Replies continued
CTScottUSA, CT · Sep 26, 2012#101 Originally Posted by
Rammy ↑ Oh ok! Thanks.
And where can I tap into the parking lights? The lights that turn on when you twist the switch half way. I am also installing some LEDs for the interior and I want them to turn on w/ the parking lights. And do any of you recommend the "L bars" or just regular LED clusters? I want them to go under the whole dash kind of where your feet go.
See my remote start wiring DIY for the parking light connection:
Remote Start DIY Wiring Guide 2006-2010 Yaris CTScottUSA, CT · Oct 19, 2012#102I thought your post might have been spam with odd combination you were asking about, but since you sent me a PM with some specific questions, it seems like you are not a spammer.
In your PM you mentioned that you found all except these two:
1.Oil circuit detection
2.Cut oil and electric circuit off.
For #1, the Yaris has an oil pressure switch that is located on the front of the block about 6 inches above the oil filter. It has a single yellow wire (since its case is grounded to the block). That yellow wire is only an input to the instrument cluster for the warning light.
For #2, I am not sure what you are looking for. The only circuit associated with oil is that simple oil pressure switch.
CTScottUSA, CT · Oct 19, 2012#103OK - That makes more sense for it to be the fuel cut-off. Sometimes the directions seriously lose something in translation.
In that case, you are interested in the violet wire on Pin 7 of the smaller ECM connector.

CTScottUSA, CT · Oct 19, 2012#104I would need to see a better explanation of the module. In theory there should be two wires - in and out, so the device can interrupt the fuel pump feed.
fase4Venezuela · Mar 4, 2013#105 Originally Posted by
CTScott ↑
On the headlight stalk connector (remove the bottom steering column cover to get to it), Pin #13 is the switched wire for the taillights (which turns on with with both the high and low beams).
If the car has daytime running lights (or is 2009 or newer), then pin 13 is a ground, switched by the headlight switch (so, you would use pin 13 as your LED ground and would connect the +12 wire for the LEDs to a 12 volt source).
If the car is 2008 or older and does not have DRLs, then Pin #13 is not a switched ground, but instead is a +12V feed which is switched at Pin 10 (the wire to the left of the Pink one) (which will be green instead of white with a black strip). So, on this vintage, you would connect the + wire for the LEDs to the green wire in pin 10 and the - wire of the LEDs to a chassis ground.
hi! If I want to turn something on with the flash or high beams od the headlight, were I had to connect the + and - wires of my 12v circuit? I wanna do this because I want to open my garage goor with the opener activated when I flash my headlights.
Maybe I have to tap de + with the Pin 9 and the - at the Pin 11?
CTScottUSA, CT · Mar 4, 2013#106 Originally Posted by
fase4 ↑ hi! If I want to turn something on with the flash or high beams od the headlight, were I had to connect the + and - wires of my 12v circuit? I wanna do this because I want to open my garage goor with the opener activated when I flash my headlights.
Maybe I have to tap de + with the Pin 9 and the - at the Pin 11?
If you have a 2005, then yours is a fist gen, so the headlight wiring will be different than the second gen connector pictured.
For the first gen, the red wire with the yellow strip in pin 9 is the high beam wire from the switch. That wire gets switched to ground when the high beams are flashed, so you would use pin 9 as your switched ground wire.
You would want to use a relay that you switch the coil of with that wire, and then use the normally open relay contacts to trigger your garage door opener's switch.
fase4Venezuela · Mar 5, 2013#107regarding to colors, I cannot rely

lol 😆
Mines is a european base model so maybe for that the colors difference 🤮
Ok I get it about the pin 9. So I tap here the - right? what about the + connection? Also the relay for what would serve? 🤷
sorry for the question but I know almost nothing about this
yelcurmauritius · Dec 12, 2013#108please send full detail on toyota yaris sedan year 2008. .front totally damaged in accident .if someone selling parts let me know..! wiring system completely damaged.
bonnoranojava · Feb 28, 2014#109Hello everybody i missing a dimmer switch on my indonesian/thailand yaris 2012 5doors, i want to add tachometer on my yaris. Please help me :(
CTScottUSA, CT · Feb 28, 2014#110 Originally Posted by
bonnorano ↑ Hello everybody i missing a dimmer switch on my indonesian/thailand yaris 2012 5doors, i want to add tachometer on my yaris. Please help me :(
The Asian market Yaris do not have the dimmer rheostat. You can either just use ignition switched power for the tachometer illumination wire of you can use the illumination wire on the radio.
MittelklasseBangkok, Thailand · Mar 11, 2014#111My Thailand-spec Yaris uses electronic dimmer circuit built within the instrument cluster.
You have to toggle the trip button while having your lights on to access this function.
BADISMuscat · Jun 26, 2014#112Hi all. I'm planning to buy and mount a tachometer and water heat gauges on my Yaris 2007 Sedan. I've seen some loose wires and harnesses near the engin. These are unplugged . My yaris is number 2. It comes without RPM and Water heat Gauges. I bought it in Sultanate of Oman. My question is: does Yaris come with ready harnesses to plug and play my gauges? Otherwise, could you please show me how to mount them? What and where are the right wires located?
Thanks in advance
Sent from my iPhone using Tapatalk
THEBRADLEYontario · Oct 25, 2014#113hey man i was wondering if you could tell me how to go about installing footwell led lights to be activated with a switch prefferably in the center console by the e-brake. i know you have to bypass the firewall somehow for power, but i have no idea how/where to do so. help would be greatly appreciated.
"G"Chicago · Nov 1, 2014#114Where is the wire for the seat belt alarm?
CTScottUSA, CT · Nov 1, 2014#115 Originally Posted by
"G" ↑ Where is the wire for the seat belt alarm?
The driver's side one is under the driver's seat and then it goes under the center console directly to the SRS ECU. The passenger one is under the passenger seat and it goes to the Occupant Classification ECU and then that ECU communicates with the SRS ECU to relay the info.
What exactly are you looking to do with that wire?
wufaiToronto, Canada · Nov 1, 2014#116So does that mean if I want to steal a yaris like they do it in the movies I need to cut the yellow, pink and black wires and tap the yellow leads against the pink and black?
;)
gabbhiephilippines · Nov 18, 2014#117hi CTScott. where can i see the hotwire for parklights that is usually used in aftermarket alarms..when you press the lock/unlock button of alarm the parklight will blink once or twice.👍
CTScottUSA, CT · Nov 18, 2014#118 Originally Posted by
gabbhie ↑ hi CTScott. where can i see the hotwire for parklights that is usually used in aftermarket alarms..when you press the lock/unlock button of alarm the parklight will blink once or twice.👍
Look at my remote start wiring guide for where you can grab the parking light feed. Just verify that the wire colors match, as the Yaris in your market may be wired a bit different.
Remote Start DIY Wiring Guide 2006-2010 Yaris gabbhiephilippines · Nov 18, 2014#119oh i see, but i already tried that wire. its not the wire for the parklights.😢
i have owned my yaris since last year and until now theres no park light signal when i lock/unlock 🤷
CTScottUSA, CT · Nov 18, 2014#120 Originally Posted by
gabbhie ↑ oh i see, but i already tried that wire. its not the wire for the parklights.😢
i have owned my yaris since last year and until now theres no park light signal when i lock/unlock 🤷
Post some pictures of the connector for your headlight switch.
gabbhiephilippines · Nov 18, 2014#121ok sir i'll post pic once i got home later👍TIA
NYC-SENYC · Feb 3, 2015#122CTScott do you have a wiring diagram for the 3rd gen Yaris? In particular I'm interested in the body ECU and what wires go where.
KittPanama City, Panama · Aug 25, 2015#123Im planning to add a gauge 2 cable for my amp on my new car from the battery, however, I'm not sure where is the right place to do so. Do I have to drill the firewall?
CTScottUSA, CT · Aug 25, 2015#124 Originally Posted by
Kitt ↑ Im planning to add a gauge 2 cable for my amp on my new car from the battery, however, I'm not sure where is the right place to do so. Do I have to drill the firewall?
There is no power feed inside the cabin that you can connect that large of a wire to. You can go through the large grommet that is behind the battery, rather than drilling the firewall.
frankienapCambridge, MA · Jan 21, 2016#125Looking to add power to an aftermarket backup camera. I've searched for over 3 hours for the location of this wire. Here's a picture of the connection for the left rear light assembly on my 2008 Yaris Sedan. Anyone know which wire?
The wires going into the rear lights are: purple, green, orange, white w/a black strip and light blue.
Many many thanks!
ilikericesavannah, ga · Jan 21, 2016#126If nobody answers, you could get a test light and turn the key to accesories. With the hand brake up, you could just put it in reverse. Use a test light and back probe each wire. Record which ones have power. Then put it back into park and check again to see which one no longer has voltage. I can't look up the wire diagram right now while i am at work. CTScott would be the one to get the info to you the fastest.
frankienapCambridge, MA · Jan 21, 2016#127I think I'm going to pick up a voltage detector from Lowes tonight. One more question: will I be able to tell which wire coming from the reverse light is positive (versus negative) simply using an analog voltage detector?
CTScottUSA, CT · Jan 21, 2016#128 Originally Posted by
frankienap ↑ Looking to add power to an aftermarket backup camera. I've searched for over 3 hours for the location of this wire. Here's a picture of the connection for the left rear light assembly on my 2008 Yaris Sedan. Anyone know which wire?
The wires going into the rear lights are: purple, green, orange, white w/a black strip and light blue.
Many many thanks!
If you look at the 12 pin connector which connects to the taillight, the red in pin 5 on the right and brown in pin 5 on the left is reverse.
GagiEurope · Feb 26, 2016#129StabicraftNSW aUSTRALIA · Sep 17, 2017#130can you please tell me where to take off a 12 volt feed (when the high beam is activated) for my driving lights relay.
Little or no voltage or current required, just power ONLY when high beam is activated.
Thanking you in advance.
Mister-twisterNew York · Nov 15, 2017#131People who can share wire schematic/diagram for master windows switch. Look to hookup original master switch to aftermarket power window kit want use original switch instead of one from kit to have auto option.
2009 Yaris hatchback
Sent from my iPhone using Tapatalk
kevinj93Sydney, Australia · Nov 16, 2017#132 Originally Posted by
Stabicraft ↑ can you please tell me where to take off a 12 volt feed (when the high beam is activated) for my driving lights relay.
Little or no voltage or current required, just power ONLY when high beam is activated.
Thanking you in advance.
The headlights are earthed to turn on, with permanent 12v power. The simple way is to wire the relay coil across the 2 parallel contacts on the headlight socket.
rokusisr · Feb 6, 2021#133Hi,
I have a 2007 yaris hatchback with no daytime running lights.
I bought an aftermarket LED DRL bar, can anyone tell me how to wire it so it switches on after the car starts?
Thanks