Agreed. You can tell just by the pics/design that the DC is a waaaay better header.Originally Posted by kngrsll ↑dc, hands down...
DC Sports Header install and evaluation
202 posts · 149,038 views · page 2 of 5
Replies continued
That explains why so many hondas sound like crap 😆 Another question. Is anyone running this header with a nitto midpipe + axleback. I am afraid of dropping some torque due to lack of backpressure 🤷Originally Posted by Keith Tinari ↑header design (UEL, EL) can change the tone an exhaust has, but in this case the only thing that would really change the sound of this car is overall pipe diameter and status of the catalytic converters. When the pipe diameters dont all match up together and bottle neck you get that ricey farting with helium in your butt sound, when you lose your cats you get a raspy tone and that sounds worse when you couple it with a exhaust with uneven pipe diameters. You should try and stick to the same diameter piping as much as possible to maintain a smoother flow.
if you don't mind spending the extra $100 then get the DC...
FYI, the yaris header is really tiny , the most you'd get out of it just a matter 1 or 2 hp gain perhaps from one brand to another ....
just my 0.2cent...
FYI, the yaris header is really tiny , the most you'd get out of it just a matter 1 or 2 hp gain perhaps from one brand to another ....
just my 0.2cent...
I'm looking forward to receiving our shipment of DC Sports headers next week so that I can inspect them for myself.
They look excellent in pics and I'm sure our customers will be happy with their purchases.
👍👍
They look excellent in pics and I'm sure our customers will be happy with their purchases.
👍👍
Has anybody been on a dyno after doing this modification to see what kinds of actual gains there are, if any?
Sticky above^^^
HahahHahAAAAAAA!!!
I will install over the weekend. Now I'm only missing a few pieces of the N/A puzzle. Thanks for the header Garm. Great deal!!!
Picture not included in this copy
I will install over the weekend. Now I'm only missing a few pieces of the N/A puzzle. Thanks for the header Garm. Great deal!!!
Picture not included in this copy
yeah, shake it in the ayah, baby!! LOL
Finally got off my butt and placed my order with Garm for the DC. Looking forward to getting it. 🤘 Happy birthday to me! Happy birthday to me! 😁
Galavoxx - please post up how the install went and any tips/tricks. I would appreciate it! 👍 By the way, that header looks sharp!
Galavoxx - please post up how the install went and any tips/tricks. I would appreciate it! 👍 By the way, that header looks sharp!
I'm grippin' it too. Look at that white knuckle! LOL
I'll definitely let you guys know how it goes. I'm sure it'll be a piece of cake. I have all the tools needed, even a decent jack.
I'll definitely let you guys know how it goes. I'm sure it'll be a piece of cake. I have all the tools needed, even a decent jack.
Ha....dood be all kindsa "white-knuckled." It does look good...I am curious to hear your impression. 👍
I installed mine a few days ago, and IMO it was a pain in the ass. 😆
For some reason I had an absolute struggle to remove the second to right manifold bolt, the rest were easy enough though.
Feels a lot smoother to redline and my exhaust is now a bit throatier. (Custom 2 1/4" cat back to a Magnaflow Performance Muffler) Is nice. 😁
For some reason I had an absolute struggle to remove the second to right manifold bolt, the rest were easy enough though.
Feels a lot smoother to redline and my exhaust is now a bit throatier. (Custom 2 1/4" cat back to a Magnaflow Performance Muffler) Is nice. 😁
Well look at that! You're right here in my town! I wonder if I've seen your car before.... 🤷Originally Posted by Gideon ↑I installed mine a few days ago, and IMO it was a pain in the ass. 😆
For some reason I had an absolute struggle to remove the second to right manifold bolt, the rest were easy enough though.
Feels a lot smoother to redline and my exhaust is now a bit throatier. (Custom 2 1/4" cat back to a Magnaflow Performance Muffler) Is nice. 😁
Oh snap, so I am!Originally Posted by Herbicidal ↑Well look at that! You're right here in my town! I wonder if I've seen your car before.... 🤷
I'm over behind the Galleria off of Gibson.
I DID see a Yaris sedan of similar color and badassery making a right turn on Woodcreek Oaks Blvd. from Blue Oaks Blvd. once, maybe that was you? 😆
you should come to the meet w/ Gideon, Herbicidal! ;) LOL
man...more and more people are getting this header! damn....
Garm's new HIDs < Garm's DC header.... =_=
man...more and more people are getting this header! damn....
Garm's new HIDs < Garm's DC header.... =_=
Sorry folks for going OT on this thread, but Gideon you're right! That is my neighborhood! Too funny! We can exchange PM's if you like instead of here.Originally Posted by Gideon ↑Oh snap, so I am!
I'm over behind the Galleria off of Gibson.
I DID see a Yaris sedan of similar color and badassery making a right turn on Woodcreek Oaks Blvd. from Blue Oaks Blvd. once, maybe that was you? 😆
Kioshi - what meet? I guess I missed it. A PM with the info would be good. Thanks!
Back on topic, can't wait to get my header!
So I installed my DC Header on Saturday. It took me about an hour. I just jacked up the front of the car and placed it on jack stands and then went to work. I'm not going to go over how to install as others have already done this. Some things I thought about or should have though about during install (at length):
First of all, this header does not come with a doughnut (or a coffee) or a manifold gasket. I know, that sucks. However, I have 35k miles on my car and both the doughnut and the manifold gasket looked good. More on this later.
Remove your spark plug/plastic engine cover before trying to weasel the old header out. The plastic cover scratches super easy and I'm sort of a neat freak so I'm sort of pissed that I scratched mine, big scratch. The removal of the stock header was easy enough. Breaking the nuts and bolts loose was a little bit of an ass pain but they all came off a little effort. I would recommend you wear leather gloves for the task. Anyone whose ever had a wrench or a socket slip off and had a knuckle buster or has cut the Sh** out of themselves knows how valuable these gloves can be.
Not being able to see behind the motor while standing in front of the car was not a huge problem but it does require you use your "feelers" a lot more than your eyeballs. For me, most of the bolts were best broken loose standing in front of the car while they were best installed from underneath the car. This may not be true for you. The hardest bolt to remove and install was definitely the far left if you are sitting in the car facing forward. You really have to be a contortionist to get in there. That one probably took me ten minutes to remove, maybe more. You really need to be careful your socket or wrench has a good grip on the nut or bolt head. Stripping any one of these would absolutely suck.
Not to sound like a mom but another thing that sucks, getting rust in your eyes. Don't put your face under rusted bolts when removing them. Happened in the past, won't happen again. 😁
Installation of the new header was easy enough. I saved my doughnut, it was not crushed, deformed, or flaking. It looked good. Only issue is that it was stuck on the old header. I took a small flat head screwdriver and worked around the base of the doughnut, separating it little by little from the old header and working to a larger screwdriver, taking care not to damage the thing. Once loose enough I was able remove by twisting the doughnut back and forth. Try twisting before screwdrivers as yours might just come off. If you don't know what it's supposed to look like just buy a new one at your local muffler shop, should be under $10.
The manifold gasket was easier. After the old header is off it will fall behind the engine or you can reach back and take it off it's from where it's perched on the head.
Special Advertising section:
Now my dirty little secret and lifesaver for many vintage motor projects. It's called Ultra Copper and is made by Permatex!! It comes in a spray can. I'm sure some of you know about this stuff, if you don't and you work on old cars or any cars or motorcycles, you should always have a can. It is aMAzing!! Somebody turned me onto it when I had a vintage motorcycle that no longer had parts being produced and I had no money to get them custom made. At that time I was using it for a compression ring head gasket. Since then I have used it for anything from valve cover gaskets, motorcycle clutch cover gaskets, any paper gasket, cork gasket, or concrete gasket, anything on a motor that will touch gas, oil, or heat or all combined. I have never had a gasket fail when this stuff was applied. No joke. So I busted it out for the already used manifold gasket and gave it a few coats before re-installing. This stuff is sticky so it also helps to hold the gasket in place while you put your part on top of it and bolt it up. Also make sure to clean the old gasket of any rust or carbon. I don't see a need to use this stuff on the doughnut but I'm sure it wouldn't hurt. Basically this stuff is a sticky copper infused spray gasket that is supposed to fill imperfections between the gasket and mating surface. I'm not trying to explain the science behind it, I just know it has always worked for me. If you are going to re-use a gasket or even when using a new one, apply this stuff for best results. 👍
The only issue I found with the install apart from the font left bolt being a pain was that my torque wrench was too big to fit into the tight space of the engine bay. I torqued the two collector bolts with the springs to the proper 32 ft lbs but two manifold bolts and three nuts to 20lbs, those had to be done with faith. Maybe someone else can comment on what torque wrench they used, if any. I'm assuming the factory torquing is done while the motor is out of the car so they give you these numbers assuming you can reach the damn things. Or maybe there is a baby torque wrench that I need to add to my tool collection.
After install I noticed that the A/F sensor plug wire was a little tighter than I might like. Nothing to be done. This is probably due to the bung being located lower on the header than the stock bung location.
I tried to drive the car as much as possible this weekend but was pretty busy. Based on about an hour of driving, maybe a little more, I have to agree with others that I have definitely lost some low end torque. The car does not want to climb hills below 3000 rpms in second gear, which I used to be able to do. I'm in San Francisco so this matters. There are many hills.
The car feels smoother to redline but I really can't tell if it's gained any peak horsepower, maybe a few, maaaybe, but it's really really hard to tell without a dyno. Also pure speculation without a dyno: I think what has happened is a few more hp have become available in the mid range and connected that area of the power band to the upper end of the power band. Horsepower feels like it comes in earlier around 3800 rpms and then continues to rev and grow very smoothly up to peak hp at close to redline. What I used to think was the VVTi kicking in (and maybe it was), a surge of power between like 4700 and 6500 rpms, that is gone. Now the motor just revs straight through to redline with no surging. This is especially noticeable getting on the highway.
In the end I don't know if this is a worthwhile upgrade until Garm's intake manifold comes out (assuming it happens and assuming the intake makes power). The fit and finish of the DC header is great but even with larger exhaust piping from the cat back to a Nitto Muffler, a WeaponR short ram, and the light crank pulley, the header doesn't give a huge amount of bang for your buck. I think the intake side is choking it. If you simply must have a header I would hit up one of the cheaper options. I'm glad I bought this header because I wanted a header and like a quality product and this is definitely both. I wasn't expecting huge gains so I'm not disappointed. I think I will miss that little bit of low end torque though.
So far no exhaust leaks.
I do have one question as I'm not very savvy on the ECU side. Will the ECU make any adjustments for the addition of more flow on the backside? It seems like the car got more power the more I drove it. That could have also been differences in intake temperatures or something though.
First of all, this header does not come with a doughnut (or a coffee) or a manifold gasket. I know, that sucks. However, I have 35k miles on my car and both the doughnut and the manifold gasket looked good. More on this later.
Remove your spark plug/plastic engine cover before trying to weasel the old header out. The plastic cover scratches super easy and I'm sort of a neat freak so I'm sort of pissed that I scratched mine, big scratch. The removal of the stock header was easy enough. Breaking the nuts and bolts loose was a little bit of an ass pain but they all came off a little effort. I would recommend you wear leather gloves for the task. Anyone whose ever had a wrench or a socket slip off and had a knuckle buster or has cut the Sh** out of themselves knows how valuable these gloves can be.
Not being able to see behind the motor while standing in front of the car was not a huge problem but it does require you use your "feelers" a lot more than your eyeballs. For me, most of the bolts were best broken loose standing in front of the car while they were best installed from underneath the car. This may not be true for you. The hardest bolt to remove and install was definitely the far left if you are sitting in the car facing forward. You really have to be a contortionist to get in there. That one probably took me ten minutes to remove, maybe more. You really need to be careful your socket or wrench has a good grip on the nut or bolt head. Stripping any one of these would absolutely suck.
Not to sound like a mom but another thing that sucks, getting rust in your eyes. Don't put your face under rusted bolts when removing them. Happened in the past, won't happen again. 😁
Installation of the new header was easy enough. I saved my doughnut, it was not crushed, deformed, or flaking. It looked good. Only issue is that it was stuck on the old header. I took a small flat head screwdriver and worked around the base of the doughnut, separating it little by little from the old header and working to a larger screwdriver, taking care not to damage the thing. Once loose enough I was able remove by twisting the doughnut back and forth. Try twisting before screwdrivers as yours might just come off. If you don't know what it's supposed to look like just buy a new one at your local muffler shop, should be under $10.
The manifold gasket was easier. After the old header is off it will fall behind the engine or you can reach back and take it off it's from where it's perched on the head.
Special Advertising section:
Now my dirty little secret and lifesaver for many vintage motor projects. It's called Ultra Copper and is made by Permatex!! It comes in a spray can. I'm sure some of you know about this stuff, if you don't and you work on old cars or any cars or motorcycles, you should always have a can. It is aMAzing!! Somebody turned me onto it when I had a vintage motorcycle that no longer had parts being produced and I had no money to get them custom made. At that time I was using it for a compression ring head gasket. Since then I have used it for anything from valve cover gaskets, motorcycle clutch cover gaskets, any paper gasket, cork gasket, or concrete gasket, anything on a motor that will touch gas, oil, or heat or all combined. I have never had a gasket fail when this stuff was applied. No joke. So I busted it out for the already used manifold gasket and gave it a few coats before re-installing. This stuff is sticky so it also helps to hold the gasket in place while you put your part on top of it and bolt it up. Also make sure to clean the old gasket of any rust or carbon. I don't see a need to use this stuff on the doughnut but I'm sure it wouldn't hurt. Basically this stuff is a sticky copper infused spray gasket that is supposed to fill imperfections between the gasket and mating surface. I'm not trying to explain the science behind it, I just know it has always worked for me. If you are going to re-use a gasket or even when using a new one, apply this stuff for best results. 👍
The only issue I found with the install apart from the font left bolt being a pain was that my torque wrench was too big to fit into the tight space of the engine bay. I torqued the two collector bolts with the springs to the proper 32 ft lbs but two manifold bolts and three nuts to 20lbs, those had to be done with faith. Maybe someone else can comment on what torque wrench they used, if any. I'm assuming the factory torquing is done while the motor is out of the car so they give you these numbers assuming you can reach the damn things. Or maybe there is a baby torque wrench that I need to add to my tool collection.
After install I noticed that the A/F sensor plug wire was a little tighter than I might like. Nothing to be done. This is probably due to the bung being located lower on the header than the stock bung location.
I tried to drive the car as much as possible this weekend but was pretty busy. Based on about an hour of driving, maybe a little more, I have to agree with others that I have definitely lost some low end torque. The car does not want to climb hills below 3000 rpms in second gear, which I used to be able to do. I'm in San Francisco so this matters. There are many hills.
The car feels smoother to redline but I really can't tell if it's gained any peak horsepower, maybe a few, maaaybe, but it's really really hard to tell without a dyno. Also pure speculation without a dyno: I think what has happened is a few more hp have become available in the mid range and connected that area of the power band to the upper end of the power band. Horsepower feels like it comes in earlier around 3800 rpms and then continues to rev and grow very smoothly up to peak hp at close to redline. What I used to think was the VVTi kicking in (and maybe it was), a surge of power between like 4700 and 6500 rpms, that is gone. Now the motor just revs straight through to redline with no surging. This is especially noticeable getting on the highway.
In the end I don't know if this is a worthwhile upgrade until Garm's intake manifold comes out (assuming it happens and assuming the intake makes power). The fit and finish of the DC header is great but even with larger exhaust piping from the cat back to a Nitto Muffler, a WeaponR short ram, and the light crank pulley, the header doesn't give a huge amount of bang for your buck. I think the intake side is choking it. If you simply must have a header I would hit up one of the cheaper options. I'm glad I bought this header because I wanted a header and like a quality product and this is definitely both. I wasn't expecting huge gains so I'm not disappointed. I think I will miss that little bit of low end torque though.
So far no exhaust leaks.
I do have one question as I'm not very savvy on the ECU side. Will the ECU make any adjustments for the addition of more flow on the backside? It seems like the car got more power the more I drove it. That could have also been differences in intake temperatures or something though.
Galavoxx - GREAT write up! And thanks too for the tips and tricks. I'm a little bummed to hear that you lost some low end torque. I was hoping to gain some in that area. I too am curious about resetting the ECU and whether it should be done or not for a header?
I may be thinking wrong but any time you perform a mod that is supposed to increase power you are supposed to disconnect the battery to reset the ECU? Like I said I'm not 100% sure about that
Very nice review Galavoxx!
Shameless plug coming next...
perhaps you should try an Underdrive Crank Pulley to help you regain some of that low end torque. Should be very helpful for hill climbing!
Good luck and have fun with all your projects!
Shameless plug coming next...
perhaps you should try an Underdrive Crank Pulley to help you regain some of that low end torque. Should be very helpful for hill climbing!
Good luck and have fun with all your projects!
^ Shameless! -- good suggestion too! 😆
LOL. Is the underdrive really going to help that much? I already have your lightened crank pulley. Plus, I'm saving for a rainy custom intake day.Originally Posted by NonStopTuning ↑Very nice review Galavoxx!
Shameless plug coming next...
perhaps you should try an Underdrive Crank Pulley to help you regain some of that low end torque. Should be very helpful for hill climbing!
Good luck and have fun with all your projects!
Anyone have any comments on the ECU question?
Well, you have changed the amount of air (and fuel) passing through the motor. So your ECU will definitely "notice" that and be making some adjustments (= "relearn"). I'm not sure you have to reset it for it to do that, but it's not a bad idea.
You should. When I installed the headers for the first time I didnt d/c the battery and I got CEL after a few minutes driving. Reset the battery and you shouldn't get a CEL ever assuming installation was done correctly. Running some crap ebay headers with no problems for a month now. :)Originally Posted by lilredrocket ↑I may be thinking wrong but any time you perform a mod that is supposed to increase power you are supposed to disconnect the battery to reset the ECU? Like I said I'm not 100% sure about that
I didn't throw a CEL but I'll disconnect overnight and see how it feels afterward.
You may want to rev it up acouple time after you start it back up to help the ECU out a little.
Fantastic write-up! I will definitely hold off on this mod. Thanks again for the great post.
Hmmm... I read about that trick. I'm a little skeptical but I'll definitely go on a drive afterward, give it some juice.
Can someone please explain the physics of why would you lose some low-end torque with a less restrictive header? It's not quite intuitive to me, as to why that would happen, but I admit I'm not a mechanic 🤷
It's too late for me anyway, as I ordered mine last week 🙂 but I'd still like to understand what happens there.
It's too late for me anyway, as I ordered mine last week 🙂 but I'd still like to understand what happens there.
I don't know the physics behind it but I'm assuming it has to do the scavenging properties of the new header. The header doesn't take the exhaust gasses away fast enough at low RPMS due to an increased volume in tubing. The pressure in the manifold is probably too low. Once the engine begins to rev higher and the exhaust pressure begins to rise, that additional volume gets put to use and allows for the exhaust gasses to be expelled more quickly and freely than that stock header that was on there. I could be completely wrong but that's my experience with two-stroke motorcycle stuff talking. I imagine the principles are the same.
slimmer tube....faster flow and the interior geometry and surface finish also matters. A fatter tube with such a weak motor and you will feel the loss in torque due to less velocity. Don't forget, the car was designed/engineered as a whole unit which means that the overall efficiency is probably maximized with the stock exhaust header. Add some other modifications and well....that story might not hold truth any longer.
Galavoxx - Based upon your write up, particulary regarding your comments above, I changed my order with Garm from the DC to the Megan. The Megan header arrived yesterday and looks good to me (thanks Garm!). We'll see if I made the right decision. I did save some coin by switching and perhaps I'll use the difference to buy a higher flowing air filter. I hope to find an hour or two this weekend to do the install. I think I will pick up some of that Permatex Ultra Copper first.Originally Posted by Galavoxx ↑...I tried to drive the car as much as possible this weekend but was pretty busy. Based on about an hour of driving, maybe a little more, I have to agree with others that I have definitely lost some low end torque. The car does not want to climb hills below 3000 rpms in second gear, which I used to be able to do. I'm in San Francisco so this matters. There are many hills...
...If you simply must have a header I would hit up one of the cheaper options. I'm glad I bought this header because I wanted a header and like a quality product and this is definitely both. I wasn't expecting huge gains so I'm not disappointed. I think I will miss that little bit of low end torque though...
I disconnected the battery for a couple of hours today and went for a heavy footed drive up and down highway 280 and then up and down some hills.
At first it seemed like nothing was different. This is probably because I was skeptical the ECU would change anything given I had already driven the car for 100 miles or so.
Well, I was totally wrong. The low end torque feels like it's back! I did some "tests" up some of the steeper hills in my neighborhood and I can definitely feel more power down low. I don't know the exact extent of the change when compared to the stock header but the throttle response really is better and the engine just feels like it has better pull than before the ECU reset. I can say that disconnecting the ECU definitely helped things and anyone adding a header should probably perform the reset. I'm going to go on an early drive up highway 1 to Tamales Bay tomorrow morning, grab some breakfast and see if it gets even better!! Thank you all for the suggestion.
At first it seemed like nothing was different. This is probably because I was skeptical the ECU would change anything given I had already driven the car for 100 miles or so.
Well, I was totally wrong. The low end torque feels like it's back! I did some "tests" up some of the steeper hills in my neighborhood and I can definitely feel more power down low. I don't know the exact extent of the change when compared to the stock header but the throttle response really is better and the engine just feels like it has better pull than before the ECU reset. I can say that disconnecting the ECU definitely helped things and anyone adding a header should probably perform the reset. I'm going to go on an early drive up highway 1 to Tamales Bay tomorrow morning, grab some breakfast and see if it gets even better!! Thank you all for the suggestion.
Hey Herb (haha)... I'm curious to know if your low end suffers at all. After the ECU reset mine feels like is probably back to where it was at stock. Let us know what you think after you've installed.Originally Posted by Herbicidal ↑Galavoxx - Based upon your write up, particulary regarding your comments above, I changed my order with Garm from the DC to the Megan. The Megan header arrived yesterday and looks good to me (thanks Garm!). We'll see if I made the right decision. I did save some coin by switching and perhaps I'll use the difference to buy a higher flowing air filter. I hope to find an hour or two this weekend to do the install. I think I will pick up some of that Permatex Ultra Copper first.
Will do! Enjoy your drive up hwy 1! 👍Originally Posted by Galavoxx ↑Hey Herb (haha)... I'm curious to know if your low end suffers at all. After the ECU reset mine feels like is probably back to where it was at stock. Let us know what you think after you've installed.
Glad to hear that helped
Galavoxx
Great to hear. I hope it gets even better for you tomorrow.
Great to hear. I hope it gets even better for you tomorrow.
🤘 whew, good, 'cause I've already ordered mine 👍Originally Posted by Galavoxx ↑...
Well, I was totally wrong. The low end torque feels like it's back!
...
Galavoxx -how was your drive up hwy 1?
I having removal issues with my air/fuel sensor (on the stock manifold), so my car is still up on jack stands while my Toyota mechanic buddy tries to get it un-stuck. He has the old manifold at his house. I think I'll need to post up my experience with the Megan install. It was going fine until the stuck sensor. Oh well, there is always something! Oh yeah, air tools are your friend! 👍
I having removal issues with my air/fuel sensor (on the stock manifold), so my car is still up on jack stands while my Toyota mechanic buddy tries to get it un-stuck. He has the old manifold at his house. I think I'll need to post up my experience with the Megan install. It was going fine until the stuck sensor. Oh well, there is always something! Oh yeah, air tools are your friend! 👍
I hate it when the little things hold up a project, very frustrating. Hopefully you get it out of there. Mine came right out.
As for my drive, it went well. It was foggy as hell but the car ran pretty strong. I like the header. It's not a huge improvement over my old setup but it is noticeable.
As for my drive, it went well. It was foggy as hell but the car ran pretty strong. I like the header. It's not a huge improvement over my old setup but it is noticeable.
does anyone know if this is CARB legal? i may be moving to cali next year. i did a search and found that supposedly all DC headers are CARB exempt, but i cant find a specific # for this one.
Well, from my [little] research on the subject, I believe the CARB law says no modifications to intake and exhaust are allowed. Manufacturers can apply for exemptions. When these exemptions are granted, the part receives an EO (Executive Order) number, which makes it legal.Originally Posted by kngrsll ↑does anyone know if this is CARB legal? i may be moving to cali next year. i did a search and found that supposedly all DC headers are CARB exempt, but i cant find a specific # for this one.
Since the header is a modification to the exhaust, it is thereby illegal. As far as I know there are no exempt aftermarket parts for the Yaris. That is anything that has to do with intake and exhaust.
I have the AEM air intake and asked them if the exemption application is pending or if they plan to do it and they replied: no, there is no exemption, there is no plan to apply and your intake is for off-road use only. 🙄
I know the DMV fined some dealers in the greater LA area a few years back because they were selling sport vehicles with mods that were not CARB approved.
If you asked me, I'd say there is no way a mod that improves my gas mileage is bad for anyone (including the environment), but these are the rules... I don't understand why I can't install an aftermarket CAI on my 2007 engine, but one of the guys at work can still drive a 1982 Honda Civic with carburetor and choke and such. Even if I toss the catalytic converter, he still beats me by a wide mile in terms of emissions 🙄
Like I said, these are the rules. I guess the Yaris is not a popular enough vehicle to make it worthwhile for manufacturers to go through the exemption process. Just my guess...
Oh, and don't worry, CA is not that bad a place to live, after all 😉Originally Posted by kngrsll ↑does anyone know if this is CARB legal? i may be moving to cali next year. i did a search and found that supposedly all DC headers are CARB exempt, but i cant find a specific # for this one.
I was wondering the same thing... I have JBA headers on my 01' Tundra and they do have a CARB #. It will be interesting to see if the technician at my first smog test for the Yaris will even notice it has a header back there. 🤷Originally Posted by kngrsll ↑does anyone know if this is CARB legal? i may be moving to cali next year. i did a search and found that supposedly all DC headers are CARB exempt, but i cant find a specific # for this one.
On another note, my Toyota buddy was able to finally remove the air/fuel sensor from the stock manifold, but the threads were wasted. Fortunately he had a used spare that he gave to me. It's almost all back together, maybe tomorrow I'll be able to finish it up. The battery is currently disconnected. Once I'm all done, I think I will start a new thread on my Megan header install experience as this thread really isn't the place.
No love for me with my air/fuel sensor. 😢 Tried a couple of used ones that had matching part numbers but came from different model Toyota's. All threw a CEL. Gave up and asked my buddy to pick up a new one and call it done. I should have the new sensor installed this evening.
This became a rather expensive mod. 🙄
This became a rather expensive mod. 🙄
That sucks. Hopefully you like the header.
Thanks. Question for you - were you able to reuse the Toyota bolts to connect the DC header to the mid-pipe? These have the big spring around the bolt. How about the bolt to reconnect the support bracket from behind the block to the header?Originally Posted by Galavoxx ↑That sucks. Hopefully you like the header.
Just ordered mine from wesellcarparts, woohoo!!!!!
Sorry for the delay. Yes, I re-used all bolts including the spring loaded collector bolt. They were all in excellent condition, even after $35K miles.Originally Posted by Herbicidal ↑Thanks. Question for you - were you able to reuse the Toyota bolts to connect the DC header to the mid-pipe? These have the big spring around the bolt. How about the bolt to reconnect the support bracket from behind the block to the header?
One thing I didn't mention in my original post, I don't know if this is just my car but there is a threaded tab on the side of the header (new and old) that wasn't connected to anything and doesn't appear that it could be. Is this supposed to connect to the "support bracket" you are talking about? If so, my car didn't come with a support bracket.