Yarisworld Archive

DIY - Bypassing Tire Pressure Warning System (TPWS / TPMS)

217 posts · 385,870 views · page 2 of 5

Replies continued

ChupacabraCT · Nov 30, 2008#51
awesome write-up Scott!
blacksandiegovitzJust chillin' out brah ! · Nov 30, 2008#52
Yes , you got it too work , thats great ! Thanks for doing the research/testing for this fix . I'll be doing this within the next couple days , im so over that damn light in the dash.
CTScottThread starterUSA, CT · Dec 2, 2008#53
Please look at the directons on page 3. Based on feedback of mixed results, I changed the resistor value as the original value was causing a valtage drop that put it on the edge, where it would work on some cars and not on others.
ivanmadelineNC · Dec 2, 2008#54
Originally Posted by CTScott ↑
Please look at the directons on page 3. Based on feedback of mixed results, I changed the resistor value as the original value was causing a valtage drop that put it on the edge, where it would work on some cars and not on others.
I tried doin it on Sunday but the problem I had was that when I hit the button the light would start flashing the it would come on then I hit the button again and the same thing it would just flash for a few minutes and then stay on again.
I dont know if this makes a difference but i Dont have a brown cable on mine I have a white with a black stripe were that brown one is on your write up. Any suggetions. thanks for all your help.👍
CTScottThread starterUSA, CT · Dec 2, 2008#55
Originally Posted by ivanmadeline ↑
I tried doin it on Sunday but the problem I had was that when I hit the button the light would start flashing the it would come on then I hit the button again and the same thing it would just flash for a few minutes and then stay on again.
I dont know if this makes a difference but i Dont have a brown cable on mine I have a white with a black stripe were that brown one is on your write up. Any suggetions. thanks for all your help.👍
Can you take a picture of your connector? The part number is the same for 08 and 09 sedans and LBs, so even though the wire colors are different, their functions are identical.

If your connections are in the correct place, try measuring the voltage on the "brown" wire with the switch in both modes. With the TPWS connected (and the sensors not present) you will read ~1 VDC. Withe the TPWS bypassed you should read ~4 VDC. If the voltage is less than 3 VDC, the light will remain on.

If you do measure less than 3 VDC, you will need to change the resistiors to 150 ohm, 1/2 watt ones.
ivanmadelineNC · Dec 2, 2008#56
Originally Posted by CTScott ↑
Can you take a picture of your connector? The part number is the same for 08 and 09 sedans and LBs, so even though the wire colors are different, their functions are identical.

If your connections are in the correct place, try measuring the voltage on the "brown" wire with the switch in both modes. With the TPWS connected (and the sensors not present) you will read ~1 VDC. Withe the TPWS bypassed you should read ~4 VDC. If the voltage is less than 3 VDC, the light will remain on.

If you do measure less than 3 VDC, you will need to change the resistiors to 150 ohm, 1/2 watt ones.

I'll try again this weekend thanks.
linnyMn · Dec 3, 2008#57
Installed the 150 Ohm resistor harness yesterday and no more light!! Took a 60 mile drive last night and 3 mile work commute today and all is still great!
Pitt YarisPittsburgh · Dec 5, 2008#58
i haven't checked my pressure lately, but everything is stock on mine....the light came on when it got cold out, and hasn't turned off since. car is two months old
mikenacaratoBrentwood, TN · Dec 5, 2008#59
add some air
ivanmadelineNC · Dec 7, 2008#60
Originally Posted by CTScott ↑
Can you take a picture of your connector? The part number is the same for 08 and 09 sedans and LBs, so even though the wire colors are different, their functions are identical.

If your connections are in the correct place, try measuring the voltage on the "brown" wire with the switch in both modes. With the TPWS connected (and the sensors not present) you will read ~1 VDC. Withe the TPWS bypassed you should read ~4 VDC. If the voltage is less than 3 VDC, the light will remain on.

If you do measure less than 3 VDC, you will need to change the resistiors to 150 ohm, 1/2 watt ones.
Hey CTScott thank to you the light is gone. The first time the light came on again but when I got home I change the blue and the yellow cable around and the light was on I click the switch and the light is gone. Thanks for all your hard work.👍
IllusionXBrossard, QC · Dec 9, 2008#61
Scott, do you have a picture of that light ?
CTScottThread starterUSA, CT · Dec 9, 2008#62
Originally Posted by IllusionX ↑
Scott, do you have a picture of that light ?
It is the one that looks like this:

Picture lost · www.carbuyersnotebook.com
IllusionXBrossard, QC · Dec 9, 2008#63
thank you.
Black YarisToledo, OH · Dec 9, 2008#64
so is this latest fix 100% working, with no problems?
ivanmadelineNC · Dec 9, 2008#65
Originally Posted by Black Yaris ↑
so is this latest fix 100% working, with no problems?

I can let you know tomorrow I just got done changing the resistior to the 150 omh 1/2 watt. I had the 10 ohm that i install the first time and the light would stay off the first day and it would come back on the next day after the first 15 min ride.
linnyMn · Dec 10, 2008#66
I put in the 150 Ohm resistor mod on Dec 2 and have had no problems in the ~150 miles I have driven since. I did not do the switch procedure as I do not intend to EVER go back to a TPMS. I personally see absolutely no value in TPMS whatsoever for me.
SO, if I ever buy another new car I will do this all over again!
ivanmadelineNC · Dec 11, 2008#67
Originally Posted by Black Yaris ↑
so is this latest fix 100% working, with no problems?
Yes it does work the 2nd day in the road no light. With no switch.👏
blacksandiegovitzJust chillin' out brah ! · Dec 15, 2008#68
Still working with the 150 ohm resistor modd????
linnyMn · Dec 16, 2008#69
It is still working for me!🤘
09TRDRI · Dec 18, 2008#70
Just to verify:

If one chooses to do this mod without the switch, the connector remains UNPLUGGED from the TPWS module?
CTScottThread starterUSA, CT · Dec 18, 2008#71
Originally Posted by 09TRD ↑
Just to verify:

If one chooses to do this mod without the switch, the connector remains UNPLUGGED from the TPWS module?
Correct.
TiddlygooseNew Hampshire · Jan 20, 2009#72
OK, so I followed the first mod as CTScott knows... Then I followed the corrected 2nd version of the mod. I Left the first switch in the on position, Added a second push button switch with the 3 150 ohm resistors and it worked right up until the time I got up to highways speed. Then the darned light came back on. No amount of changing either switch changes anything at all.

Question. Can the dealer disable the entire TPMS system, even if it costs me? Has anyone had that done or know anything? I always check my own damed tires. I've never had anything like this to fall back on before and with my tire switching situation I'd just as soon loose TPMS all together at this point.
CTScottThread starterUSA, CT · Jan 20, 2009#73
Originally Posted by Tiddlygoose ↑
OK, so I followed the first mod as CTScott knows... Then I followed the corrected 2nd version of the mod. I Left the first switch in the on position, Added a second push button switch with the 3 150 ohm resistors and it worked right up until the time I got up to highways speed. Then the darned light came back on. No amount of changing either switch changes anything at all.

Question. Can the dealer disable the entire TPMS system, even if it costs me? Has anyone had that done or know anything? I always check my own damed tires. I've never had anything like this to fall back on before and with my tire switching situation I'd just as soon loose TPMS all together at this point.
The dealer can't disable it.

Can you take some pictures of your wiring, so I can help you troubleshoot it?

Mine has been running fine disabled (no light) since I posted the updated version on 11/30/08.
blacksandiegovitzJust chillin' out brah ! · Jan 20, 2009#74
Originally Posted by CTScott ↑
The dealer can't disable it.

Can you take some pictures of your wiring, so I can help you troubleshoot it?

Mine has been running fine disabled (no light) since I posted the updated version on 11/30/08.
I haven't even ef'd with the fix yet. I got just about every damn warning light on cause I switched steering wheel , rims, seats, seatbelts. At this point its probaly just easier for me to pull out the gauge cluster and pull the light bulbs out , Lol.
TiddlygooseNew Hampshire · Jan 21, 2009#75
Originally Posted by CTScott ↑
The dealer can't disable it.

Can you take some pictures of your wiring, so I can help you troubleshoot it?

Mine has been running fine disabled (no light) since I posted the updated version on 11/30/08.
Cool, I appreciate it. I think at this point I shall wait until it warms up above freezing. I nearly got frostbite on my fingers when I did this a few weeks ago... I will live with the light for now.
linnyMn · Jan 23, 2009#76
I am still happily driving around TPWS light FREE!! I followed the 150 ohm procedure without a switch.
ivanmadelineNC · Jan 24, 2009#77
Originally Posted by linny ↑
I am still happily driving around TPWS light FREE!! I followed the 150 ohm procedure without a switch.

Like Linny Still no light 👍
ricktoyota73Kalamazoo, MI · Feb 25, 2009#78
Ok, so on a new project, I should use 130 ohm resistors, correct?
I have a bunch of 20 guage wire. Is that ok to use?
CTScott...how did you figure this shit out?
I have been working in the parts department of car dealers for the last 10 years and, from the things I've seen over the years, you never want to cut the factory wire harness. I will definitely leave enough wire where I can reconnect the SOB, but it still scares the crap out of me. It will be worth it to get rid of the cursed light, though.
CTScottThread starterUSA, CT · Feb 25, 2009#79
Originally Posted by ricktoyota73 ↑
Ok, so on a new project, I should use 130 ohm resistors, correct?
I have a bunch of 20 guage wire. Is that ok to use?
CTScott...how did you figure this shit out?
I have been working in the parts department of car dealers for the last 10 years and, from the things I've seen over the years, you never want to cut the factory wire harness. I will definitely leave enough wire where I can reconnect the SOB, but it still scares the crap out of me. It will be worth it to get rid of the cursed light, though.
110 to 150 ohm resistors will work - Just make sure they are 1/2 Watt.

Cutting into factory harnesses can be dangerous if you don't know what you are doing. I design more complex systems for a living, so I enjoy reverse engineering automotive systems.
ricktoyota73Kalamazoo, MI · Feb 26, 2009#80
Originally Posted by CTScott ↑
110 to 150 ohm resistors will work - Just make sure they are 1/2 Watt.

Cutting into factory harnesses can be dangerous if you don't know what you are doing. I design more complex systems for a living, so I enjoy reverse engineering automotive systems.
I sell auto parts and I honestly don't understand how half of this stuff works!
Thanks for the info. Hooking it up as soon as we get a weekend above freezing and I can stand to be out in the garage for a while.
ricktoyota73Kalamazoo, MI · Mar 17, 2009#81
Just curious, if I'm not putting in a switch and don't care if I ever enable the system again, can I just cut and connect the wires to the resistor package instead of using tap splices?
CTScottThread starterUSA, CT · Mar 17, 2009#82
Originally Posted by ricktoyota73 ↑
Just curious, if I'm not putting in a switch and don't care if I ever enable the system again, can I just cut and connect the wires to the resistor package instead of using tap splices?
Yes you can.

I wrote it up with use of the tap splices keeping in mind that many people are not comfortable soldering under the dash (and in relatively close proximity to the passenger air bag).
ricktoyota73Kalamazoo, MI · Mar 17, 2009#83
So, just using butt connectors not a good idea (uh huh huh huh...I said "butt" huh huh)?
mikenacaratoBrentwood, TN · Mar 17, 2009#84
Originally Posted by ricktoyota73 ↑
Just curious, if I'm not putting in a switch and don't care if I ever enable the system again, can I just cut and connect the wires to the resistor package instead of using tap splices?
thats what i did and it works fine, i even removed both TPMS modules, one under the dash and one in the paneling behind the trunk. theres a good .02 lbs and weight saved! 👍
ricktoyota73Kalamazoo, MI · Mar 17, 2009#85
Funny about the weight savings!
CTScottThread starterUSA, CT · Mar 17, 2009#86
Originally Posted by ricktoyota73 ↑
So, just using butt connectors not a good idea (uh huh huh huh...I said "butt" huh huh)?
Butt connectors are fine - Just don't use big ones (unless you like that kind of thing...)
regalPA · Mar 23, 2009#87
When doing this will there still be an OBDII code? I ask because to pass emissions in PA you can't have any OBDII codes.
CTScottThread starterUSA, CT · Mar 23, 2009#88
Originally Posted by regal ↑
When doing this will there still be an OBDII code? I ask because to pass emissions in PA you can't have any OBDII codes.
The TPWS does not report codes over OBDII, so you should be fine. It's data is accessible over the CAN bus, but a Toyota specific communication tool is required to access the data.
AznGoukiCalgary · Apr 13, 2009#89
Does every yaris have it? I have the base with no AC 08. Any way to verify before I start looking for the module?
TaiyakiHonolulu, HI · May 19, 2009#90
Ok so to get rid of it without a switch all you have to do it start off with the light not on, turn off the car, unplug the thing, and cut the green and brown wire and connect them to eachother, and leave the harness unplugged?
gwasabiHonolulu, Hawaii · May 19, 2009#91
no i think u gotta put resisters in between?
CTScottThread starterUSA, CT · May 19, 2009#92
Originally Posted by Taiyaki ↑
Ok so to get rid of it without a switch all you have to do it start off with the light not on, turn off the car, unplug the thing, and cut the green and brown wire and connect them to eachother, and leave the harness unplugged?
Jump to post 45 and you'll see the resistor voltage divider. You need to make one of those up. Clipping the wires turned out to not work.
TaiyakiHonolulu, HI · May 20, 2009#93
Ok i think ill just put a switch in it.
CTScottThread starterUSA, CT · May 20, 2009#94
Originally Posted by Taiyaki ↑
Ok i think ill just put a switch in it.

Just to clarify; adding the switch doesn't really make it any easier. If you want to do it without the switch, you build the voltage divider shown below (from page 3 of this thread). You unplug the TPWS connector (and leave it disconnected) and connect the red wire to the red wire show below, the black wire to the white wire shown below, and you connect the green wire to the brown wire below.

The switch method is just for people who run two sets of rims with one of the two sets still having the sensors installed.








TaiyakiHonolulu, HI · May 25, 2009#95
Ok so a few days ago I did this. I added a switch. And it worked perfect for a few days. But now the light flashes and when I turn the switch off is stays on (doesn't flash).
CTScottThread starterUSA, CT · May 25, 2009#96
Originally Posted by Taiyaki ↑
Ok so a few days ago I did this. I added a switch. And it worked perfect for a few days. But now the light flashes and when I turn the switch off is stays on (doesn't flash).
Measure the voltage on the brown wire.
regalPA · May 26, 2009#97
I'm not getting any voltage off the brown, white, or red wire, where is the fuse for this thing?
CTScottThread starterUSA, CT · May 26, 2009#98
Originally Posted by regal ↑
I'm not getting any voltage off the brown, white, or red wire, where is the fuse for this thing?
It's the ECU-IG 10A fuse.
regalPA · May 26, 2009#99
Thanks where would that be located?
CTScottThread starterUSA, CT · May 26, 2009#100
Originally Posted by regal ↑
Thanks where would that be located?

In the fuse panel that faces the driver's side floor mat at the bottom left of the dash.