 7, 2012#142
Originally Posted by pimp my yaris ↑
This was a very reputable machine shop in the Chicago burbs. He told me that quality after market rods and pistons will be balanced to within a tenth of a gram. I assembled my engine and it runs perfect. No vibration.
Balancing is done on the crank also. If you replace the lighter factory rods and pistons with the heavier aftermaket rods & pistons the balance has to be off. I not saying that your motor will break just cause you didnt balance it. I just saying it is an advantage in reliability & HP if you do.

And the reliability will be long term not short term.
cali yarisCanoga Park, CA · Jun 7, 2012#143
^ How long?

Almost two years beating on it so far. Seems pretty reliable to me. I wonder if blown_xA balanced his. He's been beating on that thing for a while as well.

I'm not saying no one should do it; I'm saying my experience is that it hasn't been needed on my build projects.
why?harnett county NC · Jun 8, 2012#144
balancing a four cylinder engine is just a waste. Your info really is only good for massive engines or older ones.

Modern engines come off the line almost perfectly specced, and aftermarket companies can now have all the same equipment and ability that the manufacturers have.

This isn't the 60's anymore. There are a lot of things people did as a a matter of course on those cars that is totally useless on ours.
TURBO YARISUSA · Jun 8, 2012#145
Originally Posted by why? ↑
balancing a four cylinder engine is just a waste. Your info really is only good for massive engines or older ones.

Modern engines come off the line almost perfectly specced, and aftermarket companies can now have all the same equipment and ability that the manufacturers have.

This isn't the 60's anymore. There are a lot of things people did as a a matter of course on those cars that is totally useless on ours.
Any and every engine not mater how many cylinders, configuration or size will benefit from having its rotating assembly balance. If the factory piston and rod weight 100 grams together & you replace it with an aftermarket piston & rod which is either lighter (75 grams) or heavier (125 grams) the factory balance is gone. And yes it isnt the 60's, so why wouldnt you do a process to engine that is done by every professional engine builder and has proven result time & time again? BTW my weight #'s are just examples. Im well aware that the factory pistons & rods are lighter than a set of CP's & Pauter.
TURBO YARISUSA · Jun 8, 2012#146
Originally Posted by why? ↑
balancing a four cylinder engine is just a waste. Your info really is only good for massive engines or older ones.

Modern engines come off the line almost perfectly specced, and aftermarket companies can now have all the same equipment and ability that the manufacturers have.

This isn't the 60's anymore. There are a lot of things people did as a a matter of course on those cars that is totally useless on ours.
In my shop right now. I build engines everyday. Im not a flake internet tough guy. I know what Im saying is a fact. If you guys keep on thinking like this you will never evolve........

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

7 attachments not included in this copy

TURBO YARISUSA · Jun 8, 2012#147
Originally Posted by why? ↑
balancing a four cylinder engine is just a waste. Your info really is only good for massive engines or older ones.

Modern engines come off the line almost perfectly specced, and aftermarket companies can now have all the same equipment and ability that the manufacturers have.

This isn't the 60's anymore. There are a lot of things people did as a a matter of course on those cars that is totally useless on ours.
I wonder what Colin Chapman would respond to you if he read the above statement.......
Blown_xaVirginia · Jun 8, 2012#148
Yea mine is balanced. The 1nzfe shortblock we offer comes balanced... I can't compare a non balanced motor because every one we assemble is. The machine shop who handles our motors includes balancing the rotation assembly in the process. Rods come back numbered for specific assembly order. My built motor has over 40k on it now ( not easy miles , trust me).... is it because it is balanced ? I couldnt say
TURBO YARISUSA · Jun 8, 2012#149
Blown: Im not surprised @ all that your motors is balanced. There is absolutely no logical reason not to. The next thing you know someone is going to say that blueprinting is a waste on 4 cylinder........
cali yarisCanoga Park, CA · Jun 8, 2012#150
I never said don't do it, or that's it's a bad idea, or that it won't make power.

Now I'm going to have to ask and find out if, after all that, they balanced mine too. I didn't think so.