Yarisworld Archive

Wires Inside the Yaris & What They Do

133 posts · 1,422,055 views · page 1 of 3

The ArchitectOriginal postFL · Dec 28, 2008#1
This is for the 2007 2DR Hatch Back

Wire/Function - Color - Location/Description


12 Volts - Yellow - Ignition Switch Harness

Ignition - Pink - Ignition Switch Harness

Accessory - Green - Ignition Switch Harness

Starter - Black - Ignition Switch Harness

Tach Signal - Light Green - At Diagonal Plug Under Drivers Side Dash

Lock - Brown - In Drivers Kick Panel

Unlock - Dark Green & Dark Blue - In Drivers Kick Panel

Driver Door - Red - Drivers Kick Panel In Harness to Rear
Passenger Door - Light Blue - Drivers Kick Panel In Harness to Rear
Rear Driver Door - Light Green - Drivers Kick Panel In Harness to Rear
Rear Passenger Door - Light Blue - Drivers Kick Panel In Harness to Rear

Trunk Pin - Light Blue - Drivers Kick Panel Harness to Rear

Brake Switch - Light Green - At Switch Above Brake Pedal

Park Lights - Gray - In Drivers Kick Panel
Park Lights (-) - White - At light switch harness

Hand Brake - Light Green - At DRL Module on right of steering Column

Horn - Black - In White plug on steering column

Clutch Switch - Black - At switch on clutch pedal bracket

Headlights - Light Blue - At light switch Harness

Replies 132

The ArchitectThread starterFL · Dec 28, 2008#2
These are highly necessary to know for any remote start / security alarm set-up, hope it can be of use in the future.
AlexNet0Rockland, ME · Dec 29, 2008#3
haha, nice, I installed a remote start day before yesterday and you post it yesterday, awesome info to have, if only I had waited another day!! Would have saved myself time.🙌
Over40Depok - Indonesia · Feb 9, 2009#4
Thanks man,
but it would be nicer if you could put some pics along to show where the locations are at....
anubisx99Natick, MA · Mar 8, 2009#5
speed signal cable for GPS units???
CTScottUSA, CT · Mar 8, 2009#6
Originally Posted by anubisx99 ↑
speed signal cable for GPS units???
On your 08, you can grab it at the TPWS ECU, behind the lower passenger glove box:



The ArchitectThread starterFL · Mar 8, 2009#7
I recall someone having had an issue with tapping the purple/violet wire for some other electrical project. perhaps he was just unlucky or did something wrong.

Let us know so that this thread stays accurate.
eTiMaGoBangkok, Thailand · Mar 17, 2009#8
another useful tidbit for those wishing to wire in LED mirror covers, you can get the signals from each side here. This is for the big relay/junction box in the driver's footwell area.
This way you don't have to go into your engine bay to wire them up 🙂
areithan1980North Chicago IL 60064 · Jul 11, 2009#9
how about for installing tach in the future woudl this be the same loc. to tap
toyotaOC, CA · Jul 29, 2009#10
WOW! thanks man!
yeah, pictures would be helpful.
thanks though...
yarheadL.A. County · Aug 1, 2009#11
yeah, what areithan1980 said! where would be go for a tach?
CTScottUSA, CT · Aug 1, 2009#12
Tach wire location at pin 9 of DLC3 connector:

09 (Beige wire):


07-08 (Green Wire):
Attached picture not available
47_MasoN_47Northwest Alabama · Aug 17, 2009#13
I'm looking to add a few lights under the dashboard that are on the same circuit as the dome light (so they turn on when the door opens) and was wondering which wires they are. I have the 09 sedan, does anyone know which wires I could use?
CTScottUSA, CT · Aug 17, 2009#14
Originally Posted by 47_MasoN_47 ↑
I'm looking to add a few lights under the dashboard that are on the same circuit as the dome light (so they turn on when the door opens) and was wondering which wires they are. I have the 09 sedan, does anyone know which wires I could use?
4K.jpg

The connector (4K) on the upper left in this picture, is the feed to the map and dome lights. White with a black stripe ground, Pink is the "door open" switched ground, and blue is 12V fed from the DOME fuse.
47_MasoN_47Northwest Alabama · Aug 18, 2009#15
Alright, so if I'm thinking correctly I should connect the + lead from the lights to the blue wire, and the ground to the pink one?
CTScottUSA, CT · Aug 18, 2009#16
Originally Posted by 47_MasoN_47 ↑
Alright, so if I'm thinking correctly I should connect the + lead from the lights to the blue wire, and the ground to the pink one?
Correct.
47_MasoN_47Northwest Alabama · Aug 18, 2009#17
Awesome, thanks!
Liu997Hicksville, LI · Aug 21, 2009#18
So the yellow 12volt wire described in the first post is constant even when the car is off?
CTScottUSA, CT · Aug 21, 2009#19
Yes
kompressorgplPortugal · Sep 19, 2009#20
Hello! I have an alarm to put on my Yaris (from 2002). Where i can find a diagram of the car with that?
AlexNet0Rockland, ME · Sep 19, 2009#21
use a multimeter and probe the wires, and make your own diagram, thats what I did when I installed my remote starter.
charleschia1986Perth, WA · Oct 20, 2009#22
Originally Posted by CTScott ↑
Attached picture not available

The connector (4K) on the upper left in this picture, is the feed to the map and dome lights. White with a black stripe ground, Pink is the "door open" switched ground, and blue is 12V fed from the DOME fuse.

hi there,
may i know where can i find this stuff?

regards,
Charles
CTScottUSA, CT · Oct 20, 2009#23
Originally Posted by charleschia1986 ↑
hi there,
may i know where can i find this stuff?

regards,
Charles
If you mean where are the wires in the picture, they are right behind the pull out pocket on the bottom left of the dash.
charleschia1986Perth, WA · Oct 20, 2009#24
Originally Posted by CTScott ↑
If you mean where are the wires in the picture, they are right behind the pull out pocket on the bottom left of the dash.
hi there,
so did ya mean it is located under the driver seat or passenger seat? because my driver seat is on right hand side.
regards,
Charles.
CTScottUSA, CT · Oct 20, 2009#25
Originally Posted by charleschia1986 ↑
hi there,
so did ya mean it is located under the driver seat or passenger seat? because my driver seat is on right hand side.
regards,
Charles.
In that case it's behind the passenger lower glove box.
Sora65Brampton · Oct 22, 2009#26
Originally Posted by CTScott ↑
Correct.
Wait so i can put for than 1 wire in that hole?
Or should i use on of those clip things to wire?

i have no idea about wiring stuff :(
but i really wanna get some lights for the foot area..
CTScottUSA, CT · Oct 22, 2009#27
Originally Posted by Sora65 ↑
Wait so i can put for than 1 wire in that hole?
Or should i use on of those clip things to wire?

i have no idea about wiring stuff :(
but i really wanna get some lights for the foot area..
Use the clip things (tap splices). Just sticking the wire in along side of the existing wire does not make a reliable connection.
Sora65Brampton · Oct 23, 2009#28
But where im getting at is right?
i could put the wire i need powered in the same hole as the blue one where theres 12v?
CTScottUSA, CT · Oct 23, 2009#29
Originally Posted by Sora65 ↑
But where im getting at is right?
i could put the wire i need powered in the same hole as the blue one where theres 12v?
Yes. That blue +12 is always on though. The pink is switched ground for the inside lights.
yoxxsilver spring, md · Nov 12, 2009#30
How to plug in a water temp gauge?
All I really need is the signal for the temp

wich one is it, please HELP
CTScottUSA, CT · Nov 12, 2009#31
Originally Posted by yoxx ↑
How to plug in a water temp gauge?
All I really need is the signal for the temp

wich one is it, please HELP
There's a 2 pin connector to the engine coolant temp sensor. It has a pink and a blue wire that go to pins 96 (pink) and 97 (blue) on connector C20 of the ECM.

Conn C20.jpg
yoxxsilver spring, md · Nov 13, 2009#32
Where r this locate it, for some reason I can't find this box you r showing me, been looking under the hood for an hour and I can't find it
aucoriumSouth Africa · Nov 13, 2009#33
and the speed sensor wire ?
CTScottUSA, CT · Nov 13, 2009#34
Originally Posted by yoxx ↑
Where r this locate it, for some reason I can't find this box you r showing me, been looking under the hood for an hour and I can't find it
With the hood open it is to your left (the car's right) against the firewall. It is the big silver box with the two large connectors.
CTScottUSA, CT · Nov 13, 2009#35
Originally Posted by aucorium ↑
and the speed sensor wire ?
The easiest place to tap it is at the speedometer. It is the pink wire in pin 17 of connector D1, which is the larger of the two connectors.

Conn D1 - Combination Meter.jpg
yoxxsilver spring, md · Nov 13, 2009#36
Originally Posted by CTScott ↑
There's a 2 pin connector to the engine coolant temp sensor. It has a pink and a blue wire that go to pins 96 (pink) and 97 (blue) on connector C20 of the ECM.

Attachment 30002
hey ctscott

i got a little problem
the water temp that i got, only have one wire for the water temp? wich one should i use for this? the pin 96 (pink wire) or pin 97 (blue wire)
CTScottUSA, CT · Nov 13, 2009#37
Originally Posted by yoxx ↑
hey ctscott

i got a little problem
the water temp that i got, only have one wire for the water temp? wich one should i use for this? the pin 96 (pink wire) or pin 97 (blue wire)
What temp gauge did you buy?
aucoriumSouth Africa · Nov 13, 2009#38
Originally Posted by CTScott ↑
The easiest place to tap it is at the speedometer. It is the pink wire in pin 17 of connector D1, which is the larger of the two connectors.

Attachment 30013

where is that connector buddy ?

i wanna hook it up to my apexi rsm speed wire
CTScottUSA, CT · Nov 13, 2009#39
Originally Posted by aucorium ↑
where is that connector buddy ?

i wanna hook it up to my apexi rsm speed wire
Pop the trim from around the speedometer and you'll see two connectors going to the cluster assembly. If your car is left hand drive the connector you want will be on right and if it's right hand drive it will be on the left.
aucoriumSouth Africa · Nov 13, 2009#40
or should i say where in the car do i find that connector?
aucoriumSouth Africa · Nov 13, 2009#41
Originally Posted by CTScott ↑
Pop the trim from around the speedometer and you'll see two connectors going to the cluster assembly. If your car is left hand drive the connector you want will be on right and if it's right hand drive it will be on the left.
aaah ok ! thx bro !! no other locations for that wire ? like on the ODB2 port? how does the scangauge get speedo signal? cant i somehow hook into that?
CTScottUSA, CT · Nov 13, 2009#42
Originally Posted by aucorium ↑
aaah ok ! thx bro !! no other locations for that wire ? like on the ODB2 port? how does the scangauge get speedo signal? cant i somehow hook into that?
The ScanGauge gets it via CAN Bus data at the OBD port. If your car has TPMS the speed signal is available there as well. honestly, popping the trim from around the cluster takes no tools and just a couple of seconds.
aucoriumSouth Africa · Nov 13, 2009#43
Originally Posted by CTScott ↑
The ScanGauge gets it via CAN Bus data at the OBD port. If your car has TPMS the speed signal is available there as well. honestly, popping the trim from around the cluster takes no tools and just a couple of seconds.

im a little scared to mess up the plastics as i have a heavy had. how does that plastics come off anyway?
CTScottUSA, CT · Nov 13, 2009#44
Originally Posted by aucorium ↑
im a little scared to mess up the plastics as i have a heavy had. how does that plastics come off anyway?
Pull off the two vertical black pieces that surround the radio.

Pull the cluster trim gently at the top, where the seam is to loosen it.

Pull the cluster trim along the bottom straight back towards you to free the tabs that go into the top of the radio trim.
CTScottUSA, CT · Nov 13, 2009#46
Originally Posted by yoxx ↑
This is the one I got
http://www.harborfreight.com/cpi/cta...unction=Search

it match my tach and voltmeter
That link is not working. Is it their Nitrous brand one?

Also, does it not include a temp sensor of its own? I can't see how a gauage manufacturer would be able to assume that car manufacturers use the same spec temp sensors.
yoxxsilver spring, md · Nov 13, 2009#47
Originally Posted by CTScott ↑
That link is not working. Is it their Nitrous brand one?

Also, does it not include a temp sensor of its own? I can't see how a gauage manufacturer would be able to assume that car manufacturers use the same spec temp sensors.
yes is their nitrous brand, and yes it come with a sensor but i dont want to drill a hole on my car for the sensor, but if i can get around it and NOT drill a hole on my car will be better

now for the sensor it only have one cable and you give me two, so i didnt know on wich one to plug it in so i havent test it on any of them yet

now i gues that you r familiar with the gauge that i got, is there a extra hole on the car that i can put the sensor that came with it???


i really want this to work men, thanks for your time
CTScottUSA, CT · Nov 13, 2009#48
Originally Posted by yoxx ↑
yes is their nitrous brand, and yes it come with a sensor but i dont want to drill a hole on my car for the sensor, but if i can get around it and NOT drill a hole on my car will be better

now for the sensor it only have one cable and you give me two, so i didnt know on wich one to plug it in so i havent test it on any of them yet

now i gues that you r familiar with the gauge that i got, is there a extra hole on the car that i can put the sensor that came with it???


i really want this to work men, thanks for your time


That makes more sense. The more I thought about it, I realized that water temp gauges aren't like tachs, where you can tie them to a standardized signal.

As for where to add your gauges sensor, there really isn't an existing extra hole that I am aware of. I believe that there are plates that can be installed under the thermostat housing that give you a place to install the sensor. I've seen people install them in other cars by drilling and tapping.

I know that others on here have installed them, So, you might want to start a new thread asking where and how people installed their sensors.
yoxxsilver spring, md · Nov 13, 2009#49
Originally Posted by CTScott ↑
That makes more sense. The more I thought about it, I realized that water temp gauges aren't like tachs, where you can tie them to a standardized signal.

As for where to add your gauges sensor, there really isn't an existing extra hole that I am aware of. I believe that there are plates that can be installed under the thermostat housing that give you a place to install the sensor. I've seen people install them in other cars by drilling and tapping.

I know that others on here have installed them, So, you might want to start a new thread asking where and how people installed their sensors.
that makes sense, ill start a new thread

now let me ask you a question, do you think that if i use one of the line that you told me from the pin 96 (pink) or pin 97 (blue) i think i could try that and see, because i reeeeeeally don't want to drill a hole on my car, and now that i think there must be a line that i can tap into because, on the speedometer there is two light for temp, one light up COOL so when you start the car and the other is the red light that have the signal of hot temp, anyway let me know what you think

thank again for the time
CTScottUSA, CT · Nov 13, 2009#50
Originally Posted by yoxx ↑
that makes sense, ill start a new thread

now let me ask you a question, do you think that if i use one of the line that you told me from the pin 96 (pink) or pin 97 (blue) i think i could try that and see, because i reeeeeeally don't want to drill a hole on my car, and now that i think there must be a line that i can tap into because, on the speedometer there is two light for temp, one light up COOL so when you start the car and the other is the red light that have the signal of hot temp, anyway let me know what you think

thank again for the time
I don't believe that it would work. The single wire sensor is a one wire thermocouple. A two wire device, like what is on the car, is a thermistor. A thermocouple generates voltage relative to change in temperature. A thermistor changes resistance based on temperature. So, the output of the two sensor types is completely different.

As for the lights, they are illuminated by the cluster's microcontroller, based on data from the ECM (who processes the sensor data).