Liu997Original postHicksville, LI · Apr 25, 2009#1I used this DIY on Yarisworld
DIY (08' USDM Liftback): ESUSE Fog Light Install v2.0 I have the same problem of that the switch led won't turn off even if you turn off the car.
There was an explanation but I didn't quite understand. Where do you get the red wire and the white wire from?. I currently followed exactly as says. Thanks in advance.
Replies 57
Liu997Thread starterHicksville, LI · Apr 25, 2009#2no one used this diy?
1NZYaris1New Zealand · Apr 25, 2009#3Nope i used the factory PDF.
Who's fog light kit are you useing.
Liu997Thread starterHicksville, LI · Apr 25, 2009#4I got one off of ebay, the same exact one from the DIY thats why I chose that one. But now My square light doesn't go off. This is 🙄
cyberfroggTX · Apr 25, 2009#5 Originally Posted by
Liu997 ↑ I used this DIY on Yarisworld
DIY (08' USDM Liftback): ESUSE Fog Light Install v2.0 I have the same problem of that the switch led won't turn off even if you turn off the car.
There was an explanation but I didn't quite understand. Where do you get the red wire and the white wire from?. I currently followed exactly as says. Thanks in advance.
You're not alone in this. I followed that DIY exactly the same and the switch led won't turn off either... =/
Liu997Thread starterHicksville, LI · Apr 25, 2009#6^ Wad u do? Just leave them on?.... Actually that isn't much of a problem cause that puny led will probably never drain out the battery even if left on 24/7. But im just uncomfortable knowing a light is still on in my car.🤷
Liu997Thread starterHicksville, LI · Apr 26, 2009#7heh, guess no one has any suggestions 🆘
LtNoogieWest Hills, CA · Apr 26, 2009#8Liu, what exactly is the problem? Can you take a picture? I don't have foglights but I know a little about the electrical stuff.
cyberfroggTX · Apr 26, 2009#9 Originally Posted by
Liu997 ↑ ^ Wad u do? Just leave them on?.... Actually that isn't much of a problem cause that puny led will probably never drain out the battery even if left on 24/7. But im just uncomfortable knowing a light is still on in my car.🤷
Yeah. For now I just left it on. It doesn't drain the battery but yeah I know its annoying for me as well.. lol
I'm just waitin for CTScott's reply... He's tryin to help me..
yarisugiハワイ · Apr 26, 2009#10Use that DIY if you want to turn on the foglight indicator in the instrument panel AND the light on the foglight switch that came with the kit.
Photo towards the end of that link from tk-421(also pictured below) has red and white wires.
The foglight kit you bought has different color wires from his, but he is just telling you where to locate constant power and acc/switched power on the fuse box.
If you're installing the foglights using only the contents of the kit, follow the picture above for the location of CONSTANT POWER. If you want the light on the foglight switch to turn off when the key is out of the ignition, then follow the picture below.
Use the wire for the acc/switched power and instead of plugging it into the location that was shown in the picture above, modify a connector, crimp it to the red wire, and insert it in the location where I had circled in yellow. What I did was use a connector like in the picture below and smashed it flat so I can insert it into that slot that I circled in yellow, not disturbing the existing wire that's plugged in there. This way, if you turn off the car, the light on the foglight switch will turn off, too. Since the light on the foglight switch doesn't draw much power, it's should be safe to insert it there without adding a fuse.
Sequence:
Turn on ignition - rectangular light remains off, foglight symbol turns on. Foglights are still OFF.
Push switch - rectangular light turns on and foglight symbol remains on. Foglights are ON.
Push switch again - rectangular light turns off, foglight symbol still on. Foglights are OFF.
Remove key from ignition - both lights on foglight switch are off. Foglights are OFF.
Sleep in peace.
Liu997Thread starterHicksville, LI · Apr 26, 2009#11Wait the kit I used didn't have no red wire, do you mean the wires I connected under the steering wheel. I still don't know much about electrics cause this is my first DIY.
cyberfroggTX · Apr 27, 2009#12Ah I would like to know this too! I'm thinking the green wire under the steering wheel is the red wire and the blue wire is the white wire in this case..
yarisugiハワイ · Apr 27, 2009#13 Originally Posted by
Liu997 ↑ Wait the kit I used didn't have no red wire, do you mean the wires I connected under the steering wheel. I still don't know much about electrics cause this is my first DIY.
Are you trying to wire the foglights so that the foglight indicator on the instrument panel lights up, too? If you are, then disregard my posts in this thread.
If you're not, then don't connect anything that's under your steering wheel. You don't even have to remove the steering column plastics.
The kit you bought has different color wires from other kits that other people bought. So, in your case there is NO red wire. It's probably a different color. You have to find out which wire on the switch is the CONSTANT POWER and which wire is the ACC/SWITCHED POWER.
The two wires in the picture are coming directly from the harness that goes to your foglight switch.
Liu997Thread starterHicksville, LI · Apr 27, 2009#14 Originally Posted by
yarisugi ↑ Are you trying to wire the foglights so that the foglight indicator on the instrument panel lights up, too? If you are, then disregard my posts in this thread.
If you're not, then don't connect anything that's under your steering wheel. You don't even have to remove the steering column plastics.
The kit you bought has different color wires from other kits that other people bought. So, in your case there is NO red wire. It's probably a different color. You have to find out which wire on the switch is the CONSTANT POWER and which wire is the ACC/SWITCHED POWER.
The two wires in the picture are coming directly from the harness that goes to your foglight switch.
Yea I'm wiring so the the fog indicator comes on. What would I do then. Modify the switch?
CTScottUSA, CT · Apr 27, 2009#15 Originally Posted by
Liu997 ↑ Yea I'm wiring so the the fog indicator comes on. What would I do then. Modify the switch?
Take a look at the end of this thread:
need help: foglight indicator - where are the wires? I have been trying to help cyberfrogg with the same issue.
Liu997Thread starterHicksville, LI · Apr 27, 2009#16That clears things up a bit, Im glad I have a circuit writer pen 😁.
Also what is the diode that I must remove.
CTScottUSA, CT · Apr 27, 2009#17 Originally Posted by
Liu997 ↑ That clears things up a bit, Im glad I have a circuit writer pen 😁.
Also what is the diode that I must remove.
The diode is the orange and black device.
Liu997Thread starterHicksville, LI · Apr 28, 2009#18 Originally Posted by
CTScott ↑ The diode is the orange and black device.
So I just solder it off right? And then my switch will work? I mean with the other modifications
Ok check back with u when I do this thanks?
CTScottUSA, CT · Apr 28, 2009#19 Originally Posted by
Liu997 ↑ So I just solder it off right? And then my switch will work? I mean with the other modifications
Ok check back with u when I do this thanks?
Correct. With all of the mods done, it should work like the OEM switch.
Liu997Thread starterHicksville, LI · Apr 30, 2009#20Ok, I have a problem. Since I just got my relay need to do the DIY, I just found out of the problem. I realized that my switch doesn't even work at all. The minute I plug in the foglight relay my fogs light up, switch on "off" or on "on". But when I turn on the headlights or the panel lights the fogs turn off regardless of switch setting. I may have wired it up wrong. Any help will be accepted. Thanks in advance.
CTScottUSA, CT · Apr 30, 2009#21 Originally Posted by
Liu997 ↑ Ok, I have a problem. Since I just got my relay need to do the DIY, I just found out of the problem. I realized that my switch doesn't even work at all. The minute I plug in the foglight relay my fogs light up, switch on "off" or on "on". But when I turn on the headlights or the panel lights the fogs turn off regardless of switch setting. I may have wired it up wrong. Any help will be accepted. Thanks in advance.
If I understand correctly, you had it wired before with the aftermarket relay. You now changed the wiring to use the OEM relay mounted in the fuse panel?
Liu997Thread starterHicksville, LI · Apr 30, 2009#22No I never used the aftermarket relay, I followed the DIY exactly, which says to use the OEM foglight relay. I've just been waiting for the relay I ordered and ebay. I just got it now, Plugged it in and the foglight come on immediately. I even tried disconnecting the switch and the foglights are still on 😕. That is really weird. But the foglights only seem to come on if the headlights and the panel lights are closed.
CTScottUSA, CT · Apr 30, 2009#23 Originally Posted by
Liu997 ↑ No I never used the aftermarket relay, I followed the DIY exactly, which says to use the OEM foglight relay. I've just been waiting for the relay I ordered and ebay. I just got it now, Plugged it in and the foglight come on immediately. I even tried disconnecting the switch and the foglights are still on 😕. That is really weird. But the foglights only seem to come on if the headlights and the panel lights are closed.
OK. To verify:
1. Under the hood - The black wire is connected to the grounding bolt and the red wire is connected to Pin 1 or 2 per the DIY picture:
Picture lost · img252.imageshack.us 2. Under the dash - If you disconnect the wires that your connected per the DIY picture below from Pin 3 and Pin 4 do the lights go off and stay off with the headlights on or off?
Picture lost · img258.imageshack.us Liu997Thread starterHicksville, LI · Apr 30, 2009#24wait for the first pic, i connected it to the pin directly left of it, which i think is pin 2, is that ok?
And for pic 2 it is blue to white wire right, and green to Yellow?
Liu997Thread starterHicksville, LI · Apr 30, 2009#25BTW, thanks a lot for helping idk what I would do if I didn't have anyone to help. 🙇
CTScottUSA, CT · Apr 30, 2009#26 Originally Posted by
Liu997 ↑ wait for the first pic, i connected it to the pin directly left of it, which i think is pin 2, is that ok?
And for pic 2 it is blue to white wire right, and green to Yellow?
Pin 2 is fine.
For picture 2, try disconnecting your wires from the white and yellow, just to make sure that the relay is OK. With yours disconnected the fogs should not light at all.
Liu997Thread starterHicksville, LI · Apr 30, 2009#27Wait, what happends when you try to run the foglights with no relay place in. Cause I put in the foglights before I got the relay and accidentaly pressed it, and there was a buzzing sound comming from under the dash, but I quickly disabled it.
Also how do you disassemble the switch, I don't want to pull off pieces and break some plastic.
CTScottUSA, CT · Apr 30, 2009#28 Originally Posted by
Liu997 ↑ Wait, what happends when you try to run the foglights with no relay place in. Cause I put in the foglights before I got the relay and accidentaly pressed it, and there was a buzzing sound comming from under the dash, but I quickly disabled it.
Also how do you disassemble the switch, I don't want to pull off pieces and break some plastic.
If the switch was wired as per the OEM one turning it on without the relay wouldn't be a problem.
The switch housing should have two tabs, one on either side, just above the connector. You have to press them in while pulling the top from the connector end.
Liu997Thread starterHicksville, LI · May 1, 2009#29Reviewed everything you said still having trouble.
Currently this is what happening. Foglight relay installed, Switch NOT modified.
Foglight switch off, all car lights shut off --- Foglights On, Square Light On
Foglight switch on, all car lights shut off --- Foglights On, Square Light On
Foglight switch off, Panel Lights turned on --- Foglights off, square light off
Foglight switch on, Panel Lights turned on --- Foglights off, square light off
Foglight switch off, headlights turned on --- Foglights off, square light off
Foglight switch on, headlights turned on --- Foglights off, square light off
I'm, going to review the DIY can't be having this much trouble if I followed it exactly.
Liu997Thread starterHicksville, LI · May 1, 2009#30I may have had a problem in this step, what does this mean.
"
Now we must finish modifying the aftermarket harness. Cut the 2 black and 1 solid blue wire as well. The blue/green wire will not be used. Remove the electrical tape holding the end of the harness together. Once everything is pulled apart you should have black, solid blue and solid green wires left in the harness. Use a butt splice to reconnect the 2 black wires. (sorry I forgot to take pictures of the final modified harness):"
I connected the black wire to each other would that be right?
1NZYaris1New Zealand · May 1, 2009#31The problem is now your switch , mod as shown in diy .
or buy the factory stalk for $77.00US 👍
CTScottUSA, CT · May 1, 2009#32 Originally Posted by
Liu997 ↑ I may have had a problem in this step, what does this mean.
"
Now we must finish modifying the aftermarket harness. Cut the 2 black and 1 solid blue wire as well. The blue/green wire will not be used. Remove the electrical tape holding the end of the harness together. Once everything is pulled apart you should have black, solid blue and solid green wires left in the harness. Use a butt splice to reconnect the 2 black wires. (sorry I forgot to take pictures of the final modified harness):"
I connected the black wire to each other would that be right?
I have no idea from the pics what the second black wire is for. If you look at the switch itself, it has one black wire, which is the ground for the lighting circuit. If you follow the wires from the switch, Blue goes to D3-pin3, Green next to blue goes to D3-pin4, the other green goes to the accessory lighting wire, and black goes to ground.
Liu997Thread starterHicksville, LI · May 1, 2009#33 Originally Posted by
CTScott ↑ I have no idea from the pics what the second black wire is for. If you look at the switch itself, it has one black wire, which is the ground for the lighting circuit. If you follow the wires from the switch, Blue goes to D3-pin3, Green next to blue goes to D3-pin4, the other green goes to the accessory lighting wire, and black goes to ground.
Damn, I don't know. I'm just going to modify the switch first, then see what happens.
Wait also what is the point of cutting of the green wire closest to the black?
CTScottUSA, CT · May 1, 2009#34 Originally Posted by
Liu997 ↑ Damn, I don't know. I'm just going to modify the switch first, then see what happens.
Wait also what is the point of cutting of the green wire closest to the black?
Also, check the wires and make sure that from the switch connector that they connect as I mentioned above. They need to be that way for the modded switch to work.
Liu997Thread starterHicksville, LI · May 3, 2009#35 Originally Posted by
CTScott ↑ I have no idea from the pics what the second black wire is for. If you look at the switch itself, it has one black wire, which is the ground for the lighting circuit. If you follow the wires from the switch, Blue goes to D3-pin3, Green next to blue goes to D3-pin4, the other green goes to the accessory lighting wire, and black goes to ground.
You mean D4 right? I just checked and there was no D3 pin under the steering wheel
CTScottUSA, CT · May 3, 2009#36 Originally Posted by
Liu997 ↑ You mean D4 right? I just checked and there was no D3 pin under the steering wheel
Correct - D4 (typo on my part).
Liu997Thread starterHicksville, LI · May 3, 2009#37Ok my fogs are finally working. Are the foglights supposed to light up even when the light stalk is switched off? Mine only light up when the panel or headlights are on.
Also I got it to work without soldering the two jumpers, but the square light won't go on. The reason I did that is because when I soldered the jumpers, the foglights were on regardless of switch positon. And when I pressed it a buzzing sound came from under the steering wheel.
And, I couldn't find the diode on mine. Heres how my switch looks like currently
CTScottUSA, CT · May 3, 2009#38Fogs only come on with the low beam headlights.
You have to also cut/desolder the connection between the blue-green and green-black pads (and add those two jumpers) for the lighting to work correctly.
Liu997Thread starterHicksville, LI · May 4, 2009#39 Originally Posted by
CTScott ↑ Fogs only come on with the low beam headlights.
You have to also cut/desolder the connection between the blue-green and green-black pads (and add those two jumpers) for the lighting to work correctly.
By that you mean this right?
CTScottUSA, CT · May 4, 2009#40 Originally Posted by
Liu997 ↑ By that you mean this right?
Correct.
cyberfroggTX · May 6, 2009#41Liu, did it work? I've been wanting to try it out but I haven't had the chance.
Liu997Thread starterHicksville, LI · May 6, 2009#42Sorry, didn't have time. I have so much work to do lately. I will try it this wkend, ill get back to you
cyberfroggTX · May 7, 2009#43okay thanks. I'm really hoping this works.
Liu997Thread starterHicksville, LI · May 7, 2009#44Tried this, This is the most I can explain lets go With the switch on
1. The minute I plugged it in all panel lights come on.
2. The lights come on in addition to a buzzing sound coming from under the steering wheel, most likely a relay or near the fuse box.
3. When I turn the panel lights on I see a spark (because I plugged it in without the cover but shouden't be a problem.) and the jumper listed below disconnects. I have done everything you have said.
4. See picture.
CTScottUSA, CT · May 7, 2009#45Move the jumper that is over the "es" of resistor (at the top right) to the "o" of resistor.
Is the solder and trace under it gone between all of the three groups of two switch contacts?
Liu997Thread starterHicksville, LI · May 9, 2009#46The same thing happens this is a real picture on my switch. Mind the circuit writer, that is because I accidentally cut off a trace
CTScottUSA, CT · May 9, 2009#47 Originally Posted by
Liu997 ↑ The same thing happens this is a real picture on my switch. Mind the circuit writer, that is because I accidentally cut off a trace
Getting close. Look at the picture below. This is what I mean about separating the three groups of two contacts for the switch. This isolates the switch circuit from the lighting circuit.
Also, since you used non-insulated wire for your jumpers, make sure that they do not touch anywhere except for at the ends.

Liu997Thread starterHicksville, LI · May 9, 2009#48but should the two groups of three contacts touch or should nothing touch anything else
Liu997Thread starterHicksville, LI · May 9, 2009#49The picture is how my switch is now. Still not working
Now everything functions like normal but the square light doesn't turn on no matter what.
CTScottUSA, CT · May 9, 2009#50 Originally Posted by
Liu997 ↑ The picture is how my switch is now. Still not working
Now everything functions like normal but the square light doesn't turn on no matter what.
Does the Fog light symbol light up?