Yarisworld Archive

DC Sports Header install and evaluation

202 posts · 149,038 views · page 3 of 5

Replies continued

HerbicidalRoseville, CA - USA. · Aug 29, 2009#101
Originally Posted by Galavoxx ↑
Sorry for the delay. Yes, I re-used all bolts including the spring loaded collector bolt. They were all in excellent condition, even after $35K miles.

One thing I didn't mention in my original post, I don't know if this is just my car but there is a threaded tab on the side of the header (new and old) that wasn't connected to anything and doesn't appear that it could be. Is this supposed to connect to the "support bracket" you are talking about? If so, my car didn't come with a support bracket.
As I think mentioned before I'm a little disappointed that I could not reuse the spring loaded bolts as the thread pitch is wrong. I'm glad to hear the DC's were a match. I also bought longer bolts for the header that hold it to the engine block, I just didn't like how little thread there was left due to the thicker flange and thicker gasket.

Yeah, the support bracket is basically in the shape of a triangle, two bolts to the engine block and one to the threaded tab. I wonder why yours didn't have one? Sedan vs hatchback? 🤷

Oh, I now have a new air/fuel sensor, just haven't installed it yet. Probably tomorrow, then I can start driving my Yaris back to work and get a feel for the new header.
KlintonOKC · Aug 30, 2009#102
im going to pick up that header soon im pretty happy with what i have seen on it
YodaFL · Aug 30, 2009#103
i have the dc header. had it for awhile it is wonderful. you do lose some down end tho🙁 but it will make the acceleration feel alot smother. gives a small boost in hp too. Check the sticky mines is up there along with others. install was pretty straight forward too.
rac23Long Island New York · Sep 2, 2009#104
I ordered my DC header from Garm this week. It should be in Friday. Can anyone tell me where I can get the exhaust pipe gasket for it? I don't want to buy it from Toyota. I think they want $50 for it.
HerbicidalRoseville, CA - USA. · Sep 2, 2009#105
Originally Posted by rac23 ↑
I ordered my DC header from Garm this week. It should be in Friday. Can anyone tell me where I can get the exhaust pipe gasket for it? I don't want to buy it from Toyota. I think they want $50 for it.
I'll sell you mine for $30. My Megan header came with a new gasket. My car has about 12,500 miles on it. 🙂
kngrsllSpartanburg, SC · Sep 2, 2009#106
Originally Posted by rac23 ↑
I ordered my DC header from Garm this week. It should be in Friday. Can anyone tell me where I can get the exhaust pipe gasket for it? I don't want to buy it from Toyota. I think they want $50 for it.
i reused my stock one and it works fine.
rac23Long Island New York · Sep 2, 2009#107
I guess I'll try to salvage mine first. I was hoping someone would make an alternative product at a more reasonable price. That gasket shouldn't cost more than $10.
If you bought a Yaris part by part from Toyota's parts department and then put it together yourself, it would probably cost you more than buying a new Porsche.
aucoriumSouth Africa · Sep 8, 2009#108
well this is definitly a very informative thread ... i have been reading most of the threads of all the headers available for the yaris , from the megan headers with the install issues of not being able to use the spring bolts , to weapon R headers , and it seems as if the DC sports header is the only one without any install issues. I was thinking of saving some bucks and rather getting a cheaper header like megan , weapon R , thunder etc , but i recon i'll save a little longer and get the DC sports , no mess , no fuss , can reuse every OEM part.

thanks for the info guys :-)

PS: going to do a custom complete local exhaust and doing a de-cat , so by the time i get the header its going to make a noticable difference.
bronzebullet232California · Sep 17, 2009#109
Do you have an aftermarket mid-pipe? I'm planning on doing DC headers for sure along with afe intake, and nst cr-lite pulley.
hatchbackkid82. · Sep 18, 2009#110
I have the afe intake, Nst pulley kit, DC header that i installed on Monday, nitto mid pipe, thunder axle back. It's an awesome combo of parts👍 The header does lose some low end but makes up for it, car has more punch in the mid and top end, ass dyno can feel the difference.

Originally Posted by bronzebullet232 ↑
Do you have an aftermarket mid-pipe? I'm planning on doing DC headers for sure along with afe intake, and nst cr-lite pulley.
kngrsllSpartanburg, SC · Sep 18, 2009#111
Originally Posted by hatchbackkid82 ↑
I have the afe intake, Nst pulley kit, DC header that i installed on Monday, nitto mid pipe, thunder axle back. It's an awesome combo of parts👍 The header does lose some low end but makes up for it, car has more punch in the mid and top end, ass dyno can feel the difference.
did you notice a difference with the mid pipe and exhaust? i didnt do those, i think the header had the best gains, and i dont want the noise/attention of an an exhaust.
fmicleSan Jose, CA, USA · Sep 20, 2009#112
After a few hours in the trenches, I finally finished installing my DC header. I had some issue loosening the O2 sensor, but I got it off eventually, with a 4 ft pipe as a wrench extension... The thread was ruined about 60-70%, but I managed to mount it on the new header just fine, so I'm not going to get a new one for now.

Unfortunately, I couldn't fit the header onto the engine bracket with the stock bolt (as it's supposed to be) no matter what I tried - like loosening all bolts and trying the header tab bolt 1st.

I eventually improvised a thinner bolt and nut to fasten them together. I hope it holds. No problems with the donut (it came of easily) and the spring bolts worked fine as well.

I was also not able to get my torque wrench in there for the world... so I hand tightened all the bolts... Any thoughts/concerns on that?

Did anyone else experience similar fitment problems?
cali yarisCanoga Park, CA · Sep 20, 2009#113
What is the recommended torque? You can hand tighten if you know the feel of a torque range.
fmicleSan Jose, CA, USA · Sep 20, 2009#114
Originally Posted by cali yaris ↑
What is the recommended torque? You can hand tighten if you know the feel of a torque range.
It's 25 lb-ft. I don't know the feel of a torque range, I only know how it felt to loosen it, even though I don't think that means much. I have a very short ratchet (a bit longer than my fist) that I used for 4 out of the 5 bolts, so I can't apply much torque, therefore I pretty much tightened them as much as I could, given the short handle.

One of the bolts is right under one of the tubes, so I couldn't get the ratchet under there and used a regular 12 pt wrench. Quite amateurish 😉
cali yarisCanoga Park, CA · Sep 20, 2009#115
Headers are difficult to get at back there, that is for sure. did you access the project from the top or from the bottom? just curious.

25 is pretty light.
fmicleSan Jose, CA, USA · Sep 20, 2009#116
Originally Posted by cali yaris ↑
Headers are difficult to get at back there, that is for sure. did you access the project from the top or from the bottom? just curious.

25 is pretty light.
Well, both ways, some things I did from under the hood - such as getting the old header out and the new one in, others from under the car - such as loosening 3 of the 5 header bolts, plus the spring bolts on the exhaust.

That's what I thought as well, 25 is pretty light and the gasket is metal, not something softer that I could squeeze and rip by overtightening...
kngrsllSpartanburg, SC · Sep 20, 2009#117
get a friend to help. i had one guy go from the top, i went from the bottom. it was MUCH easier.
kngrsllSpartanburg, SC · Sep 20, 2009#118
that post could be taken totally out of context btw
cali yarisCanoga Park, CA · Sep 20, 2009#119
LOL, I wasn't going to say it.
advocatelocation · Sep 20, 2009#120
Originally Posted by kngrsll ↑
that post could be taken totally out of context btw
It's a good thing you covered yourself them. 😆
hatchbackkid82. · Sep 21, 2009#121
With all the exhaust mods i have it's really not that loud, ,on the highway it isn't too bad if you don't step on it. Whe your outside the car though it is a lil loud, but no where near some other cars i.e. civic with test pipes. The mid pipe and exhaust will complement the header really well.

Originally Posted by kngrsll ↑
did you notice a difference with the mid pipe and exhaust? i didnt do those, i think the header had the best gains, and i dont want the noise/attention of an an exhaust.
chongopantsHouston · Nov 6, 2009#122
has anyone had problems re-using the stock gaskets? I am just of the old school ways where you replace them when you open it up... but I come from old V8s so should i go hunt down another gasket for my engine?
cali yarisCanoga Park, CA · Nov 6, 2009#123
Always best to throw on a new gasket -- better than having to do the job twice because you got a leak. You can definitetly re-use the donut from header to midpipe, though.

$14.45 at www.trdsparks.com
fmicleSan Jose, CA, USA · Nov 6, 2009#124
I reused the stock gasket and so far everything seems alright. How would I know if I had a leak? Is running idle enough to tell? I started it and sniffed around, listened, but it's all very quiet at idle, so I didn't hear anything...
vvvvvvvvvvvvvCalgary, AB, Canada · Aug 30, 2011#125
Originally Posted by hatchbackkid82 ↑
I have the afe intake, Nst pulley kit, DC header that i installed on Monday, nitto mid pipe, thunder axle back. It's an awesome combo of parts👍 The header does lose some low end but makes up for it, car has more punch in the mid and top end, ass dyno can feel the difference.
Did you have to modify the front flange of the Nitto midpipe to fit on the DC Sports header? I'd get the midpipe, but there was a notice about modifying the front flange to fit aftermarket headers....
hatchbackkid82. · Aug 31, 2011#126
Nope, no need to modify the flange on the DC header. I think it's probably the only one that doesn't need a flange modification. Make sure to get the Anti-Fouler otherwise your going to throw a CEL.
SeriousBlackBritish Columbia · Sep 12, 2011#127
The DC header was simple enough that my Toyota tech was able to do it in around .5 hrs during an oil change.

It was nice to have him see what a P.O.S. the OEM one is in comparison 😁
cali yarisCanoga Park, CA · Sep 13, 2011#128
^ those little stock collector tubes are so tiny!
rene0023Coamo, Puerto Rico · Mar 23, 2012#129
I have mine today and I installed it too. Thanks Garm. The DC was a great deal.
yariseggvvtiCali · Mar 23, 2012#130
what was the damage? I'm interesting putin header on 2. Thx!
DJYojimboChicago · Mar 26, 2012#131
Has anyone put a DC header in a 2012 Yaris yet?
Jason@SportsCarDebary, FL · Mar 26, 2012#132
Originally Posted by DJYojimbo ↑
Has anyone put a DC header in a 2012 Yaris yet?
Yes: 2012 mods/Parts
DJYojimboChicago · Mar 26, 2012#133
awesome thinking of getting a DC header and afe intake but might just stick to afe intake i really don't want to put an exhaust system or pulleys either. Thanks Jason!
Jason@SportsCarDebary, FL · Mar 27, 2012#134
Originally Posted by DJYojimbo ↑
awesome thinking of getting a DC header and afe intake but might just stick to afe intake i really don't want to put an exhaust system or pulleys either. Thanks Jason!
The header is an easy mod, and worth it.
1.5Tampa · Mar 27, 2012#135
Originally Posted by DJYojimbo ↑
awesome thinking of getting a DC header and afe intake but might just stick to afe intake i really don't want to put an exhaust system or pulleys either. Thanks Jason!
DC isnt going to really change your exhaust sound the intake and header is recommended. I have this exact set up. 👍
DJYojimboChicago · Mar 27, 2012#136
Yeah i just want a little more low end torque but i've heard i actually lose low end torque. 1.5 u said u just have an intake and dc headers no exhaust? I'm gonna go with that then :). Long live the yaris!
1.5Tampa · Mar 28, 2012#137
Yup that is my set up and it sounds pretty normal under easy driving. Once you climb up the powerband you can really see the mid-top range power coming and the sound is awesome! It makes a nice difference. Also everyone says to throw an anti fouler on but I am not using one for ~2k miles and no CEL.
DJYojimboChicago · Mar 28, 2012#138
Awesome thanks 1.5 and Jason! Gotta save my money for Garm hehe!
tizianoCH · Apr 2, 2012#139
Hallo
Wo hast du dann genau den DC-Header bestellt?
Hast du auch den Yaris 1,8l oder? Gab es bei dir Probleme bei der intallation der O2 Sonde?

Danke

Grüss Tiziano
tizianoCH · Apr 2, 2012#140
Hello
Where exactly did you then ordered the DC header?
Do you have the Yaris 1.8-liter is not it? Have there been problems with the intallation of O2 sensor?

Thank you

greet Tiziano
1.5Tampa · Apr 2, 2012#141
I got mine used off someone but microimageonline.com sells them and he does ship international. It is for the 1.5 idk if there is one for the 1.8
chewychewbaccaLong Beach, CA · Apr 9, 2012#142
DC Header is worth upgrading to. Car feels a lot more responsive throughout.
TrYarisTrois-Rivières, Qc · Nov 21, 2012#143
Hey guys, What is the difference between 4-2-1 and 4-1, in performance I mean
xnamerxxso cal · Nov 21, 2012#144
Depends on how they are designed, but if both are designed correctly there should be almost no difference.
tooterLos Angeles · Nov 21, 2012#145
Originally Posted by xnamerxx ↑
Depends on how they are designed, but if both are designed correctly there should be almost no difference.
The 1NZ FE engine's firing order is 1-3-4-2.

A 4-2-1 tri Y header pairs up sequentially firing cylinders 2-1 and 3-4 so that the exhaust pulse from one helps to draw exhaust from the other.

Picture not included in this copy

Picture not included in this copy

Then the combined 2-1 and 3-4 pairs join to help scavange each other...

Picture not included in this copy

Practically speaking, the headers are too short to make a lot of difference.

But that's where namer comes in... 😉
1.5Tampa · Nov 21, 2012#146
The 4-1 is supposed to delay the power increase until higher in the powerband. The 4-2-1 is supposed to give a midrange bump. On our tiny cars you probably would never notice a difference. I love my DC header. Anytime I'm above 4k I'm just roaring and pulling hard for a yaris lol.
tooterLos Angeles · Nov 21, 2012#147
I actually did notice a difference...
...as I climb a steep 1/4 mile hill in 2nd gear to get to my house. It's always the same hill, so that's constant. And driving up it everyday I have a good feeling for the resistance. The header definitely helped the engine make it up the hill easier. If you start climbing under 2,000 rpm, the engine labors sluggishly. But anything over 2,000 and it gains rpms much easier and climbs more easily than the stock header which feels like it's holding back at the same rpms.
cali yarisCanoga Park, CA · Nov 21, 2012#148
^ An aftermarket header will certainly make a difference over stock, but I doubt you can feel any difference BETWEEN aftermarket headers. You just can't feel 1-2 horsepower, in my opinion.
cali yarisCanoga Park, CA · Nov 21, 2012#149
TRYaris is that your car in your avatar?
xnamerxxso cal · Nov 21, 2012#150
Basically what Cali said.

There is a maximum of about 12" to work with and an ideal length of about 35" so most of the ots headers compensate by increasing the volume of tube which in essence give some of the same effect as increasing length but reduces scavenging at lower rpms. Now this motor is relatively small displacement with a good torque management system going to a larger diameter tube won't hurt you as bad as it would on a larger engine.

So not wanting to give up anywhere in the powerband while still gaining some up top is the reason I decided to design and build my own header.

As far as header type is concerned both a 4-2-1 and a 4-1 will accomplish the same goal but each design has its own advantages but both of them can produce near the same power and torque so there isn't a real advantage to choosing either one aside from packaging constraints, and a 4-1 is simply easier to package with the effecting lengths required.