IdjiitOriginal postHolly Springs, NC · Apr 20, 2006#1Sorry to lag on this, I did it a couple weeks ago but haven't had time to prep the photos.
Start by removing all items under the storage hatch by "unlocking" the items:
Picture lost · www.swiftbennett.com Note the spare holder which protrudes above the relatively "flat" back - bummer #1.
Picture lost · www.swiftbennett.com You'll see that the seat frame is held on by 4 External Torx nuts (the other two are under the bottom seat):
The bottom seat frame is connected by two bolts, but removing these isn't enough to remove the seat. If you're planning on putting in a flat deck, you'll want to use this to mount to anyway, so don't remove it.
Picture lost · www.swiftbennett.com Instead, remove the seat by using a pair of pliers or a screwdriver to press in the tabs holding the seat cushion to bottom seat frame. Warning: This does
not work like Scion bottom seats - if you try to force it, you'll rip the seat! (note - front of seat at the top of the photo, which is where the tabs are)
Picture lost · www.swiftbennett.com Close-up of tabs:
Picture lost · www.swiftbennett.com Removing the seat will show the next two torx bolts which screw through the back seat frame to the bottom seat frame. Remove these bolts, pull out the seat and replace the bolts (you'll probably want to use some 3/8" washers since the hole in the bottom seat frame is pretty big.
Picture lost · www.swiftbennett.com After removing everything you'll see bummer #2 - another protrusion with a cable coming out, which I'm assuming is the gas tank.
Picture lost · www.swiftbennett.com Lower angle shows the problem. If you want to put in a deck (like I have), you're going to have to add about 2 inches of height to clear the gas tank and spare holder:
Picture lost · www.swiftbennett.com Top view with everything removed:
Picture lost · www.swiftbennett.com In total it's about 100lbs saved if you're not going to keep a spare in the car. My big question is whether the back seat frame is actually a structural member. It's a pretty hefty bar...
Replies 85
riceboyCAN · Apr 20, 2006#2Nice removal of the rear seats.. I was just wondering if there was any specific reason for doing this besides the weight savings.. Are you planning on tracking, racing, auto-x the Yaris, or perhaps you've got a real nice audio/video setup planned???
IdjiitThread starterHolly Springs, NC · Apr 20, 2006#3It's for increased storage. I'm a photographer, and so I plan on having the bottom be completely flat to store various cases, then another platform will go on top of that (which will actually be two fold-out tables) then my dogs on top of that, with a little more storage for suitcases, camera cases, etc.
The idea is that I can have sort of a "hidden storage" area so I can keep my heavy cases in the car overnight (with an alarm) for shooting weekends where I don't want to drag 200lbs of gear up stairs every night. So I'd just bring in my cameras/laptops and leave everything else in the car. If someone looks in, all they'll see is the flat deck, which will be locked to the bottom.
stuffyontario, canada · Apr 20, 2006#4that's really interesting idjiit, thanks for the step-by-step
riceboyCAN · Apr 20, 2006#5Wow sounds like quite an undertaking, make sure to keep us posted on how that turns out for you!
IdjiitThread starterHolly Springs, NC · Apr 20, 2006#6Will do. Yeah, it's pretty ambitious. I need to find a shop locally that can do aluminum fabrication. I already have a combo aluminum/wood base for the back just to get an idea of how everything can fit together realistically, but the final fab work is way beyond what I can do with screws and square stock.
DJ_SpaRkyGroveland, FL (Near Orlando) · Apr 20, 2006#7 Originally Posted by Idjiit
Picture lost · www.swiftbennett.com
Picture lost · www.swiftbennett.com
In total it's about 100lbs saved if you're not going to keep a spare in the car. My big question is whether the back seat frame is actually a structural member. It's a pretty hefty bar...
The seat fram kinda looks like a crossbrace or something, just add some bars to the B-Pillars.
IdjiitThread starterHolly Springs, NC · Apr 20, 2006#8I'm actually referring to the seat back frame, not the bottom seat frame. The back seat frame is extremely sturdy (and heavy) steel, not aluminum like the bottom seat frame, which I only keep to act as a base for my platform.
DJ_SpaRkyGroveland, FL (Near Orlando) · Apr 20, 2006#9 Originally Posted by Idjiit
I'm actually referring to the seat back frame, not the bottom seat frame. The back seat frame is extremely sturdy (and heavy) steel, not aluminum like the bottom seat frame, which I only keep to act as a base for my platform.
Word, but that bottom piece does look alot like a cross-brace.
IdjiitThread starterHolly Springs, NC · Apr 20, 2006#10 Originally Posted by DJ_SpaRky
Word, but that bottom piece does look alot like a cross-brace.
Yeah, I doubt it is. I think if it was structural it would be stronger or have some diagonals in it. Looks like it's designed more to keep asses in place, not wheels. ;)
why?harnett county NC · Apr 20, 2006#11If either was structural, you would not be able to remove them at all. Like on the last gen Camry's, the rear seats didn't fold and you could tell the backs were part of the structure.
In the picture it looks like there are 4 bolts at the corners of that big metal thing. Could it be possible that the white metal thing isn't actually the bottom of the car, or are those bolts all holding something else down?
Also, it almost looks like the spare tire thingy can come off.
I'm prolly stating silly things, but you never know.
Thanks for the pics.
IdjiitThread starterHolly Springs, NC · Apr 20, 2006#12With the exception of the black frame, everything that can come off is off. The spare tire holder looks like it's riveted from below. It's possible it's screwed, but I doubt it. Not sure what white thing you're referring to is. In the back on the side of the spare area, the 4 screws are just holding down the plastic cowling for the wheel wells which basically just cover up the metal of the car, not much space savings there.
why?harnett county NC · Apr 20, 2006#13The white thing is the bottom of the car, lol.
IdjiitThread starterHolly Springs, NC · Apr 20, 2006#14lol, sorry... overexposed the photos a bit. Yeah, anything that's silver/white is the body of the car. ;)
AutoTech1Farmington NY · Apr 28, 2006#15You should find a way to get the frame out of there. That could be a good twenty lbs shaved or somewhere in that area... I don't know. But I'm sure it wieghts a good amt...
IdjiitThread starterHolly Springs, NC · Apr 28, 2006#16It really isn't that heavy. Anything I would build to replace it would likely be heavier.
SophieSleepsMA · May 24, 2006#17idjiit, you're my type of modder.
If I had a yaris I'd be doing the same thing as you.
Since you seem like a person who is truly a DIYer, and you have access to some plain steel (from your other post).
I assume you have either a MIG welder or access to one. If not, they really aren't as expensive as they were before.
You could turn that possible structural seat frame into something usefull for storage. Some square tubing as a base, some flat steel as a frame and some plexi would be fairly lightweight and a good way to organize.
If that frame is something you need, why not keep the base for it's intended purpose but now make something that need out of it.
IdjiitThread starterHolly Springs, NC · May 25, 2006#18 Originally Posted by SophieSleeps
If that frame is something you need, why not keep the base for it's intended purpose but now make something that need out of it.
Yeah, I'm keeping the seat base for the storage I'm currently building. I'm going with aluminum and not welding since I don't know how, but it's a pretty cool solution. I'm about 33% of the way through and will have a big post once it's all done.
In the meantime, I've tapped out aluminum square stock supplies out of every Lowes and Home Depot within a 20mi radius. 😆 I should have just made a big bulk order somewhere - probably would have been a hell of a lot cheaper.
SnakeNew York · May 26, 2006#19this weight reduction makes a big difference on the car, its night and day difference without the back seats
👍
Picture lost · www.hyespeeders.com
Jagovdallas texas · Aug 20, 2006#20Do the Torx bolts remove from underneath the car?
IdjiitThread starterHolly Springs, NC · Aug 20, 2006#21No, you just have to remove all the luggage-area covers, etc. to get to the back bolts and remove the seat cushion to get to the fronts.
MrMondayNiteNY/NJ · Oct 1, 2006#22Hi Idjiit, is it possible to swap a regular folding rear bench seat with a 60/40 split,reclining sliding rear seat? The reason I ask is would have to get the power package to get the split rear seat and we all know how hard that is to get right now. Thanks MrMondayNite
IdjiitThread starterHolly Springs, NC · Oct 2, 2006#23I can't imagine why it wouldn't be possible, but I don't know for sure.
IdjiitThread starterHolly Springs, NC · Oct 2, 2006#24I posted the finished setup
here.
Here's one of the photos:

eTiMaGoBangkok, Thailand · Oct 2, 2006#25that is sweeter than pure unrefined sugar 😁
PETERPOOPOahu · Nov 6, 2008#26Well I just did this today. I left the spare tire in the car because I can't risk missing class/work. After weighing what I took out, I believe i lost about 70lbs. Not really that much of a difference, but i NEVER had people or never will have people riding in my back seat. So when I decide to "race" people, i'll just make sure to take out my spare for the activity.
I left the board that covers the spare tire. I am going to put another small board going across and on top of the existing board (that covers the spare) to catch anything that would slide forward into the empty space where the seat was. I'm also going to put some velcro on the outside of the board so I can have the flaps stick to the board so you can't see what's in that "trunk" area if you look in through the windows..
This is where the board will be going. I'l going to put carpet on it so it'll blend in nicely.
Then put some velcro on the outside of the top so the flaps can stick on it and be nice a tight. not droopy
I put the rear floor mats over where there would be exposed metal from the car. I will eventually cover it with carpet once i put the board across. I'll post pics when that is all done.
DerKaiZeRsPerth WA · Nov 12, 2008#27finally I got information how to remove back seat 👍
pkayaustralia · Nov 18, 2008#28thanks i have been scraching my head how to get the seat cover on.
YarisPRMayaWest, Puerto Rico · Dec 10, 2008#29I did my seat delete(kinda) I haven't removed the upper part or the seat but in all the stuff I think there are a few usless pounds
Picture lost · i63.photobucket.com
cali yarisCanoga Park, CA · Dec 10, 2008#30rear 60/40 seats removed = 90.5 pounds
with rear seatbelts and all bolts = ~100 pounds
justjesusOrange County · Dec 10, 2008#31Idjiiit. Cool stuff. Giving me some ideas for my liftback. Thanks!
PeterPoop, thanks for showing those pics and the how-to
chongopantsHouston · Jul 8, 2009#32I am thinking of undertaking this project myself for the weight loss. To improve mileage and response time.
tk-421Dagobah · Sep 20, 2009#33I just did this myself... Took 20 mins max. and the difference was felt right away. The only thing I don't like too much is that there's increased noise levels in the back now... Time for some sound deadening, perhaps? 🙄
Also moved the stuff to its own thread here:
Photography Talk (Split Thread) frownonfunRGV, Texas · Oct 14, 2009#34a DIY on taking out the back seat and no one mentions the size of the TORX bolts? that would really be helpful.
CTScottUSA, CT · Oct 14, 2009#35 Originally Posted by
frownonfun ↑ a DIY on taking out the back seat and no one mentions the size of the TORX bolts? that would really be helpful.
They are E-10
In a pinch an 8mm socket will work as well. When I pull Crashy's rear seat I didn't have a set of external torx, so I went the 8mm route.
frownonfunRGV, Texas · Oct 14, 2009#36thanks CTScott. i went ahead and just bought a set. would have rather spent $5 on a single socket than $40 on a whole set i'll probably never use again but oh well. it was one of those "i'm on a mission from god or allah or some other higher power" sort of things. so i couldn't wait for an answer. lol.
after removal did anyone else notice you can hear your gasoline sloshing around. lol. i don't wanna hear that.
tk-421Dagobah · Oct 14, 2009#37Yup, I hear that too... Kinda freaked me out the first time I heard it 😁
N9QGSGeorgetown, KY · Oct 20, 2009#38Whats the purple, looks like a knob?
schleppyBoston, MA · Oct 21, 2009#39 Originally Posted by
frownonfun ↑ after removal did anyone else notice you can hear your gasoline sloshing around. lol. i don't wanna hear that.
I hear gas sloshing in mine, more exhaust noise, road noise, etc. The car sounds alive!
TinyGiantRochester, NH · Oct 21, 2009#40i've been thinking about how i would like to remove the back but i have friends carpool with me to movies here and there and wouldnt want to lose that
advocatelocation · Oct 21, 2009#41 Originally Posted by
schleppy ↑ I hear gas sloshing in mine, more exhaust noise, road noise, etc. The car sounds alive!
I love it. The car sounds like a monster now.
frownonfunRGV, Texas · Oct 21, 2009#42 Originally Posted by
N9QGS ↑ Whats the purple, looks like a knob?
that knob thing is what secures the spare tire. screws in.
and i can't say i'm enjoying all the extra road noise. there are so many roads out here that have their fair share of loose rocks and man does it sound like the car is taking a beating now that the back seat is out. i need to figure out what i'm gonna cover it with back there cuz not only is everything louder but it just looks terrible.
scapeBeaufort, South Carolina · Oct 21, 2009#43 Originally Posted by
TinyGiant ↑ i've been thinking about how i would like to remove the back but i have friends carpool with me to movies here and there and wouldnt want to lose that
ifyou have split rear seats, the backing of one of them might be able to be removed, so any extra people riding along wouldn't be TOTALLY out of luck. then again you could remove both backs and just have them lay down and take their chances hah
why?harnett county NC · Oct 27, 2009#44okay, silly question. did y'all use hand tools to get those darn things out, or drills of some type? I'm guessing drills, because nothing i can do can budge those suckers.
kacWest/Central Illinois · Oct 27, 2009#45nothing but hand tools to remove mine... wrench with an extension...
tk-421Dagobah · Oct 27, 2009#46+1
why?harnett county NC · Oct 27, 2009#47damn. i literally can't get the things to budge at all. maybe the wrench is too small...
tk-421Dagobah · Oct 27, 2009#48Yeah you may need more leverage... Maybe you can find a pipe that you can slide the wrench handle through?
why?harnett county NC · Oct 27, 2009#49well the front ones came off really easily. Bigger size though. I can't do anything to the rears, i have a feeling i've stripped them at this point...
In case you didn't already figure it out, this is my first time doing anything like this. I was able to remove the seat cushion and a few of the lower seat belt bolts, but i've given up on the brace for now. going to try again later on or tomorrow, and if i still can't get them i'm going to the store to see if i can get something that will help. I think it was removed once already by the peoples who installed my amp and when they put it back together i bet they way over tourqued it.
chongopantsHouston · Nov 1, 2009#50Has anyone weighed the rear bench with belts and all the junk behind it with spare? A weight chart would rock!, I dont have any way of weighing mine, plus its in storage.. please pm me if you guys do this...