Replies continued
LtNoogieThread starterWest Hills, CA · Nov 18, 2008#51First picture is of the alternator after installing it for the Nth time. The pulleys line up parallel and no Spacer B was needed on this car.
Picture not included in this copy
The new intake manifold is bolted to the compressor.😁
Picture not included in this copy
The fuel rail comes off with no problems and no gasoline squirting.
Picture not included in this copy
We tried fit checking the manifold/blower onto the head but encountered interference at this round sensor thing.
Picture not included in this copy
It turns out that Blitz left too much material when they cast the intake manifold and it was hitting the sensor thing. The blue line shows the aluminum that goes beyond the manifold gasket.
Picture not included in this copy
Nothing that a good filing can't take care of!
Picture not included in this copy
This is after filing off the excess aluminum. My younger brother is smarter and braver than I am when it comes to cars.
Picture not included in this copy
We find that we are hitting the alternator when trying to install the manifold/blower. The new alternator bracket was installed wrong! After moving the new alternator bracket, there is no more interference from that area.
Picture not included in this copy
The new alternator position is so close to one of the metal air conditioning lines that I am going to wear a hole in it and lose all my freon. I need to put a rubber hose or something on that metal line to protect it from the alternator. When the engine is rev'd, the torque will pitch the engine forward and the alternator will hit the metal air conditioning line.
Picture not included in this copy
Ok, one last look over before the manifold/blower goes on. The dipstick tube gets reinstalled 180 out.
Picture not included in this copy
Tada! The manifold/blower is on... almost. We could not get it mounted with the left bottom manifold bolt in-place. It's almost impossible to line up the five holes with the five studs/bolts.
Picture not included in this copy
We have to figure out how to do this. We tried to screw the last manifold bolt on after the manifold was on the head but it would not go. That plus I dropped a socket into the engine compartment so we had to waste 10 minutes fishing it out.
Picture not included in this copy
Lastly, I am short one intake manifold nut so tomorrow is a day off from the install while I go to Toyota to buy a nut and maybe another manifold bolt.
eTiMaGoBangkok, Thailand · Nov 18, 2008#52wow, I must applaud you for the awesome step-by-step installation updates, I think it will really help those who are considering one but not sure exactly what is involved in the installations. So, major kudos 🙂
Can't wait to see this lil beast running!
LtNoogieThread starterWest Hills, CA · Nov 18, 2008#53Got it. Thanks! We were contemplating sawing off the bolt to make it shorter and other crazy workarounds. Mike, I almost called you last night but it would have been past 11:00 your time so we mounted and unmounted the manifold/blower three times before calling it quits.
I am still missing one manifold nut so I still have to visit the dealer. So today I give my brother the evening off to play with his 1-month old baby. Hopefully, my sister-in-law won't be as mad.🙂
LtNoogieThread starterWest Hills, CA · Nov 18, 2008#54From some of the previous posts, I'm dreading the wiring more than the mechanical stuff.
Doc ZaiusOttawa, ON, Canada · Nov 18, 2008#55LtNoogie... glad you got the alternator on the right hole. The one you had it in before (and the one just next to it) get attached to the blower itself.
For your a/c line issue, do what I suggested in my last post... mine was the same way. And yeah, do it now before you get the blower completely mounted and there's no room. Something to do on your day off.
And that sensor post thing on the left side of the engine block (where it was hitting the manifold)... I totally don't remember that thing on my setup. Is that new for 2008?
And finally electrical... I was most concerned about that too... procrastinated on it the most. But honestly, once you get the ECU off the firewall, some of the wiring loom cut away to expose the wires, and the little covers off the wiring harness sockets (so you can see which wire goes into which pin), it goes pretty quickly... doing the first crimp is scary... after that, it's quick. Just make sure you don't get your wires all tangled up like I did, and make sure the new connectors you buy are decent and support 18-20ga wire (the ones coming from the activation switch are pretty damn small!)
That's it for now. Keep those pics and posts coming! 😁
LtNoogieThread starterWest Hills, CA · Nov 18, 2008#56Doc, thanks for the tips.
How's the car driving? We haven't heard much about it other than you said it goes "wahhh".
LtNoogieThread starterWest Hills, CA · Nov 18, 2008#57 Originally Posted by
Doc Zaius ↑ And finally electrical... I was most concerned about that too... procrastinated on it the most. But honestly, once you get the ECU off the firewall, some of the wiring loom cut away to expose the wires, and the little covers off the wiring harness sockets (so you can see which wire goes into which pin), it goes pretty quickly... doing the first crimp is scary... after that, it's quick. Just make sure you don't get your wires all tangled up like I did, and make sure the new connectors you buy are decent and support 18-20ga wire (the ones coming from the activation switch are pretty damn small!)
Wow, now you've made it sound real scary. I'm going back to stock.
Doc ZaiusOttawa, ON, Canada · Nov 19, 2008#58Don't be scared! Just take your time and double-check things. And yeah, a 2nd pair of hands is almost required for most of this install!
Originally Posted by
LtNoogie ↑ How's the car driving? We haven't heard much about it other than you said it goes "wahhh".
Well, the car is driving great. I keep the switch (which I still haven't installed yet) set to "high". That way, the power comes on nice and smooth. For a while it was set to "medium", and you'd get that huge jerk of power when it switched on. Not smooth. I'm thinking I might leave it turned off for the winter... don't really need boosted performance in the snow. Plus, I could run regular gas too.
But yeah, the only big issue that I'm a concerned about right now is that with the cold weather, the car is getting
really hard to start. I mean, I used to just twist the key, start would crank maybe twice, and it would go. In the winter, it was sometimes 3-4 times. Now (we're still only in November!) and the car cranks for about 3 seconds before it catches!! I'm wondering if I'm losing fuel pressure somewhere and the fuel rail has to re-pressurize? Or if it's the fact that there's extra stuff on the accessory belt (although, it should be free-spinning when I'm starting).
Anybody else with the Blitz having engine starting problems now that it's getting colder? I'm really concerned that the car is not going to start at all once it's actually COLD.
LtNoogieThread starterWest Hills, CA · Nov 19, 2008#59 Originally Posted by
Doc Zaius ↑ and you'd get that huge jerk of power when it switched on.
I cannot wait to feel that!🤤
Originally Posted by camelll ↑
My car has always been slow to start during winter. I have not had any trouble starting it yet this year, but the low temps have only been down in the 30's.
Cold, as defined here in Southern California, is around 45. Any colder than that, I switch to the Jeep and I put it in 4-wheel drive mode.😆
SIPNGASSoutheast Wisconsin · Nov 19, 2008#60Spoiled California people! 🤣
It was 20 when I went to work this morning...🙄
LtNoogieThread starterWest Hills, CA · Nov 19, 2008#61Not spoiled. Delicate.
staypuftchicago · Nov 19, 2008#62 Originally Posted by
Doc Zaius ↑ Don't be scared! Just take your time and double-check things. And yeah, a 2nd pair of hands is almost required for most of this install!
Well, the car is driving great. I keep the switch (which I still haven't installed yet) set to "high". That way, the power comes on nice and smooth. For a while it was set to "medium", and you'd get that huge jerk of power when it switched on. Not smooth. I'm thinking I might leave it turned off for the winter... don't really need boosted performance in the snow. Plus, I could run regular gas too.
But yeah, the only big issue that I'm a concerned about right now is that with the cold weather, the car is getting really hard to start. I mean, I used to just twist the key, start would crank maybe twice, and it would go. In the winter, it was sometimes 3-4 times. Now (we're still only in November!) and the car cranks for about 3 seconds before it catches!! I'm wondering if I'm losing fuel pressure somewhere and the fuel rail has to re-pressurize? Or if it's the fact that there's extra stuff on the accessory belt (although, it should be free-spinning when I'm starting).
Anybody else with the Blitz having engine starting problems now that it's getting colder? I'm really concerned that the car is not going to start at all once it's actually COLD.
i leave mine on medium, and it is possible to get it smooth, it all depends on how you put pressure on the pedal, i had no problems starting her up in the cold so far, but its only been in the 30's, i installed the new perrin catch can and it doesnt get hot whatsoever as the greddy can does. and runs smoother imo with it installed, maybe camelll can chime in on this. i guess it doesnt help that we
have to change to colder plugs either
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#63Tonight started out Ok but spiraled downhill until it became a disaster. Pictures will posted shortly.🙁
PETERPOOPOahu · Nov 20, 2008#64are you lying
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#65The manifold/blower slips onto the three studs, thanks to Camell for the tip. The two outside Torx tip bolts are replaced with the hex head bolts.
Picture not included in this copy
Picture not included in this copy
The fuel rail gets wiggled loose until the injectors can be popped out to make room to install and tighten the top manifold nuts. Gasoline drips onto the valve cover and we breathe fumes for the next half hour.
The injectors are lying willy-nilly.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
DO NOT TIGHTEN THE MANIFOLD NUTS AND BOLTS YET!
There are two bolts that need to attach the pulley side of the blower to the alternator bracket. I did not take a picture so here is one from the installation manual.
Picture not included in this copy
Since I had already tightened the five manifold nuts and bolts (f**k-up #1), there was no way for the other bolts to line up. BTW, we could not find those two bolts in the packages. Luckily, last night I bought a box of metric hardware at Pep Boys for $9.99. That came in very handy.
We install two bolts from the opposite side as the instructions said to kinda work their way and line up the holes.
Picture not included in this copy
I start cranking away at one of the bolts, not paying attention. (f**k-up #2). Instead of causing the alternator bracket to line up, the bolt pushes the top of the alternator bracket to towards the fender. I've bent the damn thing and the alternator is now crooked!😲
I don't have a picture of the messed up situation. We carefully send the second bolt through the second hole and miraculously, it makes it through both holes. I attach a nut and start tightening which pulles the alternator bracket back in line. The Moron dodges a bullet.
The picture shows the alternator bracket firmly attached to blower and there is no gap. Earlier, there was a 1/4 inch gap which was all alternator bracket being bent towards the fender.
Picture not included in this copy
Ok, back when I attached the blower to the intake manifold, I did not pay attention to the hint below so now I have no place to attach my dipstick tube bracket. My brother will fab something for the dipstick tube to attach to so that it doesn't pop out and fall off. (f**k-up #3 but done earlier)
Picture not included in this copy
Picture not included in this copy
The compressor inlet pipe goes on and it nows looks like a supercharger! Time to attach the vacuum lines to the inlet pipe.
Picture not included in this copy
I think others have mentioned it but one of the original vacuum lines is too short to go to its inlet pipe nipple. First picture show the vacuum line before the teardown. Second picture shows where it needs to go.
Picture not included in this copy
Picture not included in this copy
So close to attaching the throttle body and the CAI! Now I have to go to Pep Boys tomorrow to buy some vacuum line.😠
Since we can't close her up, we start to route the belt through the maze of pulleys. It's now really tight in that area and it takes two of use to snake through its path.
DISASTER! The metal A/C lines that we were afraid of before get in the way of the belt! I think Doc had problems with his A/C lines too.
Picture not included in this copy
The only thing we can figure out is to try to reach into the impossibly tight spaces to remove a screw holding a bracket that holds the A/C line. We might be able to yank the lines out of the way and tie them down somehow with nylon straps.
While backing out one of the screws, I realize that the screw is very long and now I can't get my ratcheting box end wrench off the head because I am too close to the NST water pump pulley. It's one of those ratchets that you have to turn around to tighten, so any movement I make keeps backing out the screw. I now have a freaking tool stuck down there. I did not know whether to laugh or to cry.
Picture not included in this copy
My brother will try to buy some big ass needle nose pliers tomorrow to try to turn the srew back in until the wrench can come free. If that doesn't work, he may have to run a hacksaw blade down there and hope to cut the screw. Did I mention it is really tight down there?
We have no idea what to do next because you cannot get your hand in there. Tomorrow's another day.
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#66 Originally Posted by camelll ↑
That is what I thought........... Until that damn second B spacer. It is alot easier the second time as you know what to expect and have all the tools.
I cannot imagine what it was like taking it apart and putting it together a second time just for that Spacer B but I know that there was no other way for you. You should advertise yourself as a qualified Blitz installer in the Midwest.👍
The mechanics around here wanted $950 to do the install. That almost sounds cheap by now.
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#67kurokoma-kun and whooppee777, are you guys taking notes?
Your turns are coming up next and I don't want to have come out there to get you out of trouble. Especially if you repeat the same f**k-up I did.
🙂
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#681,369 views so far! I am grateful that there is so much interest.
It must be like watching a train wreck in slow motion. LOL
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#69It's funny how you and I can laugh about stuff like the non-existent fuel pump relay now that it's past us. That was the first day and the first step of the install and I'm saying to myself WTF!
I think all the views are from the same 10 people. 5 of them going 😲 ... "I'm not doing a supercharger". The other 5 like yourself going "oh yeah, I forgot about that nighmarish step. Good times." 😁
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#70 Originally Posted by camelll ↑
No problem. How did that center nut tighten up? That thing gave me a massive headache until I went out and bought a ratcheting swivel box end wrench.
I used an open-end wrench. The head of the ratching box end was too big. The nut tightened up as easily as the other two on top.
Originally Posted by camelll ↑
I did not put those bolts in, I did the same thing and when I got done I realized that I missed that step. I tried but the holes did not line up. I figured that the alternator bracket and the compressor are both attached to the engine block and move together anyways and there is no gap in mine either. I might buy some smaller bolts someday and do what you did, but I am not having any problems after I put that second B spacer in.
I am guessing that those bolts keep the top of the alternator bracket from vibrating from side to side. Bolting it to the rigidly mounted blower makes sure that you don't get that movement. Anyhow, I have one bolt in there now. The second hole is stripped and we could not start a tap through it.
Originally Posted by camelll ↑
That sucks, I did not have as much trouble with my ac lines, I just pushed mine out of the way and that was that, maybe the sedan has a little more room in the engine compartment.
A/C lines are gonna kill me in the end.
PETERPOOPOahu · Nov 20, 2008#71stay strong
cali yarisCanoga Park, CA · Nov 20, 2008#72well, it may read like mostly bad news to some, and mostly good news to others, because you got it done and you're closer to finishing.
So far, you've resolved every problem you encountered, so I have faith in the big finish!
I'm taking you out for a nice sushi dinner when you're done -- you can drive, or course. 😁
Doc ZaiusOttawa, ON, Canada · Nov 20, 2008#73 Originally Posted by
LtNoogie ↑ I used an open-end wrench. The head of the ratching box end was too big. The nut tightened up as easily as the other two on top.
Are you serious?! Wow... lucky guy! I ended up getting my girlfriend (with small hands) to get that nut on the bolt, and get the threading started.
Originally Posted by
LtNoogie ↑ A/C lines are gonna kill me in the end.
What'd I tell you, man? Getting in there now to fix the A/C lines is gonna be wicked hard.
But yeah, this has been like a trip down memory lane. I remember about the dipstick bracket... I managed to get a shorty 14mm (I think?) wrench under there and loosen it up so I could attach it. Bummer about bending the bracket... I'm glad it straightened out! And remember to put a little lubricating fluid on the O-rings when you pop the rail back on the injectors. My friendly neighbourhood Toyota tech told me to always use something when fiddling with the injectors, otherwise the rings might pinch and not seal properly.
Agreeing with camelll, it's definitely not as hard to undo and redo the 2nd time. For your A/C lines (and those two bolts) (AND the dipstick), it might be easier to take the 'charger back off, fix everything, and then put it back on. Seriously. I know it sucks! 😢 But those lines are really in the way!
And for the ECU, it's only held to the firewall by three 10mm nuts & bolts... getting it off is pretty easy. The two big connectors on top of it, the left one (the bigger) won't clear the cowling... so either you take off the whole cowling like camelll did, or pop the ECU off the firewall, undo the connectors, and put the ECU on a table while you do your splicing. Either way...
We all had our struggles putting this thing on. I didn't tighten my stud bolts on the 'charger as much as I wanted, and then ended up stripping a nut (so I'll never get it off). Keep going! Good luck!!
Oh, and thanks for the responses guys about your cars starting fine in the cold weather. It's been happening here even when it's only in the 40s. So maybe I did something wrong. I'll have to pop the hood and have my girlfriend start it while I try to see if everything is ok. Hmmmm!
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#74 Originally Posted by
cali yaris ↑ I'm taking you out for a nice sushi dinner when you're done -- you can drive, or course. 😁
No, YOU can drive. I'll be behind you in MY car as you tow it with my shiny new tow hook.🙂
Nexus1155Dorchester · Nov 20, 2008#75 I'll be behind you in MY car as you tow it with my shiny new tow hook
A yaris towing a yaris, that will be a hoot to see...the car explode from its insides out! :P
cali yarisCanoga Park, CA · Nov 20, 2008#76hmmm, this could be arranged 😁
LtNoogieThread starterWest Hills, CA · Nov 20, 2008#77 Originally Posted by
Nexus1155 ↑ A yaris towing a yaris, that will be a hoot to see...the car explode from its insides out! :P
I would pick up the parts that dropped out of his car and try to re-sell them on here.🙂
Nexus1155Dorchester · Nov 20, 2008#78hahah you and me both, but everyone is in Cali for some reason... got to bring this extravaganza down here
LtNoogieThread starterWest Hills, CA · Nov 21, 2008#79Tonight we took it kinda easy. I still had the combination wrench stuck on a bolt from last night. My brother went to Harbor Freight to buy some really long locking pliers and a magnetic picker upper while I went to Pep Boys to buy a two-foot gripper. I also picked up one foot of vacuum hose.
Picture not included in this copy
We were able to free the tool and eventually get the screw completely out of the very tight space.👍
We are still having problems with the interference that the metal A/C lines are causing with the new belt. There's a compression fitting block which is so close to the belt that the belt will tear itself apart on it when the engine rocks front to rear.
We spent an hour pulling and pushing on the entire A/C line but could not get it to move very far from the belt path. At this time, I am willing to find an auto air conditioning shop to see if they can replace the metal lines with flexible lines and reroute them away from the pulleys and the belt. Tomorrow I'll see if my mechanic can recommend someone.
Picture not included in this copy
Since there was very little we could do there, I undid the bolt that held the L bracket between the manifold and the blower. This was done by feel because the L bracket is now underneath and out of site. The new hinged inspection mirror I bought at Pep Boys was useful here.
Picture not included in this copy
With the bolt removed, I was able to install the dipstick tube support bracket and then bolt that bracket to the one attached to the dipstick tube. Yeah!!! One minor victory.🙂
It would have been much easier to have installed the dipstick tube support bracket when the manifold/blower was still on the bench.
Picture not included in this copy
The vacuum hoses go onto the intake tube easy, now that I have the right length.
The throttle body goes onto the intake tube.
The water hose support goes onto the throttle body.
The CAI attaches to the throttle body and a few more hoses connect to the CAI.
And voila, the roadside of the motor is back together. It looks pretty and ready to run if you ignore the fact that the belt still isn't on.
Here are a few views of the engine bay with the supercharger installed.
Picture not included in this copy
Isn't that purdy?
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The supercharger sits so high that the stock engine cover will not fit anymore. We will have to cut the engine cover so that it will fit flat on top of the valve cover. There are only two studs where I can fasten it down with the original nuts.
Picture not included in this copy
Here is a before shot for comparison. There used to be four studs that held the engine cover down.
Picture not included in this copy
See how much clearance there is between the altenator pulley and the A/C lines when the alternator is in its stock position. Once you flip it upside down and move it lower, that's when you get into trouble. Make sure you move all your A/C lines right after you removed the alternator while you still have plenty of room to work. Loosen the screw on the clamp and the A/C line will slide around when you push or pull on it.
I don't know when we will do the electrical installation. I really need to take care of the A/C line interference first so I can install the belt.
It certainly looks the the supercharger pictures that others have posted but it's not running yet. Perhaps by Monday.
Malaya1221Torrance, Ca · Nov 21, 2008#80forget the engine cover....the blower looks sexy, great job and have fun!👍
LtNoogieThread starterWest Hills, CA · Nov 21, 2008#81Thanks, Malaya. Someone said that the engine cover prevents the heat from the engine from discoloring your hood right overhead that spot.
staypuftchicago · Nov 21, 2008#82 Originally Posted by camelll ↑
I am certain either the 07's or the sedan has more room in the engine bay.
This could be very important info LTNOOGIE: I don't know if this true or not but I was warned by yarisdarkness not to use the TRD CAI with the blitz as it has a bypass valve that can be sucked in! I did not know that you had the trd till the last set pics you just posted. Maybe garm can contact blitz to verify this information. Yarisdarkness is a authorized blitz dealer so I would think this info is very accurate.
i thought i read somewhere that 2 pc intakes are not recommended for this application. hey mike good thing we got the single piece fujita cai.
i'll take a pic of my a/c line near the compressor and see what went wrong.
cali yarisCanoga Park, CA · Nov 21, 2008#83As soon as I saw the CAI I also questoned it. I will also try to get an answer about that for you today.
LtNoogieThread starterWest Hills, CA · Nov 21, 2008#84 Originally Posted by camelll ↑
This could be very important info LTNOOGIE: I don't know if this true or not but I was warned by yarisdarkness not to use the TRD CAI with the blitz as it has a bypass valve that can be sucked in! I did not know that you had the trd till the last set pics you just posted. Maybe garm can contact blitz to verify this information. Yarisdarkness is a authorized blitz dealer so I would think this info is very accurate.
Wow, ok. I know that Garm checks this thread. I still have my stock airbox but I may have to switch to a one-piece CAI like you guys.
Anyone else with authoratative info on this?
LtNoogieThread starterWest Hills, CA · Nov 21, 2008#85Garm dropped by today to look at the S/C project. While I was explaining how I was having new A/C lines fabbed to clear the belt, he reached in and yanked the A/C line out of the way.😲
I should have had my Wheaties that day.🙁
Number one: I've already admitted to being a moron in an earlier post.
Number two: We were trying to pull the line forward. He pulled it sideways.
I owe him a sushi lunch.
cali yarisCanoga Park, CA · Nov 21, 2008#86aw shucks... :flex:
LtNoogieThread starterWest Hills, CA · Nov 21, 2008#87Garm, can you do the electrical for me?🙄
LtNoogieThread starterWest Hills, CA · Nov 21, 2008#88My brother wants the night off so no updates tonight. Thanks for checking in.
cali yarisCanoga Park, CA · Nov 21, 2008#89I'm better at beating stuff up than finessing wires. Sorry!
No updates tonight? What am I supposed to do instead of watch this thread?
No No No !!
LtNoogieThread starterWest Hills, CA · Nov 22, 2008#90Did you guys find the belt to be too long or too short? We got the belt on and the tensioner went to the bottom of the slot. I'm going to get a shorter belt.
SIPNGASSoutheast Wisconsin · Nov 22, 2008#91I love this thread.😁
whooppee777Maryland · Nov 22, 2008#92how long till the wiring is done?
PETERPOOPOahu · Nov 22, 2008#93i think i read that the belt was too long on other installs, but i swear cali yaris said the new kits come with a belt that fits? don't quote me.
LtNoogieThread starterWest Hills, CA · Nov 22, 2008#94Now that I know how to read the numbers on belts, my kit came with a 4-rib 69" belt. We went to three auto parts stores before we found an 8-rib 66" belt. We're about to start splitting it into two 4-rib belts.
I should have read Doc's and Camell's posts closer.
LtNoogieThread starterWest Hills, CA · Nov 22, 2008#95Belt is on. ECU is off. Studying the ECU harness to make sure we do this right.
LtNoogieThread starterWest Hills, CA · Nov 22, 2008#96Before I start on the ECU wiring, I need some advice on the wiring from those who have done it. My brother says that crimping is bad and he prefers to cut wire, solder, and shrink wrap.
Is this where Doc and EchoHrs had much of their problems?
cali yarisCanoga Park, CA · Nov 22, 2008#97cut/wire/solder and shrink wrap is always superior to crimping. Always.
Dunno about the belt, I was told they were replaced. 🤷
LtNoogieThread starterWest Hills, CA · Nov 22, 2008#98Garm, they kinda told you right.
The kit came with a 1695 mm belt which converts to 66.7 inches which for some reason bottomed out the tensioner.
I bought a 8PK1675 belt, which I split. 1675 mm converts to 65.9 inches. The tensioner is near the top of the bracket but it was tight going to slip it over the tension pulley.
We looked online at
www.upcbelt.com and there is a 4PK1685 which would be ideal. Probably have to buy it online. 1685 mm equals 66.3 inches which should put the tension pulley near the middle. We're splitting hairs now.
LtNoogieThread starterWest Hills, CA · Nov 22, 2008#99Regular life calls and we have to stop for the day. The ladies are impatient to do other stuff.
We will go get a soldering iron and shrink tubing. I expect that we will wrap this up tomorrow morning or Monday night at the latest.
I don't have a bunch of pictures but will post when I get home.
Don't know how I'll handle the the CAI yet but we are close, people!
cali yarisCanoga Park, CA · Nov 22, 2008#100Thank you for the regular updates. You can post pictures of the ladies anytime now, that will hold us over until your next report... 😲