Gosh, the pressure you guys are putting me under is worse than the pressure I already feel!😉
Blitz S/C being installed this Saturday!
178 posts · 95,086 views · page 4 of 4
Replies continued
its worst for us cause we are not there to see the start up :(
I don't know much about fuel injectors but ours are plastic things that just push into the fuel rail and are held in place by the o-ring. As Doc has said, you need to lube these with WD-40 before seating them into the fuel rail. I did not do this and I thought that the injectors went in fine. Apparently not.Originally Posted by mikenacarato ↑:( sorry to hear about it. why didnt the rail sit tight?
Picture not included in this copy
ooh VERY CLOSE now!
I stayed up late, just hoping for an update. Thanks Noogie, I can go sleep now. 👍
I stayed up late, just hoping for an update. Thanks Noogie, I can go sleep now. 👍
Today, I ran the red wire that had been left in the passenger compartment back through the loom and into the engine compartment. This wire and the last yellow wire are soldered onto the small ECU connector harness.
Picture not included in this copy
The covers go back on the ECU harness connectors. I put one of them on backwards so that wasted some time.
HINT: Take as many pictures as you can before you disconnect or tear apart anything. Three days later, it's hard to remember what position it was in when you started.
The two ECU harness connectors are reconnected to the ECU and the ECU is mounted back onto the firewall. Wire loom sections are cut to cover as much bare wire as possible.
Picture not included in this copy
The +12V wire is connected to the battery. We don't tie strap anthing down in case we have to take it apart again.
Picture not included in this copy
We shine two lights into the engine compartment for five minutes to make sure there are no tools left in there or connectors left unconnected. My brother finds a bracket that had not been re-attached to the throttle body so I attached it.
The fuel pump connector goes back onto the top of the fuel tank back where the 60% seat was. We prime the fuel system per the directions. Position the fire extinguishers within reach.
The S/C control is set to OFF and the car is started. The car starts and all looks and feels good. We start and stop it a few times to make sure the belt is running straight.
Then with the S/C control set to the lowest level, I start the car again and press the throttle part way. We hear the blower clutch engage. I left my Scangauge at home so I don't know what RPM I was at.
A few more presses of the throttle and the car starts to idle roughly. The CEL comes on and the car does not want to idle very well.
I press the throttle part way again and that is when the injector pops out of the fuel rail. There's gas all over that area and we decide not to do anymore testing until tomorrow.
You can just see the fuel injector and it is now partially out of the fuel rail.
Picture not included in this copy
Picture not included in this copy
The covers go back on the ECU harness connectors. I put one of them on backwards so that wasted some time.
HINT: Take as many pictures as you can before you disconnect or tear apart anything. Three days later, it's hard to remember what position it was in when you started.
The two ECU harness connectors are reconnected to the ECU and the ECU is mounted back onto the firewall. Wire loom sections are cut to cover as much bare wire as possible.
Picture not included in this copy
The +12V wire is connected to the battery. We don't tie strap anthing down in case we have to take it apart again.
Picture not included in this copy
We shine two lights into the engine compartment for five minutes to make sure there are no tools left in there or connectors left unconnected. My brother finds a bracket that had not been re-attached to the throttle body so I attached it.
The fuel pump connector goes back onto the top of the fuel tank back where the 60% seat was. We prime the fuel system per the directions. Position the fire extinguishers within reach.
The S/C control is set to OFF and the car is started. The car starts and all looks and feels good. We start and stop it a few times to make sure the belt is running straight.
Then with the S/C control set to the lowest level, I start the car again and press the throttle part way. We hear the blower clutch engage. I left my Scangauge at home so I don't know what RPM I was at.
A few more presses of the throttle and the car starts to idle roughly. The CEL comes on and the car does not want to idle very well.
I press the throttle part way again and that is when the injector pops out of the fuel rail. There's gas all over that area and we decide not to do anymore testing until tomorrow.
You can just see the fuel injector and it is now partially out of the fuel rail.
Picture not included in this copy
At this point, I doubt that I will take too many more pictures unless something extraordinary happens that need recording. I will continue to post on my progress until it is running and I feel that it is safe enough for me to drive this car home. Eventually, I will make that video for PETERPOOP. You'll probably see me just crawling at walking speed in the parking lot while my brother walks alongside shooting the video.😆 I'll try to hide the fear of a breakdown from my face.😲
I want to thank, in advance, all of you who have been watching this journey for your moral support. I am constantly amazed at how many views this thread has generated.
Special thanks go to those who did the installation before me and have given me many priceless hints.
I hope that this will prove useful to those who have yet to install their Blitz superchargers. Kurokuma-kun, if you are still watching stealthily, good luck this coming week. Same to you whooppee777.
I want to thank, in advance, all of you who have been watching this journey for your moral support. I am constantly amazed at how many views this thread has generated.
Special thanks go to those who did the installation before me and have given me many priceless hints.
I hope that this will prove useful to those who have yet to install their Blitz superchargers. Kurokuma-kun, if you are still watching stealthily, good luck this coming week. Same to you whooppee777.
How long was it before you felt comfortable driving on the freeway? 15 minutes later? A day later?Originally Posted by camelll ↑It is scary to fire the thing up for the first time. I went and got a neighbor to watch in the engine compartment and have a hold of the fire extinguisher.
continues to take notes.....dont forget spacer b.....duct tape the injectors to the fuel rail
Hahhahah... I drove around the block only a few times, and got it out on the freeway about 10 minutes later. Popped the hood just before that to make sure the belt was still good, and there wasn't any weird smells or smoke in the engine bay.
But yeah, for those injectors, we totally thought we had them on fully... pressed and pressed and wiggled and pressed, but still as soon as I started the car, *squirt squirt* all over. You guys are much more safety conscious than I... even though I had an extinguisher in the garage, it definitely wasn't nearby just-in-case!! 😲
Pop that sucker back on, and go make some boost! 😁
But yeah, for those injectors, we totally thought we had them on fully... pressed and pressed and wiggled and pressed, but still as soon as I started the car, *squirt squirt* all over. You guys are much more safety conscious than I... even though I had an extinguisher in the garage, it definitely wasn't nearby just-in-case!! 😲
Pop that sucker back on, and go make some boost! 😁
So, when the belt broke, did that strand you? Did you have to be towed home?Originally Posted by camelll ↑The next problem I had which was a few weeks later was I blew a belt.
Putting the belt on is not the easiest thing, at least for my length of belt.
😆 You may be the one person who gets it done in a day and have time to drive the supercharged Yaris to the movies the same night!Originally Posted by whooppee777 ↑continues to take notes.....dont forget spacer b.....duct tape the injectors to the fuel rail
nice progress! can't wait for videos!!!! oh yah!
Don't use WD40, use vaseline. Also inspect the o rings very carefully. If you cut one you will need a new one, and the car will never run right. The o rings are made of a different material so they arent broken down by contact with gasoline.Originally Posted by LtNoogie ↑I don't know much about fuel injectors but ours are plastic things that just push into the fuel rail and are held in place by the o-ring. As Doc has said, you need to lube these with WD-40 before seating them into the fuel rail. I did not do this and I thought that the injectors went in fine. Apparently not.
Uh oh... really? Maybe this is why I'm having trouble starting my car after it's been sitting for a day. I've figured out that I'm having my fuel pressure bleed off. If I turn the key to "ON" and wait about 5 seconds before cranking, it starts up fine... but if not, it just cranks for a couple seconds, sputters and dies. Then starts fine after that. Hmmmmmm... maybe I need to re-examine my O-rings and replace them.Originally Posted by largeorangefont ↑Don't use WD40, use vaseline. Also inspect the o rings very carefully. If you cut one you will need a new one, and the car will never run right. The o rings are made of a different material so they arent broken down by contact with gasoline.
I didn't... I thought of that after I bought the 6-rib belt and cut it up. I think it's part #4080660.Originally Posted by camelll ↑... Doc Zaius used a 8 rib belt and got 2 for the price of one but I don't remember the part number.
I used the 8-rib because that's all they had and I thought that Doc had used the 8-rib. Ahh, the blind leading the clueless.
Nope... I came up with the genius idea, but a little too late!
I found the problem! It was a rubber injector vibration insulator that had popped out and fell on the floor when we removed the fuel rail. My brother had found it on the floor when we pushed the car back but he did not know what it was.
This rubber insulator pushes against the injector and keeps it seated in the fuel rail. With the insulator out, injector #2 had nothing holding it in tightly against the fuel rail
I followed the shop manual and removed the valve cover 😲 to totally remove the fuel rail and work the injectors. Cool pictures to follow tonight.
I'm going to put everything back together but need to wait for my brother to get here before I fire her up again.
This rubber insulator pushes against the injector and keeps it seated in the fuel rail. With the insulator out, injector #2 had nothing holding it in tightly against the fuel rail
I followed the shop manual and removed the valve cover 😲 to totally remove the fuel rail and work the injectors. Cool pictures to follow tonight.
I'm going to put everything back together but need to wait for my brother to get here before I fire her up again.
So close!! Great work!
Ladies and Gentlemen...WE'VE GOT BOOST!
😁 | 👍 | 🤘
😁 | 👍 | 🤘
woohooo!
Last time, we saw that fuel injector #2 had popped out of the fuel rail and gas was squirting onto the engine. Today, I undid some tie straps and proceeded to loosen the two bolts that hold the fuel rail to the head.
Picture not included in this copy
This allows the fuel rail to pivot up a little and I can pull injectors #1 and #2 completely out of the rail. The other two injectors are too hard to pull out right now because of the angle of the rail.
Picture not included in this copy
There is no good reason why the injector should have popped out of the fuel rail so I looked into the holes where the injectors plug into the head. I noticed that cylinder #1 has a black rubber something in the hole and cylinder #2 has shiny metal.
Picture not included in this copy
Apparently when we pulled the fuel rail the very first time, one of the rubber fuel injector vibration insulators had popped loose and had gotten lost. This is terrible because I'd have to go to Toyota to get a replacement and there's a 100% probability that they would have to order it.
Then, I look on our work bench and I see a black rubber thingy that looks alot like what should have been in the fuel injection port. Luckily for me, when it fell out days ago, it fell onto the floor underneath the car. When my brother pushed the car near the garage door, he found the thing and put it on the bench, not knowing what the heck it was!
Picture not included in this copy
In order to get the other injectors out, I decided to follow the instructions in the shop manual. This is the Yaris shop manual that Violin had posted in 2006 to the DYI forum. That set of manuals is priceless and I suggest that everybody download the pdf files to your computers.
The manual says that in order to work on the fuel injectors, you have to remove the valve cover so the ignition coils come off, the valve cover comes off and I'm staring at the two cams, the timing chain and other cool engine components. This only took 20 minutes.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Now, it's really easy to lift the fuel rail up and I can get to the other two fuel injectors. I put o-ring lube on each injector o-ring and the injectors go back into the fuel rail.
Picture not included in this copy
Picture not included in this copy
The fuel rail slips back into its original position and I make sure the inectors are pushed into the rubber insulators in the head.
Picture not included in this copy
I install everything in the reverse order that they were disassembled and the engine is back in one piece again.
My brother comes to the shop and we go through the startup procedure again but this time the car is idling very smoothly. No CEL. I need to get a wideband A/F gauge badly because it smells like its running rich but it could be because it's still cold.
Lastly, we take it out on the street in this industrial park and test it and I can definitely feel it when the blower kicks in. There's an urgency to get somewhere that I have not felt in this car before.
We'll drive it carefully over this Thanksgiving weekend and I'll keep checking for loose nuts and bolts and I'll check the belt.
Other than that, this project is essentially over. I'll post some driving impressions after I get some more time on it.
Th th th th that's all folks!👍
Picture not included in this copy
This allows the fuel rail to pivot up a little and I can pull injectors #1 and #2 completely out of the rail. The other two injectors are too hard to pull out right now because of the angle of the rail.
Picture not included in this copy
There is no good reason why the injector should have popped out of the fuel rail so I looked into the holes where the injectors plug into the head. I noticed that cylinder #1 has a black rubber something in the hole and cylinder #2 has shiny metal.
Picture not included in this copy
Apparently when we pulled the fuel rail the very first time, one of the rubber fuel injector vibration insulators had popped loose and had gotten lost. This is terrible because I'd have to go to Toyota to get a replacement and there's a 100% probability that they would have to order it.
Then, I look on our work bench and I see a black rubber thingy that looks alot like what should have been in the fuel injection port. Luckily for me, when it fell out days ago, it fell onto the floor underneath the car. When my brother pushed the car near the garage door, he found the thing and put it on the bench, not knowing what the heck it was!
Picture not included in this copy
In order to get the other injectors out, I decided to follow the instructions in the shop manual. This is the Yaris shop manual that Violin had posted in 2006 to the DYI forum. That set of manuals is priceless and I suggest that everybody download the pdf files to your computers.
The manual says that in order to work on the fuel injectors, you have to remove the valve cover so the ignition coils come off, the valve cover comes off and I'm staring at the two cams, the timing chain and other cool engine components. This only took 20 minutes.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Now, it's really easy to lift the fuel rail up and I can get to the other two fuel injectors. I put o-ring lube on each injector o-ring and the injectors go back into the fuel rail.
Picture not included in this copy
Picture not included in this copy
The fuel rail slips back into its original position and I make sure the inectors are pushed into the rubber insulators in the head.
Picture not included in this copy
I install everything in the reverse order that they were disassembled and the engine is back in one piece again.
My brother comes to the shop and we go through the startup procedure again but this time the car is idling very smoothly. No CEL. I need to get a wideband A/F gauge badly because it smells like its running rich but it could be because it's still cold.
Lastly, we take it out on the street in this industrial park and test it and I can definitely feel it when the blower kicks in. There's an urgency to get somewhere that I have not felt in this car before.
We'll drive it carefully over this Thanksgiving weekend and I'll keep checking for loose nuts and bolts and I'll check the belt.
Other than that, this project is essentially over. I'll post some driving impressions after I get some more time on it.
Th th th th that's all folks!👍
please stop saying this!😁Originally Posted by LtNoogie ↑...I fire her up again.
can't wait to see it in person and maybe ride on it!
wow....Noogie, you are a CHAMPION. 👏 🙇
Well done. 👏 Just need to get it on a dyno when you have it 100% finished. 👍
Are you local to the San Fernando Valley?Originally Posted by Malaya1221 ↑please stop saying this!😁
can't wait to see it in person and maybe ride on it!
Thanks to you and your finessing the A/C line! I need to know if you have a jpg or gif of the MicroImage logo. Would you mind if I have it etched on the engine cover?Originally Posted by cali yaris ↑wow....Noogie, you are a CHAMPION. 👏 🙇
I have to take the mental step of going WOT.😲 I want to enjoy a couple of weeks of driving while I continue to tighten nuts and bolts. But, dyno day will come for sure.Originally Posted by *MAD DOG* ↑Well done. 👏 Just need to get it on a dyno when you have it 100% finished. 👍
Taking the valve cover off was a piece of cake becaus there is nothing in the way. There is a rubber gasket ring that fits into a groove in the valve cover. I should have gotten a new gasket and may do so in the near future.Originally Posted by camelll ↑Congrats on the install again. That is some major surgery to get the rail off, I don't know if I would have went that far. Was there a gasket on the valve cover? I am assuming there was, but did you reuse it or put another one on?
I am curious if you are still running the TRD intake?
I am still using the TRD intake but will switch to the AEM intake when Garm and I can hook up. I also will order some gauges from him... wideband A/F, vacuum/boost, ???.
yup local, i'm there almost every week! still have families there in the valley, but i live in torrance, ca now!Originally Posted by LtNoogie ↑Are you local to the San Fernando Valley?
you might want to check this thing out on december 11!
Los Angeles, Ca Meet December 11!!!
whoa. Four years, it's a record! 🙇
Picture not included in this copy
Picture not included in this copy
I'll do some searches. Not better, Long's was really good -- but just by other members doing installs.