I'm excited to get a tach and put it in now, but am missing one last detail. What do I set the redline at? I just want to know how high in the rpms that I can ride up into without redlining. I have an 07 liftback 5 spd if that makes a difference.
DIY: TACH INSTALLATION INSTRUCTIONS
216 posts · 192,823 views · page 3 of 5
Replies continued
nvm, just saw on toyotanation that the yaris has a rev limiter somewhere around 6200. anyone know if this is accurate?
pretty sure that is correct. i wouldn't go no higher than that.
Yeah it's around there. I've only done it once since I've had my tach installed.Originally Posted by TickleTimeTim ↑nvm, just saw on toyotanation that the yaris has a rev limiter somewhere around 6200. anyone know if this is accurate?

^ Now that's just awesome.
my first mod... i had to share. anyway i'd like to say this thread helped but i guess i'm just not that handy with this type of stuff. paid someone to do this... i think it turned out well. i didn't realize how much overkill an 8000rpm tach would be but oh well it's on there now.
Picture lost · img3.imageshack.us
Picture lost · img3.imageshack.us
Picture lost · img3.imageshack.us
Picture lost · img3.imageshack.us
Picture lost · img3.imageshack.us
Picture lost · img3.imageshack.us
Did they change the guage colors to orange for '09?Originally Posted by frownonfun ↑my first mod... i had to share. anyway i'd like to say this thread helped but i guess i'm just not that handy with this type of stuff. paid someone to do this... i think it turned out well. i didn't realize how much overkill an 8000rpm tach would be but oh well it's on there now.
i'm guessing so. its not just the pic if that's what you mean. it's pretty orange in person. i had an 07 sedan and i could have sworn the gauge lights were whiter but couldn't remember since i sold it not long after i bought it.
I have an A/T, so I use the Scanguage tach.😎
stuck. got the glowshift 7 color with shift light. red in 24, grounded, and illumination in fuse 31 (meter and gauge) it is lit up (red) can't change color and can't figure how to connect ecu cable. don't know wether to jam the cord down in the port or to cut and tie?
so, back light flickers on tach, but when i rev the color stays solid. ( still can't get needle to move) what's going on?
If the light is flickering your illumination wire must not be hooked up securely, or you have a bad tach. The vibration from revving must be knocking it into place? 🤷
Just a thought/guess.
Just a thought/guess.
had the green and yellow mixed up...ha. magic.
All good now then?
hah. yeah, thanks for quick reply
Np, post a pic of it. =)
took some crappy pics off of my black berry, will have them posted soon.
only two problems:
1. tach not very well lit during day (like i said, i used fuse 31, meter and guage)
2. after puting it in, i gave it a rev or two and right before reaching idle again the car slightly shakes. not sure if it always did that or if i'm just nervous that i might have screwed something up.
other than that, thanks everyone for the help. thanks thewifesyaris for the glowshift.
crappy pics will be up shortly.
only two problems:
1. tach not very well lit during day (like i said, i used fuse 31, meter and guage)
2. after puting it in, i gave it a rev or two and right before reaching idle again the car slightly shakes. not sure if it always did that or if i'm just nervous that i might have screwed something up.
other than that, thanks everyone for the help. thanks thewifesyaris for the glowshift.
crappy pics will be up shortly.
hey so i have my tach installed but how can i be sure it is giving me the right reading? i hear people talk about hitting 2500rpms and up to like 5000rpms and this makes me wonder if something isn't hooked up right cause i am not getting anywhere near that on my tach. my engine sounds like it is going to explode at around 2600rpms so i really haven't gotten much higher than that. i just assumed 3000 was redline from the way it sounds when i rev that high.
any thoughts?
any thoughts?
Has your Tach got pre set cycliders 2,4,6,8Originally Posted by frownonfun ↑hey so i have my tach installed but how can i be sure it is giving me the right reading? i hear people talk about hitting 2500rpms and up to like 5000rpms and this makes me wonder if something isn't hooked up right cause i am not getting anywhere near that on my tach. my engine sounds like it is going to explode at around 2600rpms so i really haven't gotten much higher than that. i just assumed 3000 was redline from the way it sounds when i rev that high.
any thoughts?
if so set it too 2 and it will read properly.the yaris has twin coils
and you are only taking the reading from one of them. 👍
i don't think it can be set at 2... only 4, 6, and 8. and it is on 4 right now so idk.
Maybe you are thinking of the SunPro as shown in posting #84 ?Originally Posted by Thirty-Nine ↑Okay ... I think I need to get a tach. Someone makes/made a thin tach (I think) that would still allow you to use your driver's side glove box. Anyone knows who makes that slim tach?
DIY: TACH INSTALLATION INSTRUCTIONS
I have a white one, but haven't installed it. I like the looks of the black one.
They are hard to find now. I got mine on eBay a long time ago for use with
my Geo Metro, but never installed it there, either. I paid about $40 several
years ago. I've seen them on eBay now and then.
CP2010 is black face, CP2012 is white face.
Here is one place it is listed, but not sure if in stock:
http://www.tradervar.com/3-1-2-Perfo...pro-P35409.htm
I've been contemplating a ScangaugeII installation.
8000 rpm tach is right. The engine redlines at 6400 (I think). Set your shift light at 5000.
Speedhut Tach. Mounted with 3M tape (the good stuff). Yes, it clears the glove box behind the wheel - no problem.
Pricy but perfect for the need IMHO. Build your own here: http://www.speedhut.com/custom_gauge...number-694.htm



Pricy but perfect for the need IMHO. Build your own here: http://www.speedhut.com/custom_gauge...number-694.htm




thats looks nice and clean... i like that one.
Why didn't you just buy a center cluster with a tach in it?
They are expensive ($600) and there was much unresolved debate on this forum as to whether or not it would be a simple swap.Originally Posted by daf62757 ↑Why didn't you just buy a center cluster with a tach in it?
On that topic though - it still boggles my mind how Toyota reasoned that not including a tach in all MT Yarii - while including them with the AT's - was a good decision. So, yeah, I wish mine had come with the tach cluster, but it didn't so I bought one and installed it.
I agree, it looks great. Didn't realize that 3M tape was that good forOriginally Posted by frownonfun ↑thats looks nice and clean... i like that one.
that type of installation. Being that my car is new, I am leery of drilling
holes, though if I took my time, I could do it right. 😛
im diging the center mount.
Finally got around to installing my Sunpro tach in my '08 today. Thanks to all of you for your information! Couldn't have done it without this thread.
I used all of the same connections, except that the bottom left wire coming out of the OBD port in my '08 was orange, not blue-green. I think someone mentioned that his '09 was orange as well.
Sorry no pics, but it looks pretty much the same as everyone else's 2 5/8 inch tachs..
I used all of the same connections, except that the bottom left wire coming out of the OBD port in my '08 was orange, not blue-green. I think someone mentioned that his '09 was orange as well.
Sorry no pics, but it looks pretty much the same as everyone else's 2 5/8 inch tachs..
What tach is that? does it clear the glove box?Originally Posted by MR. CANTON ↑
I also installed my tach last week using this thread. The only thing I did differently was run the lighting wire to the power wire so the gauge is always backlit.
Here's My tach install
I used the instructions on this thread with one change (I hooked the dimmer to the stereo dimmer seeing as the new head unit didnt use it anymore)
I also chose to mount it in the upper glove to try to make it less noticeable. In hind sight, I wish the Tach itsself was a little larger and easyier to read, but hey, I can always get a bigger one later
Here are some pics



The Ground Wire

The Tach signal Wire

The power Wire

Im still a little unsure about how safe it is to be running the power wire from the fuse box like I did I gess I can always change it later too.
I used the instructions on this thread with one change (I hooked the dimmer to the stereo dimmer seeing as the new head unit didnt use it anymore)
I also chose to mount it in the upper glove to try to make it less noticeable. In hind sight, I wish the Tach itsself was a little larger and easyier to read, but hey, I can always get a bigger one later
Here are some pics



The Ground Wire

The Tach signal Wire

The power Wire

Im still a little unsure about how safe it is to be running the power wire from the fuse box like I did I gess I can always change it later too.
I'm trying to understand how to install a tach. I've been attempting to research on here, read through this thread, and find what will be best for me (as I'm sure most of you have seen my different posts on this subject by now).
My question is this, can this be done without drilling holes anywhere in either the dash or other places? I'm sure I can mount the actual tach to the steering column using velcro or a strong doublesided tape. However, I am concerned about the wire routing. Is it possible? Has anyone done something like this?
Truthfully, being as I don't know that much about these kinds of wiring (I've done stereo installs only), the pictures that are here help, but I don't completely understand their orientation to the vehicle itself. Can someone help explain?
My question is this, can this be done without drilling holes anywhere in either the dash or other places? I'm sure I can mount the actual tach to the steering column using velcro or a strong doublesided tape. However, I am concerned about the wire routing. Is it possible? Has anyone done something like this?
Truthfully, being as I don't know that much about these kinds of wiring (I've done stereo installs only), the pictures that are here help, but I don't completely understand their orientation to the vehicle itself. Can someone help explain?
I didn't have to drill any holes for mine. If I ever remove it all I would have to do is clean up the 3M tape residue and no one would ever know it was there.Originally Posted by DevilGirl ↑I'm trying to understand how to install a tach. I've been attempting to research on here, read through this thread, and find what will be best for me (as I'm sure most of you have seen my different posts on this subject by now).
My question is this, can this be done without drilling holes anywhere in either the dash or other places? I'm sure I can mount the actual tach to the steering column using velcro or a strong doublesided tape. However, I am concerned about the wire routing. Is it possible? Has anyone done something like this?
Truthfully, being as I don't know that much about these kinds of wiring (I've done stereo installs only), the pictures that are here help, but I don't completely understand their orientation to the vehicle itself. Can someone help explain?
So I was just showing this thread to my boyfriend. He doesn't like how in the pictures people have tapped into the OBD port for the rpm readout. As he put it, "it voids the warranty like a sunofabitch." Is there a way to create a OBD plug-in for any regular aftermarket dial tach, so that no wires are actually snipped in this process?
Warranties are voided by tapping wires, unless something is damaged by doing so. The tach signal on the OBDII connector is there for diagnostic purposes.
You could purchase a J1962 male connector to plug into the OBDII port to grab the tach signal, but you'd still need to grab power and an illumination from wires under the dash.
You could purchase a J1962 male connector to plug into the OBDII port to grab the tach signal, but you'd still need to grab power and an illumination from wires under the dash.
I've done mods like that and never ever had a problem with dealer servicing, never been questioned about things like tachs etc. This is something for each person to choose what is comfortable for them, and depends somewhat on their relationship with the dealer.
On my Yaris, I know a dealer is never going to see it for servicing again, so my choice with this one is easy. 🙂
On my Yaris, I know a dealer is never going to see it for servicing again, so my choice with this one is easy. 🙂
It's relatively easy to install a tach in the Yaris as all the wire connections that are required can be made in the same general location, right near the steering column.
No drilling, etc is nessary if you use double sided tape to mount the tach.
Personally, I installed a "Speed Hut Revolution tach" (after seeing Altitude's post and pics) and really like it. 🙂
No drilling, etc is nessary if you use double sided tape to mount the tach.
Personally, I installed a "Speed Hut Revolution tach" (after seeing Altitude's post and pics) and really like it. 🙂
I didn't tap the tach wire. I left the end of the signal wire from the tach bare and twisted (tinning it with solder would probably have been better) and just stuck it into the tach wire hole on the OBD connector and put a small drop of glue on it to hold it in place. It can be easily removed.Originally Posted by DevilGirl ↑So I was just showing this thread to my boyfriend. He doesn't like how in the pictures people have tapped into the OBD port for the rpm readout. As he put it, "it voids the warranty like a sunofabitch." Is there a way to create a OBD plug-in for any regular aftermarket dial tach, so that no wires are actually snipped in this process?
There are a couple of options for the power and lighting but you'll likely have to tap the lighting unless you want to wire the tach's backlight as always on with the 12v. You can use one of those fuse taps that connect at the fuse box.
Just finished installing my tach, but I haven't connected the illumination wire. I don't know which way to go, the brown wire from the dimmer or the #9 fuse?
I'd like to have dimming for this one, but I guess I can live without it, I prefer connecting it to the fuse even if that doesn't give me dimming. Can anyone confirm?
I'd like to have dimming for this one, but I guess I can live without it, I prefer connecting it to the fuse even if that doesn't give me dimming. Can anyone confirm?
I connected my tach's illumination wires to the #2 fuse (Panel1).Originally Posted by fmicle ↑Just finished installing my tach, but I haven't connected the illumination wire. I don't know which way to go, the brown wire from the dimmer or the #9 fuse?
I'd like to have dimming for this one, but I guess I can live without it, I prefer connecting it to the fuse even if that doesn't give me dimming. Can anyone confirm?
I also added a "dimmer" that you might be intetresed in.
An easy way to dim AM tach lights...
Finally got this project done. Cutting the hole in the glove compartment with only a 1/8" drill and sand paper was a bitch... Quite happy with the result though 👍
I also connected the illumination wire to the illumination fuse in the fuse panel. Don't remember the number by heart, but it's in the owner's manual. So I get the tach light on whenever all other instruments are lit.
Picture lost · pgu4qw.blu.livefilestore.com
Picture lost · pgu4qw.blu.livefilestore.com
Picture lost · pgu4qw.blu.livefilestore.com
I also connected the illumination wire to the illumination fuse in the fuse panel. Don't remember the number by heart, but it's in the owner's manual. So I get the tach light on whenever all other instruments are lit.
Picture lost · pgu4qw.blu.livefilestore.com
Picture lost · pgu4qw.blu.livefilestore.com
Picture lost · pgu4qw.blu.livefilestore.com
So what if your tach signal wire on the OBDII plug is orange instead of greenish-blue? I have an '08 3-door M/T.
Later models do no have the greenish-blue wire for the tach.
My '09 for example has a brownish wire for the tach.
Just use the wire that is in the correct position regardless of what the color might be.
My '09 for example has a brownish wire for the tach.
Just use the wire that is in the correct position regardless of what the color might be.
WILCO, thanx
Ok, next question, got the tach mounted and hooked up. Its an 8,000 rpm tach and it for reads perfectly up to 3,500rpm, but it for some reason won't budge any further. Ant ideas? Thanks
Defect? Can you see any obstruction that would prevent the needle from moving?
I guess it could be a defect. I have everything hooked up except the Illumination wire, and I don't believe that matters.
Its a 4,6,8 cylinder model and the switch is set on 4.
Its a 4,6,8 cylinder model and the switch is set on 4.
Yeah, if it doesn't want to move past 3500 rpm, there must be something wrong inside...