Replies continued
yoxxsilver spring, md · Nov 13, 2009#51 Originally Posted by
CTScott ↑ I don't believe that it would work. The single wire sensor is a one wire thermocouple. A two wire device, like what is on the car, is a thermistor. A thermocouple generates voltage relative to change in temperature. A thermistor changes resistance based on temperature. So, the output of the two sensor types is completely different.
As for the lights, they are illuminated by the cluster's microcontroller, based on data from the ECM (who processes the sensor data).
men that socks, cus i really want it to put this water temp gauge on cus it match my tach and my voltmeter, i guess am gonna have to get some sort of adapter so i can get the sensor in
thank buddy
fsj2Maumelle, AR · Nov 18, 2009#52I want to wire up some aftermarket LED driving lights. I want them to come when the car is in drive. Is there a easy place to connect them? 2010 5 dr HB. Thanks.
CTScottUSA, CT · Nov 18, 2009#53 Originally Posted by
fsj2 ↑ I want to wire up some aftermarket LED driving lights. I want them to come when the car is in drive. Is there a easy place to connect them? 2010 5 dr HB. Thanks.
To have them come on when the car is "In drive" with an automatic transmission, you could tap the connector C27 on the transmission. The 10A Gauge circuit feeds through the Park/Neutral/Position Switch on the A/T to feed the indicator on the cluster and the ECM with the position of the A/T shift. For low power lights (LED lights under 1A) you could feed them directly. For high power lights (incandescents or HIDs) you would have the Drive indicator feed the coil of a relay, which would then have it's own power feed for the lights.
C27 is the 9 pin connector on the front of the transmission (by the shift linkage). It has a row of 4 and a row of 5 pins. The center wire (light blue) on the 5 pin row is the "Drive" indicator wire. It will have 12V on it when the shift is in drive. For ground, you can grab a chassis ground, like the ground bolt under the left headlight.
charleschia1986Perth, WA · Nov 24, 2009#54 Originally Posted by
CTScott ↑ Attached picture not available
The connector (4K) on the upper left in this picture, is the feed to the map and dome lights. White with a black stripe ground, Pink is the "door open" switched ground, and blue is 12V fed from the DOME fuse.
Hihi, I already tested the wires tat u mentioned in the picture.. The blue wire does give constant 12v and the pink wire should turn on the lights with the door right?
I already tested the pink wire by multimeter and it will only give 12v when the door is closed.
So may I know what can I do in order to get 12v out when the door is open because I want my led to be on only when the door is open...
Thanks...
CTScottUSA, CT · Nov 24, 2009#55 Originally Posted by
charleschia1986 ↑ Hihi, I already tested the wires tat u mentioned in the picture.. The blue wire does give constant 12v and the pink wire should turn on the lights with the door right?
I already tested the pink wire by multimeter and it will only give 12v when the door is closed.
So may I know what can I do in order to get 12v out when the door is open because I want my led to be on only when the door is open...
Thanks...
Use the pink as ground and the blue as your +12V.
charleschia1986Perth, WA · Nov 24, 2009#56thanks a lot...
i tried and it WORKS.....
thank scott
zuberioMississauga, ON · Dec 5, 2009#57 Originally Posted by
eTiMaGo ↑ another useful tidbit for those wishing to wire in LED mirror covers, you can get the signals from each side here. This is for the big relay/junction box in the driver's footwell area.
This way you don't have to go into your engine bay to wire them up 🙂
Thankyou ThankYou THANKYOU!!!🙇
charleschia1986Perth, WA · Dec 6, 2009#58yarisugiハワイ · Dec 22, 2009#59Hi all. Is there a place I can tap into the engine bay for turn signals besides the wires that lead to the signal lamps?
CTScottUSA, CT · Dec 22, 2009#60 Originally Posted by
yarisugi ↑ Hi all. Is there a place I can tap into the engine bay for turn signals besides the wires that lead to the signal lamps?
You can tap into the turn signal wires in the under hood fuse panel. On connector B13 (left connector in this picture), the light green and dark green wires in the upper row (next to the two red wires for my fog lights) are the turn signals. Light green is left, dark green is right.

yarisugiハワイ · Jan 21, 2010#61One more question, where can I tap in for the parking lights - the lights that go on just before I turn on the headlights?
CTScottUSA, CT · Jan 21, 2010#62 Originally Posted by
yarisugi ↑ One more question, where can I tap in for the parking lights - the lights that go on just before I turn on the headlights?
The White wire next to the blue and orange on the headlight stalk connector. You ground the wire to make the lights come on.
yarisugiハワイ · Jan 22, 2010#63Sorry, should've made my question a bit clearer. I'm looking to see if there is one in the fuse box like the one pictured above.
CTScottUSA, CT · Jan 22, 2010#64 Originally Posted by
yarisugi ↑ Sorry, should've made my question a bit clearer. I'm looking to see if there is one in the fuse box like the one pictured above.
In the fuse panel, it is pin 3 on Connector B13, which is the green wire next to the two red wires in my picture above. If you don't have fogs installed, the place where the two reds are in my picture will be empty on yours.
jonimacKSA · Jun 9, 2010#65 Originally Posted by
CTScott ↑ Attached picture not available
The connector (4K) on the upper left in this picture, is the feed to the map and dome lights. White with a black stripe ground, Pink is the "door open" switched ground, and blue is 12V fed from the DOME fuse.
Hi to all... just a noob here in M.E., just wondering if I tap the leads (+,-) of an LED light to the pink n blue from that pic above, will the new led light acts the same as the dome light? will the new led light dim to off as well upon turning off the ignition? Or just turns on when the doors were open? Sorry to much question. Need help where I can tap my led lights so that it behaves the same like the dome light, using its switch also to turn on my led lights underneath. Thanks so much. -jon🙂
CTScottUSA, CT · Jun 9, 2010#66 Originally Posted by
jonimac ↑ Hi to all... just a noob here in M.E., just wondering if I tap the leads (+,-) of an LED light to the pink n blue from that pic above, will the new led light acts the same as the dome light? will the new led light dim to off as well upon turning off the ignition? Or just turns on when the doors were open? Sorry to much question. Need help where I can tap my led lights so that it behaves the same like the dome light, using its switch also to turn on my led lights underneath. Thanks so much. -jon🙂
If you tap the pink and blue, the LEDs will behave the same as them dome lights, provided that you leave the dome light switch in the "Door" position. If you manually switch the dome to "On", with the doors closed, the LEDs won't light up with the dome.
jonimacKSA · Jun 9, 2010#67 Originally Posted by
CTScott ↑ If you tap the pink and blue, the LEDs will behave the same as them dome lights, provided that you leave the dome light switch in the "Door" position. If you manually switch the dome to "On", with the doors closed, the LEDs won't light up with the dome.
Thanks CTScott... got the idea!😉
CTScottUSA, CT · Sep 21, 2010#68 Originally Posted by geniusmiki ↑
The black one is for the Door lock receiver. Does your Yaris have a manual or automatic transmission. If it's a manual, then the other two are for the A/T shift illumination and for the shift lock control ECU.
sleey0PA · Sep 22, 2010#69I just want to take a minute to say a big, fat THANK YOU to ctscott for his help on these boards.
I have used a lot of your info and I believe you deserve at least this much appreciation!
Thanks, brother!
nmd55Tampa, FL · Oct 21, 2010#70it tried tapping the light blue wire at the headlight switch, but now my headlight wont turn off and the lights on my power window switches are on all the time?
did i just do a bad job tapping this? or can i not tap the light blue wire for my power window switches?
thanks,
nick
CTScottUSA, CT · Oct 21, 2010#71 Originally Posted by
nmd55 ↑ it tried tapping the light blue wire at the headlight switch, but now my headlight wont turn off and the lights on my power window switches are on all the time?
Tried tapping that wire for what purpose?
nmd55Tampa, FL · Oct 22, 2010#72the power window switches i got light up at night when the headlights are on
CTScottUSA, CT · Oct 22, 2010#73 Originally Posted by
nmd55 ↑ the power window switches i got light up at night when the headlights are on
OK. First off there are two blue wires on the headlight stalk. The "light blue" is the darker of the two. The other color is called "sky blue".
Secondly, you don't want to use a high current circuit, like the headlight switch, to drive interior lighting. You want to use the illumination circuit, which you can access either at the shift lever or at the dimmer rheostat.
At the shift lever, there is a two pin connector with a white and a green wire. Green is +12, white is ground.
At the dimmer rheostat, there is a 10 pin connector. The sky blue wire is +12 and the light green is the headlight switched ground.
nmd55Tampa, FL · Oct 26, 2010#74^^ awesome thanks so much for the info!!!
nmd55Tampa, FL · Oct 26, 2010#75So i tried the sky-blue wire at the dimmer and it works. However its dimming the power window switches in the opposite direction as the dash. So when the dash is fully lit, the power window switches are not lit at all and vice-versa.
I checked the connection with my multi-meter and it is indeed +12V so im not sure whats wrong.
My car is MT so there is no shift lever, is there another headlight source i can tap?
Thanks for the help!
CTScottUSA, CT · Oct 26, 2010#76 Originally Posted by
nmd55 ↑ So i tried the sky-blue wire at the dimmer and it works. However its dimming the power window switches in the opposite direction at the dash. So when the dash is fully lit, the power window switches are not lit at all and vice-versa.
I checked the connection with my multi-meter and it is indeed +12V so im not sure whats wrong.
Thanks for the help!
That's correct. Is the light wiring on your switch separate from the switch controls, or is it integrated, where it shares the same ground? It sounds like the latter, as the dimmer brings the ground up, rather than the +12 down to do the dimming. If that's the case, using green as your + and chassis ground as your ground should correct the reversed behavior.
nmd55Tampa, FL · Oct 26, 2010#77as it turns out i was tapping the LG wire the whole time thats why it was dimming in the opposite direction. However the SB wire is an ignition switched 12V, so tapping that doesnt work either because the switches are on all the time with the SB wire.
I think i am going to have to find another source to tap.
CTScottUSA, CT · Oct 27, 2010#78 Originally Posted by
nmd55 ↑ as it turns out i was tapping the LG wire the whole time thats why it was dimming in the opposite direction. However the SB wire is an ignition switched 12V, so tapping that doesnt work either because the switches are on all the time with the SB wire.
I think i am going to have to find another source to tap.
I just realized that I gave you the wrong wire for the +. Use the brown on the dimmer rheostat, not the blue.
iicaieMalaysia · Mar 19, 2011#79 Originally Posted by
CTScott ↑ If you tap the pink and blue, the LEDs will behave the same as them dome lights, provided that you leave the dome light switch in the "Door" position. If you manually switch the dome to "On", with the doors closed, the LEDs won't light up with the dome.
Hi, how do you suggest wiring LEDs so that they behave exactly like the dome light does? ie. turn on when doors open, switch to ON - light up with dome light. thanks
CTScottUSA, CT · Mar 19, 2011#80 Originally Posted by
iicaie ↑ Hi, how do you suggest wiring LEDs so that they behave exactly like the dome light does? ie. turn on when doors open, switch to ON - light up with dome light. thanks
The only way to make them function exactly the same as the dome, including the switched on mode is to run the power wire up through the headliner to the dome light and make your connection there.
iicaieMalaysia · Mar 23, 2011#81 Originally Posted by
CTScott ↑ The only way to make them function exactly the same as the dome, including the switched on mode is to run the power wire up through the headliner to the dome light and make your connection there.
Thanks! I just tapped power for my 12V footwell LEDs from the 4K connector, pink/blue wires. However, I used some old wires from my old computer (more or less same thickness/gauge as the pink/blue ones, quite thin). I think they're around 22-26AWG, same as the original pink/blue wires, however the pink/blue wires may be solid copper core, while the wires I'm using are stranded aluminum.
Now I'm worried they might catch fire/melt/burn. What's your opinion on this? Should I get thicker gauge wires and redo the whole thing?
CTScottUSA, CT · Mar 23, 2011#82 Originally Posted by
iicaie ↑ Thanks! I just tapped power for my 12V footwell LEDs from the 4K connector, pink/blue wires. However, I used some old wires from my old computer (more or less same thickness/gauge as the pink/blue ones, quite thin). I think they're around 22-26AWG, same as the original pink/blue wires, however the pink/blue wires may be solid copper core, while the wires I'm using are stranded aluminum.
Now I'm worried they might catch fire/melt/burn. What's your opinion on this? Should I get thicker gauge wires and redo the whole thing?
That feed is fused by the DOME fuse. As long as your wires are sized appropriately for that FUSE you will be fine.
iicaieMalaysia · Mar 23, 2011#83 Originally Posted by
CTScott ↑ That feed is fused by the DOME fuse. As long as your wires are sized appropriately for that FUSE you will be fine.
This is what i'm trying to figure out, Scott. Cos the wires i used were pretty thin, 26AWG. I dont know the gauge of the original pink/blue wires coming out of the 4K connector to the dome light,
but they look pretty much the same.
CTScottUSA, CT · Mar 23, 2011#84 Originally Posted by
iicaie ↑ This is what i'm trying to figure out, Scott. Cos the wires i used were pretty thin, 26AWG. I dont know the gauge of the original pink/blue wires coming out of the 4K connector to the dome light,
but they look pretty much the same.
Those wires are actually 20AWG. Your 26AWG is only rated for 2.2 Amps, so to be safe you should add a 2A inline fuse between it and your new lighting.
MudBugAZ, USA · Apr 23, 2011#85I put an aftermarket stereo in my 07 hatch but I couldn't find the dimmer wire.
The stereo has this feature.
This blue light is almost blinding at night.
Is there a dimmer wire in the stereo bundle?
mackyitaly · May 15, 2011#86any one who knows where can i find main body ECU of yaris 2006 because ihave bypass module dball data base tranponder i need to connnect (stsw output to stsw+ pi4 of ECU main body , but idont no where? pls help any diagram regarding stsw wire yelow no 8 frm. dball
http://www.xpresskit.com/VehicleComp...px?p=null&year to see chart of my problem,
CTScottUSA, CT · May 15, 2011#87The main body ECU is actually the white box under the dash with the fuse panel mounted to the bottom of it.
mackyitaly · May 15, 2011#88thnks i check it up later
IsLNdbOiLas Vegas, NV · Jul 6, 2011#89 Originally Posted by
CTScott ↑ On your 08, you can grab it at the TPWS ECU, behind the lower passenger glove box:

Anyone know which of those wires is switched / ignition power? I tried the other red one, (the red one that's not labeled), but it's not working.
CTScottUSA, CT · Jul 6, 2011#90The red one that's hidden on the end of the second row is definitely ignition switched +12 volts. Make sure you have a good ground that you are referencing it to, or use the white wire with the black stripe on that connector as your ground.
CTScottUSA, CT · Sep 6, 2011#91 Originally Posted by cgarcia1821 ↑
i want to install led lights in the interior, but i want them to turn on when i turn on the headlights...any help with where i can locate the correct wires for this? a picture would help :)
On the headlight stalk connector (remove the bottom steering column cover to get to it), Pin #13 is the switched wire for the taillights (which turns on with with both the high and low beams).
If the car has daytime running lights (or is 2009 or newer), then pin 13 is a ground, switched by the headlight switch (so, you would use pin 13 as your LED ground and would connect the +12 wire for the LEDs to a 12 volt source).
If the car is 2008 or older and does not have DRLs, then Pin #13 is not a switched ground, but instead is a +12V feed which is switched at Pin 10 (the wire to the left of the Pink one) (which will be green instead of white with a black strip). So, on this vintage, you would connect the + wire for the LEDs to the green wire in pin 10 and the - wire of the LEDs to a chassis ground.
CTScottUSA, CT · Sep 7, 2011#92 Originally Posted by cgarcia1821 ↑
I accidentally starting messing with these wireds to see if any were for the headlights (i was trying to install interior led lights) and all of my dashboard lights are now going off like crazy (airbag, check engine, battery, sliding, etc), the a/c and heater doesn't work, the turns signals don't work if i step on the brake, and it no longer indicates what gear i'm in. I really messed up, but I would like to know if anyone has had this issue or knows a solution or what's going on. 🙁
YIKES!!!!
Check the Dome and ETCS fuses in the under hood fuse panel. Hopefully you popped one of those and didn't cook the ECM. The DLC3 connector is purely for diagnostics. There is a constant power wire on the connector for powering a diagnostic tool, but other than that no pin on that connector should ever be connected to a load.
Rudra223Guyana · Jul 16, 2012#93where is the reverse light wire?
and what is the colour?
mpyoosSouth Africa Cape Town · Aug 17, 2012#94Hi,
Trying to wire an aftermarket radio
Please advise:
Re- yellow wire, a black wire, a pink wire and a white wire - which wire is ground (earth) and which wire is power - 12v? Which fuse is the radio fuse? The radio works if I connect directly to the battery...
CTScottUSA, CT · Aug 17, 2012#95 Originally Posted by
mpyoos ↑ Hi,
Trying to wire an aftermarket radio
Please advise:
Re- yellow wire, a black wire, a pink wire and a white wire - which wire is ground (earth) and which wire is power - 12v? Which fuse is the radio fuse? The radio works if I connect directly to the battery...
What year is your Yaris and was it built in Japan or France?
mamun22sBangladesh · Aug 28, 2012#96 Originally Posted by
CTScott ↑ Tach wire location at pin 9 of DLC3 connector:
09 (Beige wire):
07-08 (Green Wire):
Attached picture not available
Can any one help the abt the chip on the pic coloured red and blue. what is there function?Be cause one of them getting hot. What actually they do? and also the function of the fuse? How do i know whether they functioning or not.
CTScottUSA, CT · Aug 28, 2012#97 Originally Posted by
mamun22s ↑ Can any one help the abt the chip on the pic coloured red and blue. what is there function?Be cause one of them getting hot. What actually they do? and also the function of the fuse? How do i know whether they functioning or not.
They are relays. The left one is the IG1 relay and the right one is the HTR relay. The left one gets warm when the ignition is on and the right gets warm when the blower is running. That is normal.
The fuse above it to the left is for the power windows and the one above it to the right is for the defogger.
RammyHesperia · Sep 26, 2012#98Where is this whole piece as seen in post 14?
I want to wire some door sills and have them light up when the door opens up. I usually keep the light in the off position and not on the "door" position. So if I want it to work the way I want it to, am I going to have to keep the switch on "door"? This might be the wrong thread but I was redirected by Scott on another thread. Thanks!
CTScottUSA, CT · Sep 26, 2012#99 Originally Posted by
Rammy ↑ Where is this whole piece as seen in post 14?
I want to wire some door sills and have them light up when the door opens up. I usually keep the light in the off position and not on the "door" position. So if I want it to work the way I want it to, am I going to have to keep the switch on "door"? This might be the wrong thread but I was redirected by Scott on another thread. Thanks!
Behind the little storage cup on the bottom left side of the dash.
RammyHesperia · Sep 26, 2012#100Oh ok! Thanks.
And where can I tap into the parking lights? The lights that turn on when you twist the switch half way. I am also installing some LEDs for the interior and I want them to turn on w/ the parking lights. And do any of you recommend the "L bars" or just regular LED clusters? I want them to go under the whole dash kind of where your feet go.