Awe! She's beautiful!
Blitz S/C being installed this Saturday!
178 posts · 95,086 views · page 3 of 4
Replies continued
First picture is of the A/C lines that have been pulled out of the way of the belt. The A/C lines have been temporarily tied to the sheet metal with a nylon strap. We'll get a metal hose clamp to make it more secure.
At this time, we did not know that the belt was too long so it is just laying loose on the S/C pulley in this picture.
Picture not included in this copy
After spending an hour or more looking for the right length fan belt, it finally goes on. You need a 66" belt as others have posted before. The robots at the parts counters will always ask you "What car is this for?" so you have to tell them that is a special application like a racing go-cart. Otherwise they will look up the stock belt for you.
It still took four hands and three attampts to get the belt onto the tensioner pulley.
The grey S/C cable is connected to the valve cover to hold it in place.
Picture not included in this copy
Next, the ECU comes off the firewall. I removed the bracket that holds the big ECU harness to the fender wall.
Picture not included in this copy
The big connector has a shroud at the back of the connector to protect the wires. You first have to cut the tie strap that holds the top of the shroud to the harness. Then a insert a pick or tiny screwdriver blade into the front of the shroud to pop it off.
Picture not included in this copy
This is what the side of the shroud looks like once you take it off. The tab is on the front side edge of the shroud.
Picture not included in this copy
If you do it wrong, the tab breaks off.
Picture not included in this copy
And here is the large harness all ready for you to crimp on the Blitz wires. Instead of crimping, we are going to cut the factory wires and solder them to the Blitz wires and follow with shrink tubing.
Note the bracket mentioned earlier and where it attaches to the fender wall.
Picture not included in this copy
BTW, it really helps to lay out all the electrical harnesses on the floor and read the instructions. Tape the ends of the bare wires with where they are supposed to go and get a good mental picture of the entire setup. This is no place to mess up.
At this time, we did not know that the belt was too long so it is just laying loose on the S/C pulley in this picture.
Picture not included in this copy
After spending an hour or more looking for the right length fan belt, it finally goes on. You need a 66" belt as others have posted before. The robots at the parts counters will always ask you "What car is this for?" so you have to tell them that is a special application like a racing go-cart. Otherwise they will look up the stock belt for you.
It still took four hands and three attampts to get the belt onto the tensioner pulley.
The grey S/C cable is connected to the valve cover to hold it in place.
Picture not included in this copy
Next, the ECU comes off the firewall. I removed the bracket that holds the big ECU harness to the fender wall.
Picture not included in this copy
The big connector has a shroud at the back of the connector to protect the wires. You first have to cut the tie strap that holds the top of the shroud to the harness. Then a insert a pick or tiny screwdriver blade into the front of the shroud to pop it off.
Picture not included in this copy
This is what the side of the shroud looks like once you take it off. The tab is on the front side edge of the shroud.
Picture not included in this copy
If you do it wrong, the tab breaks off.
Picture not included in this copy
And here is the large harness all ready for you to crimp on the Blitz wires. Instead of crimping, we are going to cut the factory wires and solder them to the Blitz wires and follow with shrink tubing.
Note the bracket mentioned earlier and where it attaches to the fender wall.
Picture not included in this copy
BTW, it really helps to lay out all the electrical harnesses on the floor and read the instructions. Tape the ends of the bare wires with where they are supposed to go and get a good mental picture of the entire setup. This is no place to mess up.
The plastic strap you have holding the A/C line out of the way is probably better than a metal clamp. Metal can/will wear through the aluminum line due to prolonged vibration, and the line is probably over $100, plus the A/C recharge. Double up the plastic if it makes you feel better, or if you must use a metal clamp be sure to use some type of rubber padding between them. Just be sure the line is run cleanly, metal on metal is bad...
And good job listening to your brother about the soldering and shrinkwraping, he is telling you the correct way to do it.
And good job listening to your brother about the soldering and shrinkwraping, he is telling you the correct way to do it.
awe! one of my favorite movies!Originally Posted by LtNoogie ↑When Princess Maddie makes a request, I can only answer "As you wish"
I can almost hear Mark Knoppler's music wafting up.
Most of the ladies will understand this. For you guys, this is a guaranteed score if you play this DVD on date night.
I own that movie -- comes in handy. 😉
It really IS a guys romance movie...really...and if a guy can like that movie, he's going to get the girl he's watching it with.Originally Posted by cali yaris ↑I own that movie -- comes in handy. 😉
👍
if a guy can like that movie, he's going to get the girl he's watching it with.duly noted. 😁
I also own it and could watch that movie a million times and never get sick of it.
well this thread is already way off topic, so...
I only recently discovered the Princess Bride... I very often saw the quote "Hello, My name is Inigo Montoya..." but had no idea where it was from 😁 excellent movie, its cult status is certainly not inconceivable! 😆
BTW thinkgeek.com now has a Dread Pirate Roberts articulated action figure 😉
Now, back to your regular supercharger programming!
I only recently discovered the Princess Bride... I very often saw the quote "Hello, My name is Inigo Montoya..." but had no idea where it was from 😁 excellent movie, its cult status is certainly not inconceivable! 😆
BTW thinkgeek.com now has a Dread Pirate Roberts articulated action figure 😉
Now, back to your regular supercharger programming!
Yeah..we did get a bit off-topic, huh?
LT, will you be working on the SC again today? We're all waiting!
LT, will you be working on the SC again today? We're all waiting!
OMG!! Thomas!! I *love* that website!! Did you see the Office Space Kit?? Wow, I know what everyone in my Cubeville is getting from me for Christmas. 🤣FABULOUS!! 👍Originally Posted by eTiMaGo ↑well this thread is already way off topic, so...
I only recently discovered the Princess Bride... I very often saw the quote "Hello, My name is Inigo Montoya..." but had no idea where it was from 😁 excellent movie, its cult status is certainly not inconceivable! 😆
BTW thinkgeek.com now has a Dread Pirate Roberts articulated action figure 😉
Now, back to your regular supercharger programming!
Good luck today!
I might drop by, I promise not to wrestle with your car again... maybe the dog though... 😉
Hey Garm, did you ever get in contact with Blitz to see if the compressor was compatible with the 2 pc CAI's?Originally Posted by cali yaris ↑As soon as I saw the CAI I also questoned it. I will also try to get an answer about that for you today.
Garm, we are leaving the shop (1:10). There are only two wires left to do and there's a conflict with the instructions that I have to ask the guys about that have done the install.Originally Posted by cali yaris ↑I might drop by, I promise not to wrestle with your car again... maybe the dog though... 😉
The S/C Activation Box stays inside the car so I run the loose wires through the wire loom.
Picture not included in this copy
Up on the firewall above and to the left of the ECU was a rubber plug that plugged a hole leading to the interior of the car. I pulled the plug out and from the inside slit a vertical and horizontal opening in the carpet that covers the hole.
I found the perfect gromment at Pep Boys that had a tapered side that pushed easily into the hole. I push the wire loom through that gromment and into the engine compartment.
Picture not included in this copy
There are four wires in the bundle that come from the S/C Activation Box. The instructions say:
"8. Run all the wires, except the red wire from the activation box, to the passenger side glove box area. (Leave the red wire on the driver’s side for now.)"
So we leave the red wire inside the car for now.
The blue wire that comes from the S/C Activation Box has a barrel crimp connector at the end of it, so I thought. There is another identical blue wire that comes off of the relay assembly that feeds through the grommet to go inside the car. The relay assembly stays in the engine compartment.
Picture not included in this copy
When I tried to crimp the blue wire from the engine compartment to the barrel crimp connector from the S/C Activation Box, the wire keeps falling out of the crimp. So, we cut off the crimp connector and solder the two ends of the blue wires together and shrink wrap the new connection.
Picture not included in this copy
Picture not included in this copy
Inside the engine compartment we slowly start snipping wires in the ECU harness, each of us double-checking the other to make sure we are snipping the correct wire. The new wires from the Fuel Control Unit connector harness are soldered one one by one onto the snipped ECU wires and the bundle shrink wrapped.
Picture not included in this copy
Picture not included in this copy
One wire from the Fuel Control Unit connector harness has to be spliced into the blue wire that went from the relay assembly to the interior of the car. We had to cut the blue wire and make a three-way blue wire connection. The third leg goes to the green wire from the Fuel Control Unit connector harness.
Picture not included in this copy
This completes all the wires that goe into the large ECU harness connector. Next, we remove the shroud from the small ECU harness connector by releasing two tabs and cutting the tie strap that ties the back of it to the harness.
Picture not included in this copy
Picture not included in this copy
So there's only one yellow wire from the interior S/C Activation Box to connect to the small ECU connector and one red wire from the Fuel Control Unit connector harness to connect to the small ECU connector.
Picture not included in this copy
But if you notice, there's another red wire from the interior S/C Activation Box that's supposed to also connect to the same red wire that came from the Fuel Control Unit connector harness.
Picture not included in this copy
This is the same red wire the instructions said to leave inside the car so the instructions don't match the wiring diagram.
Those of you who have done this installation, did you route the red wire from inside the car through the firewall and connect as the wiring diagram shows? If that's the case, why did the instructions say to leave the red wire inside the car and not push it through with the rest of the bundle?
Picture not included in this copy
Up on the firewall above and to the left of the ECU was a rubber plug that plugged a hole leading to the interior of the car. I pulled the plug out and from the inside slit a vertical and horizontal opening in the carpet that covers the hole.
I found the perfect gromment at Pep Boys that had a tapered side that pushed easily into the hole. I push the wire loom through that gromment and into the engine compartment.
Picture not included in this copy
There are four wires in the bundle that come from the S/C Activation Box. The instructions say:
"8. Run all the wires, except the red wire from the activation box, to the passenger side glove box area. (Leave the red wire on the driver’s side for now.)"
So we leave the red wire inside the car for now.
The blue wire that comes from the S/C Activation Box has a barrel crimp connector at the end of it, so I thought. There is another identical blue wire that comes off of the relay assembly that feeds through the grommet to go inside the car. The relay assembly stays in the engine compartment.
Picture not included in this copy
When I tried to crimp the blue wire from the engine compartment to the barrel crimp connector from the S/C Activation Box, the wire keeps falling out of the crimp. So, we cut off the crimp connector and solder the two ends of the blue wires together and shrink wrap the new connection.
Picture not included in this copy
Picture not included in this copy
Inside the engine compartment we slowly start snipping wires in the ECU harness, each of us double-checking the other to make sure we are snipping the correct wire. The new wires from the Fuel Control Unit connector harness are soldered one one by one onto the snipped ECU wires and the bundle shrink wrapped.
Picture not included in this copy
Picture not included in this copy
One wire from the Fuel Control Unit connector harness has to be spliced into the blue wire that went from the relay assembly to the interior of the car. We had to cut the blue wire and make a three-way blue wire connection. The third leg goes to the green wire from the Fuel Control Unit connector harness.
Picture not included in this copy
This completes all the wires that goe into the large ECU harness connector. Next, we remove the shroud from the small ECU harness connector by releasing two tabs and cutting the tie strap that ties the back of it to the harness.
Picture not included in this copy
Picture not included in this copy
So there's only one yellow wire from the interior S/C Activation Box to connect to the small ECU connector and one red wire from the Fuel Control Unit connector harness to connect to the small ECU connector.
Picture not included in this copy
But if you notice, there's another red wire from the interior S/C Activation Box that's supposed to also connect to the same red wire that came from the Fuel Control Unit connector harness.
Picture not included in this copy
This is the same red wire the instructions said to leave inside the car so the instructions don't match the wiring diagram.
Those of you who have done this installation, did you route the red wire from inside the car through the firewall and connect as the wiring diagram shows? If that's the case, why did the instructions say to leave the red wire inside the car and not push it through with the rest of the bundle?
Although cutting/soldering/shrink wrapping wired connections makes for more reliable joints, not everyone has all the tools to do the job right. My brother and I come from a defense industry background so we have most of the tools of the trade. This may be harder on a typical college student.
Picture not included in this copy
Picture not included in this copy
Ooooh, bustin out the good soldering equipment...
Is the red wire power (or ignition power)? In which case you could find one inside the car. Test it...
Is the red wire power (or ignition power)? In which case you could find one inside the car. Test it...
Woooh, Noogie, looking at all this wiring and not understanding any of it makes me understand your joke about keeping the car stock! @_@
Hey Noogie! Looking good! Two soldering stations?! If ever any of my crimps fail, I'm totally gonna undo everything and go this route as well.
But to answer your question, I fed the activation switch's red wire back into the engine bay and spliced into the ECU connection mentioned in the installation guide. Others found an IG+ source inside the passenger cabin to splice into (someone used the cigarette lighter as well).
Good use for the wiring loom! Different from me... I used my included loom to wrap the power wire from the battery over to the relay near the 'charger. For the 4 wires going into the cabin, I wrapped them with electrical tape near the grommet, and they're just bundled together inside the car.
Anyhow... again, nice writeup. And get ready... you'll be making boost in less than 24 hours! 😁
But to answer your question, I fed the activation switch's red wire back into the engine bay and spliced into the ECU connection mentioned in the installation guide. Others found an IG+ source inside the passenger cabin to splice into (someone used the cigarette lighter as well).
Good use for the wiring loom! Different from me... I used my included loom to wrap the power wire from the battery over to the relay near the 'charger. For the 4 wires going into the cabin, I wrapped them with electrical tape near the grommet, and they're just bundled together inside the car.
Anyhow... again, nice writeup. And get ready... you'll be making boost in less than 24 hours! 😁
Yeah, where my brother used to work, they were never allowed to strip wires with cutters due the risk of nicking wires. All stripping had to be done by melting the insulation. The HoTweezers is that device.
The soldering iron is a standard adjustable Weller soldering station. The last thing is a heat gun.
You also see a spool of solder, solder wick, a solder sucker, and flux remover. Off camera is a jar of flux. Lastly, there's a bag of assorted sized shrink tubing.
It is tight working in that ECU connector but we learned that you can pull some extra wire length out of the harness to give more wire to work with. It was a bit slow but we wanted it to look like it does at work.
The soldering iron is a standard adjustable Weller soldering station. The last thing is a heat gun.
You also see a spool of solder, solder wick, a solder sucker, and flux remover. Off camera is a jar of flux. Lastly, there's a bag of assorted sized shrink tubing.
It is tight working in that ECU connector but we learned that you can pull some extra wire length out of the harness to give more wire to work with. It was a bit slow but we wanted it to look like it does at work.
It's attention to detail like that, that creates a solid, long-lasting project 🙂
My approach would be to twist wires together and wrap with electrical tape, that's why I don't do wiring 😆
My approach would be to twist wires together and wrap with electrical tape, that's why I don't do wiring 😆
😆Originally Posted by eTiMaGo ↑It's attention to detail like that, that creates a solid, long-lasting project 🙂
My approach would be to twist wires together and wrap with electrical tape, that's why I don't do wiring 😆
Thomas, do NOT do electrical work on your car!
Here's a question for all you Blitz owners: what did you use to cut up your engine cover? I bought a Dremel, and a few bits to cut soft things like plastic & wood. Anyhow, worked ok, but the bit gets hot and starts melting plastic and gets plastic goo everywhere, and is hard to make nice even cuts. What did other people use? Band saw? Hack saw? More patience? Let me know... I'm halfway done, and want it to come out nice! 😁
I'm switching to a custom aluminum cover. I'm going to have it anodized blue and have some lettering etched into it.
We'll tackle that after the car's running.
We'll tackle that after the car's running.
I've been reading your thread, Long!
I love how you're doing this with your brother, with no goofing off whatsoever. Maybe you guys should be an official Blitz s/c installation center!
I love how you're doing this with your brother, with no goofing off whatsoever. Maybe you guys should be an official Blitz s/c installation center!
You know what's kinda sad? We've figured out that we could do another installation in half the time now that we know what we're doing. All that learning curve for one installation.
JR, you need to buy Garm's last Blitz. The three of us can do the installation in one weekend. You just have to buy us tacos from the nearby burrito shop.
JR, you need to buy Garm's last Blitz. The three of us can do the installation in one weekend. You just have to buy us tacos from the nearby burrito shop.
I would buy the s/c if I had that much money, but I don't! 😢
On top of that, finals is in 3 weeks.. then I have to buy more books and units! gahhhhhh!!!
And now my CRX is acting up, I need a new starter 🙄
On top of that, finals is in 3 weeks.. then I have to buy more books and units! gahhhhhh!!!
And now my CRX is acting up, I need a new starter 🙄
Nice Progress
this wiring thing happening here whats the issue exactly. this is the part i was worried about
whooppee, there really hasn't been an issue. We ran out of time but there was only the one red wire that I thought belonged inside the car.Originally Posted by whooppee777 ↑this wiring thing happening here whats the issue exactly. this is the part i was worried about
Doc ran it into the engine compartment. Camell left it inside the car. It connects to Ignition +12V so I have my choice of either.
We really took our time here and have not had a mishap. Yet.
You just need to decide to use the crimps the kit provides or to solder the connections.
well good. now stop screwn around, drop everything ur doing and finish this damn thing. so i can here that this thing fires right up and works on the 2008 LB
No updates tonight.🙁
I'm working late for a presentation tomorrow morning.
I'm working late for a presentation tomorrow morning.
:: paces the room ::
:: taps foot ::
:: considers watching TV instead ::
:: taps foot ::
:: considers watching TV instead ::
Garm, you just want your sushi.
I want so much more than that 😉
Wow!
Everything is closed up. We are going to turn on the ignition now.
oh my! Good luck!!!
and? boom? vroom?
He knows we're waiting, right? =)
I've got a beer and some popcorn, I'm ready
Why is it taking so long? Is he buzzing around the neighborhood?? I hope the silence is a good thing....
4 minutes...I only have 4 minutes left, Long!
4 minutes...I only have 4 minutes left, Long!
This is the first thread I'm checking in the morning!
me too! This is....well.. painful, in a funny sort of way?
kinda like when you were a kid and you got your first remote control car. I never put mine down, did you? He'll update us soon, I'm sure.
👍👎
Ok, the car started. It idled rough but we verified that the belt did not disintegrate.
The blower clutch engages and disengages.
Then 5 minutes into idling, my brother yells "stop the engine!"
Fuel injector #2 popped out of the fuel rail and gas went all over the valve cover.
We will have to do a partial disassembly and try to get the injector to fit tighter.
Ok, the car started. It idled rough but we verified that the belt did not disintegrate.
The blower clutch engages and disengages.
Then 5 minutes into idling, my brother yells "stop the engine!"
Fuel injector #2 popped out of the fuel rail and gas went all over the valve cover.
We will have to do a partial disassembly and try to get the injector to fit tighter.
:( sorry to hear about it. why didnt the rail sit tight?
Believe me, we had two fire extinguishers at the ready. That's all we're gonna do for the night. The engine is warmish and I have gas on the valve cover.
Well, I think I held my breath as much as you guys did. I kept yelling at my brother to get his face out of the engine compartment in case something flew out.
I'll post what little pictures I have tonight.
Well, I think I held my breath as much as you guys did. I kept yelling at my brother to get his face out of the engine compartment in case something flew out.
I'll post what little pictures I have tonight.
Congrats on finishing. Sorry it didn't go the first time.
My last injector sprayed fuel 3 times (I think) before we got it seated properly. I then lubed up the o-rings with a bit of WD-40, and it popped on properly. Like I mentioned previously, my Toyota tech said you should always lube the injectors when putting them back onto the rail.
At least, popping off the fuel rail and reseating the injectors doesn't require removing anything else. Just un-snipping the zip ties holding the cable bundle to the rail.
Anyhow, good luck tomorrow when you try again! We'll be waiting!! 😁
My last injector sprayed fuel 3 times (I think) before we got it seated properly. I then lubed up the o-rings with a bit of WD-40, and it popped on properly. Like I mentioned previously, my Toyota tech said you should always lube the injectors when putting them back onto the rail.
At least, popping off the fuel rail and reseating the injectors doesn't require removing anything else. Just un-snipping the zip ties holding the cable bundle to the rail.
Anyhow, good luck tomorrow when you try again! We'll be waiting!! 😁