I'd say we could get 10% under the curve easily, probably slightly more. Peak piwer increase I would expect 8-10%. You make more power with timing than you do with boost. LtNoogie is seeing single digit ignition advance under load. If we could get that up to where is should be, and add some fue,l the gains would be there. There is a lot of potential.Originally Posted by Loren ↑I'll believe that when I see it.
Let me qualify that. The bolt-on, out-of-the box Blitz SC kit with fully tuned and optimized fuel and spark. The initial installation is only good for about 25%, or 25-30 hp. No way is optimizing the fuel and spark going to DOUBLE that. You'll find another 3-8%... maybe as much as 10% or so, just like you would by tuning the car without the SC. That's the factory's margin of safety that you're playing with.
Now, you might see something close to that with a lot of OTHER additional mods, like a complete free-flowing intake, larger TB, better flowing intake manifold, some head work, a good header and a complete free-flowing exhaust. But, that's an awful lot of other stuff that doesn't really fall into the category of "fuel and spark tuning". And, even with all of that, I still don't think you're going to DOUBLE the output of the SC without raising the level of boost.
Another S/C'd member worried about his AFR
182 posts · 47,610 views · page 4 of 4
Replies continued
WORDOriginally Posted by camelll ↑the car should have come from the factory with the power the blitz puts out
Where did mount yours? Is there an ideal spot? Saw the pic of staypuft's on the battery, but I have so much room up in front of the CAI... is that too far for the hose to reach the pcv valve?Originally Posted by camelll ↑glad I got the oil catch.
niiiiiiiice, and that shyt is goin down my intake track? 🤮Originally Posted by camelll ↑It was just a nasty hodgepodge of shit and I still cannot get that smell out of my nose.
No idea what I'll see 🤷 since 5000 mi. I been on full synthetic, changed every 5k. At almost 40k now with some 3500 on the charger, I hope mine won't be so disgusting
The DIY can in the link is very compact, its clever also, but I think I'll just get a cheap metal one, I've been on a chrome kick lately 😁
Can someone recommend a good OBD II data logging software package? I was making a few freeway runs last night in 3rd gear to collect data and saw some surprising results on the ScanGauge. Not bad readings, surprising readings.
It's too hard to videotape the gauges and the ScanGauge due to the shakiness of the camera mounts I have tried.
I was monitoring Open/Closed loop state, RPM, Throttle Position, and Ignition timing. What I saw was that the car went into Open Loop during acceleration more often than expected with the S/C turned on AND when it was turned off. This is happening before hitting 50% throttle position.
It's too hard to videotape the gauges and the ScanGauge due to the shakiness of the camera mounts I have tried.
I was monitoring Open/Closed loop state, RPM, Throttle Position, and Ignition timing. What I saw was that the car went into Open Loop during acceleration more often than expected with the S/C turned on AND when it was turned off. This is happening before hitting 50% throttle position.
I'm a big fan of a good ELM327 based reader (I like the ElmScan 5, but just make sure it's using a real ELM327 and not a knockoff) and PCMSCAN. Seems to work well on my Mazda and the Yaris.
Well now you bastards have got me obsessing too! (not difficult) 😆
Today I also saw one open loop status that fell outside what you all are describing as normal triggering conditions (DFCO and WOT)... it was under boost and acceleration at 32 TPS and 15 ign timing, and persisted for like 10 seconds... wtf.
Here's one random thought, though I don't know if it means anything at all. According to the wiring diagrams the s/c fuel controller does not wire into the throttle position sensor (TPS) located on the throttle body itself (ECM terminal VTA1) but rather into the accelerator pedal position sensor located on the pedal (VPA). Other than that it hooks up to RPM, ignition switch, injectors 1-4, and MAF (VG). The two other wires go to ground and activation switch.
Since the ECM uses the VTA1 data direct from the TPS to calculate everything from valve timing to long- and short-term fuel trims, I don't know what to think of that! I guess the fuel controller is altering the VPA signal sent to the TPS, and thereby manipulating the VTA1 signal then sent to the ECM?
Today I also saw one open loop status that fell outside what you all are describing as normal triggering conditions (DFCO and WOT)... it was under boost and acceleration at 32 TPS and 15 ign timing, and persisted for like 10 seconds... wtf.
Here's one random thought, though I don't know if it means anything at all. According to the wiring diagrams the s/c fuel controller does not wire into the throttle position sensor (TPS) located on the throttle body itself (ECM terminal VTA1) but rather into the accelerator pedal position sensor located on the pedal (VPA). Other than that it hooks up to RPM, ignition switch, injectors 1-4, and MAF (VG). The two other wires go to ground and activation switch.
Since the ECM uses the VTA1 data direct from the TPS to calculate everything from valve timing to long- and short-term fuel trims, I don't know what to think of that! I guess the fuel controller is altering the VPA signal sent to the TPS, and thereby manipulating the VTA1 signal then sent to the ECM?
KK, you are overthinking. Don't do it! Last night, I dreamt of fuel pumps, pressure regulators, a set of injectors. It drove me crazy.Originally Posted by kurokoma-kun ↑Well now you bastards have got me obsessing too! (not difficult) 😆
I don't know what to think of that! I guess the fuel controller is altering the VPA signal sent to the TPS, and thereby manipulating the VTA1 signal then sent to the ECM?
I am getting better at calculating the right sized pump and injectors. The biggest problem is that many of the calculations start with your desired HP output. So... I put in 400 HP. Now I have to put in a more realistic number.
So... what do you think is a realistic crank HP that a tuned Blitz kit should be able to put out?
BTW, I've been looking at this OBD II software package.
http://www.auterraweb.com/dynoscan.html
I'll also check out the ones that were posted recently.
I think its called PBSD (post boost stress disorder). I barely remember last December, when all my friends were enjoying holiday festivities while I wandered around in a daze, smelling of gas and babbling incoherently about induction system leaks 🙄
Hell if I know the max hp at the crank! 😆 why not enter a value like 150 or 175 and see what you get. Have you thought of trying to talk to someone at RC Injection btw? They are right there in Torrance, maybe you can get some inside info.
Hell if I know the max hp at the crank! 😆 why not enter a value like 150 or 175 and see what you get. Have you thought of trying to talk to someone at RC Injection btw? They are right there in Torrance, maybe you can get some inside info.
Yes. I'll give them a call. Did I say part of my dream included a fuel line popping off and spraying 91 Octane inside the car while I am full boost? I think I'll order the OBD logger by Wednesday once I research the different ones.
Weirdo! 😛Originally Posted by LtNoogie ↑Yes. I'll give them a call. Did I say part of my dream included a fuel line popping off and spraying 91 Octane inside the car while I am full boost? I think I'll order the OBD logger by Wednesday once I research the different ones.
bbwwwwaahahhahhahaa I also keep the magical tool kit and extinguisher in my car! 😁 as well as other ritual objects like the domo-kun shrine I made 🙄🆘Originally Posted by camelll ↑so I now keep all the tools and extinguisher in the trunk. 🤣
does anyone know if those flat hydraulic jacks are worth the money? they look like they should fit under lowered cars? 🤷
Q: When do I need to upgrade the injectors for my car?
A: The factory fuel injection system operates slightly rich from the factory. Because of this, certain engine upgrades such as low restriction air intake/exhaust systems and/or slight increases in boost pressure can usually be taken care of by the factory fuel injection system.
When airflow increases are substantial and the factory injectors are unable to keep up, larger injectors and/or fuel pressure increases are required. The factory fuel injection system can usually accommodate an injector that flows about 15-20% more than stock without compromising the idle quality or the low RPM drivability. If the air flow increase/horsepower target requires an injector that exceeds a 20% increase over stock, there are several options.
1. Re-program the factory ECU specifically for the new larger sized injectors.
2. Add a piggyback fuel computer that will allow you to control the larger injectors.
3. Use a stand alone engine management system to control the larger injectors.
A: The factory fuel injection system operates slightly rich from the factory. Because of this, certain engine upgrades such as low restriction air intake/exhaust systems and/or slight increases in boost pressure can usually be taken care of by the factory fuel injection system.
When airflow increases are substantial and the factory injectors are unable to keep up, larger injectors and/or fuel pressure increases are required. The factory fuel injection system can usually accommodate an injector that flows about 15-20% more than stock without compromising the idle quality or the low RPM drivability. If the air flow increase/horsepower target requires an injector that exceeds a 20% increase over stock, there are several options.
1. Re-program the factory ECU specifically for the new larger sized injectors.
2. Add a piggyback fuel computer that will allow you to control the larger injectors.
3. Use a stand alone engine management system to control the larger injectors.
Yes, I believe that I am in open loop at the time. I may have to make a run tonight just to make sure. 🙂Originally Posted by camelll ↑Noogie when you are in open loop are you still seeing the lean condition? I do not go into open loop right away it takes a little bit, even at wot but if I keep on it it goes into open loop and then I see the 11-12's on the wideband. When I am on the interstate about 80 mph and not boosting I see around stoich but as soon as I step on it and enter boost I instantly go into open loop and get good a/f readings even if I am only boosting at like 1 psi.
I can't find my wiring diagram and I can't read this image. Can you point out C20-81? I'm wired this way.Originally Posted by camelll ↑Another question I have for you is do you have a wire on your fmu going to C20-81 I was looking at 1.4 updated wiring diagram and it does not show anything going to that location and my 1.1 shows it being rpm signal.
Picture not included in this copy
Interesting. Where did it go to on the fuel controller connector?
Here's the wiring diagram that I just pulled off their website. It looks like my V1.3 wiring diagram.
Here's the wiring diagram that I just pulled off their website. It looks like my V1.3 wiring diagram.
1 attachment not included in this copy
hey guys... i just got my aem wideband installed.... im getting readings at wot 11-12
and when off at wot 12.5-13.... thinking of getting some injector off an 09 tc or corrolla... the 2az-fe engine......
and when off at wot 12.5-13.... thinking of getting some injector off an 09 tc or corrolla... the 2az-fe engine......
im jealous of your WOT readings! ahhh! I should be getting my wideband soon
Even if you did run bigger injectors ( i dont know why you would ), you wouldn't want the tc ones. Either matrix or corolla you would want..I think.Originally Posted by ae92trueno7 ↑hey guys... i just got my aem wideband installed.... im getting readings at wot 11-12
and when off at wot 12.5-13.... thinking of getting some injector off an 09 tc or corrolla... the 2az-fe engine......
Just wait, Noogie is going to be running larger injectors soon and he's going to let us know how it goes.
*My gauges came in today! YEEEE. Don't know when I'll get to install them though... 👎
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Even if you did run bigger injectors ( i dont know why you would ), you wouldn't want the tc ones. Either matrix or corolla you would want..I think.why not? they worked fine for me.
I think it was mentioned earlier in this thread or another, but it was said that the car would run worst with tc injectors. If anything, only would be good at WOT, but at idle and normal driving, TC would be too much.
If blitz doesn't offer us different fuel controllers with some success, when I get the greddy ultimate, i am going to talk to the tuner and try throw in some tc or matrix/carolla injectors with the 1zz throttle body and tune it accordingly.
If blitz doesn't offer us different fuel controllers with some success, when I get the greddy ultimate, i am going to talk to the tuner and try throw in some tc or matrix/carolla injectors with the 1zz throttle body and tune it accordingly.
Garm, what size are the tc injectors. What AFR were you reading at idle?Originally Posted by cali yaris ↑why not? they worked fine for me.
I think it was mentioned earlier in this thread or another, but it was said that the car would run worst with tc injectors."it was said" isn't the same as "it is so".
I'm not sure on the size, noogie -- throw them on and see how your car runs so we can settle this. I was normal AFR at idle, 13-14. Did fine on the dyno too, except at WOT over 5k rpm
true, this is true.Originally Posted by cali yaris ↑"it was said" isn't the same as "it is so".
tC injectors seem like a big jump to go and "try" out. Might be safer going to carolla/matrix injectors , seeing how those run, and if everything is fine, maybe move up to tCs?
Go for it noogie! haha 😉
kcalb is going boosted with blitz very very soon and i know he has a set of tc injectors. im sure if he has issues he will swap out injectors and let us know the outcome.
if the car runs ok and there is an a/f gauge to watch, trying them out should be ok if done carefully.
I don't know how much larger the tC injectors are but they aren't huge. I am pretty sure that the Greddy turbo kit for the tC comes with 330cc injectors -- so the stock ones must be smaller than that.
I don't know how much larger the tC injectors are but they aren't huge. I am pretty sure that the Greddy turbo kit for the tC comes with 330cc injectors -- so the stock ones must be smaller than that.
I'm test fitting injectors from RC Engineering into the motor on Friday. It's only a fit check to make sure everything bolts down because the injectors are physically bigger than the stock ones. If they fit, I'm working with them to decide whether to install 240cc, 270cc, or 310cc injectors.
That's why I keep asking people what size injectors they are installing and whether they are having any problems at idle or under light throttle.
That's why I keep asking people what size injectors they are installing and whether they are having any problems at idle or under light throttle.
FINALLY getting my gauges installed! 😁 Here's how they look in the mounting plate I made from some copper sheet--it took a little fitting but the lid to the compartment does close completely, and I get to keep the little rack on the left for car wash quarters! I'll be finishing the electrical wiring tomorrow (forgot I needed inline fuses 🙄).
Picture not included in this copy
Picture not included in this copy
So you plan on driving with the compartment open?
yes.... and closing it when I go to get my emissions test done 😉 just one reason for concealing the gauges. The open lid doesn't block the view in any way, and isn't all that visible from the outside eitherOriginally Posted by PETERPOOP ↑So you plan on driving with the compartment open?
nice nice. what colors do yours light up? red?
I am putting my gauges and wiring them up tomorrow too! We should have some nice pics for people tomorrow.
I am putting my gauges and wiring them up tomorrow too! We should have some nice pics for people tomorrow.
Yup red, though I kinda wish for blue now! Can't to see yours 😎
I just got a cool data logger to replace my ScanGauge. I hope to post something by tonight.
What about info on your bigger injectors experience that was suppose to happen today?
EDIT: I'm a newb. Sorry didn't see your thread on it already. Doh!
*I'll have pics of my gauges in place (not wired) up soon too!
EDIT: I'm a newb. Sorry didn't see your thread on it already. Doh!
*I'll have pics of my gauges in place (not wired) up soon too!