This makes me wonder if the Rostra CC install is the same for the 2012/13 as it is in the second gen. I yanked it all out of my 08 to put in the new one, just haven't gotten around to finding install guides for it, lol
DIY Cruise Control for 2012 Yaris - Good News!
279 posts · 466,057 views · page 2 of 6
Replies continued
Did you have the Rostra with the little stalk on the left side of the wheel, or the Rostra kit which used the OEM right side stalk?Originally Posted by mr_miles ↑This makes me wonder if the Rostra CC install is the same for the 2012/13 as it is in the second gen. I yanked it all out of my 08 to put in the new one, just haven't gotten around to finding install guides for it, lol
i have the kit with the stalk on the left side.
Ah. That will probably still work, but really isn't worth the effort. With the 2012, you can simply install the OEM stalk and be good to go (without all of the crazy wiring required for the Rostra kit). If you are interested, I would trade you one of the OEM stalk kits for your Rostra kit, so I can experiment with it to see if it would really work for 2nd gen European owners (I have suspected for quite some time that it will, but have not had the opportunity to verify).Originally Posted by mr_miles ↑i have the kit with the stalk on the left side.
Hmm...I do plan on replacing the steering wheel in the future (not near), if you think it's possible to somehow use the OEM cruise with an aftermarket wheel, I wouldn't mind the swap at all.
The OEM one will definitely not work with an aftermarket wheel. The Rostra one will, since it mounts to the steering column cover, rather than within the wheel.Originally Posted by mr_miles ↑Hmm...I do plan on replacing the steering wheel in the future (not near), if you think it's possible to somehow use the OEM cruise with an aftermarket wheel, I wouldn't mind the swap at all.
Oh well, I'll just go with the OEM until I swap wheels. then I can always adapt to something different later on. You're going to have a box full of Yaris electrical goodies from me, lol. Still have a few other things to send to you :p
LOL. Sounds like a plan.Originally Posted by mr_miles ↑Oh well, I'll just go with the OEM until I swap wheels. then I can always adapt to something different later on. You're going to have a box full of Yaris electrical goodies from me, lol. Still have a few other things to send to you :p
Hi,
is any chance to work CC in Yaris made in France with 1.0 vvti 1kr-fe engine?
I can get VIN if it could help...
Best regards
is any chance to work CC in Yaris made in France with 1.0 vvti 1kr-fe engine?
I can get VIN if it could help...
Best regards
The Toyota OEM cruise control definitely will not work with the 1.0L French made Yaris, but the Rostra kit that mr miles and I were discussing above may. Once I have it in hand and check some things relative to the wiring diagrams for the 1kr-fe I will let you know.Originally Posted by william7 ↑Hi,
is any chance to work CC in Yaris made in France with 1.0 vvti 1kr-fe engine?
I can get VIN if it could help...
Best regards
I looked in my yaris speedometer and it has a CC lights.
Is it a 2007 Terra, like your info shows, or is it a 2012?Originally Posted by william7 ↑I looked in my yaris speedometer and it has a CC lights.
Also, it may be that the same speedometer is used on the 1.0 L and 1.33 L Yaris.
I forgot about changing my profile.
I have 2012 Yaris Luna 1.0 L
I have 2012 Yaris Luna 1.0 L
OK - That makes more sense as to why it has the light for cruise control. According to the Toyota wiring diagrams for the French made Yaris, only the 1.33L has the cruise control function built in, so it must be that they use the same speedometer for the various engine configurations.Originally Posted by william7 ↑I forgot about changing my profile.
I have 2012 Yaris Luna 1.0 L
Just picked up my 2013 Yaris - will want to do this down the road, so it is time to ask: Anybody know the differences between 2012 and 2013 for cruise control install?
No difference at all.Originally Posted by jelo ↑Just picked up my 2013 Yaris - will want to do this down the road, so it is time to ask: Anybody know the differences between 2012 and 2013 for cruise control install?
Great - Thanks!
Thank you CTScott, richard rsp & 12BusYaris,
I just recently bought my second Yaris(2012). My daughter took the first one (2009) to college. I was disappointed that it didn't have cruise control seeing as it had all the other power options. I was thrilled when I found this site and learned how easy it was to remedy. I bought the stalk online for about $58 with shipping and it took about 30 minutes tops to install. Just need to cut the hole in the cover piece. Anyone have measurements for that? Thanks again!
I just recently bought my second Yaris(2012). My daughter took the first one (2009) to college. I was disappointed that it didn't have cruise control seeing as it had all the other power options. I was thrilled when I found this site and learned how easy it was to remedy. I bought the stalk online for about $58 with shipping and it took about 30 minutes tops to install. Just need to cut the hole in the cover piece. Anyone have measurements for that? Thanks again!
I still haven't had a chance to get my hands on a 2012 to take the measurements. I actually have a batch of the 2012+ cover pieces on order, and should have them in hand next week.Originally Posted by ksejrs ↑Thank you CTScott, richard rsp & 12BusYaris,
I just recently bought my second Yaris(2012). My daughter took the first one (2009) to college. I was disappointed that it didn't have cruise control seeing as it had all the other power options. I was thrilled when I found this site and learned how easy it was to remedy. I bought the stalk online for about $58 with shipping and it took about 30 minutes tops to install. Just need to cut the hole in the cover piece. Anyone have measurements for that? Thanks again!
Also, with the cruise control stalks and the clutch switches, I always have some on hand and sell them for a fraction of retail.
^Nice!
By the way, I recently acquired a batch of the replacement covers for the side of the 2012-2013 steering wheel, which have the hole for the cruise control stalk. They are $5 shipped in the US.
By the way, I recently acquired a batch of the replacement covers for the side of the 2012-2013 steering wheel, which have the hole for the cruise control stalk. They are $5 shipped in the US.
Can I do this to a 2007 Yaris Liftback with the power option added? I have everything but cruise.
Yes. Below is a link to my DIY for 06-11 Yaris. I carry all of the part required if you are interested in installing it:Originally Posted by misterwolfe ↑Can I do this to a 2007 Yaris Liftback with the power option added? I have everything but cruise.
DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
Thank you! Though with requiring to wire up my steering column, that may be my roadblock. Will look into this. (I am colorblind, and at the mercy of my father doing these for me.)Originally Posted by CTScott ↑Yes. Below is a link to my DIY for 06-11 Yaris. I carry all of the part required if you are interested in installing it:
DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
If it is relatively easy, I'll totally buy an entire kit from ya. Also, hoping for keyless entry soon too!
Hi everyone, I am new here, and from australia.
I have a Yaris YR 5 door (base model, 1.3 manual)
I have "acquired" a OEM cruise control stalk and cable, I can fit it into the steering wheel no worries, the cruise light comes on, though can not set the speed. Would this be because of the clutch switch?. I have tried Toyota, and they werent really much help. Though they did come back with a $90 part. I do have to push the clutch in to start the vehicle to begin with though, so i would assume it would already have one?.
Could someone please shed some light for me?
THanks.
I have a Yaris YR 5 door (base model, 1.3 manual)
I have "acquired" a OEM cruise control stalk and cable, I can fit it into the steering wheel no worries, the cruise light comes on, though can not set the speed. Would this be because of the clutch switch?. I have tried Toyota, and they werent really much help. Though they did come back with a $90 part. I do have to push the clutch in to start the vehicle to begin with though, so i would assume it would already have one?.
Could someone please shed some light for me?
THanks.
There are two clutch switches on a manual transmission Yaris. The pre-installed on is the push the clutch to the floor to start the car one. The one you have to add for cruise control works the opposite way. It replaces the stopper bolt that the clutch arm rests against (when your foot is not on it) and it signals the ECM when you barely touch the clutch pedal (to prevent the revving that would occur if the clutch was pressed when cruise was applying throttle).Originally Posted by Licky ↑Hi everyone, I am new here, and from australia.
I have a Yaris YR 5 door (base model, 1.3 manual)
I have "acquired" a OEM cruise control stalk and cable, I can fit it into the steering wheel no worries, the cruise light comes on, though can not set the speed. Would this be because of the clutch switch?. I have tried Toyota, and they werent really much help. Though they did come back with a $90 part. I do have to push the clutch in to start the vehicle to begin with though, so i would assume it would already have one?.
Could someone please shed some light for me?
THanks.
[QUOTE=CTScott;615019]I recently obtained the wiring diagrams for the 2012 Yaris. Much of the wiring and connectors remain the same as the second generation Yaris. This is the case for cruise control, so 2012 Yaris owners can DIY cruise control using the same OEM stalk.
For the 2012 the wiring is the same as that of the 2009-2011 Yaris, where the wiring from the ECM to the steering column is (theoretically) there. Also, the 2012 Yaris has the cruise control "On" and "Set" indicators built into the instrument cluster.
CTScott Hello, if you have wiring diagrams for the 2012 Yaris, you help us and us with them? Please much.
For the 2012 the wiring is the same as that of the 2009-2011 Yaris, where the wiring from the ECM to the steering column is (theoretically) there. Also, the 2012 Yaris has the cruise control "On" and "Set" indicators built into the instrument cluster.
CTScott Hello, if you have wiring diagrams for the 2012 Yaris, you help us and us with them? Please much.
Which is code oem cruise control stalk for Toyota Yaris ?
Code for cruise control stalk toyota yaris is 84632-34011 or 84632-0F010, can you help me ?
anyone can help me?
Hello everyone. I bought the pieces of picture 1, I installed according to picture 2 3.4, but the result was negative, to me does not work. I 1ND-TV engine, 1.4 D4D 66kW respectively. Can someone help me? You need to do something else than I did? Have to change terminals 1 and 2 of the 4-pin connector in the 10 pin?
5 attachments not included in this copy
Originally Posted by geoded ↑Hello everyone. I bought the pieces of picture 1, I installed according to picture 2 3.4, but the result was negative, to me does not work. I 1ND-TV engine, 1.4 D4D 66kW respectively. Can someone help me? You need to do something else than I did? Have to change terminals 1 and 2 of the 4-pin connector in the 10 pin?
You have everything installed in the proper place, but according to the wiring diagrams the 1ND-TV Yaris does not support cruise control.
Check the connector on the other end of the spiral cable, which is located under the cover for the lower part of the steering column. The question is if the two wires are present there that would connect to the cruise control stalk wires under the airbag.
I understand the need to loosen the screw from the one in picture 1 and picture 2, but do not know exactly what wires need to see, you have a picture of what should I see there?
2 attachments not included in this copy
Is it worth trying to move to Terminal 1 and 2 of the 4-pin connector at position 1 and 2 of the 10-pin connector? or is in vain? still will not go anything? The blue wire is the ground wire and do not know where to put it if put in place the terminal 1 of the 4-pin plug.
1 attachment not included in this copy
No. Where you have the connector is correct for ones that are cruise control equipped.Originally Posted by geoded ↑Is it worth trying to move to Terminal 1 and 2 of the 4-pin connector at position 1 and 2 of the 10-pin connector? or is in vain? still will not go anything? The blue wire is the ground wire and do not know where to put it if put in place the terminal 1 of the 4-pin plug.
I am looking for the connector on the left in the photo below. You will remove the two screws behind the steering wheel and the one by the tilt lever to remove the lower cover.Originally Posted by geoded ↑I understand the need to loosen the screw from the one in picture 1 and picture 2, but do not know exactly what wires need to see, you have a picture of what should I see there?
Picture not included in this copy
Connector 1? or two, or three ...... ? I think the connector one you mean but I want to call you. Right?
1 attachment not included in this copy
You do not have the wiring diagram for 1.4 d4d? Although I know that the same engine Auris 1.4 D4D has cruise control, I hope someone will hear us and we may find a solution in the future, I just have to have patience.
It is connector 1 that we need to look at. I do have the D4D wiring diagrams, where the "engine control" one does not show cruise control, whereby the wiring diagrams for the 1.33L gas engine does. I don't have the wiring diagrams for the Auris, but I do see in the parts catalog that it uses a different ECM.Originally Posted by geoded ↑You do not have the wiring diagram for 1.4 d4d? Although I know that the same engine Auris 1.4 D4D has cruise control, I hope someone will hear us and we may find a solution in the future, I just have to have patience.
Thanks a lot for your help CTScott.
CTScott,
I am new to this forum. My daughter in Indiana just purchased a 2012 Yaris Sedan without cruise control. I noticed from the pictures she sent, that the cluster is mounted in the center of the dash vs behing the steering wheel as I am seeing in the pictures in this thread. I am guessing that Toyota did a mid-year refresh of the vehicle in 2012 and that she has the older version.
I have two questions...
1) Can I add OEM cruise to her car using your instructions?
2) If so, which directions do I use. The ones for 2009-2011 or the ones for 2012?
I have added OEM cruise to another daughters 2010 Cobalt. This looks much easier than that.
Thanks,
Fred
I am new to this forum. My daughter in Indiana just purchased a 2012 Yaris Sedan without cruise control. I noticed from the pictures she sent, that the cluster is mounted in the center of the dash vs behing the steering wheel as I am seeing in the pictures in this thread. I am guessing that Toyota did a mid-year refresh of the vehicle in 2012 and that she has the older version.
I have two questions...
1) Can I add OEM cruise to her car using your instructions?
2) If so, which directions do I use. The ones for 2009-2011 or the ones for 2012?
I have added OEM cruise to another daughters 2010 Cobalt. This looks much easier than that.
Thanks,
Fred
Originally Posted by fredansandy ↑CTScott,
I am new to this forum. My daughter in Indiana just purchased a 2012 Yaris Sedan without cruise control. I noticed from the pictures she sent, that the cluster is mounted in the center of the dash vs behing the steering wheel as I am seeing in the pictures in this thread. I am guessing that Toyota did a mid-year refresh of the vehicle in 2012 and that she has the older version.
I have two questions...
1) Can I add OEM cruise to her car using your instructions?
2) If so, which directions do I use. The ones for 2009-2011 or the ones for 2012?
I have added OEM cruise to another daughters 2010 Cobalt. This looks much easier than that.
Thanks,
Fred
Hi Fred,
Sedans did not get an update in 2012 as liftbacks did, so for your daughter's car the my 2009-2011 directions are the ones you will follow.
The pin that goes into the spring clips has a groove in it that the spring clip latches onto, so you are trying to open the legs on the clip to release it from the groove.Originally Posted by JZA80 ↑I'm trying to remove a 2012 Yaris steering wheel airbag. I can see the 3 spring clips but cannot understand how you release them, does it require a special tool? can anyone help explain?
How do you do, it is called takumu. It has ridden on Japanese use of 12 models. There is no cruise control in vitz of Japanese use, and I am troubled by it. It did not operate, even if it post-installed the cruise control switch. If it investigates, there is no wiring of a spiral cable to the point. Who has a wiring diagram of the cruise control of yaris of 12 models? Or please let me know wiring to a computer. Thank you for your consideration.
Welcome! It is always nice to hear from people from the birthplace of the Yaris (Vitz). I believe that the third generation Vitz still does not support cruise control. The European third generation Yaris (only the one with the 1.33L engine) now does, but not the Japanese one. The reason I think this is that the parts catalog for the Japanese Vitz does not list any parts related to cruise control.Originally Posted by takumu0307 ↑How do you do, it is called takumu. It has ridden on Japanese use of 12 models. There is no cruise control in vitz of Japanese use, and I am troubled by it. It did not operate, even if it post-installed the cruise control switch. If it investigates, there is no wiring of a spiral cable to the point. Who has a wiring diagram of the cruise control of yaris of 12 models? Or please let me know wiring to a computer. Thank you for your consideration.
On the ones that do have it, Pin 60 of ECM connector A72 is where one wire of the stalk connects to and the other wire connects to chassis ground.
1 attachment not included in this copy
Mr. CTScott, thank you. My car is 1 KR-FE engine. Somehow, the form of the connector of A70 was different. It was connector-shaped [ of the same engine computer as yaris(es) from 2006 to 2011 ]. The wiring which is already different is stuck in the wiring place of the cruise control of 2011 models. It was troubled.
Rostra is apparently smoking crack on this one. Installation on a 3rd gen Yaris does not require popping the hood for any reason other than to temporarily disconnect the battery for safety reasons.Originally Posted by spammenot66 ↑hi CTScott,
Are you still selling anymore of your kits? I've brought a rostra kit from amazon and the instructions are confusing. I've followed everything up to the ECM part of the instruction. I have a 2012 Yaris 5D LE. How do i determine whether my car has "CLUTCH ECM HARNESS" or not? Where the heck is the "ENGINE COMPARTMENT ON THE PASSENGER SIDE FIREWALL"
Any help would be greatly appreciated
My kits are still for sale and for 3rd gens I also stock the little cover for the side of the steering wheel, so no drilling is even required.
Originally Posted by spammenot66 ↑good to know i've wasted ALOT of time opening everything trying to figure that part out. Everything about their stupid instruction seems wrong.
1)"For 2012 Yaris: Using a "Torx" Driver, push in the 3 snap rings to disengage it from the 3 pins" - After checking out this site, i realized a flat head screw driver should do the trick.
2)The template cut didn't make sense - 1.5 inch hole saw is not needed. It was simpler to just use a razor to cut out a rectangle for the piece. As for the 1/4 pilot hole, i never understood what it was for.
3) If you're right about the "BLACK ECM CONNECTOR C20 IN THE ENGINE COMPARTMENT ON THE PASSENGER SIDE FIREWALL", that's more wrong info from them for page 6 (steps 1-3)
Their instructions are the worst (http://www.rostra.com/manuals/250-1836_Form5370A.pdf). This was suppose to be specifically for the 2012 yaris. I see that you have also mentioned similar instructions within the forum matching theirs on page 7 (steps 5 to 7).
Do i still need to do this? BTW, can you PM me on how to buy from you?
The page 7 info is completely wrong for a 2012. The 2012+ are all prewired. The only thing that would have to be done is to install and plug in (connector is present) the clutch switch for a manual transmission Yaris.
So, for 2012+ just install the stalk and you're done for an auto. For a manual, also install the clutch switch. All wiring is present, so it is just a matter of plugging them in.
Hi All,
Fitted the Scott's CC kit on Yaris 2013, 1.33 1nr-fe CVT.
Touch 'n Go head unit didn't ask for security code after the battery disconnect, also all settings were not reset (radio, BT, sound settings).
To get out the airbag from the wheel with side gear switches - is real pain, took me like 40 min.
CC works like a charm :), the plastic cover panel didn't fit though, waiting for Scott to figure that out.
Update: Scott emailed me the partnumber of the cover panel and I got it from the local dealer for $10 with taxes (btw Scott had refunded me the wrong part cost at the moment I've reported it)
Picture not included in this copy
Fitted the Scott's CC kit on Yaris 2013, 1.33 1nr-fe CVT.
Touch 'n Go head unit didn't ask for security code after the battery disconnect, also all settings were not reset (radio, BT, sound settings).
To get out the airbag from the wheel with side gear switches - is real pain, took me like 40 min.
CC works like a charm :), the plastic cover panel didn't fit though, waiting for Scott to figure that out.
Update: Scott emailed me the partnumber of the cover panel and I got it from the local dealer for $10 with taxes (btw Scott had refunded me the wrong part cost at the moment I've reported it)
Picture not included in this copy
Does anyone know if this will work on my 2013 1.4 d4d ?
Thanks
Thanks
No. Unfortunately only the 1.33L European Yaris supports cruise control.Originally Posted by er6nphil ↑Does anyone know if this will work on my 2013 1.4 d4d ?
Thanks